tires AUDI ALLROAD 2000 Owners Manual

Electronic
speed limiter
Yo ur Audi may be factory equipped with
tires which are rated for a maximum speed
of 130 mph (21 0 km/h). This is less than the
maximum speed of your vehicle. To reduce
the risk of sudden tire failure and loss of
control should the vehicle be operated at ex­
cessive speeds, your Audi also has an elec­
tronic speed limiterwhi ch prevents your ve­
hicle from going faster than the tire speed
rating. See page 257.
If the vehicle approaches the tire speed rat­
ing, the engine control unit will shut off the
fuel injectors and you will notice an instant
Joss of engine power and drop in road
speed. The engine performance will return
to normal as soon as the speed has dropped
below approximately 125 mph (200 km/h).
If the vehicle road speed signal to
the engine control unit should fail,
the Malfunction Indicator Lamp will
come on.
If this occurs, see your authorized Audi
Dealer and have the cause located and cor­
rected. �W
ARNING
Always observe the posted speed
limits and adjust your speed to suit
preva iling road, traffic and
weather conditions. Never drive
your vehicle faster than the maxi­
mum speed rating of the tires
installed. CONT
ROLS AND EQUIPMENT
129

Cancelling speed limit
Press the test button for at least 1 second
when the yehicle is moving at a speed
above 3 miles (5 km/h). The display will
show the warning symbol crossed through
to confirm that the speed limit has been
cleared.
Speed warning 2
82
When the ignition is switc hed off, the driver
can store a permanent speed limit
warning in the unit. The
warning is shown in the display as de­
scribed. The warning symbol only goes out
once the road speed has fallen below the
stored value again.
We recommend to store this speed limit
v:' arning if you wish to be reminded of a par­
ticular speed limit in addition to speed limit
warning 1. (For instance when driving in
countries with general speed limits or if a
particular speed should not be exceeded
when winter tires are fitted, etc.)
Selecting speed limit
• Press the test button briefly with the
ignition switched off. The mileage re­
corder display will then light up.
• Press the test button again and hold for
at least 2 seconds. The speed limit currently
set appears in the disp lay.
• To change the speed limit, press the top
or bottom of the function selector switch for
the trip computer (see arrow illustration).
The speed limit displayed will then increase
or decrease by 6 miles (1 0 km/h ) at a time. CONT
ROLS AND EQUIPMENT
• A few seconds after the button is re­
leased, the display lighting goes out again.
Cancelling speed limit
P _ress the .test button briefly with the igni­
tion sw1tched off; the display will light
up. Press the test button again for at least
2 seconds: the display will show the .speed
limit currently set. Now press and hold the
"R eset" button for the trip computer until
the crossed-out warning symbol appears.
145

The
first 1,000 miles (1 500 km)­
and afterwards
Break-in period
During the first few hours of driving, the en­
gine's internal friction is higher than later
when all the moving parts have been broken
in. How well this break-in process is done
depends to a considerable extent on the
way the vehicle is driven during the first
1, 000 miles (1 500 kilometres").
For the first 600 miles
(1 000 kilometres):
As a rule of thumb:
• Do not use full throttle.
• Do not drive faster than 3/4 of top
speed shown on the speedometer.
• Avoid high engine speeds.
• If possible, avoid towing a trailer. �
WARNING
• New tires tend to be slippery
and must also be "broken-ln." Be
sure to remember this during the
first 300 miles (500 kilometres).
Brake gently. Avoid following
closely behind other vehicles or
other situations that might require
sudden, hard braking.
• New brake pads don't have the
best stopp ing power and must be
.. brok en-in" during the initial 100
to 150 miles (150 to 200 kilo­
metres) of normal city driving. You
can compensate for this by press­
ing the brake pedal more firmly.
This also applies later when new
pads are installed.
From 600 to 1,000 miles
(1 000 to 1 500 kilometres):
Speeds can gradually be increased to maxi­
mum permissible road or engine speed. VE
HICL E OPER ATION
During and after break-in
period
• Do not rev the engine up to high speeds
when it is cold. This applies whether the
transmission is in N (Neutral) or in gear. dib Do not drive with unnece ssarily C!1'5 high engine speeds -upshifting
early saves fuel, reduces noise and
protects the environmeht -see also
page 195.
After the break-in period
Do not exceed maximum engine
speed under any circumstances. Up­
shift into the next higher gear before reach­
ing the red area at the end of the tachome­
ter scale -see page 117.
Excessive engine speeds are automatically
reduced.
193

------------------------VEHICLE
OPERATION
Operate your vehicle economically and
• Do not drive if you are tired.
Make frequent rest stops, at least after ev­
ery two hours of driving.
• Always adapt vehicle speed to
traffic, weather and road condi­
tions.
Remember that especially on smooth, slip­
pery roads, vehicle handling and braking de­
pend a great deal on tire adhesion. On wet
roads, the front wheels can hydroplane es­
pecially at higher speeds. If this happens,
you will then, no longer be able to steer or
brake properly.
• Always observe the posted speed
limits and use common sense. Your
good judgment can mean the differ­
ence between arriving safely at your
destination and having an accident.
Additional information regarding safety can
be found in the individual chapters of this
manual. minimize
pollution
Va rious factors influence fuel consumption:
engine wear, brakes and tires, environmen­
tal impact.
This chapter addresses some of these
points.
Yo ur personal sty!e of driving
wi II determine the economy of your vehicle,
as well as exhaust and noise levels.
«i? Do not let your vehicle stand and
, warm
up.
When the engine is idling, it takes a very
long time to warm up. Moreover, during
warm-up, both engine wear and exhaust
gas emissions are very high. Therefore, be
ready to drive off immediately after starting
the engine and avoid high engine speeds.
«i? Avoid full throttle.
Accelerating gently reduces fuel consump ­
tion, engine wear, and does not disturb the
environment. <£&#39;
Avoid driving at high speed.
Fuel consumption, exhaust emissions and
engine noise increase disproportionately at
high speeds. If you drive at approximately
three quarters of top speed, fuel consump­
tion will be reduced by one half. Never drive
faster than the posted speed limit and
weather conditions permitting.
r.:Cib Drive as smoothly as possible
W5 and keep a lookout ahead.
Unn ecessary accelerating and braking in­
crease fuel consumption and disturb the en­
vironment.
r.:Cib Switch off your engine if you are
W5 caught in a traffic jam. This
saves fuel and reduces emissions.
195

VE
HICLE OPERATION------------------------
The external conditions
in which you drive also affect your fuel con­
sumption.
The following conditions increase fuel con­
sumption:
• Heavy traffic, especially in large cities
with many traffic lights.
• Stop-and-go driving, especially short dis­
tances so that the engine never warms up
as it should.
• Driving in heavy, slow moving traffic in
low gear so that the engine speed is rela­
tively high when compared to the distance
driven.
� Plan your trips ahaad of time. Or­
� ganizs your trips to include sev­
sral errands and to avoid heavy traf­
fi c.
Of course, there are some conditions that
will affect fuel consumption that you can&#39;t
control.
For example, fuel consumption increases in
the winter or under difficult conditions (bad
roads, towing a trailer, etc.).
19 6 The
technical requirements
for optimum fuel consumption and eco­
nomy were &#39;&#39;built&#34; intoyourvehicle. Special
attention was paid to the environment. To
reta in and make use of these characteris­
tics, please note the following points:
riJ Use only unleaded gasoline.
Leaded gasoline causes damage to the cat­
alytic converter and other components of
the emission system.
t:Gh Have your vehicle serviced by an
� Audi Dealar at the specified in­
tervals -see page 228 and your
Main tenance booklet.
Having your vehicle regularly serviced by an
Audi Dealer helps ensure that it runs prop­
erly and economical ly, that it does not dis­
turb the environment, and that it has a long
service life. t:Gh
Check
your tire pressure once a
W month.
Low tire pressure increases fuel consump­
tion and tire wear, and impair s vehicle han­
dling.
�W ARNING
Underinflation and overloading of
tires can lead to tire failure. Sud­
den failur e on the road could cause
a serious or fata l accident. See
page 253 for inflation informa­
tion.
� Do not carry unnecessary items
in the luggage compartment.
Particularly in city traffic where you must
often accelerate, weight influences fuel
consumption.

VE
HICL E OPER ATION
Driving on slopes
• If you find that you cannot climb a grade,
never try to turn. Back down the hill in re­
verse gear. If you don&#39;t. the vehicle may
tip or roll over!
• To reduce the danger of rolling the ve­
hicle, drive the vehicle as close as possible
to the &#34;fall line&#34; (direction of maximum
slope) -not at an angle to the fall line.
If it feels like the vehicle is about to
roll over when you are trav eling at
an angle to the fall line, turn into the
fall line immediately.
• Never park your vehicle on extreme
uphill or down hill slopes.
Deep snow
• You should promptly install wheels
equipped with winter or all-season tires
when you expect winter road conditions -
see page 260.
• Install snow chains before attempting to
drive through deep, unplowed snow - see
page 261.
200 Driving
through water
• Always make certain that the ride level
system is in the highest level before cross­
ing streams and similar water obstacles.
• You should always determine how deep
the water is before you drive through it.
• When crossing through water, travel only
at a walking speed. If possible, do not
stop and do not shut off the engine.
• Avo id driving through salt water
(beaches, for example).
After you have traveled through wa­
ter, mud or slush, your brakes may
be slow to respond due to wet brake
rotors and pads. To get back the full
braking effectiveness, apply the
brakes cautiously to dry them out­
The brakes must be dry before you
can get full brake performance. Sand,
quicksand and similar unsta­
ble soils
Cross sandy or other unstable terrain briskly
and, if possible, do not stop.

Driving
with your quattro ®
The All Wheel Drive system has no operat­
ing controls that require attention.
The engine power is distributed automati­
cally to all four wheels for optimum effi­
ciency in all situations and road conditions.
The All Wheel Drive concept is perfectly
matched to the engine power of your
Audi all road. This combination gives the ve­
hicle excep tional handling and performance
capabilities, both on normal roads and in ex­
treme conditions of ice and snow.
However, it is vital to observe the following
safety notes:
�W ARNIN G
Always adjust your driving to road
and traffic conditions. Do not let
the extra safety afforded by All
Wheel Drive tempt you into taking
extra risks.
Although the All Wheel Drive is
very effective, always remember
that braking capacity is limited by
tire traction. You should therefore
not drive at excessive speeds on
icy or slippery road surfaces. ftl
WARNING continued
On wet road surfaces, be careful
not to drive too fast because the
front wheels could begin to slide
on top of the water (hydroplaning).
If this should occur, you will have
no warning from a sudden in­
crease in engine speed as with a
front-wheel drive vehicle. Always
drive at speeds which are suitable
to the road conditions.
Replacing wheels I tires
All four wheels must always have the same
rol ling radius. Different tires on the front and
rear wheels may impair vehicle control and
will damage the All Wheel Drive because of
the constantly different wheel speeds. The
proper function of the system is not af­
fected by unevenly worn tires.
For more information, see page 255. VEH
ICLE OPER ATION
Using winter tires
When driving in the winter, your vehicle
with All Wheel Drive has an advantage,
even with regular tires.
You should promptly install wheels
equipped with winter or all-season tires to
better handling and braking characteristics.
See also &#34;Winter tires&#34;, page 260.
207

VEHICL E CA
RE----------------------------------------------------
Notes
• Do not wash the vehicle in direct sun­
light.
• If the vehicle is rinsed with a hose, do not
direct the water into the lock cylinders -
otherwise they may freeze up in the winter.
�W ARNING
• Do not wash, wax or dry the ve­
hicle with the engine running.
• Do not clean the underside of
chassis, fenders, wheel covers,
etc. without protecting your
hands and arms. You may cut your­
self on sharp-edged metal parts.
• Moisture and ice on brakes may
affect braking efficiency. Test the
brakes carefully after each vehicle
wash.
214 Washing
your vehicle with a power
washer
If you use a power washer, please note the
following:
• Always follow the operating instructions
for the power washer -especially for pres­
sure and spraying distance.
• Make sure that the jet on the spray hose
produces a &#34;fan shape&#34; spray. Do not use
a jet which sprays the water out in a direct
stream or one that has a rota ting jet.
• Water temperature should not exceed
140 °F (60 °C).
�W ARNING
Never wash tires with a jet that
sprays the water out in a direct
stream. This could invisibly dam­
age and weaken the tires, even if
they are sprayed from a relatively
long distance for a vary short
amount of time. Damaged and
weakened tires can fail and cause
accidents and personal injury. Headli
ghts
Do not clean your headlights with a dry
towel or sponge. They must be cleaned
with a moistened towel.
Never use a sponge designed for removing
dried-on insects, a kitchen scrubber or any
other similar product since the lens surface
can be damaged by scrat ching and scour­
ing.
When using high-pressure washing equip­
ment or steam-cl eaning units, never spray
the vehicle with the nozzle close the vehicle
surface and never aim the spray at the same
point for a relatively long period of time.
Polishing Please refer to the imp ortant information on
page 212.
Polish your vehicle only if the paint has lost
its shine and the gloss cannot be brought
back with wax. If the polish used doesn&#39;t
contain preservative compounds, the paint
must be waxed afterwards.
Do not treat matte- pain�ed and plas­
tic parts with polish or wax.

VEHI
CLE CARE
J&#39;4 WARN ING continued
• If you must work underneath
the vehicle with the wheels on the
ground, always make sure the ve­
hicle is on level ground. that the
wheels are always securely
blocked and that the engine can­
not be started. Always remove the
ignition key before anyone gets
under the vehicle.
Always make sure the transmis­
sion selector lever (automatic
transmission) is in &#34;P&#34; (Park posi­
tion) and the hand brake is firmly
applied.
• Always be extremely careful
when working on the vehicle. Al­ways follow commonly accepted safety practices and general com­
mon sense. Never risk personal in­
jury.
230 �
Changing the engine settings
will adversely aHect emission
levels. This Is detrimental to the en­
vi ronment and increases fuel con­
sumption.
Always observe environmental reg­
ulations when disposing of old en­
gine oil. used brake fluid, dirty en­
gine coolant, spent batteries or
worn out tires.

VEHICLE
CARE-------------------------
Tires I Wheels
Tires are important but often abused parts
of a vehicle. They not only influence comfort
and ride, but perform vital safety functio �s.
This section is intended to provide you w1th
imp ortant information regarding their prop­
er use, care and replacement.
• Be sure to inspect your tires at least ev­
ery 2,000 miles (3 000 kilometres) for wear
and damage.
• Damage to wheels and tires is not always
easy to see. If you believe that a tire or
wheel has been damaged, it is best to have
it replaced as soon as possible. Internal tire
damage can never get better or &#39;: heal&#34; it­
self, it can only get worse over t1me. Tire
damage can lead to tire failure and loss of
vehicle control. See your authonzed Aud1
Dealer for advice and assistance.
• Mark tires before removing them. Re­
mount tires on the same vehicle side be­
cause the rotation direction must stay the
same.
252 •
Store removed tires in a cool, dry and pre­
ferably dark place. Tires which are not on
wheels should be stored standing up.
• New tires may have different tread
depths due to the configuration and des!gn
by the tire manufacturers. When replacing
tires, use ones with matching tread depth.
�W ARNING
• Tires age even if they are not be­
ing used. Tires which are more
than 6 years should be used only in
an emergency and then with cau­
tion.
• Avoid damaging tires and wheel
rims. If you must drive over a curb
or other obstacle, drive slowly and
as nearly as possible at a right
angle. Frequently check tires for
uneven wear and damage. M
WARNIN G continued
• Remove embedded material.
• Replace worn or damaged tires
immediately.
• Replace missing valve dust
caps.
• Keep oil, fuel, brake fluid, etc.
away from tires.
• Keep tires inflated correctly.
New tires
New tires tend to be slippery and cannot of­
ferfull traction until they have been properly
broken in.
�W ARNING
To help avoid loss of control, al­
ways operate a vehicle with new
tires at lower speeds and with spe­
cial caution for the first 300 miles
(480 kilometres).