Lights AUDI Q2 2021 Owner´s Manual

Driver assist systems
Automatic deactivation
Cruise control system: currently unavailable.
See owner's manual
The cruise control system has been automatically
deactivated because the system has detected a
fault which could impair its function. Try switch­
ing the cruise control system on again later.
A WARNING
Do not resume the programmed cruising
speed if this is too high
for
the traffic condi­
tions - this can cause accidents.
Speed Limiter
Description
Applies to: vehicles with speed limiter
®
LIM
•

km/h
|

Fig.
95 Speed limiter:
©
LIM
100
km/h
illustration

BFV-0268

LIM
100
km/h
At speeds above approximately 30 km/h, the
speed limiter helps prevent the driver from ex­
ceeding a set cut-off
speed.
The indicator lamp

Q
Lights up as soon as you switch on the speed
limiter. Information is also provided in the head-
up display*.
Speed limiter displays
© - The speed limiter is in passive mode, but a
cut-off speed has
not
yet been set.

®
- The speed limiter is in passive mode, and a
set cut-off speed has been stored.
® - The speed limiter is activated. The indicator
lamp
BH
flashes briefly when the speed limiter is

applied.

A WARNING
- Always direct your full attention to the
road,

even when you are using the speed limiter.
It is always the driver who is responsible for
determining the speed and for keeping a
safe distance to the other vehicles on the

road.

- For safety reasons, the speed limiter must
not be used in adverse weather or difficult
driving conditions (such as ice, fog, loose
grit or gravel, heavy
rain,
etc.) - risk of
acci­

dent!
- Only accelerate quickly or use the kick-down
feature when the visibility and weather
con­

ditions are suitable, and when the road and
traffic conditions allow you do do so safely.
Before driving down a
long,
steep gradient, it
is advisable to reduce speed and select a low­
er gear. In this way you will make use of the
engine braking effect and relieve the Load on
the brakes.
Switching on
Applies to: vehicles with speed limiter

Fig.
96 Control lever for cruise control system (example)

•
Pull the lever to position © to switch the sys­
tem on.

•
Applies to vehicles with cruise control system
or Audi adaptive cruise control: To switch to the
speed limiter, press the button
®1)
until the
driver message
QQ
Speed limiter: selected ap­
pears in the instrument cluster. •

l)
On some equipment versions, the speed limiter is not
available and button
(B)
has no function.
106

Driver assist systems
Camera-based traffic
sign recognition
Description
Applies to: vehicles with camera-based traffic sign recogni­
tion

Fig.
97 Instrument cluster: Traffic sign recognition

Fig.
98 Windscreen: Camera window for traffic sign recog­
nition
Traffic signs detected by the system appear in
the instrument cluster display to keep you in­
formed of current speed restrictions and no-over­
taking zones
^>Fig.
97. Within certain system

limits,
it will display these additional traffic re­
strictions:

£5
///

s

G

^-if?

Speed limits in wet weather
Speed limits in foggy conditions (only dis­
played when the all-weather lights or rear
fog light are switched on)
Speed limits at certain times of day
Speed limits when towing a trailer
General notes
The traffic sign recognition system can detect
standardised speed Limit signs within the cam­
era's range of
vision.
It makes use of the naviga­
tion data to evaluate the detected speed limits
and show them on the display. Under certain
con­

ditions, the system will also display the legal
speed limits on roads without speed Limit signs.
The traffic sign for the currently detected speed
limit will flash on the display if
a
speed warning

threshold,
which has been set on the infotain­
ment system, is exceeded
^page
109.
Traffic sign recognition is not available in all
countries. For
a
current list, see the Internet (e.g.
www.audi.com). The system is also subject to
certain inherent restrictions and may be partially
or completely unavailable in the following situa­

tions:

- If visibility is impaired by snow,
rain,
fog or
heavy road spray.
- In dazzling light, e.g. from the sun or oncom­
ing traffic.
-At high speeds.
- If the camera's range of vision
^>Fig.
98 is im­

paired,
e.g. by dirt or stickers. Notes on clean­
ing
•=>
page 312.
- If the traffic signs are partially or completely

obscured,
e.g. by trees, snow, mud or other
vehicles.
- If traffic signs deviate from the standard ap­
pearance (round with red border).
- If traffic signs are damaged or bent.
- If matrix traffic signs are mounted on overhead
gantries.
- If traffic signs or routes have changed (naviga­
tion data out of date).
- If the system detects a speed sticker on a slow-
moving vehicle (such as a heavy goods vehicle).
WARNING
Always direct your full attention to the road
and surroundings, even when you are using
traffic sign recognition. The actual traffic
signs on your route always take precedence

over
the information on the display. It is al­
ways the driver's responsibility to assess the
traffic situation and take appropriate care.
- Under adverse conditions, the traffic sign
recognition system may misinterpret or fail
to detect traffic signs. It is therefore possi­
ble that the speed limit display may occa­
sionally be unavailable or even incorrect.
108

Driver assist systems

CO

<
O
rN rN
t-H
o <
- The traffic sign detection system does not
adjust the speed of your vehicle to the speed

limits.

The speed limit displayed in the instrument
cluster is given in the units applicable in a
particular country.
Controls
Applies to: vehicles with camera-based traffic sign recogni­
tion

-22.0-C

Fig.
99 Instrument cluster: Secondary display
Calling up the traffic sign recognition

•
Call up the first tab (on-board computer) using
the
GL>]
button on the multi-function steering

wheel.

•
Applies to vehicles with analogue instrument
cluster: Press the
LU]
button and select Traffic
signs from the menu.

•
Applies to vehicles with Audi virtual cockpit: Se­
lect the display for Traffic signs.
Displaying signs for trailers
You can also display speed limits which apply
specifically to vehicles towing a trailer1).

•
Select the following on the infotainment sys­

tem:
|MENU|
button > Car
>
left control button
Driver assist
>
Traffic signs
>
Automatic trailer
recognition.
Setting the maximum speed for a trailer
You can set the maximum speed permitted for

your
type of
trailer15.
If
you
do not enter
a
value,

x)
Applies to factory-fitted towing brackets only
the system will show the maximum national
speed limit for vehicles towing a trailer.

•
Select the following on the infotainment sys­

tem:
|MENU|
button Car
>
left control button
Driver assist
>
Traffic signs
>
Trailer: highest

speed.

Setting speed warning
You can set a warning threshold up to
15
km/h.
The traffic sign for the currently detected speed
limit will flash on the display if the selected
warning threshold is exceeded.

•
Select the following on the infotainment sys­

tem:
IMENU|
button > Car
>
left control button
> Driver assist
>
Speed warning
>
Traffic sign

based.

Secondary display
If the instrument cluster is currently showing a
function other than traffic sign recognition, the
speed limit will be displayed in the top right-
hand corner
^Fig.
99. If the system is able to de­
tect
a
temporary speed restriction in a given sit­

uation,
it will update the display accordingly.
Temporary speed restrictions are displayed in the
following situations:
- A temporary speed restriction for wet weather
is detected while the windscreen wipers are op­

erating.

- A speed restriction for fog is detected while the
vehicle's rear fog light or all-weather lights are
switched on.
- A speed restriction applying at certain times of
day has been detected and corresponds to the
time displayed in the instrument cluster.
- The vehicle is towing a trailer and the Automat­
ic trailer recognition option is activated on the
infotainment system. In this case, restrictions
applying to trailers are
displayed15.

© Note
- Your speed warning settings and the maxi­
mum trailer speed will be automatically
stored and assigned to the remote control
109

Driver assist systems

CO

< o rN
iv
rN
•-i

00
- In certain situations, the system may misin­
terpret driving manoeuvres and inappropri­
ately recommend a break.
- No acute warning is given if the driver falls
into a microsleep.
Instrument cluster display
Applies to: vehicles with rest recommendation

H
Rest recommended
If the warning lamp lights up and the message
appears, the evaluation of the steering input has
resulted in a rest recommendation. This is also
indicated by a warning tone. Take a break as soon
as possible.
The message may be displayed again once if nec­
essary.
Switching on/off
Applies to: vehicles with rest recommendation
Select the following on the infotainment system:

|MENU|
button > Car > left control button > Driv­
er assist > Rest recommendation.
© Note
If you switch off the system,
it
will remain
switched off the next time you switch on the

ignition.

Audi adaptive cruise
control
Description
Applies to: vehicles with Audi adaptive cruise control

»

Fig.
100 Sensor range
The adaptive cruise control is a combined speed
and distance control system. It assists the driver
by controlling the road speed and the distance to
the vehicle in front within certain limits imposed
by the system. The adaptive cruise control sys­
tem can accelerate and brake when it detects a
vehicle in front. This provides maximum comfort
both on long motorway journeys and in conges­
ted traffic (automatic gearbox*).
What can the adaptive cruise control do?
The adaptive cruise control uses a radar. The ra­
dar is subject to certain system limitations

opage
112.
When there is no traffic in front, the adaptive
cruise control works just like a normal cruise
con­

trol system by maintaining a constant speed.
When you draw closer to a vehicLe in front which
is detected by the system, the adaptive cruise
control matches your speed to that vehicle by au­
tomatically applying the brakes, and then main­
tains a constant distance (which you can adjust in
the settings). As soon as it detects no more
vehicles in front, the adaptive cruise control ac­
celerates back up to the cruising speed.
Applies to: vehicles with automatic gearbox
In congested traffic, the adaptive cruise control
can brake down to a standstill and accelerate
again (subject to general system limitations) un­
der certain conditions
*$page
115, Driving in
congested traffic. The traffic jam assist (active
lane assist)* can assist the driver in traffic jams
and heavy congestion
<=>page
117.
Which functions can the driver control?
When you switch on the adaptive cruise control,
you can set your current speed as the "cruising

speed"
^>page
113, Switching
on/off.

While you are driving, you can interrupt the
cruise control
opage
115 or change the speed
setting
Opage
114 at any time.
In addition, you can adjust the distance to
vehicles in front and the driving program for the
adaptive cruise control
^>page
116.

Ill

Driver assist systems
Setting the steering input time and
vibration warning
Applies to: vehicles with Audi active lane assist

You
can change the Audi active lane assist
set­

tings on the infotainment system to
suit
your in­
dividual preferences.

•
Select the following on the infotainment sys­

tem:
|MENU|
button > Car
>
left control button
> Driver assist
>
Audi active lane assist.
Steering
input1'

early: If this setting is selected, a continuous
steering input assists the driver to keep the
vehi­

cle in the middle of the lane.

late:
If this setting is selected, the steering is not
corrected until just before a wheel crosses a de­
tected Lane marking.
Vibration warning
You can switch the additional steering wheel vi­
bration warning on/off.
A WARNING
When the vibration warning is switched off,
no visual warnings are given in the instrument
cluster display if
you
cross a lane marking.
Your personal settings are stored automati­
cally and assigned to the remote control key
which is being used
W.

Emergency assist
Applies to: vehicles with emergency assist
The emergency assist takes over controL of the
vehicle in certain situations and can help to pre­
vent accidents. It is an extension of the active
lane assist and can use the functions of the adap­
tive cruise control system
<=>^.
The emergency
assist is activated when it detects that the driver
has stopped steering the vehicle.
Functions of the emergency assist
The emergency assist monitors the steering ac­
tivity of the driver. It detects if the driver is inac­
tive and gives repeated visual and audible warn­
ings as well as brake jolts prompting the driver to
take proactive control of the vehicle again. The
hazard warning lights are also switched on when
the first sharp brake jolt is given below
a
speed of
80
km/h15.

If the driver does not take over, the system inter­
venes by steering the vehicle (within the limita­
tions of the system) to keep it in lane, and by ap­
plying the brakes until the vehicle has stopped*.
In addition, the warning lamp || and a message
are displayed.
Requirements for using the emergency assist
- The active lane assist must be switched on and
ready to warn
^>page
124.
-The adaptive cruise controL must be switched
on and activated
^>page
113.
If any of the requirements for the active lane as­
sist
^>page
123 or adaptive cruise control

tapage
112 are not met, the functionality of the
system may be restricted or it may be deactiva­
ted automatically.
Interrupting the emergency assist
You can interrupt the emergency assist if it reacts
when it shouldn't
•=> A:

- Move the steering wheel. Or:
- Press the brake/accelerator. Or:
- Switch off the active lane assist via the button

<>
page 117, Fig. 110.
WARNING
- As the driver you are always responsible for
controlling the vehicle. Do not let the emer­
gency assist tempt you into taking any risks
when driving - this can cause accidents.

l)
This function is not available on all export versions.
126

Driver assist systems

CO

< o rN
r>
rN
t-H
o < 00
- The purpose of the emergency assist is to
assist the driver and to help prevent an
acci­

dent in case of an emergency. The protec­
tion provided by the system is still subject
to the prevailing physical limits - risk of
acci­

dent!
- Due to inherent system Limitations, false ac­
tivation of the system is possible - risk of ac­
cident! Interrupt the emergency assist if
necessary.
- Please observe the warnings for the adap­
tive cruise control
•=> A
in General notes on
page 112.
If the emergency assist is deployed, it will not
be available again until the next time the
igni­

tion is switched on.
Audi side assist
Description
Applies to: vehicles with Audi side assist

/——s—a~-^r—"x.

o5

s

• x •
CO

Fig.
117 Area covered by the radar sensors

Fig.
118 Warning lamp on exterior mirror
The side assist function
(lane
change assist fea­
ture) assists the driver in monitoring following
traffic and the blind spots on both sides of the
car. Within certain system limits, it warns you if
it detects vehicles approaching quickly or travel­
ling at about the same speed as your own vehicLe
in the area covered by the sensors
©^Fig.
117.
If it judges a lane change to be critical, the warn­
ing Lamp (5) on the exterior mirror lights up

^Fig.
118.
The warning lamp on the left-hand mirror assists
the driver when changing lane towards the left
and the warning Lamp on the right-hand mirror
assists the driver when changing lane towards
the right.
Information mode
As Long as you do not operate the turn signal, the
side assist will merely inform you of the presence
of vehicles that it has detected and judges to be

critical.
In this case, the warning lamp on the
rel­

evant exterior mirror will Light up at low intensi­
ty.
The intensity of the warning lamp in this infor­
mation mode is kept relatively low, so that it
does not distract you while you are looking at the
road in front.
Warning mode
If
you
operate the turn signal and the warning
lamp on the relevant exterior mirror flashes
brightly, the side assist is warning you of what it
judges to be a critical vehicle. Please check the
situation in the exterior mirror and by looking
back over your shoulder
•=> A
in General notes on
page 128.
Applies to: vehicles with Audi active lane assist
The warning lamp on the relevant mirror may al­
so flash when you have not operated the turn
sig­

nal.
If
you
come close to a detected Lane marking
and are in danger of Leaving your lane, the side
assist warns you of what
it
judges to be a critical
vehicle.
®
Not

You can adjust the brightness of the warning
lamp on the exterior mirror
^page
129.
127

Intelligent technology
Remember that the accident risk always in­
creases
if
you
drive fast, especially
in
cor­
ners
or
on a wet
or
slippery
road,
or if
you
follow too close behind the vehicle in front
of
you.
Please bear
in
mind that even
the

ESC
and
the
integrated systems cannot
compensate
for
the increased accident risk.
When accelerating
on
a uniformly slippery
surface
(for
instance
all
four wheels on
ice

or snow), press the accelerator gradually
and carefully. The driven wheels may other­
wise start
to
spin
(in
spite
of
the integrated
control systems), which would impair the
car's stability and could lead
to
an accident.
© Note
The ABS and ASR systems can only work
properly
if
a 11
four tyres have a similar de­
gree
of
wear. Any differences
in the
rolling
radius
of
the tyres can cause the system
to

reduce engine power when this
is not
de­

sired.

The systems can make noises when they in­
tervene.
Switching on/off

The ESC
is switched on automatically when
the
engine is started.

^OFF

1
y

CO
5
3
CO
Fig.
139 Centre console (top): ESC button

The ESC operates
in
several levels. Depending
on

which Level
is
selected,
the
stabilising function
of

the ESC
is
restricted
or
switched
off,
and the ve­
hicLe
is
stabilised
to
a greater
or
Lesser degree.
In the following special situations,
it
may be ad­
visable
to
switch on off-road mode
to
allow a cer­
tain amount
of
wheelspin:
- Rocking
the car
backwards and forwards
to
free
it
- Driving
in
deep snow
or
on Loose surfaces
- Driving with snow chains
- Driving
on
rough terrain when much
of
the car's
weight
is
lifted
off
the wheels (axle articula­
tion)
- Braking
on
unsurfaced tracks when driving
downhill

For
your own safety you should switch
off
the
off-

road mode
in
time.
Characteris­
tics
Operation
Indicator
lamps
Driver mes­

sages*

Off-road mode
on

The stabilising function
of

the ESC and traction controL
system (ASR)
is
restricted
Press the
&m
button brief­
ly-

1*1
Lights
up.

Stabilisation control (ESC):

offroad.
Warning! Restric­
ted stability
ESC/ASR
off

The stabilisation function
is

no Longer available
•=>
A-

ESC
and traction controL
system (ASR) are switched

off.

Press
the
&m
button
for

longer than
3
seconds.

•M and
IWHUrt*
liant UP.
Stabilisation control (ESC):
off. Warning! Restricted
stability
Off-road mode
off
or
ESC/ASR on
The stabilising function
of

the ESC and traction control
system (ASR) is fully availa­
ble again.
Press the
#*
button again.

|*|goes
out,
or^and

të&Éid*
go
out.
Stabilisation control (ESC):
on
146

Intelligent technology

/K
WARNING

- When applying
the
brakes
to
clean
off
de­
posits
on the
pads and discs, select
a
clear,
dry
road.
Be sure
not to
inconvenience
or
en­
danger other road users;
do not
risk an
acci­

dent.
- Never
let the car
coast with
the
engine
switched
off
(this can cause accidents).

(T)
CAUTION

- Never
let the
brakes "drag"
by
leaving your
foot on
the
pedal when you
do not
really
in­

tend
to
brake. This overheats
the
brakes,
re­

sulting
in
longer stopping distances
and

greater wear.
- Before driving down
a
long,
steep gradient,
it
is
advisable
to
reduce speed
and
select
a

lower gear.
In
this way you will make use
of

the engine braking effect and relieve
the

load
on the
brakes.
If
you
still have
to use

the brakes,
it is
better
to
brake firmly
at in­

tervals than
to
apply
the
brakes continuous-

Ly

-
If
the brake servo
is out of
action,
you must
apply considerably more pressure
to the

brake pedal than you normally would.
-
If
you
wish
to
equip
the
car with accessories
such as a front spoiler
or
wheel covers,
it is

important that
the
flow
of air to the
front
wheels
is not
obstructed, otherwise
the

brakes can overheat.

Electro-mechanical

power steering
Electro-mechanical power steering assists
the

driver when steering.
The degree
of
power assistance
is
adapted elec­

tronically,
depending
on the
speed.
Warning/indicator lamps
and
driver
messages
| Do not drive vehicle: steering defective
If the warning lamp lights
up
permanently
and

the message appears, there
may be
a power
steering failure.
Stop
the
vehicle
in a
safe place
as
soon
as
possi­

ble.
Do
NOT drive on. Obtain professional assis­

tance.

S
Steering malfunction: you can continue driv­
ing
If the indicator Lamp Lights up,
the
steering
re­

sponse
may be
heavier
or
lighter than usual.
In

addition,
it is
possible that
the
steering wheel
will
be off
centre when driving
in a
straight line.
Drive slowly
to
a qualified workshop and have
the

fault rectified.
Note
You
can
drive
on if
the warnina/indicator
g/

Lamp
||
or y
|
lights
up
only briefly
Four-wheel drive
(quattro)
Applies to: vehicles with four-wheel drive

On
quattro models
the
engine power is distrib­
uted
to all
four wheels.
General notes
On four-wheel drive vehicles,
the
engine power
is

distributed
to all
four wheels. The distribution
of

power
is
controlled automatically according
to

your driving style and
the
road conditions. Also
refer
to
^>page
145,
Electronic stabilisation con­
trol
(ESC).

The four-wheel drive
is
specially designed
to

complement
the
superior engine power
of
your

Audi.
This combination gives
the car
exceptional
handling
and
performance capabilities
-
both
on

normal roads and
in
more difficult conditions,
such
as
snow and
ice.
Even
so (or
perhaps espe­
cially
for
this reason),
it is
important
to
observe
certain safety points
<=> A-

Winter tyres
Thanks
to its
four-wheel drive, your
car
will have
plenty
of
traction
in
winter conditions, even with
•

148

Speech dialogue system
Speech dialogue system
How to use the speech
dialogue system
Applies to: vehicles with speech dialogue system

You
can operate many infotainment functions
conveniently by voice.
Important: The ignition and the MMI system
must be switched on
^>page
152, you must not
be talking on the phone, and the parking aid
must not be active.

•
To switch on: Briefly press the
0
button (J)

^>page
17, Fig. 12/(3)
^>page
18, Fig. 14 on
the multi-function steering wheel and give a
spoken command after the beep signal.

*•
To switch off: Press and hold the
0
button for
several seconds. Or: Press the
0
button.

•
To pause: Say the command Pause. To end the

pause,
press the
S
button.

•
To make a correction: Say the command Cor­

rection.

Input help
The system guides you through the input routine
with cues and messages.
- Input help messages on screen: After the
speech dialogue system is switched on, a selec­
tion of possible commands will be shown. The
command display can be switched on or off as

required.
Select:
|MENU|
button
>
Settings >
left control button > MMI settings
>
Speech
dialogue system.
- Spoken input help
cues:
To have the system
play the commands currently possible, switch
on the speech dialogue system and say Help.
How to help the system understand you
Speak clearly in a normal volume. Speak louder if
you are driving fast.
Speak in a normal tone without long pauses.
Close doors, windows and sun roof* to reduce
background noise. Make sure that passengers are
not talking when you say a command.
Keep the air outlets of the air distribution system
pointed away from the microphone, which is fit­
ted in the vicinity of the front interior lights in
the headliner.
The system should only be operated by the driv­
er, since the handsfree microphone is directed
towards the driver.
Other settings
Refer to
^>page
262.
© No
-The dialogue is paused when an incoming
telephone call is received; you can continue
the dialogue by ignoring the
call.
If
you
an­
swer the
call,
the dialogue will be cancelled.
- No navigation cues* or traffic announce­
ments are played when a dialogue is
run­

ning.

- You can select an entry from a list both via
the speech dialogue system and using the
rotary pushbutton.
- The speech dialogue system does not sup­
port commands in Arabic, Norwegian or
Hungarian.
Notes on the overviews
of commands
Applies to: vehicles with speech dialogue system
The following overviews show you the commands
that you can give to operate the MMI via the
speech dialogue system. •

A WARNING

- Please direct your full attention to the road
at all times! As the driver, you have full re­
sponsibility for the safety of the vehicle and
other road users.
For
this reason, you should
only use the functions in a manner that al­
lows you to maintain control of the vehicle
in all situations - accident risk!
- The speech dialogue system must not be
used in cases of emergency, since the voice
changes in stressful situations. This could
result in a failed or delayed telephone
con­

nection.
Always dial emergency numbers
manually!
164

Audi connect (infotainment)

CO

rN
IN
rN
•-H

00
Flight information
Applies to: vehicles with Audi connect (infotainment)
Information on flights and current arrival/depar­
ture times in the search area selected.

•
Select and confirm Flight information.
Train information
Applies to: vehicles with Audi connect (infotainment)
Information on bus stops, train stations and cur­
rent arrival/departure times in the search area

selected.

•
Select and confirm Train information.
You can use the right controL button to select the
train information you require.
City events
Applies to: vehicles with Audi connect (infotainment)
Information on events of different categories in
the search area selected.

•
Select: City events
>
left control button > a
cat­

egory.
Online news
Applies to: vehicles with Audi connect (infotainment)
With this service, you can call up the latest head­
lines from your preferred news providers in the

MMI.

Important: You must have subscribed to news
feeds via your myAudi account and your vehicle
must be connected to myAudi
<^>page
196.

•
Select: Online news > desired news feed
>
a
headline.
© Note
If
you
have not yet subscribed to any personal
news feeds in your myAudi account, pre-con-
figured news feeds will be shown.
Twitter
Applies to: vehicles with Audi connect (infotainment)

You
can
access
the most important functions of
your Twitter account via the MMI.
Important:
You must have linked your myAudi account to
Twitter. Further information can be found on the
Internet at my.audi.com.
You must have linked your vehicle to myAudi

opage
196.

•
Select: Twitter
>
left control button > function
desired (e.g. Trends).
You can choose the following categories in the
Twitter menu:
- My tweets: New tweets and tweets you have
composed are listed.
- Home: All the tweets from people you are
fol­

lowing are displayed.
-Trends: Topics currently being favoured for dis­
cussion within a particular country.
Different functions will be available depending
on the Twitter category you choose:
- New tweet: You can send a new tweet with the
help of ready-made templates or text blocks
created personally using myAudi.
- Refresh: The selected Twitter function is upda­

ted.

- Favourite: You can "favourite" a tweet to show

that
you like it.
- Retweet: You can repost a tweet to share it
with other people.
- Further settings (such as your account,
lan­

guage,
Tweet privacy, and location settings)
cannot be changed in the MMI. If
you
wish
to change anything in these menus, please
do so on the Twitter website itself.
- Further information on the individual
tem­

plates can be found online at my.audi.com.
- You can only connect one Twitter account to
your myAudi account.
199