warning AUDI Q3 2017 Owner´s Manual

Wheels
Quality grades can be found where applicable on
the tire side wall between tread shoulder and maximum section width
¢ page 171, fig. 147.
For example: Tread wear 200, Traction AA, Tem­
perature
A.
All passenger car tires must conform to Federal
Safety Requirements in addition to these grades.
Tread wear
The tread wear grade is a comparative rating
based on the wear rate of the tire when tested
under controlled conditions on a specified gov­
ernment test course.
For example, a tire graded 150 would wear one
and one half (1 1/2) times as well on the govern­
ment course as a tire graded 100.
The relative performance of tires depends upon
the actual conditions of their use, however, and may depart significantly from the norm due to
variations in driving habits, service practices and differences in road characteristics and climate.
Traction
The traction grades, from highest to lowest, are
AA, A, Band
C. Those grades represent the tire 's
ability to stop on wet pavement as measured un­
der controlled conditions on specified govern­ ment test surfaces of asphalt and concrete. A tire
marked C may have poor traction performance
¢&_ .
Temperature
The temperature grades are A (the highest), B,
and C, representing the tire's resistance to the
generation of heat and its ability to dissipate heat when tested under controlled conditions on
a specified indoor laboratory test wheel.
Sustained high temperature can cause the mate­ rial of the tire to degenerate and reduce tire life,
and excessive temperature can lead to sudden
tire failure ¢&. .
The grade C corresponds to a level of perform­
ance which all passenger car tires must meet un­
der the Federal Motor Vehicle Safety Standard
No. 109 . Grades Band A represent higher levels
188
of performance on the laboratory test wheel than
the minimum required by law.
A WARNING -
The traction grade assigned to this tire is
based on straight-ahead braking traction
tests, and does not include acceleration, cor­ nering, hydroplaning or peak traction charac­
teristics .
A WARNING
The temperature grade for this tire is estab­
lished for a tire that is properly inflated and
not overloaded. Excessive speed, underinfla­
tion, or excessive loading, either separately or
in combination, can cause heat buildup and
possible tire failure.
A WARNING
Temperature grades apply to tires that are properly inflated and not over or underinflat­
ed.
Tire pressure monitoring system
(l) General notes
Appl ies to: vehicles with tire pressure mon itoring system
-
Each tire, including the spare (if provided),
should be checked monthly when cold and inflat­
ed to the inflation pressure recommended by the
vehicle manufacturer on the vehicle placard or
tire inflation pressure label. (If your vehicle has
tires of a different size than the size indicated on
the vehicle placard or tire inflation pressure la­
bel, you should determine the proper tire infla­
tion pressure for those tires).
As an added safety feature, your vehicle has been
equipped with a tire pressure monitor ing system
(TPMS) that illuminates a low tire pressure tell­
tale when one or more of your tires is significant-
ly under-inflated. Accordingly, when the low tire
pressure telltale illuminates, you should stop and
check your tires as soon as possible, and inflate
them to the proper pressure . Driving on a signifi­
cantly under-inflated tire causes the tire to over­
heat and can lead to tire failure . Under-inflation ..,.

00
00
......
"' ,....
"' ...... 0 0 :::,
00
also reduces fuel e fficiency and tire tread life,
and may affect the vehicle's handling and stop­ p ing ability .
Pl ease no te that the TPMS is not a substi tute for
p roper tire maintenance, and it is the drive r's re ­
sponsib ility to maintain cor rect tire pressure,
even if under-inflation has not reached the leve l
to tr igger illum inat ion of the TPMS low tire pres ­
sure telltale.
Your vehicle has also been eq uipped with a TPMS
mal funct ion indicator to indicate when the sys ­
tem is not operating properly. The TPMS mal­
function indicator is combined w ith the low tire
pressure tellta le. Whe n the system detects a
malfunct ion, the telltale will flash for approx i­
mately one min ute and then remai n cont inuo usly
i llum inated. This sequence will continue upon
s ubseq uen t ve hicl e start- ups as long as the m al­
f u nction ex ists.
When the malfunct io n in dicator is ill uminated,
the system may not be ab le to detect or signa l
l ow tire press ure as intended . TPM S malfu nctions
may oc cur for a var iety of reasons, incl uding the
installation of replacement or alternate ti res o r
wheels on the vehicle that prevent the TPMS
from functioning properly . Always check the
TPMS malfunction telltale after rep lacing one or
more t ires or whee ls on your ve hicle to ensure
that the replacement or alternate tires and
wheels allow the TPMS to cont inue to funct ion
p roperly.
If the Tire Pressure Monitoring System
ind icator appears
A ppl ies to: ve hicles with Tir e Pressure Moni toring System in­
di cato r
The tire pressure indicator in the instrument
cluster informs you if the tire pressure is too low
or if th ere is a system malfunction .
Using the ABS sensors, the tire p ressure mo nitor­
i ng system compa res the tire tread circumfer ­
e n ce and vib ra tion characteristics of the individ u­
a l tir es .
If the pressure c hanges in o ne or more
wheels , th is is indica ted in the instrument clus ter
d is p la y with a n
[I] indica to r li ght and a message.
Wh eel s
If only one tire is affected, the location of tha t
t ir e will be indicated.
T he tire press ures mus t be store d in the Infot ain­
ment system again each t ime the pressures
c h ange (switching between partia l and full load
pressure) or after changing or replacing a tire on
yo ur vehicle
r::!;> page 190 . The tire pressure mon i­
toring system on ly monitors the tire pressure you
have stored . Refer to the t ire pressure label for
the recommended t ire press ure fo r yo ur vehicle
r::!;>page 181, fig . 150 .
Tire tread c ircumfe rence and vibration cha racter ­
istics can change and cause a tire pressu re warn­
i ng if :
- the t ire pressure in one or more tires is too low.
- the t ire has str uctural damage .
- t he t ire w as rep lace d or the t ire pressu re was
changed and it was no t store d
r::!;> page 190.
- t he spare tire* is i nstalled.
Indicator lights
[I] -Loss of pressu re in at leas t one tire r::!;> & .
Check the tires and replace or repair if necessary .
Check/correct the pressures of all fou r tires and
store the pressu re again in the menu disp lay
r::!;>page 190.
ffim (T ire Pressure Moni tor ing Sys tem) Tire
pre ssure: Syst em malfunction!. Ifm appears
after sw itching the ignition on or while d riv in g
and the
[I] i ndic ator ligh t in the i nstru men t clus­
te r blinks for approx imately one minute and then
stays on, the re is system ma lf u nction . Try to
store the co rrect tire pressures
r::!;> page 190 . If
the indicator light does turn off or turns on again
after a short period of time, drive to an author­
ized Audi dealer or author ized Audi Se rvice Facili­
ty immediate ly to have the ma lfunction correct ­
ed.
_&. WARNING
- I f the tire p ressure in dicator appears in the
d isp lay, redu ce you r speed immedi ately and
a void any h ard stee ring or bra king m aneu­
vers . S to p as soon as poss ible and check the
tires an d their pressure .
~
189

00
00
......
"' ,....
"' ...... 0 0 :::,
00
Care and cleaning
General information
Regular, proper care helps to maintain your vehi ­
cle's value. It can a lso be a requirement when
submitting warranty claims for corrosion damage
and paint defects on the body.
The necessary care products can be obtained
from an authorized Audi dealer or authorized
Audi Service Facility . Read and follow the instruc­
tions for use on the packaging.
A WARNING
- Us ing clean ing and care products incorrectly
can be dangerous to your health.
- Always store clean ing and care products out
of reach of children to reduce the r isk of po i­
son ing .
@ For the sake of the environment
- Preferably purchase env ironmenta lly-friend­
l y cleaning products.
- Do not d ispose of leftover cleaning and care
products with household trash.
Car washes
T he longer that deposits remain on the vehicle,
the more the surface may be damaged. High
temperatures such as those caused by sunlight increase the damag ing effect.
Befor e washing, rinse
off heavy depos its with
p lenty of water.
S tubborn depos its such as bird droppings or tree
sap are best removed with plenty of water and a
microfiber cloth.
A lso, wash t he un derside of yo ur vehicle once
road sa lt stops being used for the season .
Pressure washers
When washing your ve hicle w ith a pressure wash­
e r, a lways fo llow the operating instructions pro­
vided wi th the p ressure washer. This is especially
i mportant in rega rd to the pressure and sp raying
d istance . Do not aim the spray directly at seals on
side windows, doors, the hood, the luggage com-
Ca re and cleaning
partment lid or the panorama glass roof* or at
tires, rubber hoses, insulating material, sensors *
o r camera lenses* . Keep a distance of at least 16
in
(40 cm).
Do not remove snow and ice with a pressure
washer.
Never use cone nozz les o r high press ure nozzles .
T he water temperatu re must not be above
140 °F
(60 °().
Automatic car washes
Spray off the vehicle before washing.
Make s ure that the windows and roo f* are closed
and the windshie ld wipers are
off . Follow instruc ­
tions from the car wash ope rator, especially if
there are accessories attached to your vehicle.
If possible, use car washes that do not have
brushes .
Washing by hand
Clean the ve hicl e starting from the top and wor k­
i ng down using a soft sponge o r cleaning br ush.
U se solven t-free cleaning produ cts.
Washing vehicles with matte finish paint by
hand
T o avo id damag ing the pa int w hen washi ng, fi rst
remove dust and large pa rticl es from you r vehi­
cle . Insects, grease spots and fingerprints are
best removed w ith a special cleaner for matte
finish paint.
Apply t he product using a microf iber cloth . To
avoid damaging the paint surface, do not use too
much pressure.
Rinse the ve hicl e thoroug hly w ith wate r. Then
cl ean usi ng a neutral shampoo and a soft micro­
fiber cloth .
Rinse the ve hicl e thorough ly aga in and let it air
dry. Remove any wate r residue using a chamois.
WARNING
-On ly wash the vehicle when the ign ition is
off and follow the instr uctions from the car
191

Care and cleaning
Component Situation Solution
Te xtil es
Deposits adhering to Vacuum cleaner
artifi cial le ather , the surface
Alcan tara Water-based depos- Absorbent cloth and mild soap
solutional
its such as coffee,
tea, blood, etc.
O il-based deposits Apply a mild soap solution a), blot away the dissolved oil o r
such as oil, make-up, dye, treat afterward with water, if necessary
etc.
Special deposits such Special sta ,in remover, blot with absorbent material, treat
as ink, na il polish, la- afterward with mild soap solution, if necessary al
tex paint, shoe pol-
ish, etc.
Natural leather Fresh stains Wool cloth with a m
ild soap solutional
Water-based depos- Fresh stains: absorbent cloth its such as coffee, dried sta ins: stain remover suitable fo r leather
tea, blood, etc.
Oil-based deposits Fresh stains: absorbent cloth and stain remover suitable for
such as oil, make-up, leather
etc. dried sta
ins: oil clean ing sp ray
Special deposits such Spot remover suitable for leather
as ink, nai l polish, la -
tex paint, shoe pol-
ish, etc.
Ca re Regularly apply cond itioning cream tha t protects from light
a nd penetr ates into the ma ter ial. Use spec ia lly-co lored con -
ditioning cream, i f necessary.
Carbon parts Deposits clean the same way as plastic parts
a) Mild soap sol ution: maxim um two tablesp oons of neutral soap in 1 quart (l liter) of water
_& WARNING
The windshie ld may not be trea ted with w a­
ter-repelling windshield coating agents. Un­
favorable conditions s uch as wetness, dark­
ness, or low sun can result in increased glare .
Wiper blade chatter is also possib le.
(D Note
- Headlights/tail light s
-Never clean headlights or ta il lights with a
dry cloth or sponge.
- Do not use any cleaning p roduct that con­
tains alcohol, because they cou ld cause
cracks to form.
- Wheels
194
-
- Never use any paint polish or other abra­
sive materials.
- Damage to the protect ive layer on the
rims such as stone chips or scratches must
be repaired immediately.
- Sensors /camera lenses
- N ever use wa rm or ho t wa ter to remove
snow or ice from the camera lens . This
could ca use the lens to crack .
- N eve r use abrasive cleaning m aterials or
a lcohol to clea n the camera lens . This
could cause scratches and c racks .
-Door windows
- Remove snow and ice on windows and ex-
terior mirrors with a plast ic scraper. To

a:,
a:,
...... N r--. N .-< 0 0 ::, a:,
Emergency assistance
General information
.. Park the vehicle as far as poss ible from moving
traffic in the event of a breakdown. In the event
of a flat tire, park the vehicle on a leve l surface .
It you are on a steep h ill, be especially careful.
.. Set the parking brake .
.. Switch the emergency flashe rs on .
.. Put on a reflective vest .
.. Set up the warn ing triang le, if available .
.. Have the passengers exi t the veh icle. They
sho uld move to a safe place, for example be­
hind a guard rail.
_& WARNING
Follow the steps given above. This is for your
protection and the for the safety of other d riv ­
ers.
_& WARNING
Improper use of the vehicle jack can cause se ­
rious personal injuries .
- Never use the screw driver hex head to
t ighten whee l bolts, since the bolts cannot
attain the necessary tighten ing torque if you
use the hex head, potentially causing an ac­
c ident .
- The factory-supplied jack is intended only
for your vehicle model. Under no circum­
stances should it be used to lift heavy
vehicles o r other loads; yo u ris k inju ring
yo urself.
- Never start the engine when the vehicle is
ra ised, which could cause a n accident.
- Support the veh icle secure ly with app ropr i­
a te s tan ds if wor k is to be performed under­
neath t he vehicle; otherwise, the re is a po­
tent ial ris k for i njur y.
- Never use the jack s upplied with yo ur Audi
on another vehicle, pa rtic ularly o n a heav ie r
one. The jack is only suitable for u se on the
vehicle it came wit h.
Emergen cy a ssis tanc e
Equipment
Vehicle tool kit
Fig. 151 Lu gg age compartmen t: cargo floo r cove r fo lded
u pwa rd
T he veh icle tool k it is located in the luggage com­
partment under the cargo floor cover.
.. Push on the p lastic handle and lift up the cargo
floor .
.. Open the cargo floor.
Completely retract the veh icle jack a rm before
stor ing the ve hicle jack*.
_& WARNING
- Never use the screw driver hex head to
tighten wheel bo lts, since the bolts cannot
attain the necessary tightening torque if yo u
use the hex head, potentially causing an ac­
cident.
- The factory-supp lied jack is intended only
for your ve hicle model. Under no circum­
stances shou ld it be used to lift heavy
veh icles or other loads; you risk injuring
yourse lf.
- Never start the engine when the ve hicle is
raised, which could cause an accident.
- Support the vehicle securely with appropri­
ate stands if wo rk is to be performed under­
neath the vehicle; otherwise, there is a po­
tential risk fo r injury .
@ Tips
The vehicle jack * in your vehicle is mainte­
nance-free.
197

Emerg ency assis ta nce
Folding chocks
Applies to: ve hicles w ith fol ding chocks
The folding chocks* are part of the vehicle tool
kit.
-- -,,,.
F ig. 152 Opening the fo lding chocks
• To use the folding chocks, lift up the support
plate (!)¢
fig. 152 and insert them using both
"tabs" into the slotted holes on the base plate
@ ¢_& .
A WARNING
-The folding chock will not work and can lose
its stability if the support plate "tabs" are
not securely fitted in the slots on the base
plate. If th is is the case, the vehicle could
start mov ing when changing a tire.
- Never use fo ld ing chocks that are damaged
o r that were not assembled cor rectly.
Replacing wheels
Before changing a wheel
Observe the following precautions for your own
and your passenger's safety when changing a
wheel.
• After you experience a tire failure, pull the car
well away from moving t raffic and try to reach
l ev el ground before you stop¢
page 197,
¢_& .
• All passengers shou ld leav e th e car and move
to a safe location (for instance, beh ind the
guardrail)
¢ _& .
• Engage the park in g br ake to prevent your vehi­
cle from roll ing unintentionally ¢_& .
• Move the selec to r l eve r to the P po sition.
198
• If you are towing a trai ler : unhitch the t railer
from your veh icle.
• Take the jac k
¢page 197 and the sp are tire
¢
page 203 out of the luggage compartment.
A WARNING
You or your passengers could be injured while
changing a wheel if you do not follow these
safety precaut ions:
- If you have a flat tire, move a safe distance
off the road . Turn off the eng ine, turn the
emergency f lashers on and use other warn­
ing dev ices to alert other motorists.
- Make sure that passengers wait in a safe
place away from the vehicle a nd well away
from the road and traff ic.
- To he lp prevent the veh icle from moving
suddenly and possib ly sl ipping off the jac k,
always fu lly set the par king b rake and block
the whee l diagonally opposite the wheel be­
ing changed with the folding chocks or oth ­
er objects. When one front whee l is lifted
off the ground, placing the Automat ic
Transmission in "P" (Park) w ill
not prevent
the vehicle from moving.
- Before you change a whee l, be sure the
ground is level and firm . If necessary, use a
sturdy board under the jack.
- Always store the vehicle too l kit, the jack
and the replaced tire in the luggage com­
partment
¢ page 105.
(D Note
If you are changing the wheel on a steep in­
cline, use the folding chock¢
page 198 to
block the opposite whee l to prevent the vehi­
cle from moving.
@ Tips
Obey all laws.

a:,
a:,
...... N r--. N .... 0 0 ::, a:,
Changing a wheel
When you change a wheel, follow the sequence
described below step-by-step and in exactly that
order.
1. Remove the deco rative wheel co ve r* or the
whee l bolt cap s*. For more deta ils see also
c:> page 199.
2. Loosen the whee l bolt s c:> page 200.
3. Lo cate the proper mounting point for the
jack and align the jack below tha t point
<::> page 200.
4. Lift the car with the jack c:> page 200 .
5. Remove the wheel with the fl at tire and then
install the
s pare t ire c:> page 201 .
6. Tighten all wheel bolts lightly.
7 .
Low er the veh icle w ith the jack.
8 . Use the wheel bolt wrench and
firmly tighten
all wheel bolts in a crisscross pattern
c:> page 200.
9 . Replace the decorative wheel cover* o r the
whe el bolt cap s*.
_& WARNING
Always read and fo llow all WARNINGS and in­
formation
c:> .&. in Raising the vehicle on
page
201 and c:> page 202.
After changing a wheel
A wheel change is not complete without the do­
ing the following .
.. Always store the vehicle tool k it, the jack* and
the replaced t ire in the luggage compartmen t
c:>page 105.
.. Ch eck the tire pre ss ure of the spare tir e as soon
as possib le.
.. As soon as possible , have the
tighten ing tor ­
qu es
on all wheel bolts checked with a torque
wrench . The correct tightening torque is
105 ft lbs (140 Nm) .
.. Have the flat tire
replaced as soon as possible.
@ Tips
- If you notice that the wheel bolts are cor­
roded and diffic ult to turn wh ile changing a
Em ergen cy a ssis tanc e
tire, they shou ld be replaced before you
check the tightening torque .
- Drive at reduced speed until yo u have the
tightening torques checked.
Removing the wheel covers/bolt caps
Fig . 153 Cha ng in g a w hee l: r emov ing t he w hee l cover
Fi g. 1 54 Cha ng in g a whee l: remov ing the w hee l bol t cap s
Wheel cover*
.. Insert the hoo k provided w ith the vehicle tool
ki t in the hole in the hub
<::> fig . 153.
.. Pull off the decorati ve wheel cover .
Wheel bolt caps*
.. Push the plast ic clip provided with the vehicle
too l kit over the wheel bolt cap until it engages
c:> fig. 154 .
.. Pull on the pla sti c clip to remove the cap .
199

Emergency assistance
Loosening and tightening the wheel bolts
The wheel bolts must be loosened before raising
the vehicle.
Fig. 1 55 Changing a w heel : loosening the w hee l bo lts
Loosening
• Inst all the wheel bolt wrench ove r th e whee l
bolt and push it down as far as i t will go.
• Take tight hold of the
end of the wrench handle
and turn t he whee l bolts
counter-clockwise
about one single turn in the d irection of arrow
q fig . 155.
Tightening
• Install the wheel bolt wrench over the whee l
bolt and push it down as far as it will go.
• Take tight hold of the
end of the wrench handle
and turn each whee l bolt
clockw ise until it is
seated.
A WARNING
- Do not use force or hurry when changing a
wheel· you can ca use the vehicle to sl ip off
t h e jack and cause s erious pe rsonal injur ies.
- Do not loosen the whee l bolts mo re than
one turn
before you ra ise th e vehicle with
t h e ja ck .· You risk an i njur y.
(O} Tips
-Neve r use the he xagonal socket i n the han­
dle of the screwd river to loosen or tighten
th e w heel bo lts.
- If a wh ee l bolt is very t ight, you may fi nd it
eas ier to loosen by carefully push ing down
on th e end of th e wh eel bo lt wren ch wi th
one
fo ot on ly. As you do so, hold on to t he
200
car to keep yo ur ba lance and ta ke c are not
to slip.
Raising the vehicle
T he vehicle must be lifted wit h the jack first be ­
fore the wheel can be removed .
Fig. 156 S ill pa nels: mark in gs
Fig . 157 S ill : pos it io nin g the ve hicle jack
The location of the jack po int is indicated by an
i ndenta tion o n the underside of the veh icle
q fig . 15 6.
• Activate the parking brake to prevent the vehi­
cle from rolling uninte ntionally .
• Mov e the se lector lever to the P pos it ion .
• Find the
marking (imp rint) on the s ill that is
nea res t the w heel th at will be ch anged
¢ fig. 156 . Beh ind t he marking, there is a lift­
ing point on t he sill fo r the ve hicle jack .
• Tur n the
vehicle jack located un der the liftin g
point o n the sill to raise the jack until the jaw
¢ fig . 157 @covers the notch on the veh icle
¢ ,& , ¢(D .
• Align the vehicle jack so the jaw@ cove rs the
no tch and the base pla te ® is fla t on t he f loor .
Th e base p late @ must be
vertical unde r the
lif ting poin t@ . ..,_

a:,
a:,
...... N r-,. N
"" 0 0 ::, a:,
.. Install the rod on the vehicle jack: Insert the
rod into the opening on the handwheel. Turn
the rod left or r ight to secure it.
.. Cont inue raising the jack with the rod until the
wheel lifts off the ground slightly.
Position the vehicle jack
onl y under the designat­
ed lifting points on the sill
c:::> fig. 156. There is ex­
actly
one location for each wheel. The jack must
not be pos itioned at any other location
c:::> .&.,
c:::> CD.
Soft grou nd under the jack can cause the vehicle
to slip off the jack. Always place the jack on firm
ground . Use a flat, stable support if necessary.
Use a non-slip surface such as a rubber mat on a
s lipper y surfa ce such as tile .
_& WARNING
-
-Yo u or your passengers could be injured
wh ile chang ing a whee l if yo u do not follow
these safety precau tions:
- Position the veh icle jack only at the desig­
nated lifting points and align the jack.
Otherw ise, the vehicle jack cou ld slip and
cause an injury if it does not have suffi­
cient hold on the vehicle.
- Use on ly the jack* supplied with your vehi­
cle to raise the vehicle.
If yo u use a jack
from a d ifferent vehicle, your veh icle may
slip off the jack -ris k of injury!
- Do not use the jack* supp lied with your ve­
h icle to ra ise other veh icles, as these may
slip off the jack -ris k of injury!
- A soft or unstable s urface under the jack
may cause the vehicle to s lip off the jac k.
Always p rovide a firm base fo r the jack on
the ground . If necessary, use a sturdy
board underthejack .
- On hard, sl ippery surfa ce (such as tiles)
use a rubbe r mat or similar to prevent the
jack from slipp ing.
- T o help prevent injury to you rself and yo ur
passenge rs:
- Do not ra ise the vehicle unt il you are sure
the jack is securely engaged .
- Passengers must not remain in the vehicle
when it is jacked up.
Em ergen cy a ssis tanc e
-Make sure that passengers wait in a safe
place away from the vehicle and well away
from the road and traffic .
- Make sure jack position is correct, adjust
as necessary and then continue to raise
the jack.
- If work has to be done under the veh icle,
ensure that it is safely supported on suita­
ble stands -risk of injury!
- Never start the engine when the vehicle is
on the jack -risk of acc ident!
(D Note
Do not lift the ve hicle by the s ill. Pos ition the
vehicle jack only at the des ignated lifting
po ints on the sill. Otherw ise, your veh icle will
be damaged.
Taking the wheel off/installing the spare
tire
Follow these instructions step-by-step for chang ­
ing the wheel.
F ig . 1 58 Chang ing a w hee l: us ing the hexagona l socket
(with the blade removed) to turn the bolts
Fig. 159 Changi ng a whee l: alig nment p in i nside the top
h ole
201

Emergency assistance
After you have loosened a ll wheel bo lts and
raised the vehicle off the ground, remove and re­
p lace the whee l as fo llows:
Removing the wheel
.,. Remove the topmost wheel bol t comp letely
with the
he xagonal socket in t he screwd river
hand le (vehicle tool kit)
¢ fig. 158 and set it
aside on a
clean s ur face.
.,. Screw the threaded end of the
alignment pin
from the tool k it hand-tight into the empty bolt
hole¢
fig. 159 .
.,. The n remove the other wheel bolts as described
above.
.,. Take off the wheel leav ing the a lignment pin in
the bo lt hole ¢ 0.
Putting on the spare tire
.,. Push the spare tire over the alig nment pin
¢ (D .
.,. Screw on the wheel bo lts and tighten them
slightly using the hex agonal socke t.
.,. Remove the a lignment pi n an d in se rt an d tight­
en t he rem aining wheel bol t slightly like the
res t.
.,. Turn the jack handle counter-clockwise to lower
the ve hicle until the jack is fully re leased .
.,. Use the wheel bolt wrench to tighten all wheel
bolts firmly. Tighten them
in a crisscross pat­
tern,
from one bol t to the (app roximately) op­
pos ite one, to keep the whee l cente red .
.,. Perfo rm the steps req uire d afte r changing the
whee l ¢
page 199, After changing a wheel.
&, WARNING
Do not us e the he xagon al so cke t in t he screw ­
dr iver han dle to tig hten the wheel bol ts . I t is
not poss ib le to tighten t he bo lts to the re­
quired torque usin g t he he xagonal socket -
r is k of accident!
(D Note
W hen removi ng or inst alling the whee l, the
r im cou ld hit the brake roto r and dama ge t he
rotor . Work ca ref ull y and have a seco nd per­
son to help you.
202
(D Tips
- When mo unting tires with unidirectional
tread design
make sure the trea d pattern is
pointed the right way¢
page 202.
-The wheel bolts s hould be clean an d easy to
t u rn. Check fo r dirt and corrosion on the
matin g surfaces of both the wheel and the
hub. Remove all dirt from these s urfaces be­
fore remounting the whee l.
Tires with unidirectional tread design
Tires with unidirectional tread design mus t be
mounted with their tread pattern pointed in the
right direction .
Using a spare tire with a tread pattern
intended for use in a specific direction
When using a s pare tire w ith a t read patter n in ­
te nded for use in a specif ic direct ion, please note
t h e followi ng :
- The d irection of rotation is marked by an
arrow
on the side of the tire .
-If the spare tire has to be installed in the incor­
rect direction, use the spare tire on ly tempora­
r il y since the tire will not be able to ac hieve its
op timum performa nce characterist ics w ith re­
gard to aquap la ni ng, no ise a nd wear.
- W e recommend that you pay part icu lar atten­
t ion to th is fact d urin g we t wea ther an d that
you a djust your spee d to matc h road cond i­
tion s.
- Rep lace the flat tire w it h a new one an d have it
inst alled o n your ve hicle as soon as possib le to
res tore the h andlin g advan tage s of a unidir ec­
tional tire .
Notes on wheel changing
Please read t he informat ion ¢ pa ge 17 8, New
tires or wheels
if yo u ar e go ing to use a spare tire
which is d ifferent from the t ires o n your ve hicle.
A ft er yo u ch an ge a tire:
- Check the tire pressure on the spare immedi-
ately after installation. .,.