wheel AUDI Q7 2018 Owner´s Manual

Wheels
are listed on the safety compli­
ance sticker label located on the
driver's side B-pillar.
A WARNING ,-= · -
Overloading a vehicle can cause
loss of vehicle control, a crash
or other accident, serious per­
sonal injury, and even death .
-Carrying more weight than your vehicle was designed to carry will prevent the vehicle
from handling properly and i ncrease the risk of the loss of
vehicle control.
-The brakes on a veh icle that
has been overloaded may not
be able to stop the vehicle
within a safe distance.
-Tires on a vehicle that has been overloaded can fail sud­
denly, including a b lowout and
sudden deflation, causing loss
of contro l and a crash.
-Always make sure that the to­ tal load being transported -i nc luding the weight of a tra il­
er hitch and the tongue
weight of a loaded trailer­
does not make the vehicle
h eavier than the vehicle's
Gross Vehicle Weight Rating.
3 44
Determining correct load
limit
Use the example below to calcu­
late the tota l weight of the pas­
sengers and luggage or other
things that you plan to transport
so that you can make sure that
your vehicle will not be over load ­
ed.
Steps for Determining Correct Load Limit
1 . Locate the statement " TH E
COMBIN ED WE IGH T OF OCC U­
PANTS AND CARGO SHOU LD
NEVER EXCEED XXX KG OR XXX
LBS" on your vehic le's placard
(tire inflation pressure label)
¢ page 340, fig . 272 .
2. Determine the combined
weight of the drive r and pas­
sengers that will be riding in
your vehicle.
3. Subtract the combined weight
of the driver and passengers
from
"XXX" kilograms or "XXX"
pounds shown on the stick­
er ¢
page 340, fig. 272 .
4. The resu lting figure equa ls the
available amount of cargo and
luggage load capacity . For ex­
ample, if the "XXX" amount
eq uals 1400 lbs. and there will~

Cl a:, ...... N
" N ...... 0
0
::r '<t
be five 150 lb s. pa ssenge rs in
y o ur vehi cle, th e am ount of
ava ilable cargo a nd lu ggage
l oa d cap acity is 650 lb s.
(1400-750 (5
X 150) = 650
lb s.)
5 . Determine th e combined
w eight of lu gga ge and cargo
bein g load ed on the vehicle .
Th at w eight m ay not sa fel y
ex ­
ceed th e av ail able car go and
lu ggage l oad capa city ca lc ul at­
e d in St ep 4 .
6 . If your vehicle will b e to wing a
tr ail e r, load from your tr ailer
will b e tran sferr ed to your
v e­
hi cle . C on sul t thi s manual t o
dete rmin e how this re du ces
th e av ailabl e c argo and lug­
ga ge load cap acity o f your vehi­
c le.
.,. Che ck th e tir e s idewall
(c:::> p ag e 33 1, fig. 269) to det er­
min e the de signated load r ating
for a specific tire.
Wheel bolts and rims
Wheel bolts
Wheel bolts must be clean and loosen/t ighten
eas ily .
Rims
Rims w ith a bolted rim ring* o r with bolted wheel
cove rs* consis t of multip le pieces. These compo­
nents were bolted together using specia l bolts
Wheels
and a spec ia l proced ure. Yo u must not repair or
disass emb le them <::>
.&..
A WARNING
--
Wheel bo lts that are tightened or repaired in­
correct ly can become loose and resu lt in loss
of vehicle contro l, wh ich increases the risk of
an accident . For the cor rect tighten ing specifi­
cation, see <::>
page 362, Finishing .
-Always keep the wheel bolts and the
threads in the wheel h ub clean and free of
g rease .
- Only use wheel bolts that fit the rim .
- Always have damaged rims repaired by an
author ized Audi dealer or author ized Audi
Serv ice Facility . Never repair or disassemb le
rims yo urself, because th is increases the r isk
of an acc ident.
Winter tires
Winter tires sign ifican tly imp rove the vehi cle's
handling when dr iv ing in winter conditions . B e­
ca use of their const ruct ion (w idth, compou nd,
tread pattern), summer tires provide less trac ­
tion on ice and snow .
.,. Use winter tires on all four wheels.
.,. On ly use winter tires that a re app roved fo r yo ur
ve hicle.
.,. Please not e that th e maximum permitted
speed may be lower with winter ti res
c:> &. in
General information on page 330 .
An author­
ized Aud i dealer or authori zed Aud i Serv ice Fa­
cility can inform you about t he maximum per ­
m itted speed for your tires .
.,. Check the tire p ressure afte r insta lling wheels
<::> page 340 .
The effectiveness of w inter tires is reduced great­
ly when t he tread is wo rn down to a depth of
0.16 in (4 mm). The cha racter istics of w inte r
t ir es also decrease g reatly as the t ire ages, re ­
gard less o f th e rem aining t read.
@ For the sake of the environment
Reinstall summer tires at the app ropr iate
time , beca use they prov ide bette r handling
when roa ds are free o f snow and ice. Summer ..,.
345

Wheels
tires cause less road noise, tire wear and fuel
consumption.
(D Tips
You can also use all season tires instead of
winter tires. Please note that in some coun­
tries where winter tires are required, only
winter tires with the
& symbol may be per­
mitted.
Snow chains
Snow chains not only improve the driving in win­
ter road conditions, but also the braking .
~ Only install snow chains on the front wheels.
~ Check and correct the seating of the snow
chains after driving a few feet, if necessary . Fol­
low the instructions from the manufacturer.
~ Note the maximum speed of 30 mph (SO km/
h). Note the local regulations.
Use of snow chains is only permitted with certain
rim/tire combinations due to technical reasons.
Check with an authorized Audi dealer or author­
ized Audi Service Facility to see if you may use
snow chains.
Use
fine-mesh snow chains . They must not add
more than 0 .53 in (13.5 mm) in height, including
the chain lock.
You must remove the snow chains on roads with ­
out snow. Otherwise, you could impair driving
ability and damage the tires.
.&_ WARNING
Using incorrect snow chains or installing snow
chains incorrectly can result in loss of vehicle
control, which increases the risk of an acci­
dent.
(LlJ) Note
- Snow chains can damage the rims/wheel
covers* if the chains come into direct con­
tact with them. Remove the wheel covers*
first. Use coated snow chains.
- Do not install and use snow chains if there is
a malfunction in the air suspension*, be­
cause the vehicle height will be
very low. If
346
you drive with snow chains anyway, the
wheel housings and other vehicle compo­ nents can be severely damaged.
(D Tips
When using snow chains, it may be useful to
switch the offroad mode on
r=> page 143.
Low-profile tires
Applies to: vehicles with low-profile tires
Compared to other tire/rim combinations, low­
profile tires offer a wider tread surface and a
larger rim diameter with shorter tire sidewalls.
This results in an agile driving style. However, it
may reduce the level of comfort and increase
road noise when driving on roads in poor condi­
tion.
Low -profile tires can become damaged more
quickly than standard tires when driving
over
large bumps, potholes, manhole covers, and
curbs . Therefore, it is particularly important to
maintain the correct tire pressure
r=.> page 340.
To reduce the risk of damage to the tires and
rims, drive
very carefully on poor roads.
Check your wheels regularly every 2,000 mi
(3,000 km) for damage . For example, check for
bulges/cracks on the tires or deformations/
cracks on the rims.
After a heavy impact or damage, have the tires
and rims inspected or replaced immediately by
an authorized Audi dealer or authorized Audi
Service Facility.
Low-profile tires can wear out faster than stand­
ard tires .
Uniform tire quality grading
- Tread wear
- Traction AA ABC
- Temperature ABC
Quality grades can be found where applicable on
the tire side wall between tread shoulder and maximum section width
r=.> page 331, fig. 269.

Cl a:, ...... N
" N ...... 0
0
::r '<t
For example: Tread wear 200, Traction AA, Tem­
perature
A.
All passenger car tires must conform to Federal
Safety Requirements in addition to these grades.
Tread wear
The tread wear grade is a comparative rating
based on the wear rate of the tire when tested
under controlled conditions on a specified gov­
ernment test course.
For example, a tire graded 150 would wear one
and one ha lf (1 1/2) times as well on the govern­
ment course as a tire graded 100.
The relative performance of tires depends upon
the actual conditions of their use, however, and
may depart significant ly from the norm due to
variations in driving habits, service practices and
differences in road characteristics and climate.
Traction
The traction grades, from highest to lowest, are
AA, A, B and
C. Those grades represent the tire's
ability to stop on wet pavement as measured un­
der controlled conditions on specified govern­
ment test surfaces of asphalt and concrete . A tire
marked C may have poor traction performance
¢ &, .
Temperature
The temperature grades are A (the highest), B,
and C, representing the tire's resistance to the
generation of heat and its ability to dissipate
heat when tested under controlled conditions on
a specified indoor laboratory test wheel.
Sustained high temperature can cause the mate­
rial of the tire to degenerate and reduce tire life,
and excessive temperature can lead to sudden
tire failure¢ &,.
The grade C corresponds to a level of perform­
ance which all passenger car tires must meet un­
der the Federal Motor Vehicle Safety Standard
No. 109. Grades Band A represent higher levels
of performance on the laboratory test wheel than
the minimum required by law.
Wheels
A WARNING
--
The traction grade assigned to this tire is
based on straight-ahead braking traction
tests, and does not include acceleration, cor­
nering, hydroplaning or peak traction charac­
teristics.
A WARNING
The temperature grade for this tire is estab­
lished for a tire that is properly inflated and
not overloaded. Excessive speed, underinfla­
tion, or excessive loading, either separately or
in combination, can cause heat buildup and
possible tire failure.
A WARNING
-
--
Temperature grades apply to tires that are
properly inflated and not over or underinflat­
ed.
Tire pressure monitoring system
ill
General notes
Each tire, including the spare (if provided),
should be checked monthly when cold and inflat­
ed to the inflation pressure recommended by the
vehicle manufacturer on the vehicle placard or
tire inflation pressure label. (If your vehicle has
tires of a different size than the size ind icated on
the vehicle placard or tire inflation pressure la­
bel, you should determine the proper tire infla­
tion pressure for those tires).
As an added safety feature, your vehicle has been
equipped with a tire pressure monitoring system
(TPMS) that illuminates a low tire pressure tell­
tale when one or more of your tires is significant­ ly under -inflated. Accordingly, when the low tire
pressure telltale illuminates, you should stop and
check your tires as soon as possible, and inflate
them to the proper pressure. Driving on a signifi­ cantly under-inflated tire causes the tire to over­
heat and can lead to tire failure . Under-inflation
also reduces fue l efficiency and tire tread life,
and may affect the vehicle 's handling and stop-
ping ability. .,.
347

Wheels
Please note that the TPMS is not a substitute for
proper tire maintenance, and it is the driver's re­
sponsibility to maintain correct tire pressure,
even if under-inflation has not reached the level
to trigger illumination of the TPMS low tire pres­
sure telltale.
Your vehicle has also been equipped with a TPMS
malfunction indicator to indicate when the sys­
tem is not operating properly. The TPMS mal­
function indicator is combined with the low tire pressure telltale. When the system detects a
malfunction, the telltale will flash for approxi­
mately one minute and then remain continuously
illuminated. This sequence will continue upon
subsequent vehicle start-ups as long as the mal­
function exists.
When the malfunction indicator is illuminated,
the system may not be able to detect or signal
low tire pressure as intended. TPMS malfunctions
may occur for a variety of reasons, including the
installation of replacement or alternate tires or
wheels on the vehicle that prevent the TPMS
from functioning properly . Always check the
TPMS malfunction telltale after replacing one or
more tires or wheels on your vehicle to ensure
that the replacement or alternate tires and
wheels allow the TPMS to continue to function
properly.
If the tire pressure monitoring indicator
appears
Applies to: vehicles with Tire Pressure Monitoring System in­
dic ato r
The tire pressure indicator in the instrument
cluster informs you if the tire pressure is too low
or if there is a system malfunction.
Using the ABS sensors, the tire pressure monitor ­
ing system compares the tire tread circumfer­
ence and vibration characteristics of the individu­
al tires . If the pressure changes in one or more
tires, this is indicated in the instrument cluster
display with an indicator light
RI] and a message.
If only one tire is affected , the location of that
tire will be indicated.
The tire pressures must be stored in the Infotain­
ment system again each time the pressures
348
change (switching between partial and full load
pressure) or after changing or replacing a tire on
your vehicle ~
page 349. The tire pressure moni­
toring system only monitors the tire pressure you have stored. Refer to the tire pressure label for
the recommended tire pressure for your vehicle
~ page 340, fig . 272.
Tire tread circumference and vibration character­
istics can change and cause a tire pressure warn­
ing if:
- the tire pressure in one or more tires is too low
- the tires have structural damage
- the tire was replaced or the tire pressure was
changed and it was not stored
~ page 349
- tires that are only partially used are replaced
with new tires
Indicator lights
RI] -loss of pressure in at least one tire~,& .
Check the tires and replace or repair if necessary.
Check/correct the pressures of all four tires and
store the pressure again in the Infotainment sys­
tem
~ page 349.
m (Tire Pressure Monitoring System) Tire
pressure: malfunction! See owner's manual.
If
m appears after switching the ignition on or
while driving and the
RI] indicator light in the in­
strument cluster blinks for approximately one
minute and then stays on, there is system mal­
function. Try to store the correct tire pressures
~ page 349. In some cases, you must drive for
several minutes after storing the pressures until
the indicator light turns off . If the indicator light
does turn off or turns on again after a short peri­
od of time, drive to an authorized Audi dealer or
authorized Audi Service Facility immediately to
have the malfunction corrected.
& WARNING
- If the tire pressure indicator appears in the
display, reduce your speed immediately and
avoid any hard steering or braking maneu­
vers. Stop as soon as possible and check the
tires and their pressure.

-The driver is responsib le for maintaining the
correct tire pressure. You must c heck the
t ire pressure regu larly.
- Under certa in conditions (s uch as a sporty
dr iv ing style, winter cond itions o r unpaved
roads), the tire p ressure monitoring system
indicator may be de layed .
(D Tips
-The t ire press ure monitoring system can al­
so stop work ing when there is an ESC mal­
funct ion.
- Using snow chains may result in a system
malfunction.
- The t ire press ure monitoring system in your
A udi was calib rated with "A udi Orig inal
Tires"
<=)page 337. Using these t ires is rec­
omme nded .
Storing tire pressures
Applies to: vehicles with Tire Pressure Monitoring System in­
dicator
If the tire pressure changes or a tire is replaced,
it must be confirmed in the Infotainment sys ­
tem.
~ Make s ure before storing that the tire pressures
of a ll fou r tires meet the specified values and
are adapted to the load
Q page 340 .
~ Switch the ign ition on.
~ Se lect in the Infotainment system: ! MENUI but­
ton
> Vehicle > Service & checks > Tire pres­
sure monitoring > Store tire pressur e> Yes,
store now .
(D Tips
Do not store the tire press ures if snow chains
are insta lled.
Run-flat ti res
Applies to: vehicles with run-flat tires
A run-flat tire helps to maintain vehicle mobility
when there is a loss of pressure .
Cl ~ Run-flat t ires have re inforced sidewalls that pro-
~ tect the t i re if there is a loss of press ure. N ,-1 0
0
::r '<t
Wheels
If the t ire pressure monitoring system indicates a
l oss of pressure in one or severa l tires, yo u can
contin ue driving on run -flat tires fo r at least 20
miles (30 km). Drive to an authorized Audi dealer
or authorized Aud i Serv ice Facility immediately to
have the problem corrected .
Continuing to drive on run-flat tires is n o
longer possible if
- there is visible damage to the tires, such as
cracks in the sidewalls .
- strong vibrat ions are felt w hile driving, or the
tire beg ins to smoke due to a strong build-up of
heat .
- the t ire was heavi ly damaged, for example in an
accident There is a r isk that parts of the tire
tread will detach and damage important ve hi­
cle components .
- the E lectron ic Stab ilizat ion Control (ESC) is not
work ing or is cont inuously r unning .
- the t ire pressure monitoring system is not
work ing .
If it is no longer poss ible to continue driving de­
spite hav ing run-flat tires, see an author ized Audi
dealer or author ized Audi Service Fac ility for as­
s istance.
A WARNING
-
R un-f lat t ires may only be used on vehicles
that we re equipped with them at the fa ctory.
- The vehicle must have suspens ion designed
for run-flat tires and a facto ry-installed tire
p ress ure mo nitor ing syste m.
- I nco rrect use of r un-f lat t ires can lead to ve­
h icl e damage o r accidents. Contact an au­
thor ized A udi dealer or au thori zed A udi
Serv ice Facili ty to lear n if r un-f la t tir es may
be used on you r vehicle an d if so, which
ones.
- If r un-fla t ti re s are used, they m ust be in ­
stalled on all fo ur whee ls. Mix ing ti re types
is not permitted.
- If yo u have to drive when the tire press ure is
too low or there is no tire press ure, note the
following : .,..
349

Wheels
-Do not dr ive faste r than 50 mph (80 km/
h) because this increases the risk of an ac­
cident. Observe any laws specific to the
country where yo u are driv ing.
- Avoid full-th rottle accele ration, heavy
braking, and fast cornering, because this
increases the r isk of an accident .
- The vehicle may become more difficult to
control.
- See an autho rized Aud i deale r or a uthor­
ized Audi Service Fac ility for assistance if
the t ire is too heavily damaged.
- Have the faulty tires replaced and the rims
checked fo r damage by an author ized A udi
dealer or author ized Audi Service Facil ity.
- The driver is responsib le for the vehicle, fo r
correcting the t ire pressure and for rep lac­
ing faulty parts. Therefore, always adjus t
yo ur driv ing to the g iven s ituation .
(D Tips
-Audi Orig inal run-flat tires can be identified
by the "AOE" labeling on the tire sidewall.
- You can use the tire mob ility k it*
c:> page 357 on run-flat ti res.
350

Care and cl eaning
wash operator to reduce the risk of acci­
dents.
- To reduce the risk of cuts, protect yourself
from sharp metal components when was h­
ing the underbody or the inside of the wheel
housings .
- After washing the vehicle, the braking effect may be delayed due to mo isture on the
brake rotors or ice in the winter . This in­
creases the risk of an acc ident . The brakes
must be d ried first w it h a few careful b rake
applications.
@ Note
- If you wash the ve hicle in an automatic car
wash, you must fold the exterior m irrors in
to reduce the risk of damage to the mirrors .
P ower folding exte rior m irrors* must o nly
be fo lded in and out using the powe r folding
f u nct io n.
- To reduce t he risk of damage to the rims
and t ires , compare the width be tween the
whee ls on your ve hicl e w it h t he distance be ­
tween the g uide rai ls in the car wash .
- To reduce t he risk of damage, compare the
height and width o f you r vehicle with the heig
ht and w idth of the inside o f the car
was h.
- T o red uce the risk of pa in t damage, do not
was h the vehicle in direct sun light .
- T o red uce the risk of d amage to the s urf ace,
do not use insect removing sponges, k itchen
sponges or similar items .
- Matte finish painted vehicle components:
- To reduce the r isk of damage to the sur-
face, do not use polis hing agents or hard
wax .
- Never use protective wax. It can destroy
the matte finish effect .
- Do not place any stickers or magnet ic
signs on vehicle parts painted with matte
finish paint . The paint cou ld be damaged
when the stickers or magnets are re­
moved .
@ For the sake of the environment
Only wash the ve hicle in facilities spec ia lly de­
s igned for that pu rpose . This will reduce the
r isk of dirty wate r contaminated with o il from
ente ring the sewe r system.
Cleaning and care information
W hen clea ning and ca ring for ind ividua l vehicle
components, refer to the fo llowing tables . The
information contained there is simply recom­
m endations. Fo r qu estions or for compon ents t
h at are not listed, cons ult an autho rized Aud i
dealer or authorized A udi Service Fac ility. Also
fo llow the information fo und inc:>.&. .
Ext erior cleaning
Component Situation Solution
Windshield wiper
Deposits soft cloth with glass cleane r, c:> page 51
blades
Headlights /
Deposits Soft sponge with
a m ild soap solution a)
tail light s
S ensors /
Deposits Sensors: soft cloth with solvent -free cleaning solut ion
camera lenses Camera lenses: soft cloth w it h alcohol-free cleaning solu-
tion
Snow/ic e Hand brush/solv ent-free de -icing spray
Wheels Road salt Water
Brake dust Acid-free special cleaning solution
352

Care and cl eaning
Component Situation Solution
Tex tile s
Deposits adhering to Vacuum cleaner
art ifici al l eat her, the surface
A lca ntara Water -based deposits Absorbent cloth and mild soap
solutiona>
such as coffee, tea, blood, etc.
O il-based deposits Apply a m ild soap solution a), blot away the dissolved oil or
such as oil , make-up, dye, treat afterward with water, if necessary
etc.
Special deposits such Special stain remover, blot with absorbent material, treat
as ink, na il polish, la- afterward with mild soap solution, if necessary a)
tex paint, shoe pol-
ish, etc.
Natural leathe r Fresh stains Cotton cloth
with a mild soap solutiona >
Water-based deposits Fresh stairns : absorbent cloth
such as coffee, tea, dried stains: stain remover suitable for leather
blood, etc.
Oil -based deposits Fresh stairns : absorbent cloth and stain remover suitable
such as oil, make-up, for leather
etc. dried stains: oil cleaning spray
Special deposits such Spot remover suitab le for leather
as ink, nai l polish, la -
tex paint, shoe pol-
ish, etc.
Care Regula rly apply cond it ion ing cream that p rotects from
lig ht and penetrates into the material. Use specia lly-co l-
ored conditioning cream, if necessary .
Carbon part s Deposits clean the same way as plastic parts
al Mild soap solution: maximum two tablespoons of neutral soap in 1 quart (1 liter) of water
_& WARNING
The windsh ie ld may not be treated wi th wa­
ter-repelling windshield coating agents. Un ­
favorable conditions such as wetness, dark ­
ness, or low sun can result in increased glare.
Wiper blade chatter is also possible.
@ Note
-Headlight s/tail light s
-Never clean headlights or tail lights with a
dry cloth or sponge.
- Do not use any cleaning product that con­
tains alcohol, because they could cause
cracks to form .
-Wheel s
354
-
- Never use any paint polish or other abra­
sive materials.
- Damage to the protect ive layer on the
rims such as stone chips or scratches must
be repaired immediately.
- Cam era lens es
- Neve r use wa rm or hot water to remove
snow or ice from the came ra lens . This
could cause the lens to crack .
- Neve r use ab rasive cleaning m aterials or
a lcohol to clean the camera lens . This
could cause scratches and cracks .
-Door wind ow s
- Remove snow and ice on windows and ex-
terior mirrors with a plast ic scraper. To

Cl a:, ...... N
" N ,-1 0
0
::r '<t
-If a tire pressure of 29 psi (200 kPA) cannot
reached after inflating for 6 minutes, then
the tire is too severely damaged. Do not
continue driving .
- If the t ire cannot be repaired with the tire
sealant, see an authorized Audi dealer or au­
thorized Aud i Serv ice Facility for ass istance .
(D Tips
Do not operate the compressor for more than
six m inutes continuously, or it can overheat.
Once the compressor has cooled, you ca n con­
tinue to use it .
Completing
"'Adhere the sticker that says "max . SO mph
(max. 80 km/h)" that is p rovided w it h the t ire
mobility kit within the dr ive r's fie ld of vision.
"' Stop the vehicle afte r driving for about 10 m i­
nutes and check the tire pressure .
"' If the tire pressure is lower than 19 psi ( 130
kPA), then the tire is too severely damaged. Do
not cont inue driving.
A WARNING
Pay attent ion to the following after repair ing
the t ire :
- Do not drive faster than SO mph (80 km/h).
- Avoid hard acceleration, brak ing sharply,
and fast cornering.
- The vehicle may become more difficu lt to
contro l.
- If the tire is too severely damaged, see an
authorized Audi dealer or authorized Audi
Service Facility for assistance.
@ For the sake of the environment
You can give the used tire sealant bottle to an
authorized Audi dealer or authorized Audi
Service Facility for disposal.
(D Tips
Remember to obtain a new bottle of sea lant
from an authorized Audi dea ler or authorized
Audi Service Facility after repairing a tire.
Em ergenc y ass is tanc e
Replacing a wheel
Preparation
You must complete the preparation before
changing a tire .
"'Read and follow the impor tant safe ty precau-
tions
¢ page 357.
"'Set the park ing brake .
"' Select the "P" selector lever position .
"' When towing a tra iler : disconnect the trailer
from you r vehicle.
"' Lay out t he vehicle too l kit ¢
page 357 and the
spare tire.
"' Switch on wheel change mode* in the Infotain­
ment syst em:
!MENUI button> V ehicle > left
control button >
S erv ic e & ch ecks > Air s uspen­
s io n: w heel chang e.
"'Switch the ignit ion off.
The vehicle jack mod e* switches off automatica l­
ly at speeds above 6 mph ( 10 km/h).
A WARNING "---
When us ing the ve hicle jack" on a road with a
steep hill or offroad, you must take extra pre ­
cautions to prevent the vehicle from rolling .
Use su itable objects to block the front and
back of t he wheel t hat is diagonal from the
whee l with the flat t ire.
A WARNING
You o r yo ur passenge rs could be injured while
changing a whee l if you do no t follow these
safety precautions :
- I f yo u have a flat tire, move a safe dis tance
off the road. Turn off the eng ine, turn the
emergency flashers on and use other warn ­
ing devices to a lert other motorists.
- Make sure that passengers wait in a safe place away from the vehicle and well away
from the road and traff ic.
- To he lp prevent the vehicle from moving
suddenly and possib ly slipping off the jack*,
a lways f ully set the park ing brake and block
the front and back of the wheel diagonally
opposite the wheel being changed. When
one front wheel is lifted off the ground,
~
359