remove seats AUDI RS5 CABRIOLET 2013 Owners Manual

62 Seats and storage
close to this position as possible
¢page 64.
A WARNING
Never place any objects in the driver's foot­
well. An object could get into the pedal area and interfere with pedal function. In
case of sudden braking or an accident, you
would not be able to brake or accelerate .
Front passenger's seat
Always move the front passenger seat into
the rearmost position .
To avoid contact with the airbag while it is de­
ploying, do not sit any closer to the instru­
ment panel than necessary and always wear
the three-point safety belt provided adjusted correctly . We recommend that you adjust the
passenger's seat in the following manner:
• Bring the backrest up to an (almost) upright
position. Do not ride with the seat reclined .
• Applies to vehicles with adjustable head re­
straints: Adjust the head restraint so the up­
per edge is as even as possible with the top
of your head . If that is not possible, try to
adjust the head restraint so that it is as
close to this position as possible
¢ page 64.
• Place your feet on the floor in front of the
passenger's seat.
Front seats
Power seat adjustment
Fig. 68 Front seats: powe r seat adjustment
Controls
@ -Adjusting the lumbar support* : press the
button in the corresponding position ¢ .&, .
@ -Moving the seat up/down: press the but­
ton up/down ¢ .&, .
@ -Moving the seat forward/back : press the
button forward/back ¢.&, .
©-Adjusting the backrest angle: press the
button forward/back ¢.&. .
©-Raising/lowering * the head restraints:
press the button up/down¢.&. .
@ -Lengthening/shortening the upper thigh
support* : lift the handle. A spring moves the
front seat cushion forward ¢ .&. .
A WARNING
--
-Never adjust the driver's or front pas ­
senger's seat while the vehicle is moving.
If you do this while the vehicle is moving,
you will be out of position . Always adjust
the driver's or front passenger's seat
when the vehicle is not mov ing.
- Be careful when adjusting the seat
height . Check to see that no one is in the
way, or serious injury could result!
- Because the seats can be electrically ad­
justed with the ignition off or with the
ignition key removed, never leave chil­
dren unattended in the vehicle. Unsuper­
vised use of the electric seat adjust­
ments may cause serious injury.
- To reduce the risk of injury in the case of
sudden braking or accident, front pas ­
sengers must never ride in a moving ve­
hicle with the backrest reclined. Safety
belts and the airbag system only offer maximum protection when the backrest
is upright and the safety belts are prop­
erly positioned on the body. The more
the backrest is reclined, the greater the
risk of personal injury from an incorrect
seating position and improperly posi­
tioned safety belts.

Remote control key
Applies to vehicles: with seat memory
To assign the d river 's sea t settings to the re­
m ote cont ro l key when locking the vehicle, the
f u nction must be activ ated in the radio or
M MI*
.. Se lect :
I CAR I fu n ct io n but ton > Seat adjust ­
ment
> Driver's seat > Remote control key >
on .Or
.. Se lect:
~ I C - A- R~ I fu nction but ton > Car sy stem s*
co ntrol button > Vehicle settings > Seats >
Driver's seat > Remote control key > On .
@ Tips
If you do not want another driver's set­
tings to be assigned to the remote key,
sw itch off the memo ry function us ing t he
rad io or MMI* or the
!ON/OF F I button
¢page 65.
Memory buttons
Applies to vehicles: with seat memo ry
F ig. 7 3 Driver 's door: mem ory fu nct io n buttons
The memory buttons are located i n the driv­
er 's door .
Switching the memory function on/off
.. Pres s the I ON/OF F I butt on to swi tch the
memo ry function on/off . The wor d
OFF
lights up when the memory f unction is
switched off. Seat prof iles are not sto red .
Storing a seat profile
.. Press the ISET I button. W hen the word SET
ligh ts up, the memory is re ady to s tore se t­
t ings .
Seats and storage 65
.. Press a memory bu tto n dil or ~ brie fly. A
tone conf irms that the settings were stored .
Accessing a seat profile
.. If the driver's door is open, pre ss a memory
but ton.
.. If the d river 's door is closed, p ress and hold
the memo ry but ton unti l the seat adjus t­
ment is complete.
&_ WARNING
- For safety reas ons , the seat setting can
o nly be recalled when the vehicle is sta­
tionary -otherwise yo u risk havi ng a n ac­
cident.
- In an emergency the r ecall p roced ure ca n
be cancelled by pressing t he
IO N/O FF!
sw itch o r by ta pping the m emory bu t­
tons.
Ashtray
Fi g. 74 Ce nter console: ashtray
Opening/closing
.. To open t he ashtr ay, slide t he cover up
c:> fig. 74.
.. To close the ashtray , press dow n on the cov­
er .
Emptying the ashtray
.. To remove the in sert, s lide the l atch to the
r igh tc:>fig . 74-ar row -.
.. To ins ta ll th e insert, press it down i nto the
mou nt .

13 2 Safety belts
Important safety instructions about
safety belts
Safety belts must always be correctly posi­
tioned across the strongest bones of your
body.
,.. Always wear safety belts as illustrated and
described in this chapter.
,.. Make sure that your safety belts are always
ready for use and are not damaged.
,&. WARNING
Not wearing safety belts or wearing them
improperly increases the risk of serious
personal injury and death. Safety belts can
work only when used correctly .
- Always fasten your safety belts correctly
before driving
off and make sure all pas­
sengers are correctly restrained.
- For maximum protection, safety belts must always be positioned properly on
the body .
- Never strap more than one person , in­
cluding small children, into any belt.
- Never place a safety belt over a child sit­ ting on your lap.
- Always keep feet in the footwell in front
of the seat while the vehicle is being driv­
en .
- Never let any person ride with their feet on the instrument panel or sticking out
the window or on the seat.
- Never remove a safety belt while the ve­
hicle is moving. Doing so will increase
your risk of be ing injured or killed.
- Never wear belts twisted.
- Never wear belts over rigid or breakable
objects in or on your clothing, such as
eye glasses, pens, keys, etc., as these
may cause injury.
- Never allow safety belts to become dam­
aged by being caught in door or seat
hardware .
- Do not wear the shoulder pa rt of the belt
under your arm or otherwise out of pos i­
tion . -
Several layers of heavy clothing may in­
terfere with correct positioning of belts
and reduce the overall effectiveness of
the system .
- Always keep belt buckles free of anything
that may prevent the buckle from latch­
ing securely .
- Never use comfort clips or devices that
create slack in the shoulder belt . Howev­
er, special clips may be required for the
proper use of some child restraint sys­
tems .
- Torn or frayed safety belts can tear, and
damaged belt hardware can break in an
accident. Inspect belts regularly .
If web­
bing, bindings, buck les, or retractors are
damaged, have belts replaced by an au ­
thorized Audi dealer or qualified work­
shop.
- Safety belts that have been worn and
loaded in an accident must be replaced
with the correct replacement safety belt
by an authorized Audi dealer . Replace­
ment may be necessary even if damage
cannot be clearly seen . Anchorages that
were loaded must also be inspected.
- Never remove, modify, disassemble, or
try to repair the safety belts yourself.
- Always keep the belts clean. Dirty belts
may not work properly and can impair
the function of the inert ia reel
c:> page 200, Safety belts .
Safety belts
Belt positioner
The driver and front passenger seats are
equipped with belt positioners .
Fig. 14 7 Driver 's se at: Be lt positio ner

The front seats are equipped with belt posi­
tioners so it is easier to fasten the safety be lts . The belt positioners automatically ex ­
tend when the door closes and the ignition
switches on ¢
fig. 147.
The belt positioner returns to its starting posi­
tion again when
- the tongue in the belt latch engages o r the
belt was not fastened within 60 seconds .
- yo u sw itch the igni tion off.
- you ope n the door.
_& WARNING
- O nly you r autho rized Aud i de ale r shou ld
wor k on the sys tem or remove and instal­
ling system components when perform ­
ing other work .
- T he be lt positioners could cause in jury or
damage if they pinc h peop le or objects
when extending or retracting .
Fastening safety belts
Safety first -everybody buckle up!
Fig . 14 8 Be lt buckle and tongue on t he driver's seat
To provide maximum protection, safety belts
must always be posit ioned correctly on the
wearer's body .
~ Adjust the front seat and head restraint
properly¢
page 61, Seats and storage.
~ Make sure the seatback of the rear seat
bench is in an upright pos ition and securely
latched in place before using the belt¢ ..
&.
~ Hold the belt by the tongue and pull it even-
ly across the chest and pelvis¢,&..
Safety belts 133
~ Insert the tongue into the correct buck le o f
your seat unti l you hear it latch securely
¢ fig. 148.
~ Pull on the belt to make sure that it is se-
curely latched in the buckle.
Automat ic safety belt r etractor s
Every safety belt is equipped with an automat ­
ic be lt ret ractor on the shoulder belt. This fea­
ture locks the belt when the be lt is pulled out
fast, during hard brak ing and in an accident.
The belt may also lock when you drive up or
down a steep h ill or th rough a sharp cu rve.
During normal driv ing the belt lets you move
freely.
Safety belt pretensioners
The safety belts are equipped with a belt pre­
tensioner that helps to tighten the safety belt
and remove slack when the pretensioner is ac­
tivated. The function of the pretensione r is
monito red by a warn ing light¢
page 20.
Switchable locking fe ature
Every safety belt except the one on the driver
seat is equipped with a sw itchable lock ing fea­
ture that
must be used when the safety belt is
used to attach a ch ild safety seat . Be s ure to
read the important information about this
feature
¢page 168.
_& WARNING
Imp roperly posit ioned safety be lts can
cause serious injury in an accident
¢ page 134, Safety belt position .
-Safety belts offer opt imum protection
only when the seatback is upr ight and
be lts are properly posit io ned on the
body.
-
- Never attach the safety be lt to the buck­
le for another seat. Attaching the belt to
the wrong buckle will reduce safety be lt
effectiveness and can cause ser ious per­
sonal injury.
- A passenger who is not properly restrain-
ed can be seriously injured by the safety .,.

-Improper repair or disassembly of the
front passenger and driver seat will pre­
vent the Advanced Airbag System from
functioning properly .
- Repairs to the front passenger seat must
be performed by qualified and properly
trained workshop personnel.
- Never remove the front passenger or
driver seat from the vehicle .
- Never remove the upholstery from the
front passenger seat .
- Never disassemble or remove parts from
the seat or disconnect wires from it.
- Never carry sharp objects in your pockets
or place them on the seat. If the weight­
sensing mat in the passenger seat is
punctured it cannot work properly.
- Never carry things on your lap or carry
objects on the passenger seat . Such
items can increase the weight registered
by the weight-sensing mat and send the
wrong information to the airbag control
unit.
- Never store items under the front pas­
senger seat. Parts of the Advanced Air­
bag System under the passenger seat
could be damaged, preventing them and
the airbag system from working proper­
ly.
- Never place seat covers or replacement
upholstery that have not been specifical­
ly approved by Audi on the front seats.
- Seat covers can prevent the Advanced
Airbag System from recognizing child re­
straints or occupants on the front pas­
senger seat and prevent the side airbag in the seat backrest from deploying prop­
erly.
- Never use cushions, pillows, blankets or
similar items on the front passenger
seat . The additional padding will prevent
the weight-sensing mat in the seat from
accurately registering the child restraint
or person on the seat and prevent the
Advanced Airbag System from function­
ing properly.
- If you must use a child restraint on the
front passenger seat and the child re-
Airbag system 145
straint manufacturer's instructions re­
quire the use of a towel, foam cushion or
something else to properly position the
child restraint, make certain that the
PASSENGER AIR BAG OFF light comes
on and stays on whenever the child re­
straint is installed on the front passen­
ger seat.
- If the
PASSENGER AIR BAG OFF light
does not come on and stay on, immedi­
ately install child restraint in a rear seat­
ing position and have the airbag system
inspected by your authorized Audi dealer .
How the Advanced Airbag System
components work together
The front Advanced Airbag System and the
side airbags supplement the protection of­
fered by the front three-point safety belts
with pretensioners and load limiters and the
adjustable head restraints to help reduce the
risk of injury in a wide range of accident and
crash situations. Be sure to read the impor­
tant information about safety and heed the
WARNINGS in this chapter.
Deployment of the Adv a need Airbag System
and the activation of the safety belt preten­
sioners depend on the deceleration measured
by the crash sensors and registered by the
electronic control unit. The amount of infla­
tion of the front airbags can also be adapted
to the front sea t position, depending on the
distance between the respective front seat
and the steering wheel or instrument panel as registered by sensors in the seats. Crash se­
verity depends on speed and deceleration as
well as the mass and stiffness of the vehicle
or object involved in the crash.
On the passenger side, regardless of safety
belt use, the airbag will be turned off if the
weight on the passenger seat is less than the
amount programmed in the electronic control
unit. The front airbag on the passenger side
will also be turned off if one of the child safe-
ty seats that has been certified under Federal
Motor Vehicle Safety Standard 208 has been
recogni zed on the seat . The
PASSENGER AIR .,,.
•
•

dampened with dish detergent and water is recommended.
(D Note
- To avoid sc ratch ing the disp lay, yo u
shou ld never clean it dry.
- To preven t damage, ma ke s ure fl uids do
not enter the controls .
Aluminum trim
Use only neutral-pH products to remove spots
and depos its from alum inum s urfaces.
C hrome care products and alkaline cleaners
will attack alum inum surfaces and can dam­
age them over time .
A WARNING
Always read and heed all WARNINGS and
other information ~
page 189.
Fabrics and fabric coverings
Fab rics and fabr ic coveri ngs (e.g . seats, doo r
tr im panels, etc.) should be cleaned at reg ula r
i nte rva ls wi th a vac uum cleaner . Thi s removes
sur face dirt particles which could become em­
bedded in the fabr ic through use . Steam
cleane rs shou ld not be used, because the
steam tends to push the dirt deeper into the
fabric and lock it there.
Normal cleaning
Generally, we recommend using a soft sponge
or a lint-free microfiber cloth to the clean fab­ ric. Brushes should on ly be used for carpets
and floor mats, s ince other fabric surfaces
could be harmed by brushes.
Normal surface sta ins can be cleaned using a
commercia lly available foam cleaner. Spread
the foam on the surface of the fabric with a
soft sponge and work it in gently. Do not sat u­
rate the fabric. Then pat the foam d ry using
absorbent, dry cloths (e .g . microfibe r cloth)
and vacuum it afte r it has dr ied comp lete ly .
Cleaning and protec tion 197
Cleaning sta ins
Stains caused by bever ages (e.g . coffee, fr uit
ju ice, etc.) can be treated with a mild deter ­
gent solution. Apply the detergent so lution
with a sponge. In the case of stubborn stains, a detergent paste can be applied directly to
the stain and worked into the fabric . After­
wards, use copious amounts of clean water to
remove the rema ining deterge nt. Apply the
water wit h a damp cloth or sponge and pat
t h e fabric dry with an abso rbent, dry clot h.
Stai ns from choco late or makeup should have
detergent paste rubbed i nto them . After ­
wards, remove the soap w ith water (damp
sponge).
A lcohol can be used to treat stai ns from
grease, o il, lipstick or a ballpoint pen . M elted
grease or dye must be patted off using ab­
sorbent mater ial. It may be necessa ry to re ­
t reat the areas with de tergent pas te and wa­
te r.
In the case of gene ral soiling of the uphols­
tery a nd cover material, we recommend hir ing
a speci alist t hat h as the eq uipment to clean
t h e se at cove rs and othe r fabr ic surfaces by
shampooing and spray extraction.
A WARNING
A lways read and heed all WARNINGS and
the information
~ page 189.
(D Tips
Open Ve lcro fas teners on yo ur clothing can
damage the seat cover . Please make sure
that Ve lcro fasteners are closed .
Plastic parts and instrument panel
Always use a clean cloth moistened in clear
water to clean these areas. For persistent d irt
use a n Aud i approved
solvent-free p lastic
clea ner/protectant .
•
•