light AUDI RS5 CABRIOLET 2015 Owners Manual

M N
er
u..
co ,...., \!) ..,.,
,...., ..,., ,....,
Vehicl e ca re a nd cl eanin g 18 5
Rinse the vehicle thoroughly with water. Then
clean using a neutral shampoo and a soft mi­
crofiber cloth.
Rinse the vehicle tho roughly again and let it
air dry. Remove any water residue using a
shammy .
A WARNING
-Only wash the vehicle when the ignition
is off and follow the instructions from
the car wash operator to reduce the risk of accidents .
- To reduce the risk of cuts, protect your­
self from sharp metal components when
wash ing the underbody or the inside of
the wheel housings .
- After washing the vehicle, the braking ef­
fect may be delayed due to mo isture on
the brake rotors or ice in the winter. The
brakes must be dried first with a few
careful brake applicat ions.
- If you wash the vehicle in an automatic car wash, you must fold the exterior m ir­
rors in to reduce the r is k of damage to
the mirrors. Power folding exterior m ir­
rors* must only be folded in and out us­
i ng the power folding function. -
To prevent paint damage, do not wash
the vehicle in direct sunlight.
- T o reduce the r isk o f damage, do not
wash the power top with a pressure
washer.
- To reduce the risk of damage to the sur ­
face, do not use insect removing spong­
es, kitchen sponges or similar items.
- Matte finish painted vehicle compo­ nents:
- To reduce the risk of damage to the surface, do not use polishing agents or hard wax.
- Never use car wash cycles that apply
protective wax. It can destroy the
matte fin ish effect.
- Do not place any stickers or magnet ic
signs on vehicle parts painted w ith
matte fin ish paint. The paint cou ld be
damaged when the stickers o r magnets
are removed.
@ For the sake of the environment
Only wash the vehi cle in facilities spec ial ly
designed for that purpose. This will red uce
the risk of dirty water contaminated with
oil from entering the sewer system.
Cleaning and care information
When clean ing and caring for individua l vehi ­
cle components, refer to the fo llowing tab les.
The information contained there is simply rec­ ommendations . For questions or for compo- nents that are not listed, re
fer to an author­
ized Audi dea ler or qualified workshop . A lso
follow the information found in
Q & .
Cle anin g ext erio r
Component Situation Solution
Wipe r bl ade s
Dirty <=> page 5 7, Cleaning windshield wiper blades
Hea dli ght s/ Dir ty Soft sponge with a m
ild soap solutional
tail li ghts
S en so rs /
Dirty Sensors: soft cloth with a so lvent-free cleaning product
c a mera l ense s Camera lenses: soft cloth with an alcohol -free cleaning
solution
Snow/ice Hand brush/so
lvent-free de-icing spray
•
•

M N
er
u..
co ,...., \!) ..,.,
,...., ..,., ,....,
Vehicl e ca re a nd cl eanin g 18 7
Component Situ ation Solution
P las tic parts
Dirty Damp cloth
Heavily soiled Mild soap solutional, solvent-free plastic cleaning solu-
t ion, if necessary
Di spl ays Dirty Soft cloth with LCD cleaner
Co nt rols Dirty Soft brus
.h, then a soft cloth with a mild soap solutio nal
S afe ty be lt s Dirty Mild soap solutional, allow to dry before letting them re-
tract
Tex tile s, Stains adhering to
Vacuum cleaner
Vin yl, the surface
Alcantara Water-based stains Absorbent cloth and m ild soap solutional
such as coffee, tea,
blood, etc.
Oil-based stains Apply a mild soap solutional, blot away the dissolved oil
such as oil, make- or dye, treat afterward w ith water, if necessary
up, etc.
Special stains such Special
stain remover, blot with absorbent material,
as ballpoint pen, treat afterward with mild soap solutional, if necessary
nail polish, latex
paint, shoe polish,
etc.
N atur al lea ther Fresh stains Cotton cloth with a mild soap solutiona>
Water-based stains Fresh stains: absorbent cloth
such as coffee, tea, Dried stains: stain remover suitable for leather
blood, etc.
Oi l-based stains Fresh stains: absorbent cloth and stain remover suitable
such as oil, make- for leather
up, etc. dried stains: Oil cleaning spray
Special stains such Sta in remover sui table for leather
as ballpoint pen, nai l polish, latex
pa int, shoe polish,
etc.
Ca re Regularly apply condit ion ing c ream that protects from
light and penetrates into the mater ial. Use specially-col-
ored condit ioning cream, if necessary.
Carb on p art s Dirty Clean the same way as plastic parts
al Mild soap solution: maximum two tablespoons neu tral soap in 1 quart ( 1 lite r) of water
& WARNING
T he windshie ld may not be treated with
wate r-repelling windshie ld coating agents .
Unfavorab le conditions such as wetness,
darkness, or low sun can result in in-
-
creased glare. Wiper b lade chatter is also
possib le.
(D Note
- Hea dlight s/tail ligh ts
•
•

188 Vehicle care and cleaning
- Never clean headlights or tail lights
with a dry cloth or sponge.
- Do not use any cleaning product that
contains alcohol, because they could
cause cracks to form.
-Wheels
- Never use any paint polish or other
abrasive materials.
- Damage to the protective layer on the
rims such as stone chips or scratches
must be repaired immediately .
-Sensors/camera lenses
- Never use warm or hot water to re-
move snow or ice from the camera
lens. This could cause the lens to crack.
- Never use abrasive cleaning materials
or alcohol to clean the camera lens.
This could cause scratches and cracks.
- Power top
- Remove bird droppings immediately.
- Never use gasoline, stain remover, ben-
zene, paint thinner or other solvents to
remove stains.
- Windows
- Remove snow and ice on windows and
exterior mirrors with a plastic scraper.
To avoid scratches, move the scraper
only in one direction and not back and
forth.
- Never remove snow or ice from win­
dows and mirrors using warm or hot
water because this could cause cracks
to form.
- To avoid damage to the rear window
defogger, do not apply any stickers on
the heating wires on the inside of the
window.
- Decorative parts/trim
- Never use chrome care or cleaning
products.
-Paint
- To reduce the risk of scratches, the ve-
hicle must be free of dirt and dust be­
fore polishing or waxing.
- To prevent paint damage, do not polish
or wax the vehicle in direct sunlight. - To reduce the risk of paint damage, do
not polish away rust film.
- Remove cosmetics and sunblock imme­
diately. Otherwise, the paint could be
damaged.
- Displays
-To avoid scratches, do not use dry
cleaning methods on displays .
-Controls
- Make sure that no fluids enter the con-
trols, because this could cause dam­
age.
- Safety belts
- Do not remove the safety belts to clean
them.
- Never clean safety belts or their com­
ponents chemically or with corrosive
fluids or solvents and never allow sharp objects to come into contact
with the safety belts . This could cause
damage to the belt webbing.
- If there is damage to the webbing, the
connections, the retractors or the buck­
les, have them replaced by an author­
ized Audi dealer or qualified workshop.
-Textiles/Vinyl/ Alcantara
- Never treat Vinyl/Alcantara with leath-
er care products, solvents, floor polish,
shoe polish, stain remover or similar products.
- To avoid damage, have stubborn stains
removed by an authorized Audi dealer
or qualified workshop.
- Never use steam cleaners, brushes,
hard sponges, etc. when cleaning.
- Do not turn on the seat heating* to dry
the seat.
- Objects with sharp edges such as zip­ pers, rivets on clothing or belts can
cause damage to the surface.
- Open hook and loop fasteners, for ex­ ample on clothing, can damage seat
covers. Make sure hook and loop fas­
teners are closed .
-Natural leather

M N
er
u..
co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
-Never treat leather with so lvents, floor
polish , shoe polish, stain remover or
sim ilar products.
- Objects with sharp edges such as zip­
pers, rivets on clothing or belts can
cause damage to the surface.
- Never use steam cleaners, brushes ,
hard sponges, etc. when cleaning.
- Do not turn on the seat heating* to dry
the seat .
- To help prevent the leather from fad­
ing, do not leave the vehicle in direct
sunlight for long periods of time. If
leaving the vehicle parked for long pe­
riods of ti me, you should cover the
leather to protect it from direct sun­
light.
Q) Tips
- Insects are eas ier to remove from paint
that has been freshly waxed .
- Regu lar wax ing can prevent rust film
from forming .
Vehicle care and cleaning 189
•
•

190 Fuel supply and filling your fuel tank
Fuel supply and filling
your fuel tank
Gasoline
Fuel supply
Using the righ t fuel helps keep the environ­
ment cle an and preven ts engine dam age .
Fuel recommendation
The fuel recomme nded for you r vehicle is un­
lead ed premium
g rade gasoline . Audi recom­
mends using TO P TI ER D ete rgent Gaso line
wi th a minimum oc tane ra ting of 91 A KI ( 95
RON ). For more informa tio n o n TO P TIE R De­
tergen t Gasoline, please go to the off icia l
website (www .to ptiergas .com) .
Th e re commended gasoline o ctane rating for
your eng ine can also be fo un d o n a label loc at­
ed on the ins ide of the fue l filler flap . This ra t­
in g may be specified as AKI or RON.
Your veh icle may also be operated using un­
l e ad ed regular g asoline with a min imum o c­
tane rating o f 87 AKI/9 1 RO N. H owever, using
87 AKI/91 RO N octane fue l w ill slightly re­
d uce eng ine perfo rmance .
Use unleaded ga soline only. Unleaded g aso­
li ne is availab le th rougho ut the USA, Canada,
and in most E uropean countries . We recom­
mend that you do not ta ke yo ur vehicle to
areas or countries where unleaded gasoline
may not be ava ilable.
F or mo re informat io n on refue ling your ve hi­
cle, see
¢ page 191.
Octane rating
Octane rating ind icates a gaso line' s abili ty to
r es ist eng ine da mag in g "kno ck" cau sed b y
p rem ature ign ition and detona tion. Therefore,
b uying the correct grade of gasoline is very
important to he lp prevent possible engi ne
damage and a loss o f engine performance.
Gasoline mos t commonly used in the Unite d
States an d Canada has the following octane
rat ings that can usually be fo und on the filler
p ump : -
Premium Grade: 9 1 -96 AKI
- Regular Gra de: 87 -90 AKI
Explanation of the abbreviations:
AKI = Anti Knock In d ex = (R+ M)/2 = (RO N
+ MO N)/2
R ON = Research Octane Number
MON = Moto r Octane Number .
@ Note
-Do not use a ny fue l w it h octane rat ings
lower tha n 87 A KI or 9 1 RO N othe rwise
ex pensive eng ine da mage w ill occu r.
- Do
not use lea ded gasoli ne. The use of
leaded g asoline w ill sev ere ly damag e
yo ur vehicle's ca ta lytic converter a nd its
a bi lity to cont rol exh aust emis sions.
Blended gasoline
Use of gasoline containing alcohol or
MTBE (methyl tertiary butyl ether )
You may use unleaded gasoline blende d with
alcohol or MTB E (commonly referred to as
oxygenates) if the blended m ixture meets t he
fo llow ing c riteria:
Blend of gasoline methanol (wood alcohol or
methyl alcohol )
-Anti -kno ck index mus t be 87 A KI or higher .
- Blend mus t contain no more t han 3% me th-
a nol.
- Blend must contain mo re than 2% co-sol -
ve nts .
Blend of gasoline and ethanol (grain alcohol
or ethyl alcohol)
- Anti-knock index must be 87 AKI or higher.
- Blend must not conta in mo re than 10%
ethanol.
Blend of gasoline and MTBE
- Anti -kno ck index mus t be 87 A KI or higher.
- Blend must contain not mo re than 15%
M TB E.
Seasonally adjusted gasoline

"' N
a: LL co
rl I.O
"' rl
"' rl
Checking and filling Engine hood
Releasing and opening the engine hood
The engine hood is released from inside the
vehicle .
Fig . 172 Dr iver's side footwell: eng ine hood release
lever
F ig . 173 Re lease lever un der the engine hood
Before opening the engine hood, make sure
that the windshield w ipers are flat against the
windshield. Otherwise, they could damage the
paint on the hood.
.. With the driver's door open, pu ll the lever
under the instrument panel in the direction
of the arrow
q fig. 172.
.. Raise the hood slightly q &.
.. Press the rocker switch under the hood up­
ward
c::> fig . 173 . This re leases the catch .
.,. Open the hood.
& WARNING
Hot engine coo lant can burn you.
- To redu ce the r isk of being burned, never
open the hood if yo u see or hear steam
or coolant escaping from the engine
compartment. Wait until no steam or
Checkin g and fillin g 195
coolant can be seen or heard before care­
fully opening the hood.
Closing the engine hood
.. Pull the hood down until the pressure from
the struts is reduced .
.. Let the hood
drop down and latch in place .
Do not try to push it shut; it may fail to en­
gage
q &, .
_&. WARNING
-
A hood that is not comple tely latched
could fly up and b lock your view while dr iv­
ing.
- When you close the engine hood, chec k it
to make sure the safety catch has p ro pe r­
ly engaged . The hood sho uld be flush
with the surrounding vehicle body parts .
-If you notice while driv ing that the hood
is not secured prope rly, stop at once and
close it.
Working in the engine compartment
Be especially careful whenever you work in the engine compartment .
Whenever yo u mu st p erform an y w or k in th e
eng in e compa rtment, for example checking
and filling differ ent fluid s, there i s a ri sk of
injury , burns and accidents. To prevent per­
sonal injury always obser ve the following
WARNINGS . The eng ine compa rtment of an y
v ehicle is a hazardous are a
q A.
_&. WARNING
To help avoid injury, before you check any­
thing under the hood:
- Turn off the engine.
- Remove the ignition key.
- Apply the parking brake .
- Move selector lever of automatic trans -
mission to "P" (Park).
- Always le t the engine cool down . Hot
components wi ll bur n skin on contact .

"' N
a: LL co
rl I.O
"' rl
"' rl
Checking and fillin g 197
Engine compartment
Engine compartment
These are the most important items that you can check.
Fig. 174 Typical layout for containers and engine oil filler cap
(D Coolant expansion tank (- L) . . . 202
@ Jump start point(+) under a cov-
er .. .. ... ....... ........ ..
207, 256
@ Engine o il filler cap (<t=r.) . . . . . 199
@ Jump start point(-) with hex
head screw ............ .... .
207, 256
© Brake flu id reservoi r((())) . . . . . 204
® W indshie ld/headlight* washer
container
(0) . . . . . . . . . . . . . . 208
A WARNING
Before yo u check anything in the engine
compartment, always read and heed all
WARNINGS
q .& in Working in the engine
compartment on page 195.
-
Engine oil
Engine oil specifications
The engine oil used must conform to exact
specifications .
The service interval disp lay in the instrument
cluster of your vehicle will inform y ou when it
is time for an oil change. We recommend that
you have your oil changed by an authorized
Audi Se rv ice Advisor .
If you have to top off the o il between o il
changes, use the Audi o il quality standard
specified in the tab le.
Audi oil quality standard
Gasoline
VW 502 00 or
eng ine vw 504 00 ...

198 Checking and filling
Using the proper engine oil is important for
the functionality and service life of the en­
gine. Your engine was factory-filled with a
high-quality oil which can usually be used
throughout the entire year.
0 Note
Your Limited New Vehicle Warranty does
not cover damage or malfunctions due to
failure to follow recommended mainte­
nance and use requirements as set forth in
the Audi Owner's Manual and Warranty
&
Maintenance booklet.
- Use only a high quality engine oil that ex­
pressly complies with the Audi oil quality
standard specified for your vehicle's en­
gine . Using any other oil can cause seri­
ous engine damage.
- Do not mix any lubricants or other addi­
tives into the engine oil. Doing so can
cause engine damage.
If you need to add oil and there is none
available that meets the Audi oil quality
standard your engine requires, you may
add a total of no more than 0.5 quart/liter
of a high-quality "synthetic"oil that meets
the following specifications.
- Vehicles with gasoline engine: ACEA A3
or API SM with a viscosity grade of
SAE 0W-30, SAE SW-30 or SAE SW-40.
- For more information about engine oil
that has been approved for your vehicle, please contact either your authorized
Audi dealer or Audi Customer Relations
at 1 (800) 822-2834 or visit our web site
at www.audiusa .com or
www .audicanada .ca .
Engine oil consumption
The engine in your vehicle depends on an ade ­
quate amount of oil to lubricate and cool all
of its moving parts.
In order to provide effective lubrication and
cooling of internal engine components, all in­
ternal combustion engines consume a certain amount of oil. Oil consumption varies from
engine to engine and may change significantly
over the life of the engine. Typically, engines
with a specified break-in period (see
¢ page 179) consume more oil during the
break -in period than they consume after oil
consumption has stabilized.
Under normal conditions, the rate of oil con­
sumption depends on the quality and viscosity
of the oil, the RPM (revolutions per minute) at
which the engine is operated, the ambient
temperature and road conditions . Further fac­
tors are the amount of oil dilution from water
condensation or fuel residue and the oxida­
tion level of the oil. As any engine is subject to
wear as mileage builds up, the oil consump­
tion may increase over time until replacement of worn components may become necessary.
With all these variables coming into play, no
standard rate of oil consumption can be es­
tablished or specified. There is no alternative
to regular and frequent checking of the oil lev­ el, see
Note.
If
the yellow engine oil level warning symbol
El in the instrument cluster lights up, you
should check the oil level as soon as possible
¢ page 199. Top off the oil at your earliest
convenience
¢ page 199.
A WARNING
--
Before you check anything in the engine
compartment, always read and heed all
WARNINGS¢
& in Working in the engine
compartment on page 195.
{(D Note
Driving with an insufficient oil level is like­
ly to cause severe damage to the engine .
(D Tips
- The oil pressure warning display. is
not an indicator of the oil level. Do not
rely on it. Instead, check the oil level in
your engine at regular intervals, pref­ erably each time you refuel, and always
before going on a long trip. .,.

202 Checking and filling
Checking the engine coolant level and
adding coolant
Be very careful when adding engine coolant.
Fi g. 1 77 En g in e c ompart men t: C over on the coola nt
ex pan sion ta nk
Fig. 178 Engine co mpar tment : ma rkin gs in th e coolant
ex pan sio n ta nk
Before you che ck anything in the engi ne com­
partment,
a lwa ys r ead and heed all WARN­
INGS c> A in Working in the engine compart ­
ment on page
195.
The "M IN " und "MAX " mark ings a re found o n
the bi -level disc in the in terior of the coolant
expansion tank
¢ fig . 178.
.,. Pa rk you r vehi cle on a level sur face .
.,. Turn off t he igni tion.
.,. Let the engine coo l down .
.,. Place a thick rag over the coolant expansion
tank and
c a refully turn the cap cou nte r­
clockwise
c> _&. .
.,. Read the eng ine coolant level inside the
coolant expans io n tank
c> fig . 177,
c>page 197 , fig. 174 . With a cold engine,
the coolant level sho uld be betwe en the
" M IN " and "MAX " ma rkings <=>
fig. 178
-arrows- . W he n t he eng ine is wa rm, the lev­
el may be slightly
above the "MAX" marking . .,.
Add coo lant mixed in the correct rat io, if
necessary
c> page 201 . Coolant may be a
maxim um of 1 mm above the MAX marking .
.,. Twist the cap on again
tightly.
The location of the coo lant expansion tan k
can be seen i n the engine compartment illus ­
tration
c> page 197.
T o obtain an acc urate reading, the engine
must be sw itched off.
T he ex pan sion ta nk in your vehicle is eq uipped
with an ele ctric coo lant level senso r.
When the coolant level is too low , the wa rn ing
li ght in the Au to-Check System <=>
page 17 will
blink u nti l yo u ad d coolant and the level has
been restored to normal. Eve n t hough t here i s
an e lectri c coo lant level senso r, we still rec ­
ommend you check the coola nt level from
time to t ime.
Coolant loss
Coolant loss may indica te a leak in the cooling
system. In t he event o f coolant loss, the coo l­
i ng system shou ld be inspected immediately
by your a uthorized Audi dea ler . It is not
eno ugh mere ly to add coolant.
In a
sealed sys tem, losses can occur on ly i f
the boili ng point o f the coo lant is exceeded as
a res ult of overheating.
Adding coolant
Rep la cement engine coo la nt must conform to
exact spe cificat ions
c> page 201, Cool ant .
We recommend using only coolant add it ive
Gl 2++ , Gl3 or in an emergency G 12 +. Do not
use a diffe rent add itive. In an emerge ncy use
plain w ater until yo u can get the correc t addi­
tive a nd can res tore the cor rect ra tio. T hi s
sho uld be done as soon as possib le .
If you have lost a considerab le amou nt of
c oolant , the n you shoul d a dd cold an tifreeze
and co ld wate r on ly w hen the e ng ine is cold.
Always use
n ew engine coo lant w hen refilling .
Do not f ill coo la nt
above the "MA X" mark. Ex-
cess coolant will be forced o ut through the .,,_

M N
er
u..
co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
pressure relie f valve in the cap when the en­
gine becomes hot.
A WARNING
- The cooling system is under pressure and
can get very hot. Reduce the risk of
sca lding from hot coolant by following
these steps .
- T urn off the engine and a llow it to cool
down.
- Protect your face, hands and arms from
escap ing flu id and steam by cover ing
the cap with a large, thick rag.
- Tu rn the cap slowly and very ca refully
in a counte r-clockw ise d irection while
applying light, downward p ress ure on
the top of the cap.
- To avo id being burned, do not sp ill an­
tifreeze or coolant on the exhaust sys­
tem or hot engine parts. Under certain
conditions, the ethylene glyco l in en­
g ine coolant can catch f ire.
- Antifreeze is poisonous. Always store an­
t ifreeze in its or iginal container and we ll
out of the reach of children.
- If you drain the coolant, it must be
caught and safely stored in a proper con­
tainer clear ly marked "poison".
Q) Note
- Do not add any type of radiator leak sea l­
ant to your veh icle's engine coolant.
Adding rad iator repair fluid may adverse­
l y affect the function and performance of
you r cooling system and could result in
damage not covered by your New Vehicle Limited Wa rra nty.
- Coolant pollutes the env ironment and
could cause an engine fire. Excess coo l­
ant w ill be forced ou t through the pres­
su re re lief va lve in the cap when the en­
gine becomes hot .
- If, in an emergency, only water can be
added, t he cor rect ratio between wate r
and an tifreeze<=> page 201 must be re ­
stored as soon as possib le .
Checkin g and fillin g 203
'
@) For the sake of the environment
Drained coolant sho uld not be reused. A l­
ways d ispose of used coolant while observ­
i ng a ll environmental regulations.
Radiator fan
The radiator fan switches on automatically by
itself .
T he radiator fan is dr iven by the engine via the
V-belt. The viscous clutch regulates the speed
of the fan according to the temperature of the coolant.
An a uxiliary electric radiator fan* switches on
and off depending on coolant temperature
and othe r vehicle ope rat ing cond it ions.
After yo u switch the eng ine off, the aux iliary
f an can continue running for up to 10 m inutes
- even with the ignition off. It can even switch
on again later by itself<=>.&. , if
- t he temperatu re of the engine coo lant rises
due to the heat build -up from the engine in
the engine compa rtment, or
- the engine compa rtment heats up because
the vehicle is parked in intense sunlight.
A WARNING
=
- To reduce the risk of personal inju ry nev-
er touch the radiator fan.
- The a uxiliary electric fan is tempe rat ure
contro lled and can switch on suddenly
even when the engine is not running.
- The a uxiliary radiator fan switches on a u­
tomatically when the engine coo lant
reaches a certain temperature and will
continue to run until the coo lant temper­
ature drops.
•
•