AUDI S6 2014 Owners Manual

@ Tips
-Side assist is not active whi le you are
making the adjustment.
- Your settings are automatica lly stored
and assigned to the remote control key
being used.
Driver messages
Applies to vehicles: with side assist
If side ass ist switches off by itself, the LED in
the button turns off and a message will ap­
pear in the instrument cluster d isplay:
Audi side assist: Currently unavailable . No
sensor vision
The radar sensors' vision is affected. Do not
cover the area in front of the sensors with bike
wheels, stickers, dirt or other objects. Clean
the area in front of the sensors, if necessary
c>page97, fig.101.
Audi side assist: Currently unavailable
Side assist cannot be swi tched on temporarily
because there is a malfunction (for example,
the battery charge leve l may be too low) .
Audi side assist: System fault!
The system cannot guarantee that it will de ­
tect vehicles correctly and it is switched off .
The senso rs have been displaced or are faulty.
Ha ve the sys tem checked by an authorized
Aud i dealer o r autho rized Aud i Service Fac ilit y
soon.
Audi side assist: Unavailable when towing.
Side assist sw itches off automatically when a
factory- installed trailer hitch is connected to
the electrical connector on the trailer. There is
no guarantee the system will switc h off when
using a retrofitted trailer hitch. Do not use
side assist when towing a trailer .
Audi side assist 99

100 Audi drive select
Audi drive select
Driving settings
Introduction
Aud i d rive select mak es it possible to expe ri­
ence diffe ren t types of vehi cle se ttin gs i n o ne
ve hicl e. The dr ive r can se lect th ree
Comfort ,
Auto and Dynamic modes in the M MI to
switch between a sporty and a comforta ble
driving mo de.
You c an a lso a djust the setti ng according to
your p re ferences in the
Individual mode . F o r
examp le, you ca n combine settings such as a
sporty en gine t uning with comfortab le steer­
ing.
A WARNING
Improper use of the A udi drive select can
cause collisions, ot her acc idents and se ri­
ous pe rsonal injury.
Description
The vehicle setup in each mode depends on
the veh icl e's featu res. The engine, t ransm is­
sion, stee ring, reve rsible sa fe ty belt tension­
e rs a nd adap tive air su spension are alw ays in­
volved.
Engine and transmission
Depending on the mode, the e ng ine and the
tra nsmission respond quic ker or i n a more bal­
an ced manne r to acce le rator pedal move­
men ts. In the sporty dyn ami c mode, the
tra nsmission sh ifts at highe r RP Ms.
Air suspension*
The adaptive air suspens ion/adaptive air sus­
pension spor t*
(Air suspen sion in the MM I) is
a n e lec tronic ally con trolled air suspension and
da mpi ng sys tem. They are adjus ted depend­
ing on the se lected driving mode, the drive r's
steeri ng, braking an d acceleration input and
the road s urface, ve hicle speed and load. A
sporty setting is generally used in ve hicles
with adaptive air suspension sport*. T
he veh icle clearance varies depending on the
se lected mo de an d the speed .
T he highway setti ng is a ct ivated automatic ally
whe n you dr ive above 7 5 mph (120 km/ h) fo r
more than
3 0 seconds in the Auto or Dynamic
mode. The gro und clea rance is increased a uto ­
matically if the speed drops below
44 mph
(70 km/h) for more than 120 seconds.
Steering
T he s teer ing adap ts in terms of s teer ing effor t
and steering ratios . Indirect stee ring that
moves easily, like the steer ing in comfo rt
mode, is best suited to long drives on a high­
way. In contrast, dynamic mode provides sporty, direct steer ing .
Sport differential*
As a component of the all whee l drive system
(quattro)
¢ page 198, the Sport differential *
dist ributes the driving power to the rear ax le
depending on the sit uat ion. The distrib ution
of power var ies depend ing on the selected
mode, from balanced (comfort) to agile (dy­
nam ic) . Th e goal is a h igh level of ag ility and
ability to acce lerate on cu rves . Th e ve hicl e is
very res ponsive to stee ring.
Curve light*
The curve light adapts to driving on curves .
T he pivo ting act io n and the lighting are also
adapt ed to the mode .
Adaptive cruise control*
The behav ior when accelerating can be adjust­
ed from comfortab le to sporty, depending on
the drive select mode. Adaptive cru ise cont ro l
also responds to th e dr iv ing behavior o f th e
vehicle a head in a mo re co nse rvative o r sporty
man ne r.
Engine sound*
The sound of the eng ine is adapted to the se­
lected mode and ranges from sub tle to sporty . .,.

(D Note
-Make sure there is enough clearance
above and below the veh icle when park­
ing. The height of the vehicle can change
once it is parked due to temperature
fluctuations, changes to the load cond i­
tions and changes to the dr iv ing modes,
which can affect clearance .
- When t ransporting the veh icle on a car
carr ier, tra in, ship or by other means, on­
l y tie the veh icle dow n at the runni ng
su rface of the tires, which is the ou ter
ci rcumference . Secur ing t he vehicle at
the a xle components, s uspension str uts
or tow ing eyes is not pe rm itted because
the pressu re in the air suspension st ruts
can change during transport. The vehicle may not be secu red sufficiently if this
happens.
- If you are going to tow a trailer, you
must activate the trailer operation mode
<=> page 206.
{!) Tips
-In some models, the maximum vehicle
speed can only be reached in the
Auto
and Dynami c modes.
- Se lecting the
Dynamic mode results in
spo rty sh ifting character istics. The S
gear posit ion engages automatically.
- In vehicles with spo rt differential", the
Dynamic mode is deactivated when tow­
i ng a trailer.
Adjusting the Individual mode
Audi dri ve sele ct 101
Selecting the driving mode
You can choose between Comfort, Auto, Dy­
namic and Individual .
Fig. 103 MMI: D rive select
.,.. To select the mode, se lect the following in
the MMI: ICARlf unction button>
Comfort ,
Auto , Dynamic or Individual.
You can change the d riv ing mode when the ve­
hicle is stationary or wh ile driving.
If traffic
permi ts, after changing modes, briefly take
yo ur f oot off the acce lerator pedal so that the
recently selected mode is a lso activated for
the engine.
Comfort -prov ides a comfor t-orie nted veh icle
setup and is s uited fo r long drives on h igh­
ways .
Auto -provides an overall comfo rtable yet dy­
nam ic dr iving feel and is suited for every day
u se .
Dynamic -gives the driver a sporty d riving
feel and is suited to a spo rty driv ing style .
Individual -<=> page 101.
_.& WARNING
-Pay attention to traffic when operating
Audi d rive select to prevent potential risk
of an ac cident.
-
You can adjust the vehicle settings to your personal preferences .
.,.. Se lect : I CARI funct ion button> Set ind ividu ­
al
control button. You can now adjust the in­
dividua l systems. The
Indi
vidu al driving mode wi ll automatical­
ly be activated when you have finished config-
uring the sett ings. ..,_

102 Audi drive select
The equipment in your vehicle w ill determine
which settings you ca n adj ust. The fo llowing
Systems Comfort
Engine /Tran smission
balanced
Air suspension * comfortable
Steering comforta ble
Sport d iff erent ial * balanced
Curve light* comfortab le
Belt tensioner * Standard
Adaptive cruise control * comfortable
Engine sound* subtle table p
rov ides a n overview of the characteris ­
tics of eac h driving mode .
Auto Dynamic
balanced sporty
ba lanced sporty
ba lanced spo
rty
ag ile sporty
ba lanced spo
rty
Standard Deployment time
adapted
ba lanced sporty
subtle/spo rtyal
sporty
al Subtle in the driving pos itio n D and sporty in th e d riving pos itio n S.
{DJ Tips
Your Individual mode se ttings are a uto­
mat ica lly store d an d assig ned to t he re­
mote co ntro l key being use d.
Raising/lowering the
vehicle
Raising the vehicle
You can ra ise your veh icle tempora rily, for ex­
ample to dr ive over a tall curb.
., Se lect the following in the
MMI: ICAR !f u nc ­
tion button >
Raise contro l button .
., Wait for the arrows in the display to stop
blinking and the vehicle to reach its fina l po­
s it ion.
Lowering the vehicle
., To lower t he veh icle, select the fo llowing in
the
M MI: ICARlfunction button> Lowe r con­
t ro l button .
., Wait for the a rrows in the display to stop
blinking and the vehicle to lower complete­
l y.
{(D Note
- Remember that your veh icle is not s uita­
ble for driving offroad even when it is
r aised. There is not enough ground clear­
ance. -
If the vehicle is ra ised, it will lower auto­
m at ically whe n driving 6 2 mph (1 00 km/
h) or faster .
Driver messages
Air suspen sion : vehicle currently too low .
Level control running
Air su spension : vehicle curr ently too high .
L e vel control running
The driver message switc hes off when the lev­
el cont rol process is comp lete .

Night vision assistant
Night vision assistant
with detected pedestrian marking
Description
App lies to vehicles: with night v isio n assistant
Fig . 104 Display: nig ht v is ion assistant
"N ight v is ion assistant with pedestrian detec­
tion" uses an infrared camera to monitor the
area in front of your vehicle at night. Within
the limits of the system , it can display objects
up to about 1000 feet (300 meters) away. The
heat image of a pedestrian detected by the
camera is shown in the instrument cluster dis­
play
Q fig . 104 . Warm areas appear lighter
and cold areas appear darker .
Pedestrian detection
Applies to vehicles: with n ig ht v ision ass istant
Fig. 105 Display : yellow pedestrian marking
Night vision assistant 103
Fig. 1 06 D isp lay: symbo l w hen infrare d image is not
visi ble
Night vision assistant can detect pedestrians
that are between about 50 and 300 feet (15
and 90 meters) in front of the vehicle, under
ideal conditions .
If a pedestrian is detected
when it is dark outside and the vehicle head­
lights are switched on, the pedestrian is high ­
lighted in yellow
Qf/g . 105, Qpage 104,
General information.
If another display such
as navigation replaces the image from the
night vision assistant, the symbo l~,, appears
in a tab
Q fig. 106.
(D Tips
If the night vision assistant image does
not appear when the system is sw itched
on, you can access it with the buttons on
the multifunction steering wheel
Q page25.

104 Night visi on assis tant
Pedestrian warning
Applies to vehicles: with night vision assistant
Fig. 107 Display : pedestrian warning
Fig . 108 D is p lay: pedestrian warning w ith a nother dis­
p lay
I f a pedestrian is detected in an area in front
of the vehicle that the system considers criti­
cal, the pedestrian is high lighted in red
¢ fig . 107 and a warning tone sounds. This
area is based on the vehicle speed and steer ­
ing angle. The pedestrian warning prompts
you to pay even closer attention to the area in
front of the vehicle and to watch out for pe­
destrians.
If another display s uch as the tr ip computer
replaces the image from the night vision as­
sistant, the indicator light turns red when
there is a pedestrian warning.¢
fig. 108 .
The pedestrian warning . appears in the
Head-up Display *.
(D Tips
The pedestrian marking and warn ing tone
can be adjusted in the MMI
!:!) page 105.
General information
Applies to vehicles: with night vision assistant
Fig. 109 Fro nt of th e ve hicle: night v ision assistant
camera
T he following situat ions may affect the func­
t ion of the n ight vision assistant system:
- poor visibility such as snow, rain, fog or
heavy road spray
- dirty lens on the n ight vis ion assistant cam -
era
Make sure the night vision assistant camera
¢
fig . 109 is not covered by stickers, deposits
or any other obstructions because that can
prevent the camera from working properly.
For information on cleaning the lens, refer to
¢ page 210.
Pedestrian detection depends on the d iffer ­
ence in temperature between the person and
the background. Pedestr ians may not be de­
tected if the temperature diffe rence is too
small . Th e pedestrian highl ighting feature is
deactivated at tempe ratures above 77 ° F
(25 °C) and when it is light outside.
A WARNING
Night vision assistant has limits and can­
not always detect pedestr ians. Always pay
close attention to traffic and the area
around your vehicle even when night vision
assistant is sw itched on .
- Night vision assistant can only warn
about people located within the visual
range of the infrared camera. The visual
range corresponds to the image in the in­
strument cluster display .
- Night vision assistant may not detect
-
peop le and highlight them if .,.

-they are not in an upright position, for
examp le if they are s itting, crouching
or lying down and/or
- if the outline in the display is incom­
p lete or interrupted, for example be­
cause the person is partially hidden by
a parked veh icle .
(D Tips
-Pedestrian detection and the pedestrian
warming are lim ited to objects that are
detected as pedestr ians. The system
does not detect animals . Even though
the shape and warmth radiated by each
object det ected is evaluated, the system
does have lim itations and it can give in­
correct warnings.
- Fo r techn ical reasons , the image pauses
in split second interva ls.
Switching on and off
Appl ies to vehicles: with night vision assistant
Fig . 110 Area a round the lig ht switch: night vis io n as ­
si st ant button
.. Switch the ignition on and turn the light
switch to the
AUTO position or io.
.. To switch night vision ass istant on, press the
~ button c::> fig. 110. T he image from the
night vision camera appears in the instru­
ment cluster d isp lay.
.. Press the button~ again to sw itch night vi ­
s ion assistant off .
Night vision assistant 105
Settings in the MMI
Applies to vehicles: with night vision assistant
Fig. 111 Disp lay : exa mple of pedest rian detect io n and
warn ing to n e sw it c hed off
.. Select: !CAR ! function button> (Car)* sys­
tems
control button > Driver assist > Night
vision assist.
Highlight pedestrians -
You can switch pedes­
trian detec tion
on and off. If you switch pe­
destrian detection off, the pedestrian warning
tone also switches off . The symbols
Ill and fa
appear in the upper right area of the instru­
ment cluster disp lay
¢ fig. 111.
Warning tone -You can switch the tone for
the pedestrian warning
on and off. When the
warning tone is sw itched off, a yellow symbol
for the deactivated warning tone with a line
through it appears in the upper right of the in­
strument cluster d isplay
c::>fig. 111 .
Contrast -When the night vision assistant is
switched on and the image is visib le in the in­
strument cluster display, you can adjust the
contrast in the image from
Min to Max .
Driver messages
Applies to vehicles: with night vision assistant
Night vision assistant: system malfunction!
The system cannot work properly and is
switched off. See your authorized Audi dealer
for assistance.
Night vision assistant: not available
The system cannot detect properly under cur­
rent conditions and is switched off temporari-
~ ~

106 Night vision assistant
Night vision assistant: only available in dark­
ness and with lights switched on
N ig ht vision assist ant only wo rk s when i t is
da rk ou tside and the headlig hts are o n.
Night vision assistant: pedestrian detection
not available
The system has deactivated the pedestrian de­
tec tion f unct ion.

Automatic Transmission
multitronic, S tronic,
tiptronic
Introduction
App lies to vehicles: with multit ro nic/S tronic/t ipt ronic
The automat ic transm iss ion is controlled elec­
tronically . The transmiss ion ups hifts or down­
shifts automatically depend ing o n which drive
p rog ram is se lect ed.
When a
moderate driving style is used, the
tra nsmission selects the most econom ica l
d riving mode .
It will then change up early and
de lay the downshifts to g ive bette r fu el econ­
omy.
The transmission switches to a sporty mode after a k ick- down or when the drive r uses a
sporty driving style ch aracte rized by quick ac­
celerator peda l movements, heavy ac celera­
tion, frequent ch anges in speed and traveling
at the maximum spee d.
I f desired, the drive r can a lso se lect the gears
manually ( tiptronic mode ) ¢ page 111.
Various automat ic transm issions may be in ­
stalled, depend ing o n the mode l:
multitronic transmi ssion
The mult itron ic transm ission is a continuously
variable transmission. Power is transferred us­ i n g a mu ltidisk clutch . In contrast to conven­
tional automat ic transm iss ions using shift ing
ope rations, the transmiss ion ratio in the con­
tinuously va riab le transm iss io n is changed
con tinuously. Th is op timi zes the com fort level
a nd co nserves fuel.
S tronic transmission
The S tronic is a dual -clutch transmission .
P owe r is transfe rred using two clutches that
wo rk ind ependen tly from one a nother. They
r e pl ace the tor qu e conve rter u sed in co nven­
tional a utoma tic transm iss io ns an d allow t he
ve hicl e to accelerate without a no ticeable in ­
ter ruption in traction.
Automatic Transmission 107
tiptronic transmission
In the tipt ronic t ra nsm issio n, p ower is trans ­
f erred by a to rque converter .
Selector lever positions
Applies to vehicles: wit h mult itronic/5 tro nic/tiptro nic
Fig . 1 12 Disp lay in th e inst rume nt cluster: selector
l ever pos itio n
The selector leve r pos ition engaged appears
next to the se lector lever as well as in the in­
strument cluster d isp lay.
P -Park
In this se lector lever posi tion the transm is­
s io n is mechanica lly locked. Engage P on ly
whe n the vehicle is
completely stopped¢&.
in Driving the automatic transmission on
page 110.
T o sh ift i n or out of posit io n P, you must first
press and ho ld the brake pedal and then press
the re lease b utton in the selector lever hand le
whi le moving the selector lever to or from P .
You can shift out of th is position only with the
ignition o n.
R -Reverse
Se lect R on ly when the vehicle is at a full stop
and the engine is running at idle speed¢ A in
Driving the automatic transmission on
page 110 .
Before you move the se lector lever to R, press
both the button in the hand le o f the selecto r
lever
and the brake pedal at the same t ime .
When the ignition is on, the backup lights illu­
m inate when the selecto r lever is moved into
R. .,.

108 Automatic Transmission
N - N eutr al
The transmission is in neutral in this position.
Shift to this position for stand ing with the
brakes applied
q .&. in Driving the automatic
transmission on page 11 O.
When the ve hicle is stationary o r at speeds
be low 1 mph (2 km/h), you must always apply
the footbrake befo re and while moving the
l ever out of N .
DIS -Normal position for driving forward
In the D/S position, the transmiss io n can be
operated e ither in the normal mode Dor i n
the sport mode S. To select the sport mode S,
pu ll the se lector lever back briefly . Pulling the
lever back aga in will select the normal mode
D. The instrument cluster display shows the
selected driving mode.
In the normal mode D, the transmission a uto ­
mat ica lly selects the suitab le gea r ratio.
It de­
pends on engine load, veh icle speed and driv­
ing style.
Select the sport mode S for sporty driving .
The vehicle makes fu ll u se of the engine's
power. Shifting may become noticeable when
accelerating.
When the ve hicle is stationary o r at speeds
be low 1 mph (2 km/h), you must always apply
the foot brake before and while moving the lever to D/S out of N .
A WARNING
Read and follow all WARNINGS q .&. in
Driving the automatic transmission on
page 110.
(D Note
-
Coast ing downh ill with the transmission in
N and the e ngine not r unning w ill result in
damage to the automatic transm iss io n
and possib ly the catalyt ic converter.
@ Tips
- Audi drive select : you ca n adj ust the
sporty s hift c haracte ristics in th e
Dy-
namic driving mode.Swi ll appea r in the
instrument cluster display instead of D.
-If you a cc iden tally selec t N whi le driving,
take your foot off the accelerato r pedal
immediately and wa it for the engine to
slow down to idle before select ing D/S.
- If there is a power fai lure, the selector
lever w ill not move out of the P position.
The emergency release can be used if
this happens
c::>page 113.
Automatic Shift Lock (ASL)
Applies to vehicles: with multitronic/5 tronic/tiptron ic
The Automatic Shift Lock safeguards you
against accidentally shifting into a forward or the reverse gear and causing the vehicle to
move unintentionally.
' ) ( )
Fig . 113 Shi ft gate: selector leve r lock pos it ions a nd
re lease button high lig h ted
The selector lever lock is re leased as follows:
.,. Tur n the ignition on .
.,. Step on the brake pedal.
At the same time
press and hold the re lease button on the
side of the gear selector knob
c:> fig . 113
with your thumb until you have moved the
selector lever to the desired posit ion.
Automatic selector leve r lo ck
The selector lever is locked in the P and N po­
s itions when the ignit ion is turned on . Yo u
must press the brake pedal and the re lease
button to select another position . As a re­
minder to the driver, the following warni ng
appea rs in the instrument clus ter display
whe n the selector is in P and N:
When stationary apply brake peda l while se-
lecting gear ..,_