ignition AUDI S7 2016 Owner's Guide

Driving
made a full brake application . ESC and the as·
soc iated components (ABS, ASR, EDL) cannot
overcome the laws of physics. In corners and
when road or weather conditions a re bad, a
full b rake app lication can cause the vehicle to
skid or the rea r end to break away, wh ich in·
c reases the risk of an acc ident.
Start-Stop-System
Description
Applies to vehicles: with Sta rt-Stop-System
The Start-Stop-System can he lp increase fue l
economy and red uce CO2 emissions.
I n Start -Stop mode, the eng ine shuts
off auto ­
matica lly w hen the vehicle is stopped, such as at
a traffic light. The ign ition remains sw itched on
during this stop phase . The engine w ill restart
automatically when needed .
The Start-Stop-System is automatically activated
each time you switch on the ignition.
Basic requirements for Start -Stop mode
- T he driver's door is closed.
- T he driver' seat be lt is lat ched .
- The hood is closed .
- The vehicle must have been dr iven faster than
2.5 mph (4 km/h) s ince the last stop.
- A trai ler is not hitched to the vehicle .
(D Note
Always switch the Start-Stop-System off when
driving through water <=>
page 80.
@ Tips
The engine stops shortly before the vehicle
comes to a stop
1>. The fu ll function of the
brake booster and the power steering is sti ll
available.
l l de pend ing on eng in e
80
Stopping/starting the engine
Applies to vehicles: with Start-Stop-System
Fi g. 8 4 Instrument cl uste r: en gin e stopped (stop phase)
.,. Brake the vehicle to a stop. The eng ine will be
sw itched
off shortly before the vehicle comes
to a standst ill or when the veh icle is station­
ary 1>. Keep your foot on the b rake peda l. The
[I] indi cato r light appears in the info rmat ion
line a t the bottom of the inst rument cl uster
disp lay. The needle in the tachometer a lso
moves into the READY positio n.
.,. The engine starts again when you take your
foot
off the brake peda l. The indicator light
turns
off.
Additional information
The engine stops in the P, N and D selector lever
pos itions.
If you se lect the R posit io n du ring a stop phase,
the e ngine will star t aga in .
Sh ift to P qu ickly to prevent the engine from
starting unintentionally when shift ing th rough R.
You can determine for yourself if the engine will
stop or not by reducing or increas ing the amount
of force you use to p ress the brake pedal. For ex­
ample, if yo u only lightly press on t he b rake ped­
al in s top-and and-go traffic o r when tur ning, the
engine w ill no t sw itch
off when the vehi cle is sta­
tiona ry . As soon as you press the b rake down
harder, the eng ine will sw itch
off.
(D Tips
- Press the bra ke peda l during a S top phase
to keep the vehi cle from rolling.

M N <( I.J "". rl 1.0
"' N 1.0 rl
-The ignition will turn off if you press the
I START ENGINE STOP I button during a stop
phase . The needle in the tachometer
moves
into the OFF position.
General information
Applies to vehi cles: with Start-Stop-System
The standard Start-Stop mode con be canceled
for different system-related reasons.
Fig. 85 Instrument cluster: Eng ine stop tempora rily un­
avai lable
Engine does not switch off
Before and during each stop phase, the system
checks if certain conditions have been met . For
examp le, the engine will not switch off in the fol­
lowing situations:
- The engine has not reached the minimum re­
quired temperature for Start-Stop mode.
- The interior temperature selected by the A/C
system has not been reached.
- The outside temperature is extremely high/low.
- The windshield is being defrosted@.
- The parking system* is be switched on .
- The battery charge level is too low .
- The steering wheel is turned at a sharp angle or
is moving .
- After engaging the reverse gear.
- On sharp inclines.
@J also appears in the instrument cluster dis­
play.
Engine automatically restarts
The standard Start-Stop mode will be canceled
during a stop phase in the following situations .
The engine restarts without any action by the driver.
Driving
- The vehicle rolls, for examp le while on a s lope.
- The interior temperature varies from the tem-
perature selected in the A/C system.
- The windshield is being defrosted@.
- The brake pedal is pressed severa l times in a
row.
- The battery charge level becomes too low.
- High power consumption.
The engine can turn off again when the condi­ tions for Start-Stop mode are met.
Ignition is switched off automatically
To prevent the battery from draining, the igni­
tion
will switch off automatically under the fol­
lowing conditions:
- The vehicle has already been driven.
- The Start-Stop-System has stopped the engine.
- The driver's door is opened .
- The driver's safety belt is removed.
- The brake pedal is not pressed down.
- The vehicle is stationary.
In this case, the activated low beam is replaced
by the parking light. The parking lights will
switch off after approximately 30 minutes or
when you lock the vehicle.
If the Start-Stop-System has not turned off the
engine or if you have switched the Start-Stop­
System off manually, the ignition will not be au­
tomatically switched off and the engine will con­
tinue to run
c> .&. .
A WARNING
--Never allow the engine to run in confined
spaces, because this increases the risk of as­
phyxiation .
@ Tips
-If you shift into the D or N position after
shifting into reverse, the vehicle must be
driven faster than 6 mph (10 km/h) in order
for the engine to switch off again .
81

Driving
(Canadian models) in the display will go out but
the saved speed remains the same .
Preselecting the speed
Applies to vehicles: with cruise control system
You con preselect your desired speed when the
vehicle is stationary.
.. Switc h the ignition on .
.. Pull t he lever in to position
(D q page 83,
fig . 87 .
.. To increase or decrease the speed, tap the lever
toward
0 10 .
.. To store the speed d isp layed, re lease the lever.
This f unction makes it possible, for example, to
save the speed you want before driving on the h ighway. Once on the highway, act ivate the cruise
control by pulling the lever toward
(D .
Switching the system off
Applies to vehicles: with cruise control
Temporary deactivation
.. Press the brake pedal, or
.. Press the lever i nto pos ition @ (not clicked into
place)
q page 83, fig . 87, o r
.. Drive for longer than S minutes at more than
5 mph (10 km/ h) above t he s to red speed .
Switching off completely
.. Press lever into position @(clicked into p lace),
o r
.. Swi tc h the ignition off .
The system reta ins the saved speed if you deacti­
vate the cruise control temporar ily. To resume
the saved speed, release the brake peda l and pull
the lever to position
(D .
Sw itching the ign ition off erases the saved speed .
A WARNING
You should only return to the saved speed if it
is not too fast for the current traffic cond i­
tions - risk of an accident !
84

Night visio n ass is t
- Night vision assist may not detect people or
wild animals and mark them if
- they are not in an upright position, for ex­
ample if they are sitt ing or ly in g down
and/or
- the silhouette in the display appears in­
comp lete or interrupted, for example be­
cause the person is pa rtially covere d by a
veh icle or an animal by tall grass. This
could increase the risk of an accident.
- Never try to swerve around an imals if do ing
so wi ll endanger you or other road users, be ­
cause this increases the risk of an acc ident.
- E ven though the system eva lu ates the
shape and hea t given off by all detec ted ob­
j ects, there are lim its to the system . There
may be false warnings .
- F or technica l reasons, the image pauses in
sp lit second interva ls.
Switching on/off
Applies to veh icles: w ith night vision assist
F ig. 11 5 Area arou nd t he ligh t switc h: n ig ht vis ion assist
butto n
Requirement : Switc h the ignition on and turn the
light switch to the
AUTO posit ion or .
.,. Press the~ button ¢
fig. 115. The heat image
from the night v is ion camera appears in the in­
strument cluster d isplay .
.,. Press the~ button again to sw itch night vision
ass ist off .
If cond it ions are br ight enough, night v ision as­
sist can be sw itched on without mov ing the light
switch to the
AUTO position . Pedestrian and w ild
106
anima l highl ighting and wa rnings are only active
whe n it is dark outside and the headlights are
switched on .
Adjusting the contrast
Applies to vehicles: with night vision assist
.,. Select: the I CARI function button > (Car )* Sy s­
tem s
control button > Driver ass istan ce >
Night vi sion ass ist contrast .
When the night vis ion assist is switched on and
the image is v is ible in the instrument cluster dis­
play, you can adjust the contrast in the image
from
Min to Ma x.
Driver messages
Applies to vehicles: with night vision assist
Night vision a ssis t: Sy stem fault
The system cannot guarantee cor rect function
and is switched off . See an authorized Audi dealer
or a uthorized Audi Service Facility for ass istance.
Night vis ion a ssist: Currentl y una vailable
The system cannot gua rantee cor rect function
temporar ily and is switched off .
Night vision a ssis t: Only available at night with
lights tu rned on
Night vision assist only works when it is da rk out­
s ide and the headlights a re on.
Night vi sion a ssi st: Ped estrian marking current­
l y unavailab le
The pedestrian and wild animal h ighlighting was
switched off by the system.

M N <( I.J "". rl I.O
"' N I.O rl
Automatic transmission S tronic, tiptronic
Introduction
The automat ic transm iss ion is controlled elec­
tronically. The transmission upshifts or down­
shifts automatically depending on which drive
program is selected.
When a
moderate driving style is used, the
transmission selects the most econom ical driving
mode. The transmiss ion upshifts at a lower RPM
and downshifts at a higher RPM to improve fuel
efficiency.
The transmission switches to a sporty mode after a kick-down or when the driver uses a
sporty driv­
ing style
cha racterized by quick accelerator pedal
movements, heavy acceleration, frequent
changes in speed and traveling at the maximum
speed.
If desired, the driver can also select the gears
manually (tiptronic mode) ¢ page 111.
Various automat ic tr ansm issions may be instal­
led, depending on the model:
S tronic transmission
The S tronic is a dual -clutch transmission . Power
is transferred using two clutches that work inde­
pendently from one another. They replace the
torque converter used in conventional automat ic
transmissions and a llow the vehicle to accelerate
without a noticeable interruption in traction.
tiptronic transmission
In the tiptronic transmission, power is transfer­
r ed by a torque converter.
Automatic transmission
Selector lever positions
Fig. 116 Disp lay in the instrument cluste r: selector lever
posit ion
T he selec tor lever pos ition engaged appea rs next
to the se lector lever as well as in the instrument
cluster display.
P -Park
In this selector lever position the transmission is
mechanica lly locked . Engage P only when the ve­
hicle is
completely stopped¢.& in Driving the
automatic transmission on page 109.
To shift in or out of posit ion P, you must first
press and hold the brake pedal and then press
the release button in the selector lever hand le
whi le moving the selector lever to or from P. You
can sh ift out of this position only with the igni ­
tion on.
R -Reverse
Select R only when the vehicle is at a full stop
and the engine is running at idle speed¢ .& in
Driving the automatic transmission on
page 109.
Before you move the selector lever to R, press
both the button in the hand le of the selector lev­
er
and the brake pedal at the same time.
When the ignition is on, the backup lights illumi­
nate when the selector lever is moved into R.
N -Neutral
The transm iss io n is in neutral in this pos ition.
Sh ift to this position for standing with the brakes
applied
¢ .& in Driving the automatic transmis-
sion on page 109. .,.
107

Automatic transmission
When the vehicle is stationary or at speeds below
1 mph (2 km/h), you must always apply the foot­
brake before and while moving the lever out of N.
DIS -Normal position for driving forward
In the D/S position, the transmission can be oper­
ated either in the normal mode Dor in the sport
mode S . To select the sport mode S, pull these­
lector lever back brief ly. Pulling the lever back
again will se lect the normal mode D . The inst ru­
ment cluster display shows the selected driving
mode.
In the
normal mode D , the transmission auto­
matically selects the suitable gear ratio . It de­
pends on engine load, vehicle speed and driving
style.
Select the
sport mode S for sporty driving. The
vehicle makes full use of the engine 's power .
Shifting may become noticeable when accelerat­
ing.
When the vehicle is stationary or at speeds below 1 mph (2 km/h), you must a lways apply the foot
brake before and while moving the lever to D/S
out of N.
A WARNING
Read and follow all WARNINGS¢.&. in Driv­
ing the automatic transmission on
page 109.
(D Note
Coast ing downh ill with the transmission in N
and the engine not running will result in dam­
age to the automatic transmission and possi­
bly the catalytic converter.
@ Tips
- Audi drive select: you can adjust the sporty
sh ift characte ristics in the
Dynamic driv ing
mode .Sw ill appear in the instrument clus­
ter display instead of D.
-If you accidentally select N while driving,
take you r foot off the accelerator pedal im­
mediately and wait for the engine to slow
down to idle before selecting D/S.
108
-If there is a power fai lure, the selector lever
wi ll not move out of the P position. The
emergency release can be used if this hap­
pens
¢ page 113.
Selector lever lock
The selector lever lock prevents you from select­
ing a gear accidentally, causing the vehicle to
roll .
Fig. 117 Selector lever lock
T o re lease the selector lever lock:
"' Switch the ignition on .
)
"' Press the brake pedal while pressing the inter-
lock button.
Automatic shift lock (ASL)
The selector lever is locked in the P and N posi­
tions when the ignition is switched on. The re­
move it from these positions, the driver must
press the brake pedal and press the lock button
at the same time. The following message ap­
pears in the instr ument cluste r display when the
selector lever is in the P or N position to rem ind
the driver:
Brake pedal must be applied to shift from P
The Automatic Shift Lock only functions when the
vehicle is stat ionary or at speeds below 1 mph
(2 km/h) . At speeds above about 1 mph (2 km/h)
the Automatic Sh ift Lock is automatically deacti­
vated in the N position .
The selector lever is not locked when shifting
quickly through N, for example from R to D. This
makes it poss ible to free the vehicle when it is
stuck by "ro ckin g" it. The selector lever lock en-
gages if the leve r stays in the N position longer ..,.

M N <( I.J "". rl I.O
"' N I.O rl
Selector lever emergency release
If the vehicle's power supply fails, the selector lever can be released in an emergency.
Fig . 120 Front center co nsole: Selector leve r em ergency
re lease
• To reach the emergency release mechanism, re­
move the ashtray insert*.
• Loosen and remove the small cap in the ashtray
mount ¢ffg.120.
• You now have access to a pin. Using a screwdriv­
er or similar object, press the pin down and
hold it in that position.
• Press the release button in the selector lever
and move it into the N position.
Only move the selector lever out of the P position
when the ignition is switched on. If the vehicle
must be pushed or towed due to a power failure
(for example, the battery is dead), the selector
lever must first be moved to the N position using
the emergency release mechanism .
Automatic transmission
113

M N <( I.J "". rl I.O
"' N I.O rl
Parking system plus
Description
Applies to vehicles: with parking system plus
Audi parking system plus provides audio and vis­
ual signals when parking.
Fig . 121 Di sp lay fie ld
Sensors are located in the front and rear bump­
ers. If these detect an obstacle, visual and in
some situations audible signals warn you.
Make sure the sensors are not covered by stick­
ers, deposits or any other obstructions as it may
impair the sensor function. For information on
cleaning, refer to¢
page 205.
The display field begins approximate ly at :
® 4 ft (1.20 m)
® 3 ft (0.90 m)
© 5.2 ft (1.60 m)
@ 3 ft (0.90 m)
The closer you get to the obstacle, the shorter
the interval between the audible signals. A con­
tinuous tone sounds when the obstacle is less
than approximately 1 ft (0.30 m) away. Do not
continue driv ing farther ¢&.
in General informa ­
tion on page 114,
~ 0 in General information on
page 114!
If the distance to an obstacle remains constant,
the volume of the distance warning gradually
drops after about four seconds (this does not ap­
p~ in the continuous tone rang~.
Parking systems
Switching on/off
Applies to vehicles: with parking system plus
Fig. 122 Cente r co n sole : pa rking a id b utton
Switching on
.. Shift into reverse, or
.. Press the
Pw.a button in the center console
¢
fig . 122 . A short confirmation tone sounds
and the LED in the button turns on .
Switching off
.. Drive faster than 6 mph (10 km/h), or
.. press the
Pw.a button, or
.. Switch the ignition off.
Visual display
The segments in front of and behind the vehicle
help you to determine the distance between you
and an obstacle . The red lines* mark the expect­
ed direction of travel according to the steering
angle . A white segment indicates an identified
obstacle that is outside of the vehicle's path . Red
segments show identified obstacles that are in
you r vehicle 's path . As your vehicle comes closer
to the obstacle, the segments move closer to the
vehicle . Th e coll is ion area has been reached when
the next to last segment is displayed. Obstacles
in the collision area, including those outside of
the vehicle's path, are shown in red. Do not con­
tinue driving forward or in reverse ¢&.
in Gener­
al information on page 114,
¢ (i) in General in­
formation on page 114!
115

M N <( I.J "". rl I.O
"' N I.O rl
-The camera lens en larges and distorts the
field of v ision. The object appears both a l­
tered and inaccurate on the screen.
- In certain situations, peop le or objects in
the display appear closer or farther away:
- For objects that do not touch the ground, such as the bumper of a parked vehicle, a
trailer h itch or the rear of a tru ck . Do no t
use the help lines in this case .
- I f driven from a leve l surface onto a n in ­
cline, or a downward s lope .
- I f driven toward p rotruding objects.
- I f the ve hicle is ca rrying too much load in
the rear.
(D Note
- Always read and follow the applicable warn­
i ngs
c:> © in General information on
page 114 .
-The orange colored orientat ion lines in the
Infotainment d isplay show the vehicle path
depend ing on the steering wh eel angl e. The
fron t of the vehicle fro nt swi ngs out more
th an the rear of the vehicle. Maintain plenty
of distance so that your outside mi rror or a
corner of you r vehicle does not collide with
any obstacles .
Switching on/off
Applies to vehicles: with rearview camera
Sw itching on
.,. Shift into reverse, or
.,. Press the
PwA button in the center console
c:> page 115, fig. 122. A short confirmation
tone sounds and the LED in the button turns
on .
Sw itching b etwe en the r ear view camer a and
optical di splay
.,. Press the Graphic control button®
c:, page 117, fig. 12 7 to see the opt ica l display .
.,. Press the
Rear view cont ro l button to see the
rearview camera image.
Sw itching off
.,. Drive forward faster than 10 km/h, or
.,. press the
P,1
1! button, or
P arking systems
.,. Switch the ignition off .
@ Tips
- The visua l display in the left pa rt of the dis­
play shou ld help you detect the crit ica l vehi­
cle a reas .
- Yo u can change the vo lume and pi tch of the
signa ls as well as the display
c:, page 124.
Cross parking
Appl ies to vehicles : wit h rearv iew camera
This view may be used when parking in a garage
or in a parking space .
Fig . 127 In fotainment: aiming at a parking spot
F ig . 12 8 Infota inment: align ing the vehicle
.,. Turn the Infotainment on and shift into reverse
gear.
.,. The orange colored orientation lines
(D show
the direction of travel of the vehicle. Turn the steering whee l until the orange or ientation
lines appea r in the pa rking space
c:> fig. 127 .
Use the markings @to help you estimate the
d istance from an obsta cle. Each marking repre­
sents approximate ly 3 ft (1 m). The blue area
represen ts an extension of the vehicle 's o utline
by app rox ima tely 16 ft (5 meters) to the rear. ..,
117

Parking systems
passenger's door/luggage compartment lid
was opened.
Switching on or off
Applies to veh icles: with pe riphera l cameras
F ig . 132 Center console: Button P<IA
Fig. 133 Infotainment: Selecting the mode
Switching on
• Sh ift into reverse, or
• Press the P
1#! button in the center console
9 fig. 132. A short confirmation tone sounds
and the LED in the button turns on.
Selecting the mode
• Turn the control knob to the symbol for the de­
sired mode @through
© 9 fig. 133 and press
the control knob.
Switching off
• Drive forward faster than 10 km/h, or
• press the
P'#A button, or
• Switch the ignition off.
You may select from the follow ing modes:
@ -peripheral
9 page 120
ll Th e ca mera image is not show n for all versions.
120
® -corner view (front) 9 page 121
©-front 9page 121
@ -rear 9 page 121
©-corner view (rear) ¢ page 121
Peripheral
App lies to vehicles : wit h peripheral ca meras
Fig. 134 Infotainment: peripheral mode
This view is ideal for maneuvering. The veh icle
surroundings are shown using the came ra im­
ages . The vehicle image is shown by the system .
Selecting peripheral
• Select the@symbo l w ith the control knob and
press the control knob.
Switching between optical view and camera
image
1>
• Press the Graphic @ control button to see the
optical display.
• To display the camera image, press the
Camera
control button.