check engine AUDI TT 2013 Owner´s Manual

188 Checking and filling
Before you check anything in the engine com­
partment,
alwa ys r ea d and heed all WARN­
INGS ¢ A in Working in the engine compart­
ment on page 180.
• Park your vehicle on a level surface.
• Switch the ignition off.
• Read the coolant level at the coolant expan­
s ion tank ¢
page 182, fig . 134. With a cold
engine, it must be above the "min" mark .
With a hot engine, it ca n be a little above
the indicated range .
The location of the coolant expans ion tank
can be seen in the engine compartment illus­
tration
¢ page 182.
To obtain an accurate read ing, the engine
must be switched off.
The expansion tank in yo ur vehicle is equipped
with an e lectric coolant level sensor .
When the coo lant level is too low, the warning
light in the A uto- Check System ¢
page 16 will
illuminate until yo u add coo lant and the level
has been restored to normal. Even though
there is an electric coo lant level sensor, we
still recommend you check the coolant leve l
from time to time .
Coolant loss
Coolant loss may indicate a leak in the cooling
system . In the event of coolant loss, the cool­
ing system should be inspected immediately
by your author ized Audi dealer. It is not
enough merely to add coolant .
In a
sealed system, losses can occur only if
the boiling point of the coolant is exceeded as
a result of overheat ing.
(D Note
Do not add any type of radiator lea k seal­
ant to your vehicle's eng ine coolant. Add­
ing radiator repair f luid may adversely af­
fect the function and performance of your
cooling system and could res ult in damage
not covered by your New Vehicle Limited
Warranty.
Adding coolant
Be very careful when adding engine coolant.
Before you check anyth ing in the engine com­
partment,
always read and heed all WARN­
INGS ¢ A in Working in the engine compart­
ment on page 180 .
• Turn off the engine.
• Let the engine cool down.
• Place a thick rag over t he coo lant expansion
tank
¢ page 187, fig . 138 a nd carefully
tw ist the cap counter-clockwise ¢&_ .
• Add coo la nt.
• Twis t the cap on aga in
t ightly.
Replacement engine coolant must conform to
exact spec ificat ions ¢
page 18 7, Coolant.
Even in a n emerge ncy, if coolant add i-
t ive G1 2++, G12+ or G12 is not ava ilable , do
not use a d iffe ren t addit ive. Use plain water
instead unti l you can get the cor rect additive
and can restore the correct ratio . This sho uld
be done as soon as possible .
If you have los t a considerab le amount o f
coolant , then you sho uld add cold ant ifreeze
and co ld wate r on ly w hen the engine is cold.
Alw ays use
new engine coo la nt whe n refilling .
Do not fill coola nt above the "MAX" mark. Ex­
cess coola nt wi ll be fo rced o ut through the
pressure relief valve in t he cap w hen the en­
gine becomes hot.
,&. WARNING ~ -
- T he cooling system is under pressure and
can get very hot. Reduce the risk of
scalding from hot coolant by followi ng
these steps.
- T urn off the engine and allow it to coo l
down.
- Protect yo ur face, hands and arms from
escaping fluid and steam by covering
the cap w ith a large, t hick rag.
- T urn the cap s lowly a nd ve ry carefully
in a counter-clo ckwise direction while
applying light, downward pres sure on
the top of the cap.

-To avoid being burned, do not spill an­
tifreeze or coolant on the exhaust sys­ tem or hot engine parts. Under certain
conditions, the ethylene glycol in en­
gine coolant can catch fire.
- Antifreeze is poisonous. Always store an­
tifreeze in its original container and well out of the reach of children.
- If you drain the coolant, it must be
caught and safely stored in a proper con­
tainer clearly marked "poison".
(D Note
- Coolant pollutes the environment and
could cause an engine fire. Excess cool­
ant will be forced out through the pres­
sure relief valve in the cap when the en­
gine becomes hot.
- If, in an emergency, only water can be
added, the correct ratio between water
and antifreeze¢
page 187 must be re­
stored as soon as possible.
@ For the sake of the environment
Drained coolant should not be reused. Al­
ways dispose of used coolant while observ­ ing all environmental regulations.
Radiator fan
The radiator fan switches on automatically by
itself
The electric radiator fan is controlled by ther­
moswitches that switch on and off depending
on coolant and engine compartment tempera­
tures.
An auxiliary electric radiator fan* switches on
and off depending on coolant temperature
and other vehicle operation conditions.
After you switch the engine off, the auxiliary
fan can continue running for up to 10 minutes
- even with the ignition off.
It can even switch
on again later by itself
c::> &., , if
- the temperature of the engine coolant rises due to the heat build-up from the engine in
the engine compartment, or
Checking and filling 189
- the engine compartment heats up because
the vehicle is parked in intense sunlight.
A WARNING
-To reduce the risk of personal injury nev­
er touch the radiator fan .
- The auxiliary electric fan is temperature
controlled and can switch on suddenly
even when the engine is not running.
- The auxiliary radiator fan switches on au­
tomatically when the engine coolant
reaches a certain temperature and will
continue to run until the coolant temper­
ature drops.
Brake fluid
Checking brake fluid level
The brake fluid level can be checked with a
quick glance.
Fig. 139 Engin e compart ment: cover on th e br ake fluid
re se rvoir
Before you check anything in the engine com­
partment,
always read and heed all WARN­
INGS c::> .&. in Working in the engine compart­
ment on page 180.
~ Read the brake fluid level from the brake
fluid reservoir
c::> page 182, fig. 134 . The
brake fluid level must be between the "MIN"
and "MAX" markings.
The brake fluid reservoir is located behind the
rear partition of the engine compartment on
the left side
c::> page 182.
The fluid level may drop slightly after some
time due to the automatic adjustment of the brake pads. This is not cause for alarm.
i,,.

192 Checking and filling
Working on the battery
Be especially careful when working on or near
the battery!
The battery is located in the luggage compart­
ment under the floor. Before you work on or
near the battery,
read and heed all WARN­
INGS ~.&. -
Always heed the safety warnings, when work­
ing on the vehicle battery or the vehicle elec ­
tr ical system to prevent injury .
The following WARNINGS are very
important when working on the battery:
Always heed the following WARNING SYM· BOLS and safety precautions when working
on the battery.
@ Always wear eye protection .
b,. Battery acid contains sulfuric acid. Al­
~ ways wear gloves and eye protection.
~~-
No
@ -sparks
-flames
-smoking.
When a battery is charged , it produces
hyd rogen gas which is explosive and
could cause personal injury.
I ~ Always keep the battery well out of
V;!J/ reach of children .
A WARNING
=
Whenever working on the battery or on
the electrical system, there is the risk of
injury, accident and even fire. Read and
heed the following WARNINGS:
- Always wear eye protection. Do not let
battery acid or any lead particles get on
your sk in or cloth ing. Sh ield your eyes.
Explosive gases can cause blindness or
other injury .
- Battery acid contains sulfur ic acid. Sulfu­
ric acid can cause blindness and severe
burns.
- Always wear gloves and eye protection.
Do not tilt the battery because ac id
-
could leak out of the ventilation open­
ings.
- If you get battery acid in your eyes or
on your skin, immediately rinse with cold water for several minutes and get
med ical attention.
- If you shou ld ingest any battery acid,
seek medical attention immediately.
- Do not expose the battery to an open
flame, e lectr ic sparks or an open light.
- Do not smoke .
- Do not interchange the positive and neg -
ative cables .
- When working on the battery, be sure
not to short-circuit the terminals with
too ls or othe r metal objects . This would
cause the battery to heat up very quickly,
which could lead to damage or explosion
and personal injury.
- When a battery is charged, it produces
hydrogen gas which is explosive and
could cause personal injury.
- Always keep the battery well out of the
reach of children.
- Before work is done on the electrical sys­ tem, disconnect the negat ive ground ca­
ble.
- Before performing any work on the e lec­
tr ical system, switch off the engine and
ignit ion as well as any electrical equip­
ment. The negative cable on the battery
must be disconnected .
If you are just go­
ing to replace a light bulb, then it is
enough to switch off the lights.
- Before disconnecting the battery, switch
off the anti-theft alarm system! Other­
wise you will set off the alarm.
- When disconnecting the battery, first disconnect the negative cable and then
the positive cab le .
- Before reconnecting the battery, make
sure all electr ica l consumers are switch­
ed off . Reconnect the positive cable first
and then the negative cable. Never inter­
change the cables - this could start a fire!
- Never charge a frozen or a thawed-out
battery. It could exp lode! If a battery has
frozen, then it must be replaced. A
llll-

dischar ged battery can freeze over at
32 °F (0 °C).
- Make sure the vent hose is alw ays attach­
ed to the opening on the side of the bat­
tery.
- Never use batteries which are damaged .
Danger of explosion! A lways rep lace a
damaged battery.
A WARNING
California Propos ition 65 Warning:
- Battery posts, terminals and related ac­
cessories contain lead and lead com­ pounds , chemicals known to the State of
Californ ia to cause cancer and reproduc ­
t ive p roblems. Wash ha nds after han­
dling .
CD Note
-Do not d isconnect the vehicle battery
when the ignition is switched on or when
t h e engine is running, otherwise, you will
damage e lectronic components in the
ele ctr ical sy stem.
-If your vehicle is goi ng to stand for a
l ong pe riod of time wit ho ut being d riven,
p rotec t the battery from "freezing ", o th­
erwise it will be d amaged and w ill t hen
h ave to be replaced.
Checking the battery acid level on magic
eye batteries*
Th e battery acid level in the batt ery can be
checked through the clear inspection window.
F ig. 140 Lu ggag e co mpart ment : Bat te ry w it h m agi c
eye.
Checkin g and fillin g 193
On top o f the battery , there is a round "win ­
dow" . This window (magic eye) changes co lor
as the battery charge and ac id leve l change .
.. Read and heed all WARN INGS
c::> .&_ in
Working on the battery on page 192
.. Read the acid level from the window on the
battery c:>fig .140.
Air bubb les in the window can cause an inac ­
cu rate reading. Carefu lly tap on the s ide of
t h e window .
- If the window is green , the batte ry acid level
is cor rect .
- If the w indow h as
no color or is bright yel­
low ,
the batte ry a cid level is too low. Have
the ba ttery tested by your authori zed Audi
dea ler or a qua lified workshop .
- If the window is black , then the ba ttery is
insufficiently charged. Recharge the battery
as soon as possib le
c::> page 193.
CD Note
Do not overfill the bat tery, otherwise b at­
tery ac id will ove rflow through the vent
ope ning . This ca n damage the paint and
cause corrosion .
Charging of battery
Starting the engine requires a well charged
battery.
.. Alway s read and heed all WARNINGS be ­
low
c::> .&. and c::> .&. in Working on the bat­
tery on page 192 .
.. Switch off the ignition and a ll electr ical con­
sumers .
.. Make sure the area is well ven tilated when
you cha rge the battery .
.. Connect charger cables.
ALWAYS conne ct
charger cable s POSITIVE
G) to POSITIVE
G) ; NEGATIVE Oto NEGATIVE Q .
.. Swit ch o n the charge r .
.. Tu rn off the charger
c::> .&_ .
.. Disconnect the charger cab les.
.. Connect both battery cab les to the battery
if necessary -
first plus, then minus. II>-

194 Checking and filling
When charging at low voltages (e.g . w ith a
tri ckle charger ), the battery cables do not
have to be d isconnected first. Be fore charging
at
high voltages, i.e. " fast charging ", you
must disconnect both cables. In e ither case,
follow the instruct ions from the ma nufacturer
of the charger .
Fastcharging a battery is
dangerous c:> .&. in
Working on the battery on page 192 .
It re­
qu ires specia l charg ing equipment a nd the
k nowledge to go wi th it. We recomme nd hav­
ing your battery fast charged on ly by a quali­
fied workshop.
A discharged batte ry can
freeze at tempera­
tures of on ly 32 °F (0
°(). A llow a frozen bat­
tery to thaw completely befo re attempt ing to
cha rge it
c:> ,&. . Howeve r, we re comme nd not
usi ng a thawe d batt ery again bec ause t he bat­
tery cas ing ca n be cracked d ue to ice forma ­
tion and can lea k bat tery aci d.
D o not open the batte ry caps whe n charg ing
the ba ttery.
_&. WARNING
-
Cha rging a batte ry can be dange rous.
- N ever charge a fro zen b att ery .
It may ex­
plode beca use o f gas t rappe d in t he i ce.
Allow a frozen battery to thaw o ut first .
- D o no t reu se batte ries which we re fr o­
zen . The batte ry housing m ay h ave
c rac ked an d weakened whe n the battery
froze .
- C harge the b attery in a we ll ven tilated
area . Kee p away from open flame o r elec­
trical spa rk. Do not smoke. Hydrogen gas
generated by the battery is exp losive.
- To reduce the danger o f explosion, never
co nnect or disconnect charger cables
wh ile the charger is operating .
- Fast charg ing a battery is dangerous and
shou ld on ly be attempted by a compe­
tent technician w ith the proper eq uip­
me nt.
- Battery acid that may spill d uring charg­
ing should be washed
off wit h a so lution
of warm water and baki ng soda to neu ­
t raliz e the aci d.
(D Note
Neve r use a fast charger as a booster to
start the eng ine. Th is w ill seriously dam­
age sensit ive e lectronic components, such
as cont ro l units, re lays, radio, etc. , as well
as the battery charge r.
(D Tips
The vehicle batte ry must not be charged
with a standard small charger that plugs in to the c igarette lighter or outlet.
Windshield/headlight
washer container
Fi g. 141 Fen der, left: cove r o n th e w inds hield a nd
h ead lig ht• wa sher fl uid re se rvoir
T he was her fluid co nta iner is mar ked w it h the
symbol
Q o n its c a p<=> page 182, fig . 134.
""' Before yo u check anything in the engine
compa rtme nt,
always read and heed all
WARNINGS c:> ..&. in Wor king in the engine
c ompartment on page 18 0.
""' Lift th e fill er ca p tongue to ad d washer flu­
id . You can f ill the containe r to the top .
""' Press the cap back o nto the fi ller neck after
fi lling the container.
You can find the reservo ir
capacity in t he table
in
<=> page 24 0
Clean wa ter should be used when filling up. If
poss ible, use so ft wat er to preven t sc aling o n
t h e washer jets . A lways ad d a glass clea ner
solution (with frost protection in the winter) . ..,.

(D Note
-Do not mix engine coolant antifreeze or
any other additives to fill up the
windsh ield washer rese rvoir.
- Do not use glass cleane rs contain ing
paint solvent; you r isk damaging the
paint.
Checkin g and fillin g 195
•
•

228 Fuses and bulbs
Fuses and bulbs
Electrical fuses
Replacing fuses
Fuses that have blown will have metal strips
that have burned through .
Fig. 164 End face of instrument panel: rem ov ing cover
p la te to access fuses
Fig. 165 Left side of eng ine compart men t: fuse cove r
Fuse cover on the left end face of the
inst rument pane l
.. Switch off the ignition and the electrical
component affected.
.. Carefully pry the fuse cover off the instru ­
ment panel using the ignition key or a
screwdriver~
fig. 164 .
.. Check the fuse listing on the next pages to
find out which fuse belongs to the compo­
nent which has failed
~ page 229, Fuse Lo­
cation, Instrument Panel left .
.. Remove the blown fuse with the plastic clip
provided. The cl ip is located on the holder in
the fuse box .
.. Replace a blown fuse (recognizable by the
melted metal str ip inside) with a fuse of the
same amperage .
.. Firmly snap the cover back onto the instru­
ment panel face .
Fuse cover in engine compartment
.. Switch the ignition and the affected con­
sumer off .
.. Unlatch the fuse cover, push the two slides
forward
~ fig. 165.
.. Find out which fuse belongs to the equip­
ment which stopped working~
page 230,
Fuse location , le~ side of engine compart­
ment .
.. Remove the plastic from its retainer in the
fuse box cover (left face end of the instru­
ment panel), place it on the fu se in question
and pull it out .
.. If the fuse is burned out (recognizable by
melted strips of metal), replace it with a
new fuse
of the same rating.
.. Replace the fuse cover.
.. Push the two slides to the rear~
fig. 165.
Install the fuse cover carefully to prevent
water from enter ing .
The various electrical circuits are protected by
fuses. The fuses are clustered in a centralized unit. The unit is located behind the face panel
at the end of the instrument panel.
You are well advised to keep a supply of spare
fuses in your vehicle. Fuses with the proper
ampere rat ings are ava ilable at your author ­
ized Audi dealer.
A WARNING -
Do not repa ir fuses and never replace a
blown fuse with one that has a higher amp
rating. This can cause damage to the elec­
trica l system and a fire.
(D Note
If a new fuse burns out again after shortly
have you have installed it, have the electri­
ca l system checked by your authorized
Audi dealer.

232 Emergency situations
Emergency situations
General
This chapter is intended for trained emer­
gency crews and working personnel who
have the necessary tools and equ ipment to
perform these ope rations.
Starting by pushing or
towing
Q;) Note
Vehicle s with an automati c transmission
cannot be started by pushing or towing .
Starting with jumper
cables
If necessary, the engine can be started by
connecting it to the battery of another vehi­
cle.
If the engine should fail to start because of a
discha rged or wea k batte ry, the battery can be
connected to the battery o f
another vehicle,
using a
pair of jumper cables to start the en­
g ine .
Jumper cables
Use only jumper cab les of sufficiently
large cross section to safely carry the starter
cur rent. Refer to the manufacturer's specifica­
ti ons.
Use on ly jumper cables which have
insulated
termina l clamps and are properly marked for
d istinction :
plus(+) cable in most cases colo red red
minu s(-) cable
in most cases colo red black .
_& WARNING
Batterie s contain elec trici ty, a cid, and ga s.
Any of th ese c an cause ve ry seri ous or f ata l
inju ry . Follow the instructions below fo r
safe han dling of your ve hicle's battery.
- Alw ays s hield yo ur eyes and avoid lean ­
ing over the batte ry w henever possib le . -
A discharged battery can a lready freeze
at temperatures just be low 32 °F (0 °C).
Before connect ing a jumper cab le, the
frozen battery must be thawed com­
p letely, othe rwise it cou ld explode .
- Do not allow batte ry acid to contact eyes
or skin . Fl ush any contacted a rea wi th
water immediat ely .
- Imp roper use of a booster battery to
s tart a vehicle may cause an explosion.
- Vehicle batter ies generate explosive gas­
es . Keep sparks, flame and lighted ciga­
rettes away from ba tte ries .
- Do not try to jump start a ny ve hicle w ith
a low ac id leve l in the battery .
- The vo ltage of the booster batte ry m ust
a lso have a 12-Vo lt rat ing . The capacity
(A h) of the booster batte ry should not b e
lowe r than that of the discharged bat­
tery . U se o f batt erie s of d iffe ren t voltage
or subs tanti ally diffe ren t "Ah" rat ing
may c ause an exp losion and person al in­
ju ry .
- N ever ch arge a fr ozen bat te ry. Gas t rap ­
ped in the ice may ca use an ex plosion .
- N ever ch arge o r use a batt ery th at has
been fro zen. T he battery case may have
be weakened.
- Us e of batt erie s of di ffere nt vo lta ge or
substan tially differen t ca pa city (Ah) rat ­
i ng may cause an exp losion and injury.
T he capac ity (Ah) of the booster battery
should not be lower than that of the dis­
charged batte ry.
- Before you check anything in the engine
compartment, always read and heed a ll
W ARNI NGS
c::;,page 174, Engine com­
partment .
@ Note
-App lying a hig her voltage booster ba t­
tery will cause expens ive damage to se n­
sitive electronic components, such as
cont ro l units , relays, rad io, etc.
- There must be no electrical contact be­
twee n the vehicles as otherwise current
cou ld already start to flow as soo n as th e
posi tive (+) term inals are connect ed. ""

234 Emergency sit uat ions
_& WARNING
To avo id serious per sonal injury and dam­
age to the vehicle, heed all warnings and
instructions of the jumper cable manufac­
turer. If in doubt, call for road serv ice.
- Jumper cables must be long enough so
that the vehicles do not touch.
- When connecting jumper cables, make
surethattheycannotgetca ughtinany
moving parts in the eng ine compart­
ment.
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS
c::> page 174, Engine com­
partment.
(D Note
Improper hook-up of jumper cables can ru ­
in the generator.
- Always connect POSITIVE( +) to POSI­
TIVE(+), and NEGATIVE(-) to NEGATIVE ( - ) ground post of the battery manager
control unit.
- Check that all screw plugs on the battery
ce lls are screwed in firmly. If not, tighten
plugs prior to connecting clamp on nega­
tive battery terminal.
- Please note that the procedure for con­
nect ing a jumper cable as described
above applies spec ifically to the case of
you r vehicle be ing jump started. When
you are giving a jump star t to a nothe r ve­
hicle, do
not connect the negat ive (-) ca­
ble to the negat ive (-) term inal on the
discharged battery @. Instea d, secure ly
connect the negative (-) cable to either a
solid metal component that is firmly
bo lted to the engine block or to the en­
gine block itself. If the battery that is be­ i ng charged does not vent to the outside,
escap ing batte ry gas cou ld ign ite and ex­
plode!
-
Emergency towing
with commercial tow
truck
General hints
Your Audi requires special handling for tow­
ing.
T he following information is to be used by
commercial tow truck operators who know
how to operate their equipment safely.
- Ne ver tow your Audi , towing will cau se
damage to the engine and tr an smi ssion .
- Ne ver wrap th e safet y chain s or winch ca­
ble s ar ound the brak e lines.
- To prevent unne ces sary damage , your Audi
must be tran sp o rt ed with a car carrier
(flatbed truck ).
- To load th e vehi cle on t o the flat bed , u se
the t owing loop found in the vehicle tool s
and attach to the front o r rear anchorage
c::> page 235 and c::> page 236.
A WARNING
--A vehicle being towed is not safe for pas­
sengers. Never allow anyone to ride in a
vehicle be ing towed, for any reason.

Lifting vehicle
lifting with workshop hoist and with
floor jack
The vehicle may only be lift ed at the lifting
poin ts illustra ted.
F ig. 177 Rear lift ing point (r ig ht side)
Fi g. 178 Front lift ing po int frig h t side)
• Rea d and h eed WARN ING c:::> A-
• Locate lifting points c:::> fi g. 177 c:::> fig. 178 .
• Adjust lift ing arms o f wor kshop hoist or
f loor jac k to match vehicle lifting points.
• Inse rt a r ubber pad between the floor jac k/
workshop hoist a nd the lifti ng points.
If you must lift your vehicle with a floor jack
to work underneath, be sure the vehicle is safely supported on stands intended for this
purpose.
Front lifting point
The lifting point is locate d on the f loor pan re­
info rcement about at the same level as the
jack mounting point
c:::> fig. 178. Do not lift
the vehicle at the vertical sill reinforcement .
Rear lifting point
The lifting poi nt is locate d on t he vertical rein­
forcement of the lower sill for t he on boa rd
jack
c:::> fig. 177.
Emergency situations 237
lifting with vehicle jack
Re fer to c:::> page 225 .
_&. WARNING
-To re duce t he risk of ser ious injury an d
ve hicl e damage.
- Alwa ys lift the veh icl e only at the spe­
c ial w orkshop hoist and floor jack lift
p oin ts ill ust rated
c:::> fig. 177 and
c:::> fig. 178 .
-Fa il u re to Lift th e ve hicl e at th ese
p o ints co uld cau se the ve hi cle to til t or
f all from a lift if th ere i s a cha nge in ve­
h icl e weigh t distr ibu tion and balan ce.
This mi ght h app en, fo r ex am ple, whe n
h eavy co mpon ent s such as the eng ine
b lock o r transmission are remove d.
- Wh en removin g hea vy componen ts li ke
these, anchor vehicle to h oist or ad d cor ­
respo nding wei ghts to ma intain t he ce n­
ter of gravity. Ot herwis e, th e ve hicle
might tilt or slip off the ho ist, caus ing
serio us pe rso nal i nju ry.
CI) Note
-Be aware of the following points before
lifting the vehicle:
- The vehicle should never be lifted or
jacked up from underneath the engine
oil pan, the transmission housing, the
front or rear axle or the body side
members. This could lead to seriou s
damage.
- To avoid damage to the underbody or
chassis frame, a rubber pad must be inserted between the floor jack and
the lift points.
- Before driving over a workshop hoist ,
check that the vehicle weight does not
exceed the permissible lifting capacity
of the hoist.
- Before driving over a workshop hoist ,
ensure that there is sufficient clear­
ance between the hoist and low parts
of the vehicle.
-