BMW 4 SERIES COUPE 2017 Workshop Manual

Overview
Tilting
the
glass
sunroofPush switch briefly upward.
'yThe closed glass sunroof
tilts.'yThe opened glass sunroof
closes until it is in the tilted
position. The sliding visor
does not move.
Opening/closing
the
glass
sunroof
and
sliding
visor
together
'yPress the switch in the dej
sired direction to the resistj
ance point and hold it there.
Glass sunroof and sliding vij
sor open together while the
switch is being held.
The glass sunroof closes
while the switch is being
held. The sliding visor can
be manually closed.'yPress the switch in the desired direction
past the resistance point.
The glass sunroof and sliding visor open
automatically.
The glass sunroof closes automatically.
The sliding visor can be manually closed.
Pressing the switch upward stops the moj
tion.
Convenient opening via the remote control, rej
fer to page 35.
Closing by means of Comfort Access, refer to
page 38.
Comfort
position
If the glass sunroof is not completely opened
automatically, the comfort position has been attained. In this position the wind noises in theinterior are the least.
If desired, continue the movement by pressing
the switch.
Jam
protection
system
General
information
If the closing force when closing the glass sunj
roof exceeds a certain value, the closing movej ment is stopped, beginning at approximately
the middle of the opening in the roof, or from
the tilted position during closing. The glass
sunroof opens slightly.
Closing
from
the
open
position
without
jam
protection
If there is an external danger, proceed as folj
lows:1.Push the switch forward past the resistj
ance point and hold.
The glass sunroof closes with limited jam protection . If the closing force exceeds aspecific threshold, closing is interrupted.2.Push the switch forward again past the rej
sistance point and hold until the glass sunj
roof closes without jam protection . Make sure that the closing area is clear.Seite 51Opening
and
closingControls51
Online Edition for Part no. 01 40 2 974 422 - X/16

Closing
from
the
raised
position
without
jam
protection
If there is an external danger,
push the switch forward past the
resistance point and hold it.
The glass sunroof closes withj
out jam protection .
Initializing
after
a
power
interruption General
information
After a power failure during the opening or closing process, the glass sunroof can only be
operated to a limited extent.
The system can be initialized under the followj
ing conditions.'yThe vehicle is parked in a horizontal posij
tion.'yThe engine is running.'yThe external temperature is above
41 

SettingsVehicle
features
and
options
This chapter describes all standard, country- specific and optional features offered with theseries. It also describes features that are notnecessarily available in your vehicle, e. g., due
to the selected options or country versions.
This also applies to safety-related functions
and systems. When using these functions and systems, the applicable laws and regulations
must be observed.
Sitting
safely
An ideal seating position that meets the needs
of the occupants can make a vital contribution to relaxed, fatigue-free driving.
In the event of an accident, the correct seating
position plays an important role. Additionally, observe the following chapters for safe driving:'ySafety belts, refer to page 57.'yHead restraints, refer to page 58.'yAirbags, refer to page 105.
Seats
Safety
information WARNING
Seat adjustments while driving can lead
to unexpected movements of the seat. Vehicle
control could be lost. There is a risk of an accij dent. Only adjust the seat on the driver's sidewhen the vehicle is stationary.'

6Height7Backrest tilt
Forward/backward
Pull the lever and slide the seat in the desireddirection.
After releasing the lever, move the seat forj
ward or back slightly making sure it engages
properly.
Height
Pull the lever and apply your weight to the seat or lift it off, as necessary.
Backrest
tilt
Pull the lever and apply your weight to the
backrest or lift it off, as necessary.
Seat
tilt
Pull the lever and move the seat to the desired
tilt. After releasing the lever, apply your weight to the seat or lift it off to make sure the seat
engages properly.
Electrically
adjustable
seats
Overview
1Seat and mirror memory2Backrest widthSeite 54ControlsSettings54
Online Edition for Part no. 01 40 2 974 422 - X/16

3Lumbar support4Backrest tilt5Forward/backward, height, seat tilt
General
information
The seat setting for the driver's seat is stored
for the profile currently used. When the vehicle
is unlocked via the remote control, the position
is automatically retrieved if the function, refer to page 47, is activated for this purpose.
Forward/backward
Push switch forward or backward.
Height
Push switch up or down.
Seat
tilt
Move switch up or down.
Backrest
tilt
Move switch forward or backward. Thigh
support
Pull the lever at the front of the seat and adjustthe thigh support.
Lumbar
support The curvature of the seat backrest can be adj
justed in a way that it supports the lumbar rej gion of the spine. The lower back and thespine are supported for upright posture.
Seite 55SettingsControls55
Online Edition for Part no. 01 40 2 974 422 - X/16

'yPress the front/rear section
of the switch:
The curvature is increased/
decreased.'yPress the upper/lower secj
tion of the switch:
The curvature is shifted up/ down.
Backrest
width
You can change the width of the backrest usjing the side wings to adjust the lateral support.
Press button on the correj
sponding side.
Front
seat
heating
Overview
Seat heating
Switching
on Press button once for each temperajture level.
The maximum temperature is reached when three LEDs are lit.
If the trip is continued within approx. 15 mij
nutes after a stop, seat heating is activated auj
tomatically with the temperature selected last.
When ECO PRO is activated, the heater output
is reduced.
Switching
off Press and hold the button, until the
LEDs go out.
Rear
seat
heating
Overview
Seat heating
Switching
on Press button once for each temperajture level.
The maximum temperature is reached when three LEDs are lit.
If the trip is continued within approx. 15 mij
nutes after a stop, seat heating is activated auj
tomatically with the temperature selected last.
When ECO PRO is activated, the heater output
is reduced.
Switching
off Press and hold the button, until the
LEDs go out.
Seite 56ControlsSettings56
Online Edition for Part no. 01 40 2 974 422 - X/16

Safety
beltsNumber
of
safety
belts
The vehicle is fitted with five safety belts to enj
sure occupant safety. However, they can only offer protection when adjusted correctly.
The two outer safety belt buckles of the rear
seat are intended for the persons sitting on the
left and right.
The center safety belt buckle of the rear seat is
intended for the person sitting in the middle.
General
information Always make sure that safety belts are being
worn by all occupants before driving off. Alj
though airbags enhance safety by providing
added protection, they are not a substitute for safety belts.
Slowly guide the safety belt out of the holder
when fastening it.
The upper shoulder strap's anchorage point
will be correct for adult seat occupants of evj
ery build if the seat is correctly adjusted.
Safety
information WARNING
If the safety belt is used to buckle more
than one person, the protective effect of the safety belt can no longer be ensured. There is
a risk of injuries or danger to life. Do not allow more than one person to wear a single safety
belt. Infants and children are not allowed on an occupant's lap, but must be transported andsecured in designated child restraint sysj
tems.'

Buckling
the
safety
belt
Make sure you hear the latch plate engage in
the belt buckle.
Unbuckling
the
safety
belt
1.Hold the safety belt firmly.2.Press the red button in the belt buckle.3.Guide the safety belt back into its roll-up mechanism.
Safety
belt
reminder
for
driver's
and
passenger's
seat
The indicator lamp lights up and a sigj
nal sounds. Make sure that the safety
belts are positioned correctly. The
safety belt reminder is active at speeds above
approx. 6 mph/10 km/h. It can also be activated if objects are placed on the front passengerseat.
Front
head
restraints
Safety
information WARNING
A missing protective effect due to rej
moved or not correctly adjusted head rej
straints can cause injuries in the head and neck area. There is a risk of injury. Before drivj
ing, install the head restraints on the occupied seats. Ensure that the middle of the head rej
straint supports the back of the head approxij
mately at eye level.'

Adjusting
the
height'yTo raise: push the head restraint up.'yTo lower: press button, arrow 1, and push
head restraint down.
Tilt
Three different tilt positions are available.
'yForward: pull the top edge of the head rej
straint forward, arrow 1.'yBack: press the button, arrow 2. The head restraint folds as far back as possible.
Removing
Only remove the head restraint if no one will besitting in the seat in question.
1.Raise the head restraint up against the rej
sistance.2.Press button, arrow 1, and pull the head rej
straint out completely.
Rear
head
restraints
Safety
information WARNING
A missing protective effect due to rej
moved or not correctly adjusted head rej
straints can cause injuries in the head and neck area. There is a risk of injury. Before drivj
ing, install the head restraints on the occupied seats. Ensure that the middle of the head rej
straint supports the back of the head approxij
mately at eye level.'

'yDo not use any accessories, e.g., pillows,
while driving.'