BMW 4 SERIES COUPE 2018 Owners Manual

The symbol on the automatic climate conj
trol flashes when the system has been switched on.
The system will only be switched on within the
next 24 hours. After that, it needs to be reactij vated.Seite 181Climate
controlControls181
Online Edition for Part no. 01402978272 - II/17

Interior
equipmentVehicle
features
and
optionsThis chapter describes all standard, country-specific and optional features offered with theseries. It also describes features that are notnecessarily available in your vehicle, e. g., due
to the selected options or country versions.
This also applies to safety-related functions
and systems. When using these functions and systems, the applicable laws and regulations
must be observed.
Universal
Integrated
Remote
Control
Concept
The integrated Universal Remote Control in
the interior mirror can operate up to 3 funcj
tions of remote-controlled systems, such as
garage door drives or lighting systems. The integrated Universal Remote Control replaces
up to 3 different hand-held transmitters. To
operate the remote control, the buttons on the
interior mirror must be programmed with the
desired functions. The hand-held transmitter
for the particular system is required in order to
program the remote control.
Before selling the vehicle, delete the stored
functions for the sake of security.
Safety
information WARNING
Body parts can be jammed when operatj
ing remote-controlled systems, e.g., the gaj
rage door, using the integrated universal rej mote control. There is a risk of injury or risk ofproperty damage. Make sure that the area ofmovement of the respective system is clear
during programming and operation. Also followthe safety instructions of the hand-held transj
mitter.'

proximately 20 seconds until the LED on
the interior mirror flashes. This erases all
programming of the buttons on the interior mirror.3.Hold the hand-held transmitter for the sysjtem to be controlled approx. 1 to 3 inj
ches/2.5 to 8 cm away from the buttons of
the interior mirror. The required distance
depends on the hand-held transmitter.4.Simultaneously press and hold the button
of the desired function on the hand-held transmitter and the button to be programj
med on the interior mirror. The LED on the
interior mirror will begin flashing slowly.5.Release both buttons as soon as the LED flashes more rapidly. The LED flashing
faster indicates that the button on the intej
rior mirror has been programmed.
If the LED does not flash faster after at
least 60 seconds, change the distance bej
tween the interior mirror and the hand-held transmitter and repeat the step. Several
more attempts at different distances may be necessary. Wait at least 15 seconds bej
tween attempts.
Canada: if programming with the hand- held transmitter was interrupted, hold
down the interior mirror button and repeatj
edly press and release the hand-held
transmitter button for 2 seconds.6.To program other functions on other butj
tons, repeat steps 3 to 5.
The systems can be controlled using the intej
rior mirror buttons.
Special
feature
of
the
rolling
code
wireless
system
If you are unable to operate the system after
repeated programming, please check if the system to be controlled features a rolling coderadio system.
Read the system's owner's manual, or press the programmed button on the interior mirror longer. If the LED on the interior mirror starts
flashing rapidly and then stays lit constantly for
2 seconds, the system features a rolling code
radio system. Flashing and continuous illumij
nation of the LED will repeat for approximately
20 seconds.
For systems with a rolling code radio system,
the integrated Universal Remote Control and the system also have to be synchronized.
Please read the owner's manual to find out
how to synchronize the system.
Synchronizing is easier with the aid of a secj
ond person.
Synchronizing the universal remote control with the system:1.Park the vehicle within range of the rejmote-controlled system.2.Program the desired button on the interiormirror as described.3.Locate and press the synchronizing button
on the system being programmed. You
have approx. 30 seconds for the next step.4.Hold down the programmed button on the
interior mirror for approximately 3 seconds
and then release it. If necessary, repeat this step up to three times in order to finish
synchronization. Once synchronization is
complete, the programmed function will be carried out.
Reprogramming
individual
buttons
1.Switch on the ignition.2.Press and hold the interior mirror button tobe programmed.3.As soon as the interior mirror LED starts
flashing slowly, hold the hand-held transj
mitter for the system to be controlled apj prox. 1 to 3 inches/2.5 to 8 cm away from
the buttons of the interior mirror. The rej
quired distance depends on the hand-held transmitter.Seite 183Interior
equipmentControls183
Online Edition for Part no. 01402978272 - II/17

4.Likewise, press and hold the button of the
desired function on the hand-held transj mitter.5.Release both buttons as soon as the intej
rior mirror LED flashes more rapidly. The LED flashing faster indicates that the butj
ton on the interior mirror has been proj
grammed. The system can then be conj
trolled by the button on the interior mirror.
If the LED does not flash faster after at
most 60 seconds, change the distance and
repeat the programming starting with
step 4. Several more attempts at different
distances may be necessary. Wait at least 15 seconds between attempts.
Canada: if programming with the hand-
held transmitter was interrupted, hold
down the interior mirror button and repeatj
edly press and release the hand-held
transmitter button for 2 seconds.
Operation
WARNING
Body parts can be jammed when operatj
ing remote-controlled systems, e.g., the gaj
rage door, using the integrated universal rej
mote control. There is a risk of injury or risk of
property damage. Make sure that the area of movement of the respective system is clear
during programming and operation. Also follow
the safety instructions of the hand-held transj
mitter.'

World
map
with
magnetic
zonesProcedure1.Press and hold the control button for apjprox. 3 to 4 seconds. The number of theset compass zone appears in the mirror.2.To change the zone setting, press the conj
trol button quickly and repeatedly until the
number of the compass zone that correj sponds with your location appears in the
mirror.
The set zone is stored automatically. The comj
pass is ready for use again after approximately
10 seconds.
Calibrating
the
digital
compass
The digital compass must be calibrated in the
event of the following:
'yThe wrong compass point is displayed.'yThe point of the compass displayed does not change despite changing the directionof travel.'yNot all points of the compass are disj
played.Procedure1.Make sure that there are no large metallic
objects or overhead power lines near the
vehicle and that there is sufficient room to
drive around in a circle.2.Set the currently applicable compass zone.3.Press and hold the control button for apj prox. 6 to 7 seconds so that "C" appears
on the display. Next, drive in a complete circle at least once at a speed of no more
than 4 mph/7 km/h. If calibration is sucj
cessful, the "C" is replaced by the points of
the compass.
Left/right-hand
steering
The digital compass is already set for right or
left-hand steering at the factory.
Setting
the
language
Press and hold the control button for approx.
12 to 13 seconds. Briefly press the control
button again to switch between English "E" and German "O".
Seite 185Interior
equipmentControls185
Online Edition for Part no. 01402978272 - II/17

Settings are stored automatically after approxijmately 10 seconds.
Sun
visor
Glare
shield Fold the sun visor down or up.
Vanity
mirror A vanity mirror is located in the sun visor bejhind a cover. When the cover is opened, themirror lighting switches on.
Ashtray/cigarette
lighterAshtray
Opening
Slide the cover forward.
Installing
The ashtray can be inserted in both cup holdj ers.
Emptying
Take out the insert.
Cigarette
lighter WARNING
Contact with hot heating elements or the
hot socket of the cigarette lighter can cause
burns. Flammable materials can ignite if the
cigarette lighter falls down or is held against
the respective objects. There is a risk of fire
and injuries. Hold the cigarette lighter by its
handle. Make sure that children do not use the
cigarette lighter and burn themselves.'

Push in the cigarette lighter.
The cigarette lighter can be rej
moved as soon as it pops back
out.
Sockets General
information
The lighter socket can be used as a socket for electrical equipment while the engine is runjning or when the ignition is switched on.
The total load of all sockets must not exceed 140 watts at 12 volts.
Do not damage the socket by using non-comj patible connectors.
Safety
information WARNING
Devices and cables in the unfolding area
of the airbags, for instance portable navigation
devices, can hinder the unfolding of the airbag
or be thrown around in the car's interior when
unfolding. There is a risk of injury. Make sure
that devices and cables are not in the airbag's
area of unfolding.'

In
the
cargo
area
The socket is located on the left side in the
cargo area.
USB
interface
Concept
Mobile devices with USB port can be conj
nected to the USB interface.
General
information
Observe the information regarding the conj nection of mobile devices to the USB interfacein section USB connections, refer to page 35.
In
the
center
armrest
A USB interface is located in the center armj rest.
In
the
center
console
A USB interface is located in the center conjsole.
Cargo
area Cargo
cover
Safety
information WARNING
Loose objects or devices with a cable
connection to the vehicle, e.g., mobile phones, can be thrown into the vehicle's interior while
driving, e.g., in the event of an accident or durj ing braking and evasive maneuvers. There is arisk of injury. Secure loose objects or devices
with a cable connection to the vehicle in the vehicle's interior.'

RemovingCargo
cover
in
rear
window1.Pull the cargo cover with both hands by the
outer edges towards the rear, arrows 1, to
disengage it from the catches.2.Pull the cargo cover downwards, arrow 2,
and remove it.
Cargo
cover
in
the
cargo
area
Push the cargo cover upwards, arrow 1, until it
disengages from the catches and then pull it towards the front, arrow 2.
Installing Proceed in the reverse order to reinstall. The
cargo covers must snap audibly into place on their respective holders.
Enlarging
the
cargo
area
Concept
The cargo area can be enlarged by folding
down the rear seat backrest.
General
information
The rear seat backrest is divided at a ratio of
60 to 40. The left rear seat backrest is conj nected to the center section.
With the through-loading system: the rear seat backrest is divided into three parts at a ratio of
40/20/40. The side rear seat backrests and the
center section can be folded down separately.
Safety
information WARNING
Danger of jamming with folding down the
backrests. There is a risk of injury or risk of property damage. Make sure that the area ofmovement of the rear backrest and the of thehead restraint is clear prior to folding down.'

NOTE
Vehicle parts can be damaged when
folding down the rear backrest. There is a risk of property damage. Make sure that the area of
movement of the rear backrest including head
restraint is clear when folding down.'