BMW X5M 2017 Owners Manual

Engine
oilVehicle
features
and
options
This chapter describes all standard, country- specific and optional features offered with theseries. It also describes features that are notnecessarily available in your vehicle, e. g., due
to the selected options or country versions.
This also applies to safety-related functions
and systems. When using these functions and systems, the applicable laws and regulations
must be observed.
General
information
The engine oil consumption is dependent on
the driving style and driving conditions.
The engine oil consumption can increase in
the following situations, for example:'ySporty driving style.'yBreak-in of the engine.'yIdling of the engine.'yWith use of engine oil types that are classij
fied as not suitable.
Therefore, regularly check the engine oil level
after refueling.
When a dynamic driving style is used, such as when cornering fast, the system is unable tomeasure the engine oil level. With this driving
style, measure the engine oil level using a dej tailed measurement, refer to page 222.
The vehicle is equipped with electronic oil
measurement.
The electronic oil measurement has two measj uring principles:
'yStatus display.'yDetailed measurement.Electronic
oil
measurement
Status
display
Concept
The engine oil level is monitored electronically
while driving and shown on the Control Disj play.
If the engine oil level reaches the minimum
level, a Check Control message is displayed.
Functional
requirements A current measured value is available after apj
prox. 30 minutes of driving. During a shorter
trip, the status of the last, sufficiently long trip
is displayed.
With frequent short-distance trips, regularly perform a detailed measurement.
Displaying
the
engine
oil
level
Using iDrive:1."Vehicle info"2."Vehicle status"3. "Engine oil level"
The engine oil level is displayed.
Engine
oil
level
display
messages
Concept
Different messages appear on the display dej pending on the engine oil level. Pay attention
to these messages.
If the engine oil level is too low within the next
125 miles/200 km, add engine oil.
Take care not to add too much engine oil.
A red indicator light indicates that theengine oil pressure is too low.
Seite 221Engine
oilMobility221
Online Edition for Part no. 01402978527 - II/17

Safety
informationNOTE
An engine oil level that is too low causes
engine damage. There is a risk of property
damage. Immediately add engine oil.'

Opening
the
oil
filler
neck1.Opening the hood, refer to page 2192.Open the lid counterclockwise.3.Add engine oil.
Engine
oil
types
to
add
General
information
The engine oil quality is critical for the life of
the engine.
Safety
information NOTE
Oil additives can damage the engine.
There is a risk of property damage. Do not use oil additives.'

Seite 224MobilityEngine
oil224
Online Edition for Part no. 01402978527 - II/17

CoolantVehicle
features
and
optionsThis chapter describes all standard, country-specific and optional features offered with theseries. It also describes features that are notnecessarily available in your vehicle, e. g., due
to the selected options or country versions.
This also applies to safety-related functions
and systems. When using these functions and systems, the applicable laws and regulations
must be observed.
General
information
The vehicle has two coolant reservoirs that are
located in the engine compartment.
To ensure the operational reliability of the vehij
cle, always check the coolant level of both
coolant reservoirs.
Not all commercially available additives are suitable for the vehicle. Information about suitjable additives is available from a dealerss servjice center or another qualified service center or
repair shop.
Safety
information WARNING
With the engine hot and the cooling sysj
tem open, coolant can escape and lead to
scalding. There is a risk of injury. Only open the cooling system with the engine cooleddown.'

Adding1.Let the engine cool.2.Turn the lid of the coolant reservoir slightlycounterclockwise to allow any excess
pressure to dissipate, then open it.3.If the coolant is low, slowly add coolant up to the specified level; do not overfill.4.Close the cap.5.Have the cause of the coolant loss elimijnated as soon as possible.
Disposal
Comply with the relevant environmenj
tal protection regulations when disposj
ing of coolant and coolant additives.
Seite 226MobilityCoolant226
Online Edition for Part no. 01402978527 - II/17

MaintenanceVehicle
features
and
options
This chapter describes all standard, country- specific and optional features offered with theseries. It also describes features that are notnecessarily available in your vehicle, e. g., due
to the selected options or country versions.
This also applies to safety-related functions
and systems. When using these functions and systems, the applicable laws and regulations
must be observed.
BMW
maintenance
system The maintenance system indicates requiredmaintenance measures, and thereby provides
support in maintaining road safety and the opj erational reliability of the vehicle.
In some cases, scopes and intervals may vary
according to the country-specific version. Rej
placement work, spare parts, fuels and lubrij
cants, and wear materials are calculated sepaj rately. Further information is available from a
dealerss service center or another qualified service center or repair shop.
Condition
Based
Service
CBS
Concept
Sensors and special algorithms take into acj
count the driving conditions of the vehicle.
CBS uses these to calculate the need for
maintenance.
The system makes it possible to adapt the amount of maintenance corresponding to your user profile.General
information
Information on service requirements, refer to page 97, can be displayed on the Control Disj
play.
Service
data
in
the
remote
control Information on the required maintenance iscontinuously stored in the remote control. Thedealerss service center can read this data outand suggest a maintenance scope for the vehijcle.
Therefore, hand the service advisor the remote
control with which the vehicle was driven most
recently.
Storage
periods Storage periods during which the vehicle batj
tery was disconnected are not taken into acj count.
If this occurs, have a dealer's service center or another qualified service center or repair shop update the time-dependent maintenance projcedures, such as checking brake fluid and, if
necessary, changing the engine oil and the mij
crofilter/activated-charcoal filter.
Service
and
Warranty
Information
Booklet
for
US
models
and
Warranty
and
Service
Guide
Booklet
for
Canadian
models
Please consult your Service and Warranty Inj
formation Booklet for US models and Warranty
and Service Guide Booklet for Canadian modj els for additional information on service rejquirements.
The manufacturer of your vehicle recommends that maintenance and repair be performed by a
dealerss service center or another qualifiedSeite 227MaintenanceMobility227
Online Edition for Part no. 01402978527 - II/17

service center or repair shop. Records of reguj
lar maintenance and repair work should be rej
tained.
Socket
for
OBD
Onboard
Diagnosis
Safety
information NOTE
The socket for Onboard Diagnosis is an
intricate component intended to be used in
conjunction with specialized equipment to check the vehicless primary emissions system.Improper use of the socket for Onboard Diagjnosis, or contact with the socket for Onboard
Diagnosis for other than its intended purpose,
can cause vehicle malfunctions and creates risks of personal and property damage. Given
the foregoing, the manufacture of your vehicle
strongly recommends that access to the socket for Onboard Diagnosis be limited to a
dealer's service center or another qualified service center or repair shop or other persons
that have the specialized training and equipj
ment for purposes of properly utilizing the
socket for Onboard Diagnosis.'

Replacing
componentsVehicle
features
and
optionsThis chapter describes all standard, country-specific and optional features offered with theseries. It also describes features that are notnecessarily available in your vehicle, e. g., due
to the selected options or country versions.
This also applies to safety-related functions
and systems. When using these functions and systems, the applicable laws and regulations
must be observed.
Onboard
vehicle
tool
kit1.Fold up the cargo floor panel.2.Remove the onboard vehicle tool kit.Wiper
blade
replacementSafety
information NOTE
If the wiper arm falls onto the windshield
without the wiper blades installed, the windj shield can be damaged. There is a risk of propjerty damage. Secure the wiper arm when rejplacing the wiper blades and do not fold downthe wipers without the wiper blades installed.'

3.Fold open the holder.4.Slide wiper blade out of the wiper arm.5.Insert the new wiper blade and press it on
until it you hear it snap into the holder.6.Fold down the wipers.
BMW
X5
M:
rear
1.Fold up the wiper arm.2.Turn the wiper blade all the way back.3.Continue turning the wiper blade all the way so that it pops out of the holder.4.Press the new wiper blade into the holderuntil you hear it snap into place.5.Fold the wipers in.Light/bulb
replacement
General
information
Lights
and
bulbs
Lights and bulbs make an essential contribuj
tion to vehicle safety.
The vehicle manufacturer recommends that
you have the relevant work carried out a dealj erss service center or another qualified servicecenter or repair shop.
A spare light box is available from a dealerss
service center or another qualified service cenj
ter or repair shop.
Observe the safety information, refer to
page 230.
Light-emitting
diodes
(LEDs)
Some items of equipment use light-emitting
diodes installed behind a cover as a light source. These light-emitting diodes, which arerelated to conventional lasers, are officially
designated as Class 1 light-emitting diodes.
Observe the safety information, refer topage 230.
Safety
information
Lights
and
bulbs WARNING
Bulbs can get hot during operation. Conj
tact with the bulbs can cause burns. There is a
risk of injury. Only change bulbs after they
have cooled off.'