warning BUICK LUCERNE 2007 Owner's Guide

Anti-Lock Brake System
Warning Light
With the anti-lock brake
system, the light(s) will
come on when your
engine is started and
may stay on for
several seconds.
That’s normal.
If the light stays on, turn the ignition to OFF. Or, if
the light comes on when you’re driving, stop as
soon as possible and turn the ignition off. Then start
the engine again to reset the system. If the light still
stays on, or comes on again while you’re driving,
your vehicle needs service. If the regular brake
system warning light isn’t on, you still have brakes,
but you don’t have anti-lock brakes. If the regular
brake system warning light is also on, you don’t
have anti-lock brakes and there’s a problem with
your regular brakes. SeeBrake System Warning
Light on page 201.
The anti-lock brake system warning light will come
on briey when you turn the ignition key to RUN.This is normal. If the light doesn’t come on then,
have it xed so it will be ready to warn you if there
is a problem.Traction Control System (TCS)
Warning Light
This warning light
should come on briey
when the engine is
started.
If the warning light does not come on then, have it
xed so it will be ready to warn you if there is a
problem. If it stays on, or comes on when you are
driving a SERVICE TRACTION CONTROL
message will appear in the Driver Information
Center (DIC). This indicates that there may be a
problem with your traction control system and your
vehicle may need service. When this warning light
is on and the SERVICE TRACTION CONTROL
message appears on the DIC, the system will not
limit wheel spin. Adjust your driving accordingly.
202

If the traction control system is manually turned
off, this light will come on and the TRACTION
CONTROL OFF message will appear on the DIC.
When the system is active, the light will ash
while the system is limiting wheel spin or assisting
you in controlling the vehicle. You may also feel
or hear the system working. This is normal.
SeeTraction Control System (TCS) on page 283
andDIC Warnings and Messages on page 221
for more information.
StabiliTrak®Indicator Light
This warning light
should come on
briey when the
engine is started.If the warning light does not come on then, have it
xed so it will be ready to warn you if there is a
problem. This light may come on after you rst start
to drive and the STABILITRAK NOT READY
message will appear in the Driver Information
Center (DIC). SeeStabiliTrak
®System on
page 284for more information.
If the light stays on, or comes on when you are
driving a SERVICE STABILITRAK message
will appear in the DIC. This indicates that there
may be a problem with the StabiliTrak
®system
and your vehicle may need service. When
this warning light is on and the SERVICE
STABILITRAK message appears on the DIC,
the system will not assist you in controlling
the vehicle. Adjust your driving accordingly.
When the system is active, the light will ash
while the system is assisting you in controlling the
vehicle. You may also feel or hear the system
working. This is normal.
SeeStabiliTrak
®System on page 284andDIC
Warnings and Messages on page 221for
more information.
203

Engine Coolant Temperature
Warning Light
The engine coolant
temperature warning
light will come on
when the engine
has overheated.
If this happens you should pull over and turn off
the engine as soon as possible. SeeEngine
Overheating on page 351for more information.
Notice:Driving with the engine coolant
temperature warning light on could cause your
vehicle to overheat. SeeEngine Overheating
on page 351. Your vehicle could be damaged,
and it might not be covered by your warranty.
Never drive with the engine coolant
temperature warning light on.
This light will also come on briey when starting
your vehicle. If it does not, have your vehicle
serviced.
Engine Coolant Temperature Gage
This gage shows the engine coolant temperature. If
the pointer moves towards the H (United States) or
shaded in thermostat symbol area (Canada), the
engine is too hot.
A temperature indicator light will turn on and a
chime will sound.
If you have been operating your vehicle under
normal driving conditions, and the temperature
indicator light comes on, you should pull off
the road, stop your vehicle and turn off the
engine as soon as possible.
United StatesCanada
204

Tire Pressure Light
This light comes on
briey when you turn
the ignition to RUN.
It will also come on when one or more of your
tires are signicantly underinated.If your vehicle has a Driver Information Center
(DIC), a CHECK TIRE PRESSURE message will
accompany the light. SeeDIC Warnings and
Messages on page 221for more information.
Stop and check your tires as soon as it is safe to do
so. If underinated, inate to the proper pressure.
SeeTires on page 385for more information.
This light will ash for about 60 seconds and then
stay on if a problem is detected with the Tire
Pressure Monitor system.
SeeTire Pressure Monitor System on page 393
for more information.
205

Fuel Gage
The fuel gage shows about how much fuel is in your
tank. It works only when the ignition is on. When the
indicator moves to the edge of the low fuel warning
band, the low fuel warning light will come on and a
chime will sound. You still have a little fuel left, but
you need to get more fuel right away.Here are some things that some owners ask
about. None of these show a problem with your
fuel gage:
At the service station, the gas pump shuts off
before the gage reads full.
It takes more (or less) fuel to ll up than the
gage indicated. For example, the gage may
have indicated half full, but it took more
(or less) than half the tank’s capacity to ll it.
The gage moves up a little when you turn a
corner, speed up or make a hard stop.
The gage does not go back to empty when
you turn off the ignition.United StatesCanada
211

Driver Information Center (DIC)
Your vehicle has a Driver Information Center (DIC).
All messages will appear in the DIC display
located below the speedometer in the instrument
panel cluster. The DIC buttons are located on
the instrument panel, to the left of the instrument
panel cluster.
The DIC comes on when the ignition is on. After a
short delay, the DIC will display the information
that was last displayed before the engine was
turned off.
The DIC displays trip, fuel, and vehicle system
information, and warning messages if a system
problem is detected. The bottom line of the
DIC shows the shift lever position indicator.
SeeAutomatic Transaxle Operation on page 119
for more information.If your vehicle’s DIC has these features, the
compass direction and the outside air temperature
may also display on the DIC when viewing the
trip and fuel information. The compass direction
appears on the top right corner of the DIC display.
The outside air temperature automatically
appears in the bottom right corner of the DIC
display. If there is a problem with the system that
controls the temperature display, the numbers
will be replaced with dashes. If this occurs, have
the vehicle serviced by your dealer.
The DIC also allows some features to be
customized. SeeDIC Vehicle Customization on
page 231for more information.
DIC Controls and Displays
The DIC has different displays which can be
accessed by pressing the DIC buttons located on
the instrument panel, to the left of the instrument
panel cluster.
212

Each trip odometer can be reset to zero separately
by pressing the set/reset button while the desired
trip odometer is displayed.
The trip odometer has a feature called the
retro-active reset. This can be used to set the trip
odometer to the number of miles (kilometers) driven
since the ignition was last turned on. This can be
used if the trip odometer is not reset at the
beginning of the trip.
To use the retro-active reset feature, press and hold
the set/reset button for at least four seconds. The
trip odometer will display the number of miles (mi)
or kilometers (km) driven since the ignition was last
turned on and the vehicle was moving. Once the
vehicle begins moving, the trip odometer will
accumulate mileage. For example, if the vehicle
was driven 5 miles (8 km) before it is started again,
and then the retro-active reset feature is activated,
the display will show 5 miles (8 km). As the vehicle
begins moving, the display will then increase to
5.1 miles (8.2 km), 5.2 miles (8.4 km), etc.
If the retro-active reset feature is activated after the
vehicle is started, but before it begins moving, the
display will show the number of miles (mi) or
kilometers (km) that were driven during the last
ignition cycle.Fuel Range
Press the trip/fuel button until FUEL RANGE
displays. This display shows the approximate
number of remaining miles (mi) or kilometers (km)
the vehicle can be driven without refueling.
The fuel range estimate is based on an average of
the vehicle’s fuel economy over recent driving
history and the amount of fuel remaining in the fuel
tank. This estimate will change if driving conditions
change. For example, if driving in traffic and making
frequent stops, this display may read one number,
but if the vehicle is driven on a freeway, the number
may change even though the same amount of fuel
is in the fuel tank. This is because different driving
conditions produce different fuel economies.
Generally, freeway driving produces better fuel
economy than city driving.
If your vehicle is low on fuel, the FUEL LEVEL
LOW message will be displayed. See “FUEL
LEVEL LOW” underDIC Warnings and Messages
on page 221for more information.
214

Vehicle Information Menu Items
T
(Vehicle Information):Press this button to
scroll through the following menu items:
Oil Life
Press the vehicle information button until OIL LIFE
REMAINING displays. This display shows an
estimate of the oil’s remaining useful life. If you
see 99% OIL LIFE REMAINING on the display,
that means 99% of the current oil life remains.
The engine oil life system will alert you to change
the oil on a schedule consistent with your driving
conditions.
When the remaining oil life is low, the CHANGE
ENGINE OIL SOON message will appear on the
display. See “CHANGE ENGINE OIL SOON” under
DIC Warnings and Messages on page 221. You
should change the oil as soon as possible. See
Engine Oil on page 337. In addition to the engine
oil life system monitoring the oil life, additional
maintenance is recommended in the Maintenance
Schedule in this manual. SeeScheduled
Maintenance on page 442for more information.Remember, you must reset the OIL LIFE yourself
after each oil change. It will not reset itself. Also, be
careful not to reset the OIL LIFE accidentally at any
time other than when the oil has just been changed.
It cannot be reset accurately until the next oil
change. To reset the engine oil life system,
seeEngine Oil Life System on page 340.
Park Assist
If your vehicle has the Ultrasonic Rear Parking
Assist (URPA) system, this display allows the
system to be turned on or off. Once in this display,
press the set/reset button to select between ON or
OFF. If you choose ON, the system will be turned
on. If you choose OFF, the system will be turned
off. The URPA system automatically turns back
on after each vehicle start. When the URPA system
is turned off and the vehicle is shifted out of
PARK (P), the DIC will display the PARK ASSIST
OFF message as a reminder that the system has
been turned off. SeeDIC Warnings and Messages
on page 221andUltrasonic Rear Parking Assist
(URPA) on page 178for more information.
216

Units
Press the vehicle information button until UNITS
displays. This display allows you to select between
English or Metric units of measurement. Once in
this display, press the set/reset button to select
between ENGLISH or METRIC units.
Tire Pressure
The pressure for each tire can be viewed in the
DIC. The tire pressure will be shown in either
pounds per square inch (psi) or kilopascals (kPa).
Press the vehicle information button until the
DIC displays FRONT TIRES PSI (kPa) LEFT ##
RIGHT ##. Press the vehicle information button
again until the DIC displays REAR TIRES
PSI (kPa) LEFT ## RIGHT ##.
If a low or high tire pressure condition is detected by
the system while driving, a message advising you
to check the pressure in a specic tire will appear
in the display. SeeInation - Tire Pressure on
page 392andDIC Warnings and Messages on
page 221for more information.
If the tire pressure display shows dashes instead of
a value, there may be a problem with your vehicle.
If this consistently occurs, see your dealer for
service.
Learn Tire Positions
To access this display, the vehicle must be in
PARK (P). After rotating the tires or after replacing
a tire or sensor, the Tire Pressure Monitor (TPM)
system must re-learn the tire positions. To re-learn
the tire positions, seeTire Pressure Monitor System
on page 393. SeeTire Inspection and Rotation on
page 398andDIC Warnings and Messages on
page 221for more information.
Compass Zone
Your vehicle may have this feature. Under
certain circumstances, such as during a long
distance cross-country trip, it will be necessary to
compensate for compass variance and reset the
zone. To change the compass zone through the
DIC, seeDIC Compass on page 218.
Compass Calibration
The compass can be manually calibrated. To
calibrate the compass through the DIC, seeDIC
Compass on page 218.
217

DIC Warnings and Messages
Messages are displayed on the DIC to notify the
driver that the status of the vehicle has changed
and that some action may be needed by the driver
to correct the condition. Multiple messages may
appear one after another. Some messages may not
require immediate action, but you can press the
set/reset button to acknowledge that you received
the message and clear it from the DIC display.
Pressing any of the DIC buttons also acknowledges
and clears any messages. Some messages cannot
be cleared from the DIC display because they are
more urgent. These messages require action
before they can be cleared. You should take any
messages that appear on the display seriously and
remember that clearing the messages will only
make the messages disappear, not correct the
problem. The following are the possible messages
that can be displayed and some information
about them.
AUTOMATIC LIGHT CONTROL OFF
This message displays when the automatic
headlamps are turned off. SeeExterior Lamps
on page 170for more information.
AUTOMATIC LIGHT CONTROL ON
This message displays when the automatic
headlamps are turned on. SeeExterior Lamps
on page 170for more information.
BATTERY SAVER ACTIVE
This message displays when the system detects
that the battery voltage is dropping beyond a
reasonable level. The battery saver system starts
reducing certain features of the vehicle that you
may be able to notice. At the point that the features
are disabled, this message is displayed. It means
that the vehicle is trying to save the charge in the
battery.
Turn off all unnecessary accessories to allow the
battery to recharge.
The normal battery voltage range is
11.5 to 15.5 volts.
221