keyless entry BUICK RANDEZVOUS 2002 Owner's Guide

2-106
When the ignition is turned to ON or START, the DIC
will display the following:
BUICK: BUICK will be displayed for three seconds.
DRIVER #: This message will be displayed for another
three seconds after BUICK appears in the display. This
display lets the driver know which driver's remote
keyless entry transmitter is being used and the driver's
customization features.
The DIC controls are
located to the left of the
steering column on the
instrument panel.
The DIC will be in the last mode displayed when the
engine was turned off. To select a different mode, press
MODE. The display will cycle through its options at
each press of MODE.MODE: This button lets you cycle through the options
on the display.
SET: This button is used to select and set the options to
your preference.
Driver Information Center (DIC) Messages
The DIC will always display the compass reading and
the outside temperature. If the temperature is below
38
F (3
C), the temperature reading will toggle
between displaying the temperature and the word ICE
for two minutes.
AVG ECONOMY: Average fuel economy is viewed as
a long term approximation of your overall driving
conditions. To learn the average fuel economy from a
new starting point, press and hold the SET button while
the average fuel economy is displayed on the DIC. The
average fuel economy will set to zero.
INST ECONOMY: Instantaneous fuel economy varies
with your driving conditions, such as acceleration,
braking and the grade of the road being traveled.

2-109
ZONE # PRESS & HOLD SET TO CHANGE: This
display mode will be displayed when you are manually
calibrating the system. The current zone number for
compass variance will be displayed in place of the
# symbol. Use the SET button to select the zone number
from the graphic shown to select the current area of the
country that you are driving in.
PRESS SET TO CALIBRATE COMPASS: After
selecting your zone, press the MODE button and this
will be displayed on the DIC. Press the SET button and
complete three 360 degree turns in an area free from
large metal objects.
The following two messages will toggle in the display
until you calibrate the compass:

DRIVE VEHICLE IN CIRCLE

CALIBRATING COMPASS
When calibration is complete, the display will return to
its normal mode.Driver Information Center (DIC)
Vehicle Customization
The DIC is used to program the choices of two drivers.
The drivers are recognized as DRIVER 1 and
DRIVER 2 in the DIC display. You will let the DIC
know which driver you are by using your remote keyless
entry transmitter. Each remote keyless entry transmitter
was pre
-programmed to belong to DRIVER 1 or
DRIVER 2. Each transmitter may be programmed
differently for each driver's preferences.
After you press the LOCK button on your transmitter
and the ignition key is in ON, the DIC will display the
identified driver number. The vehicle will also recall the
vehicle customization features that were last
programmed to correspond to your transmitter.
If you unlock your vehicle using your key instead of
your transmitter, the DIC will not change drivers and
your vehicle will recall the information from the last
transmitter used.

2-110
Entering Programming Mode
To program features, your vehicle must be in the
programming mode. Follow these steps:
1. Turn the ignition key to ON with the vehicle
in PARK (P).
2. Press and release the MODE button,
scrolling through the DIC messages, until
PERSONALIZATION PRESS SET TO
BEGIN is displayed.
3. Press the SET button and TO SELECT DRIVER
PRESS REMOTE LOCK will appear. Press the
LOCK button on the optional remote keyless entry to
start. This identifies which remote keyless entry
transmitter is being programmed by displaying
PERSONALIZATION FOR DRIVER 1 or
PERSONALIZATION FOR DRIVER 2.
United States Canada
4. The program mode message will appear in the
message center as an indication that your vehicle is
ready to begin programming.
5. Follow the instructions given by the DIC.

2-112
Interior Lighting Delay
The interior lighting delay feature can be programmed
to one of the following modes:
ON: Continue to illuminate the interior lamps for
25 seconds after all doors have been closed so that
you can find your ignition and buckle your safety belt
at night.
Interior lighting delay will not occur while the ignition
is in ON. After 25 seconds have passed, the interior
lamps will slowly fade out. The lamps will fade out
before the 25 seconds have passed if the following
conditions are met:

The ignition is turned to ON,

all doors are locked using the optional remote
keyless entry transmitter, or

there is no occupant activity detected for an
illumination period of 25 seconds.
OFF: The interior will not illuminate your vehicle when
all of the doors are closed.Before your vehicle was shipped from the factory, it was
programmed in ON. The mode to which the vehicle has
been programmed may have been changed since it left
the factory. To determine the mode to which your
vehicle is programmed or to program your vehicle to a
different mode, do the following:
1. Follow the instructions for ªEntering Programming
Modeº listed previously.
2. Press the MODE button until INTERIOR
LIGHTING DELAY appears on the DIC.
3. Press the SET button until the arrow is before ON
or OFF.
The mode you selected is now set. You can either exit
programming mode by following the instructions later in
this section or program the next feature available on
your vehicle.

2-113
Interior Lighting On
The interior lighting on feature can be programmed to
one of the following modes:
KEY OUT: The interior lamps will come on for
about 25 seconds whenever you remove the key from
the ignition.
DOOR: The interior lamps will come on for about
25 seconds when any door is opened.
Interior lighting on will not occur while the ignition is in
ON. After 25 seconds have passed, the interior lamps
will slowly fade out. The lamps will fade out before the
25 seconds have passed if the following conditions
are met:

The ignition is turned to ON,

LOCK is pressed on the optional remote keyless
entry transmitter, or

there is no occupant activity detected for an
illumination period of 25 seconds.Before your vehicle was shipped from the factory, it was
programmed in DOOR. The mode to which the vehicle
has been programmed may have been changed since it
left the factory. To determine the mode to which your
vehicle is programmed or to program your vehicle to a
different mode, do the following:
1. Follow the instructions for ªEntering Programming
Modeº listed previously.
2. Press the MODE button until INTERIOR
LIGHTING ON appears on the DIC.
3. Press the SET button until the arrow is before KEY
OUT or DOOR.
The mode you selected is now set. You can either exit
programming mode by following the instructions later in
this section or program the next feature available on
your vehicle.

2-116
Delayed Locking
The delayed locking feature can be programmed to one
of the following modes:
ON: Lock your vehicle using the power door lock
switch or the optional remote keyless entry transmitter
while any door is opened, you will hear three chimes
and the doors will not lock. Five seconds after the last
door is closed, all doors will lock.
Once delayed locking is programmed to ON, you can do
the following:

Cancel the delayed locking by pressing unlock using
the power door lock switch or by fully inserting the
key in the ignition,

override the delayed locking feature by pressing lock
immediately using the power door lock switch, or

let the delayed locking feature complete the locking
of the vehicle.OFF: The doors will always lock immediately when
you lock the doors using the power door lock switch
or press LOCK on the optional remote keyless
entry transmitter.
Before your vehicle was shipped from the factory, it was
programmed in ON. The mode to which the vehicle has
been programmed may have been changed since it left
the factory. To determine the mode to which your
vehicle is programmed or to program your vehicle to a
different mode, do the following:
1. Follow the instructions for ªEntering Programming
Modeº listed previously.
2. Press the MODE button until DELAYED LOCKING
appears on the DIC.
3. Press the SET button until the arrow is before ON
or OFF.
The mode you selected is now set. You can either exit
programming mode by following the instructions later in
this section or program the next feature available on
your vehicle.

2-117
Remote Door Unlock
The remote door unlock feature can be programmed to
one of the following modes:
DRIVER/ALL: With the first press of UNLOCK on
the remote keyless entry transmitter, the driver's door
will unlock, and with the second press of UNLOCK,
within five seconds of the first press, all passenger's
doors will unlock.
ALL: All doors will unlock with every press of
UNLOCK on the remote keyless entry transmitter.Before your vehicle was shipped from the factory, it was
programmed in ALL. The mode to which the vehicle
has been programmed may have been changed since it
left the factory. To determine the mode to which your
vehicle is programmed or to program your vehicle to a
different mode, do the following:
1. Follow the instructions for ªEntering Programming
Modeº listed previously.
2. Press the MODE button until REMOTE DOOR
UNLOCK appears on the DIC.
3. Press the SET button until the arrow is before
DRIVER/ALL or ALL.
The mode you selected is now set. You can either exit
programming mode by following the instructions later in
this section or program the next feature available on
your vehicle.

2-118
Unlock Feedback
The unlock feedback feature can be programmed to one
of the following modes:
LIGHTS: This mode does the following:

During the day, when the ignition is in OFF and
UNLOCK on the remote keyless entry transmitter
is pressed, the headlamps and parking lamps will
flash, or

during the night, when the ignition is in OFF and the
headlamp exit delay feature is programmed to any
mode but OFF, the headlamps and parking lamps
will be activated for the same time period as the
headlamp exit delay feature is programmed to when
UNLOCK is pressed on the remote keyless entry
transmitter (see ªHeadlamp Exit Delayº earlier in
this section), or

during the night, when the ignition is in OFF and the
headlamp exit delay feature is programmed to OFF,
the headlamps and parking lamps will be activated
for 30 seconds when UNLOCK is pressed on the
remote keyless entry transmitter (see ªHeadlamp
Exit Delayº earlier in this section).OFF: The headlamps and parking lamps will not
flash when UNLOCK is pressed on the remote keyless
entry transmitter.
Before your vehicle was shipped from the factory, it was
programmed in LIGHTS. The mode to which the
vehicle has been programmed may have been changed
since it left the factory. To determine the mode to which
your vehicle is programmed or to program your vehicle
to a different mode, do the following:
1. Follow the instructions for ªEntering Programming
Modeº listed previously.
2. Follow the instructions for programming
HEADLAMP EXIT DELAY earlier in this section,
to make sure which mode it is programmed to.
3. Press the SET button until UNLOCK FEEDBACK
appears on the DIC.
4. Press the MODE button until the arrow is before
LIGHTS or OFF.
5. Press the SET button once you have determined
which mode you prefer.
The mode you selected is now set. You can either exit
programming mode by following the instructions later in
this section or program the next feature available on
your vehicle.

2-119
Lock Feedback
The lock feedback feature can be programmed to one of
the following modes:
OFF: When LOCK is pressed on the remote keyless
entry transmitter, the headlamps and parking lamps will
not flash and the horn will not sound.
LIGHTS: When LOCK is pressed on the remote
keyless entry transmitter, the headlamps and parking
lamps will flash briefly.
LIGHTS and HORN: When LOCK is pressed a
second time on the remote keyless entry transmitter
within five seconds, the headlamps and parking lamps
will flash briefly and the horn will sound.Before your vehicle was shipped from the factory, it was
programmed in LIGHTS and HORN. The mode to
which the vehicle has been programmed may have been
changed since it left the factory. To determine the mode
to which your vehicle is programmed or to program
your vehicle to a different mode, do the following:
1. Follow the instructions for ªEntering Programming
Modeº listed previously.
2. Press the MODE button until LOCK FEEDBACK
appears on the DIC.
3. Press the SET button until the arrow is before OFF,
LIGHTS or LIGHTS and HORN.
The mode you selected is now set. You can either exit
programming mode by following the instructions later in
this section or program the next feature available on
your vehicle.

2-120
Seat Recall
The seat recall feature can be programmed to one of the
following modes:
ON: The previously programmed memory seat position
will be recalled when the UNLOCK button is pressed on
the remote keyless entry transmitter.
OFF: No memory seat position will be recalled when
you press the UNLOCK button on the remote keyless
entry transmitter.
To determine the mode to which your vehicle is
programmed or to program your vehicle to a different
mode, do the following:
1. Follow the instructions for ªEntering Programming
Modeº listed previously.
2. Press the MODE button until SEAT RECALL
appears on the DIC.
3. Press the SET button until the arrow is before
ON or OFF.If the seat recall feature has been programmed to ON,
the seat recall feature can also be programmed to one of
the following modes:
MEMORY: The position recalled will be the memory
driving position.
EXIT: The position recalled will be the previously
programmed exit position.
To determine the mode to which your vehicle is
programmed or to program your vehicle to a different
mode, do the following:
1. Follow the instructions for ªEntering Programming
Modeº listed previously.
2. Follow the instructions for programming SEAT
RECALL to ON listed previously.
3. Press the MODE button until RECALL POSITION
appears on the DIC.
4. Press the SET button until the arrow is before
MEMORY or EXIT.
The mode you selected is now set. You can either exit
programming mode by following the instructions later in
this section or program the next feature available on
your vehicle.