BUICK RANDEZVOUS 2005 Owner's Manual

✍NOTES
3-3

Instrument Panel Overview
3-4

The main components of the instrument panel are the following:
A. Exterior/Interior Lamps Control. SeeExterior Lamps
on page 3-14andInterior Lamps on page 3-16.
B. Turn Signal/Multifunction Lever. SeeTurn
Signal/Multifunction Lever on page 3-7.
C. Hazard Warning Flasher Button. SeeHazard
Warning Flashers on page 3-6.
D. Instrument Panel Cluster. SeeInstrument Panel
Cluster on page 3-38.
E. Shift Lever. SeeAutomatic Transaxle Operation
on page 2-23.
F. Instrument Panel Outlets. SeeOutlet Adjustment
on page 3-36.
G. Audio System. SeeAudio System(s) on page 3-75.
H. Audio Steering Wheel Controls. SeeAudio
Steering Wheel Controls on page 3-133.
I. Head-Up Display Switch and Driver Information
Center (DIC) Controls (If Equipped). SeeHead-Up
Display (HUD) on page 3-21andDIC Controls
and Displays on page 3-64.J. Hood Release. SeeHood Release on page 5-11.
K. Ignition Switch. SeeIgnition Positions on page 2-20.
L. Climate Controls. SeeClimate Control System on
page 3-28,Dual Climate Control System on
page 3-30orDual Automatic Climate Control System
on page 3-33.
M. Instrument Panel Switchbank. SeeInstrument Panel
Switchbank on page 3-20.
N. Front Armrest Storage. SeeFront Armrest Storage
Area on page 2-40.
O. Ashtray/Cigarette Lighter/Accessory Power
Outlet/Cell Phone Storage/Cupholders. SeeAshtrays
and Cigarette Lighter on page 3-27,Accessory
Power Outlets on page 3-26,Cell Phone Storage
Area on page 2-39,Floor Console Storage Area on
page 2-39andCupholder(s) on page 2-39.
P. Floor Console Fuse Block. SeeFloor Console Fuse
Block on page 5-105.
Q. Glove Box. SeeGlove Box on page 2-38.
3-5

Hazard Warning Flashers
Your hazard warning ashers let you warn others. They
also let police know you have a problem. Your front
and rear turn signal lamps will ash on and off.
The hazard warning asher
button is located on top of
the steering column.
Your hazard warning ashers work no matter what
position your key is in, and even if the key is not in
the ignition.
Press the button to make the front and rear turn signal
lamps ash on and off. Press the button again to
turn the ashers off.
When the hazard warning ashers are on, your turn
signals will not work.
Other Warning Devices
If you carry reective triangles, you can set them up at
the side of the road about 300 feet (100 m) behind
your vehicle.
Horn
Press near or on the horn symbols on your steering
wheel pad to sound the horn.
Tilt Wheel
A tilt wheel allows you to adjust the steering wheel
before you drive. You can raise the steering wheel to
the highest level to give your legs more room when you
enter and exit the vehicle.
The lever that allows you to tilt the steering wheel is
located on the left side of the steering column.
To tilt the wheel, hold the
wheel and pull the lever.
Then move the wheel
to a comfortable position
and release the lever
to lock the wheel in place.
3-6

Turn Signal/Multifunction Lever
The lever on the left side of the steering column
includes the following:
GTurn and Lane-Change Signals. SeeTurn and
Lane-Change Signals on page 3-7.
3Headlamp High/Low-Beam Changer. See
Headlamp High/Low-Beam Changer on page 3-8.
Flash-to-Pass. SeeFlash-to-Pass on page 3-8.
WIPERNWindshield Wipers. SeeWindshield
Wipers on page 3-9.
LPUSHWindshield Washer. SeeWindshield
Washer on page 3-9.
CRUISEICruise Control. SeeCruise Control on
page 3-10.
Turn and Lane-Change Signals
The turn signal has two upward (for right) and two
downward (for left) positions. These positions allow you
to signal a turn or a lane change.
To signal a turn, move the lever all the way up or down.
When the turn is nished, the lever will return
automatically.
An arrow on the instrument
panel cluster and the HUD
display will ash in the
direction of the turn or lane
change.
To signal a lane change, just raise or lower the lever
until the arrow starts to ash. Hold it there until you
complete your lane change. The lever will return by itself
when you release it.
3-7

As you signal a turn or a lane change, if the arrow
ashes faster than normal, a signal bulb may be burned
out and other drivers will not see your turn signal.
If a bulb is burned out, replace it to help avoid an
accident. If the arrows do not go on at all when you
signal a turn, check for burned-out bulbs and check the
fuse. SeeFuses and Circuit Breakers on page 5-105.
If you have a trailer towing option with added wiring for
the trailer lamps, the signal indicator will ash at a
normal rate even if a turn signal bulb is burned
out. Check the front and rear turn signal lamps regularly
to make sure they are working.
Turn Signal On Chime
If either turn signal is left on for more than 3/4 mile
(1.2 km), a chime will sound to let the driver know to
turn it off.
If you need to leave the signal on for more than
3/4 mile (1.2 km), turn off the signal and then turn it
back on.
Headlamp High/Low-Beam Changer
To change the headlamps from low to high, push
the turn signal lever away from you, then release it. To
change the headlamps from high to low, pull the
lever toward you.
When the high beams are
on, this light on the
instrument panel cluster
and the HUD display (if
equipped), will also be on.
Flash-to-Pass
When the headlamps are off, pull the lever toward you
to momentarily turn on the high beams. This will
signal that you are going to pass. When you release the
lever, they will turn off.
3-8

Windshield Wipers
WIPERN:Turn the band marked WIPER to control
the windshield wipers.
MIST:For a single wiping cycle, turn the band to MIST.
Hold it there until the wipers start, then let go. The
wipers will stop after one cycle. If you want more cycles,
hold the band on MIST longer.
Delay:For delayed wiping cycles, you can set the
wiper speed for a long or short delay between wipes.
This can be very useful in light rain or snow. Turn
the band to choose the delay time. The closer to LO,
the shorter the delay time.
LO:For steady wiping cycles at low speed, turn the
band away from you to the LO position.
HI:For high-speed wiping, turn the band away from
you to the HI position.
OFF:To stop the wipers, turn the band to OFF.
Remember that damaged wiper blades may prevent you
from seeing well enough to drive safely. To avoid
damage, clear ice and snow from the wiper blades
before using them. If they are frozen to the windshield,
carefully loosen or thaw them. If your blades do
become damaged, get new blades or blade inserts.Heavy snow or ice can overload your wipers. A circuit
breaker will stop them until the motor cools. Clear away
snow or ice to prevent an overload.
Windshield Washer
LPUSH:To wash your windshield, press and hold
the paddle with the windshield washer symbol. The
washers and wipers will operate. When you release the
paddle, the washers will stop, and the wipers will
continue to operate for two cycles, unless your wipers
were already on. In that case, the wipers will resume the
wiper speed you selected earlier.
{CAUTION:
In freezing weather, do not use your washer
until the windshield is warmed. Otherwise the
washer uid can form ice on the windshield,
blocking your vision.
3-9

Rear Window Washer/Wiper
The rear window
washer/wiper switch is
located in the instrument
panel switchbank. See
Instrument Panel
Switchbank on page 3-20.
Z(Rear Intermittent Wiper) Press the wiper symbol on
the top of the switch to turn on the intermittent wiper. To
turn off the wiper, gently press the bottom of the switch.
=(Rear Wiper/Washer To wash and wipe the rear
window, press the washer symbol on the bottom of the
switch. Washer uid will spray as long as the switch is
held in. When the switch is released, the wiper will
continue to cycle three more times. There is only one
washer uid reservoir for the front and rear windshield
wipers. SeeWindshield Washer Fluid on page 5-37.
To wash the rear window while the rear wiper is already
on, press the bottom of the switch. Press the top of
the switch to continue the intermittent wiper cycle after
the washing cycle is completed.
Cruise Control
With cruise control, you can maintain a speed of about
25 mph (40 km/h) or more without keeping your foot
on the accelerator. This can really help on long trips.
Cruise control does not work at speeds below about
25 mph (40 km/h).
When you apply your brakes, the cruise control
disengages.
3-10

The cruise controls are
located on the end of the
turn signal/multifunction
lever.
ON:Move the switch to this position to turn the cruise
control system on.
R/A:Move the switch to this position to resume a set
speed or to accelerate.
SET:Press this button, located at the end of the lever,
to set a speed.
OFF:This position turns the cruise control system off
and cancels memory of a set speed.
{CAUTION:
Cruise control can be dangerous where you
cannot drive safely at a steady speed. So, do
not use your cruise control on winding roads
or in heavy traffic.
Cruise control can be dangerous on slippery
roads. On such roads, fast changes in tire
traction can cause needless wheel spinning,
and you could lose control. Do not use cruise
control on slippery roads.
If your vehicle is in cruise control when the traction
control system begins to limit wheel spin, the cruise
control will automatically disengage. SeeTraction
Control System (TCS) on page 4-10. When road
conditions allow you to safely use it again, you may turn
the cruise control back on.
3-11

Setting Cruise Control
{CAUTION:
If you leave your cruise control on when you
are not using cruise, you might hit a button
and go into cruise when you do not want to.
You could be startled and even lose control.
Keep the cruise control switch off until you
want to use cruise control.
1. Move the cruise control switch located on the turn
signal/multifunction lever, to ON.
2. Get up to the speed you want.
3. Press the SET button at the end of the lever and
release it.
4. Take your foot off the accelerator pedal.
Resuming a Set Speed
Suppose you set your cruise control at a desired speed
and then you apply the brake. This, of course, shuts
off the cruise control. But you do not need to reset
it. Once you are going about 25 mph (40 km/h) or more,
you can move the cruise control switch from ON to
Resume/Accelerate (R/A) briey.
You will go right back up to your chosen speed and
stay there.
If you hold the switch at R/A, the vehicle will keep going
faster until you release the switch or apply the brake.
So unless you want to go faster, do not hold the switch
at R/A.
Increasing Speed While Using Cruise
Control
There are two ways to increase speed while using
cruise control:
Use the accelerator pedal to get to the higher
speed. Press the SET button at the end of the lever,
then release the button and the accelerator pedal.
You will now cruise at the higher speed.
3-12