spare wheel BUICK RANDEZVOUS 2007 Owner's Manual

Windshield Wiper Blade Replacement....... 404
Tires............................................................ 406
Tire Sidewall Labeling............................... 407
Tire Terminology and Denitions............... 410
Ination - Tire Pressure............................. 413
Check Tire Pressure System..................... 414
Tire Inspection and Rotation...................... 416
When It Is Time for New Tires.................. 418
Buying New Tires...................................... 418
Different Size Tires and Wheels................ 420
Uniform Tire Quality Grading..................... 420
Wheel Alignment and Tire Balance............ 422
Wheel Replacement.................................. 422
Tire Chains............................................... 424
Accessory Inator...................................... 425
If a Tire Goes Flat.................................... 427
Changing a Flat Tire................................. 428
Removing the Spare Tire and Tools.......... 429
Removing the Flat Tire and Installing
the Spare Tire....................................... 436
Secondary Latch System........................... 441
Storing a Flat or Spare Tire and Tools.......... 444
Compact Spare Tire.................................. 450Appearance Care........................................ 451
Cleaning the Inside of Your Vehicle.......... 451
Fabric/Carpet............................................. 453
Leather...................................................... 454
Instrument Panel, Vinyl, and
Other Plastic Surfaces........................... 454
Care of Safety Belts.................................. 455
Weatherstrips............................................ 455
Washing Your Vehicle............................... 455
Cleaning Exterior Lamps/Lenses................ 456
Finish Care............................................... 456
Windshield, Backglass, and
Wiper Blades......................................... 457
Aluminum or Chrome-Plated Wheels......... 457
Tires......................................................... 458
Sheet Metal Damage................................. 458
Finish Damage.......................................... 459
Underbody Maintenance............................ 459
Chemical Paint Spotting............................ 459
Vehicle Care/Appearance Materials............ 460
Section 5 Service and Appearance Care
352

To reset the system, do the following:
1. With the engine off, turn the ignition to ON.
2. Press the MODE button until the DIC reads
LOW TIRE PRESSURE HOLD SET TO
RESET.
3. Press and hold the SET button until you hear
a chime, and TIRE PRESSURE RESET is
displayed.
You will hear three chimes, then the LOW TIRE
PRESSURE message will go off and the DIC
will return to TIRE PRESSURE NORMAL. If the
LOW TIRE PRESSURE message comes back on,
the check tire pressure system has not reset.
Repeat the procedure.
The system completes the calibration process
during driving. The system learns the pressure at
each tire throughout the operating speed range
of your vehicle. The system normally takes
between 30 and 60 minutes of driving to learn
the tire pressures. The system normally takes
10 to 20 minutes of driving in each speed range
to learn tire pressures. The speed ranges are
20 to 40 mph (32 to 64 km/h), 40 to 60 mph
(64 to 96 km/h), and above 60 mph (96 km/h).
This time may be longer depending on yourindividual driving habits. The learning process
does not need to be completed during a single trip.
Once learned, the system will remember the tire
pressure until the system is reset.
Tire Inspection and Rotation
Tires should be rotated every 5,000 to 8,000 miles
(8 000 to 13 000 km).
Any time you notice unusual wear, rotate your tires
as soon as possible and check wheel alignment.
Also check for damaged tires or wheels. SeeWhen
It Is Time for New Tires on page 418andWheel
Replacement on page 422for more information.
Make sure the spare tire is stored securely. Push,
pull, and then try to rotate or turn the tire, If it
moves, use the folding wrench to tighten the cable.
SeeStoring a Flat or Spare Tire and Tools on
page 444.
The purpose of regular rotation is to achieve
more uniform wear for all tires on the vehicle. The
rst rotation is the most important. SeeScheduled
Maintenance on page 475.
416

When rotating your tires, always use the correct
rotation pattern shown here.
Do not include the compact spare tire in your tire
rotation.
After the tires have been rotated, adjust the front
and rear ination pressures as shown on the
Tire and Loading Information label.
Reset the check tire pressure system, if equipped.
SeeCheck Tire Pressure System on page 414.Make certain that all wheel nuts are properly
tightened. See “Wheel Nut Torque” under
Capacities and Specications on page 469.
{CAUTION:
Rust or dirt on a wheel, or on the parts to
which it is fastened, can make wheel nuts
become loose after time. The wheel could
come off and cause an accident. When
you change a wheel, remove any rust or
dirt from places where the wheel attaches
to the vehicle. In an emergency, you can
use a cloth or a paper towel to do this;
but be sure to use a scraper or wire brush
later, if needed, to get all the rust or dirt
off. SeeChanging a Flat Tire on page 428.
417

If the tires have an all-season tread design, the
TPC spec number will be followed by an MS
for mud and snow. SeeTire Sidewall Labeling
on page 407for additional information.
{CAUTION:
Mixing tires could cause you to lose
control while driving. If you mix tires of
different sizes, brands, or types (radial and
bias-belted tires), the vehicle may not
handle properly, and you could have a
crash. Using tires of different sizes,
brands, or types may also cause damage to
your vehicle. Be sure to use the correct
size, brand, and type of tires on all wheels.
It is all right to drive with your compact
spare temporarily, as it was developed for
use on your vehicle. SeeCompact Spare
Tire on page 450.
{CAUTION:
If you use bias-ply tires on your vehicle,
the wheel rim anges could develop
cracks after many miles of driving. A tire
and/or wheel could fail suddenly, causing
a crash. Use only radial-ply tires with the
wheels on your vehicle.
If you must replace your vehicle’s tires with those
that do not have a TPC Spec number, make sure
they are the same size, load range, speed rating,
and construction type (radial and bias-belted tires)
as your vehicle’s original tires.
Your vehicle’s original equipment tires are listed on
the Tire and Loading Information Label. This label is
attached to the vehicle’s center pillar (B-pillar).
SeeLoading Your Vehicle on page 332, for more
information about the Tire and Loading Information
Label and its location on your vehicle.
419

Different Size Tires and Wheels
If you add wheels or tires that are a different size
than your original equipment wheels and tires, this
may affect the way your vehicle performs, including
its braking, ride and handling characteristics,
stability, and resistance to rollover. Additionally,
if your vehicle has electronic systems such as,
anti-lock brakes, traction control, and electronic
stability control, the performance of these systems
can be affected.
{CAUTION:
If you add different sized wheels, your
vehicle may not provide an acceptable
level of performance and safety if tires
not recommended for those wheels are
selected. You may increase the chance
that you will crash and suffer serious
injury. Only use GM specic wheel and
tire systems developed for your vehicle,
and have them properly installed by a GM
certied technician.SeeBuying New Tires on page 418and
Accessories and Modications on page 354
for additional information.
Uniform Tire Quality Grading
Quality grades can be found where applicable
on the tire sidewall between tread shoulder
and maximum section width. For example:
Treadwear 200 Traction AA Temperature A
The following information relates to the system
developed by the United States National Highway
Traffic Safety Administration (NHTSA), which
grades tires by treadwear, traction, and
temperature performance. This applies only to
vehicles sold in the United States. The grades are
molded on the sidewalls of most passenger car
tires. The Uniform Tire Quality Grading (UTQG)
system does not apply to deep tread, winter-type
snow tires, space-saver, or temporary use spare
tires, tires with nominal rim diameters of
10 to 12 inches (25 to 30 cm), or to some
limited-production tires.
420

When your vehicle has a at tire, use the following
example as a guide to assist you in the placement
of wheel blocks.
The following information will tell you next how to
use the jack and change a tire.Removing the Spare Tire and Tools
The equipment you will need is located in the
storage compartment on the passenger’s side,
at the rear of the vehicle.
1. Open the jack storage compartment by lifting
up the tab and pulling the cover off.
429

A. Hoist Shaft
B. Folding Wrench
C. Hoist AssemblyD. Retainer
E. Compact Spare Tire
1. Flip the rear cargo area carpet cut out to
expose the hoist shaft.
2. Attach the folding wrench into the hoist shaft.
3. Turn the folding wrench counterclockwise
to lower the spare tire to the ground.
Continue turning the wrench until the spare
tire can be pulled out from under the vehicle.4. Tilt the retainer and slip it through the wheel
opening to remove the spare tire from the
cable.
5. Turn the wrench clockwise to raise the cable
back up after removing the spare tire.
Do not store a full-size or a at road tire under
the vehicle. SeeStoring a Flat or Spare Tire
and Tools on page 444.
To continue changing the at tire, seeRemoving
the Flat Tire and Installing the Spare Tire on
page 436.
431

5. Tilt the retainer and slip it through the wheel
opening to remove the spare tire from the
cable.
6. Turn the wrench clockwise to raise the cable
back up after removing the spare tire.
Do not store a full-size or a at road tire under
the vehicle. SeeStoring a Flat or Spare Tire
and Tools on page 444.
To continue changing the at tire, seeRemoving
the Flat Tire and Installing the Spare Tire on
page 436.If the spare tire will not lower, the secondary latch
may be engaged causing the tire not to lower.
434

Removing the Flat Tire and
Installing the Spare Tire
1. If there is a wheel cover, loosen the plastic
nut caps with the wheel wrench. They will
not come off. Then, using the at end of the
wheel wrench, pry along the edge of the cover
until it comes off. Be careful; the edges may
be sharp. Do not try to remove the cover
with your bare hands.
If your vehicle has aluminum wheels, remove
the wheel nut caps using the wheel wrench.2. Loosen the wheel nuts, but do not remove
them, using the folding wrench.
Turn the handle about 180 degrees, then ip
the handle back to the starting position. This
avoids taking the wrench off the lug nut for each
turn. For wheels with a wheel lock key, use the
wheel lock key between the lock nut and folding
wrench. The key is supplied in the front
passenger door pocket.
Notice:If your vehicle has wheel locks and you
use an impact wrench to remove the wheel nuts,
you could damage the lock nut or wheel lock
key. Do not use an impact wrench to remove the
wheel nuts if your vehicle has wheel locks.
436

3. Locate the notch
(A is 3.0 inches
(7.5 cm) from the
front tire or B is
5.5 inches (14.0 cm)
from the rear tire).
The notch is located
near each wheel in
the vehicle’s body.
Notice:If you use a jack to raise the vehicle
without positioning it correctly, you could
damage your vehicle. When raising your vehicle
on a jack, avoid contact with the rear axle
control arms.
Do not raise the vehicle yet. Put the compact
spare tire near you.
{CAUTION:
Getting under a vehicle when it is jacked
up is dangerous. If the vehicle slips off
the jack you could be badly injured or
killed. Never get under a vehicle when
it is supported only by a jack.
437