buttons CADILLAC CTS 2008 2.G Owner's Guide

To connect and control your iPod, connect one end of
the specially purchased iPod connection cable to
the iPod’s dock connector. Connect the other end to
both the USB port and the auxiliary input jack. The USB
port and the auxiliary input jack are located in the
center console bin. If the vehicle is on and the USB
connection works, you will see a GM logo appear
on your iPod. Your iPod music will display on your
radio’s display and begin playing through your vehicle
radio system.
A standard iPod USB cable, like the one that came with
your iPod, cannot be used to connect an iPod to your
vehicle. You must use the iPod connection cable
that was purchased with your vehicle or that was made
available from your dealer/retailer in order for this
feature to work.
Use the radio Menu/Select knob to bring up the iPod
Menu and select Songs, Artists, Albums, Playlists
and Audio books to play from your iPod.Your iPod will charge while it is connected to
your vehicle and if your vehicle is turned to ACC/
ACCESSORY or ON/RUN. It can also be left connected
to your vehicle while the vehicle is turned off or removed.
With the vehicle turned off, the iPod will automatically be
powered off and will not charge or draw power from the
vehicle’s battery.
If you have an older iPod model that is not supported or
do not have the special iPod connection cable, you
can still listen to your iPod in your vehicle by connecting
it to the Auxiliary Input Jack using a standard 3.5 mm
(1/8 inch) stereo cable. See “Using the Auxiliary
Input Jack” earlier for more information.
Press the AM/FM, XM or HDD buttons to listen to one
of these sources while an iPod is connected. If a disc is
inserted, press the CD/AUX button to listen to a CD
or DVD-A disc. Press the CD/AUX button again to start
playing and controlling the connected iPod.
To properly dismount the iPod USB device before
disconnecting from the vehicle, press the button directly
under the EJECT label found on the iPod playback
screen.
3-105

Playlists can be selected by using the previous and next
folder buttons, the SEEK arrows,
\FWD, orsREV
buttons. An MP3/WMA CD-R or CD-RW that was
recorded using no le folders can also be played. If a
CD-R or CD-RW contains more than the maximum of
50 folders and playlists, and 255 les, the player lets you
access and navigate up to the maximum, but all items
over the maximum are not accessible.
The HDD Radio can support more than 255 les on an
MP3/WMA disc.
The HDD Radio does not support playlists on a disc or
USB storage device.
Root Directory
The root directory of the CD-R or CD-RW is treated as
a folder. If the root directory has compressed audio
les, the directory displays as F1 DISC. All les
contained directly under the root directory are accessed
prior to any root directory folders. Playlists (Px) are
always accessed after root folders or les.
The HDD Radio displays the root directory of an
MP3/WMA disc as F1 MP3 and the root directory of a
USB storage device as F1 USB.
Empty Directory or Folder
If a root directory or a folder exists somewhere in the
le structure that contains only folders/subfolders and
no compressed les directly beneath them, the
player advances to the next folder in the le structure
that contains compressed audio les.
No Folder
When the CD contains only compressed les, the les
are located under the root folder. The next and previous
folder functions do not display on a CD that was
recorded without folders or playlists. The radio displays
F1 DISC for the root directory.
When the CD contains only playlists and compressed
audio les, but no folders, all les are located under the
root folder. The folder down and the folder up buttons
search playlists (Px) rst and then goes to the root
folder. The radio displays F1 DISC for the root directory.
3-107

Order of Play
Tracks recorded to the CD-R or CD-RW play in the
following order:
Play begins from the rst track in the rst folder
and continues sequentially through all tracks in
each folder. When the last track of the last folder
has played, play continues from the rst track of the
rst playlist.
Playlists can be changed by pressing the next
and previous folder button.
Play begins from the rst track in the rst playlist and
continues sequentially through all tracks in each
playlist. When the last track of the last playlist has
played, play continues from the rst track of the rst
folder.
When play enters a new folder, the display does not
automatically show the new folder name unless the
folder mode has been chosen as the default display.
The new track name displays.
File System and Naming
The song name displays the song name that is contained
in the ID3 tag. If the song name is not in the ID3 tag,
the radio displays the le name without the extension.
Track names longer than 32 characters are shortened.
Parts of words on the last page of text and the
extension of the lename is not displayed.
The HDD Radio will display le names with the
extension.
Preprogrammed Playlists
Preprogrammed playlists that were created using
WinAmp™, MusicMatch™, or Real Jukebox™ software
can be accessed, however they cannot be edited
using the radio. These playlists are special folders
containing compressed audio song les. Playlists must
have a le extension of PLS or M3U.
Playlists can be selected using the previous and next
folder buttons. Tracks can be changed by pressing
the seek buttons or turning the tune knob. Songs are
played sequentially; press the
sREV or\FWD
to reverse or advance through the playing song.
3-108

The HDD Radio does not support preprogrammed
playlists. To create a playlist on the HDD radio from
songs recorded to the HDD, see “Saving HDD Favorites”
earlier in this section.
Playing an MP3/WMA
Insert a CD partway into the slot (Single CD Player),
or press the load button and wait for the message
to insert disc (Six-Disc CD Player), label side up.
The player pulls in the CD and should begin playing.
For the Single CD Player, the track number displays
at the left and center of the screen. A Shuffle label
appears below. Press the pushbutton located under the
Shuffle label to play the MP3/WMA les of the CD in
random order.
For the Six-Disc CD Player, the disc number displays at
the upper right side of the screen. The track number
displays at the left and center of the screen. The Shuffle,
Disc, and Folder labels appear below. Press the
pushbutton located under the Shuffle label to play the
MP3/WMA les of the currently selected CD in random
order. Press the pushbuttons located under the Disc
or Folder labels to change to another disc or folder.As each new track starts to play, the track number and
song title displays.
Z(Eject):Press to eject a CD. If the CD is not
removed, after several seconds, the CD automatically
pulls back into the player and begins playing.
For the Six-Disc CD player, press and hold this button
for two seconds to eject all discs.
TUNE/TONE:Turn to select MP3/WMA les on the
CD playing.
©SEEK¨:Press the left arrow to go to the start of
the current MP3/WMA le, if more than ve seconds
have played. Press the right arrow to go to the
next MP3/WMA le. If either arrow is held or pressed
multiple times, the player continues moving backward
or forward through MP3/WMA les on the CD.
Sc(Previous Folder):Press the pushbutton under
the Folder label to go to the rst track in the previous
folder.
cT(Next Folder):Press the pushbutton under the
Folder label to go to the rst track in the next folder.
3-109

Audio System
When using the in-vehicle Bluetooth system, sound
comes through the vehicle’s front audio system speakers
and over-rides the audio system. Use the audio
system volume knob, during a call, to change the
volume level. The adjusted volume level remains in
memory for later calls. To prevent missed calls, a
minimum volume level is used if the volume is turned
down too low.
Bluetooth Controls
Use the buttons located on the steering wheel to
operate the in-vehicle Bluetooth system. SeeAudio
Steering Wheel Controls on page 3-124for more
information.
bg(Push To Talk):Press to answer incoming calls,
to conrm system information, and to start speech
recognition.
cª(Phone On Hook):Press to end a call, reject a
call, or to cancel an operation.
Pairing
A Bluetooth enabled cell phone must be paired to the
in-vehicle Bluetooth system rst and then connected to
the vehicle before it can be used. See the cell phone
manufacturers user guide for Bluetooth functions before
pairing the cell phone. If a Bluetooth phone is not
connected, calls will be made using OnStar
®hands free
calling, if available. Refer to the OnStar owners guide
for more information.
Pairing Information:
Up to ve cell phones can be paired to the in-vehicle
Bluetooth system.
The pairing process is disabled when the vehicle is
moving.
The in-vehicle Bluetooth system automatically links
with the rst available paired cell phone in the
order the phone was paired.
Only one paired cell phone can be connected to the
in-vehicle Bluetooth system at a time.
Pairing should only need to be completed once,
unless changes to the pairing information have
been made or the phone is deleted.
To link to a different paired phone, see Linking to a
Different Phone later in this section.
3-112

TPMS Sensor Matching Process
Each TPMS sensor has a unique identication code.
Any time you replace one or more of the TPMS sensors
or rotate your vehicle’s tires, the identication codes
need to be matched to the new tire/wheel position.
The sensors are matched to the tire/wheel positions
in the following order: driver side front tire, passenger
side front tire, passenger side rear tire, and driver
side rear tire using a TPMS diagnostic tool. See your
dealer/retailer for service.
The TPMS sensors can also be matched to each
tire/wheel position by increasing or decreasing the tire’s
air pressure. If increasing the tire’s air pressure, do not
exceed the maximum ination pressure indicated on the
tire’s sidewall. To decrease the tire’s air-pressure use the
pointed end of the valve cap, a pencil-style air pressure
gage, or a key.
You have two minutes to match the rst tire/wheel
position, and ve minutes overall, to match all four
tire/wheel positions. If it takes longer than two minutes,
to match the rst tire and wheel, or more than
ve minutes to match all four tire and wheel positions,
the matching process stops and you need to start over.The TPMS matching process is outlined below:
1. Set the parking brake.
2. Turn the ignition switch to ON/RUN with the
engine off.
3. Press the Remote Keyless Entry (RKE) transmitter’s
lock and unlock buttons at the same time for
approximately ve seconds. The horn sounds twice
to signal the receiver is in relearn mode and Tire
Learning Active message displays on the DIC
screen.
4. Start with the driver side front tire.
5. Remove the valve cap from the valve stem.
Activate the TPMS sensor by increasing or
decreasing the tire’s air pressure for 10 seconds,
or until a horn chirp sounds. The horn chirp, which
can take up to 30 seconds to sound, conrms
that the TPMS sensor identication code has
been matched to this tire position.
6. Proceed to the passenger side front tire, and repeat
the procedure in Step 5.
7. Proceed to the passenger side rear tire, and repeat
the procedure in Step 5.
8. Proceed to the driver side rear tire, and repeat the
procedure in Step 5.
5-73

Appearance Care
Interior Cleaning
Your vehicle’s interior will continue to look its best if it is
cleaned often. Although not always visible, dust and dirt
can accumulate on your upholstery. Dirt can damage
carpet, fabric, leather, and plastic surfaces. Regular
vacuuming is recommended to remove particles from
your upholstery. It is important to keep your upholstery
from becoming and remaining heavily soiled. Soils should
be removed as quickly as possible. Your vehicle’s interior
may experience extremes of heat that could cause stains
to set rapidly.
Lighter colored interiors may require more frequent
cleaning. Use care because newspapers and garments
that transfer color to your home furnishings may also
transfer color to your vehicle’s interior.
When cleaning your vehicle’s interior, only use cleaners
specically designed for the surfaces being cleaned.
Permanent damage may result from using cleaners on
surfaces for which they were not intended. Use glass
cleaner only on glass. Remove any accidental over-spray
from other surfaces immediately. To prevent over-spray,
apply cleaner directly to the cleaning cloth.Notice:If you use abrasive cleaners when cleaning
glass surfaces on your vehicle, you could scratch
the glass and/or cause damage to the rear window
defogger. When cleaning the glass on your
vehicle, use only a soft cloth and glass cleaner.
Many cleaners contain solvents that may become
concentrated in your vehicle’s breathing space.
Before using cleaners, read and adhere to all safety
instructions on the label. While cleaning your vehicle’s
interior, maintain adequate ventilation by opening
your vehicle’s doors and windows.
Dust may be removed from small buttons and knobs
using a small brush with soft bristles.
Your dealer/retailer has a product for cleaning your
vehicle’s glass. Should it become necessary, you can
also obtain a product from your dealer/retailer to remove
odors from your vehicle’s upholstery.
5-112