key CADILLAC CTS V 2007 1.G Service Manual

See “Activating Category (CAT) Stations (RDS
and XM™)” underRadio with CD on page 260for
more information.
ASEEK LOCAL/DISTANT:This feature instructs
the audio system to seek only local radio stations
with the strongest signal or to seek all radio stations
with a strong signal in a large area. Use LOCAL
when you are in urban areas where there are
several strong radio station signals and you want to
limit the number of stations to those with the
strongest signals only. Use DISTANT when you are
in rural areas where there are fewer radio station
signals available.
To switch between LOCAL and DISTANT, press
the TUNE/SEL knob. Once your choice is
displayed, turn the knob to set your choice and
continue scrolling through the main menu.
9(English/Metric Units):Use this menu item
to adjust the measurement units.
You can choose between ENGLISH UNITS and
METRIC UNITS. To switch between the two, press
the TUNE/SEL knob. Once your choice is
displayed, turn the knob to set your choice and
continue scrolling through the main menu.The measurement units that you choose will be
reected on all the vehicle system displays,
not just the DIC information. For example, the
climate control panel will display degrees Celsius
if you choose METRIC UNITS.
TCS (Traction Control System):You can enable
or disable the Traction Control System (TCS)
using this menu item. Press the TUNE/SEL knob
to switch between on and off.
You can also turn the TCS off using the traction
control button located in the glove box (CTS) or on
the steering wheel (CTS-V), or by programming
one of the steering wheel controls (1, 2, 3, or 4) or
audio system soft keys to enable/disable the
TCS. SeeRecongurable Steering Wheel Controls
(SWC) (CTS) on page 169and “Congurable
Radio Display Keys” underRadio with CD
on page 260for more information.
When you disable the TCS, the traction control
system warning light on the instrument panel
cluster will come on. SeeTraction Control System
(TCS) Warning Light on page 206for more
information.
231

8(Clock):Use this menu item to set the time on
the clock.
SeeSetting the Time on page 259for more
information.
8/4(Clock/Information Display):Use this
menu item to toggle between the clock display and
the XM™ Information (Song, Artist, Album), if
available.
SeeSetting the Time on page 259and “XM™
Satellite Radio Service” underRadio with CD on
page 260for more information.
SETUP:When you select this menu item, the
following submenu is available:
LANGUAGE
PERSONALIZATION
CONFIGURE DISPLAY KEYS
CONFIGURE SWC (Steering Wheel
Control) KEYS
To change the language displayed on the radio,
select LANGUAGE by pressing the TUNE/SEL
knob. Turn the TUNE/SEL knob to scroll through
the available languages and press the knob tomake your selection. If you accidentally select a
language that you did not want, ENGLISH is
always at the top of the language list.
For more information on the other items in the
SETUP menu, seeDIC Vehicle Personalization on
page 242andRecongurable Steering Wheel
Controls (SWC) (CTS) on page 169.
DIC Warnings and Messages
These messages will appear if there is a problem
detected in one of your vehicle’s systems.
You must acknowledge a message to clear it from
the screen for further use. To clear a message,
press the CLR button.
Be sure to take any message that appears on the
screen seriously and remember that clearing
the message will only make the message
disappear, not the problem.
Battery Not Charging
When this message appears on the display, there
is a problem with the generator and battery
charging systems. Have the electrical system
checked by your dealer as soon as possible.
232

Stability System Off
If your vehicle has StabiliTrak®, this message will
be displayed any time you turn off StabiliTrak®
using the TC (traction control) on/off button.
SeeTraction Control System (TCS) (CTS) on
page 293orTraction Control System (TCS)
(CTS-V) on page 295for more information. When
this message has been displayed, StabiliTrak
®
is no longer available to assist you with directional
control of the vehicle. Adjust your driving
accordingly.
Stability System Ready
If your vehicle has StabiliTrak®, this message will
be displayed any time you turn StabiliTrak®on
again using the TC (traction control) on/off button.
SeeTraction Control System (TCS) (CTS) on
page 293orTraction Control System (TCS)
(CTS-V) on page 295for more information. When
this message has been displayed, StabiliTrak
®
is ready to assist you with directional control of the
vehicle, if needed.
Starting Disabled – Remove Key
This message will appear when the vehicle
theft-deterrent system detects that an improper
ignition key is being used to try to start the vehicle.
Check the ignition key for damage. If it is
damaged, it may need to be replaced. If it is not
damaged, remove the key and try to start the
vehicle again. If it still does not start, try another
ignition key or have your vehicle serviced by
your dealer.
Starting Disabled – Throttle Problem
This message appears when your vehicle’s throttle
system is not functioning properly. Have your
vehicle serviced by your dealer.
Theft Attempted
This message is displayed if the content
theft-deterrent system has detected a break-in
attempt while you were away from your vehicle.
241

On all vehicles, features such as climate control
settings, radio preset settings, exterior lighting
at unlock, remote lock and unlock conrmation,
and automatic door locks have already been
programmed for your convenience.
Some vehicles have additional features that can
be programmed including the seat and outside
rearview mirror position.
If your vehicle has the ability to program additional
personalization features, the driver’s preferences
are recalled by pressing the unlock button on
the Remote Keyless Entry (RKE) transmitter,
1 or 2, or by pressing the appropriate memory
button, 1 or 2, located on the driver’s door. Certain
features can be programmed not to recall until
the key is placed in the ignition. To change feature
preferences, see “Entering the Personalization
Menu” following.Entering the Personalization Menu
To enter the feature programming mode, use the
following procedure:
1. Turn the ignition to ON, but do not start the
engine. Make sure an automatic transmission
is in PARK (P) or a manual transmission
has the parking brake set.
To avoid excessive drain on the battery, it is
recommended that the headlamps are
turned off.
2. If your vehicle has memory settings, press the
appropriate memory button, 1 or 2, located on
the driver’s door armrest. The DIC display
will show either Driver 1 or 2 depending
on which button was selected.
3. Press the PWR/VOL knob to turn the radio on.
4. Press the TUNE/SEL knob once to access the
main menu of the DIC.
5. Turn the TUNE/SEL knob until SETUP is
highlighted.
243

6. Press the TUNE/SEL knob once to access the
SETUP menu.
7. Turn the TUNE/SEL knob until the feature you
want to change is highlighted, then press the
TUNE/SEL knob to turn the feature on or
off. If the feature is turned on, a check mark
will appear next to the feature name.
If none of the personalization items are turned
on, turn on the personalization menu by
pressing the TUNE/SEL knob. The list of
features will then appear, and you can repeat
Step 6.
Personalization Features
The following choices are available for
programming:
Personalization Name
This feature allows you to type in a name that will
appear on the DIC display whenever the
corresponding Remote Keyless Entry (RKE)
transmitter is used or one of the buttons on the
driver’s door armrest (1 or 2) is pressed.If a customized name is not programmed, the
system will show DRIVER 1 or DRIVER 2
to correspond with the numbers on the back of the
RKE transmitters.
To program a name, use the following procedure:
1. Enter the Personalization menu following
the instructions listed previously.
2. Select the PERSONALIZATION NAME menu
item by pressing the TUNE/SEL knob once.
You will see a cursor on the screen.
3. Turn the TUNE/SEL knob until you reach the
rst letter you want. The letter will be
highlighted. There is a complete alphabet with
both upper and lower case letters and the
numbers zero through nine. Also included are
spaces and other non-letter characters
such as the ampersand (&).
244

4. Press the TUNE/SEL knob once to select the
letter. The letter will then appear on the display.
If you make a mistake, press the CLR button.
This will exit the menu. You can then go
back into the menu and edit the name. You
can also press the TUNE/SEL knob repeatedly
to cycle through all the characters until you
reach the character you wish to change.
5. Repeat Steps 3 and 4 until the name you
want is complete. You can program up to
16 characters.
The name you selected is now set. You can either
exit the programming mode by following the
instructions later in this section or program the
next feature available on your vehicle. To program
the next feature, enter the personalization
portion of the SETUP menu following the
instructions listed previously.
Congure Display Keys
This feature allows you to customize the functions
of the four soft keys located to the left and right
of the audio display. See “Congurable Radio
Display Keys” underRadio with CD on page 260
for programming information.
Congure SWC (Steering Wheel
Controls) Keys
This feature allows you to customize the functions
of the four steering wheel controls located on
the left spoke of the steering wheel. See
Recongurable Steering Wheel Controls (SWC)
(CTS) on page 169for programming information.
Remote Recall Memory
If your vehicle has the optional memory package,
you will have this feature. When this feature is
turned on, you can recall any previously
programmed seat and mirror controls when the
unlock button on the Remote Keyless Entry (RKE)
transmitter is pressed.
Programmable Modes
Mode 1:ON
Mode 2:OFF
Before your vehicle was shipped from the factory,
it was programmed to Mode 2. The mode to
which the vehicle was programmed may have
been changed since it left the factory.
245

To program the vehicle to a different mode, use
the following procedure:
1. Enter the personalization portion of the
SETUP menu following the instructions
listed previously.
2. Turn the TUNE/SEL knob until REMOTE
RECALL MEMORY is highlighted.
3. Press the TUNE/SEL knob to switch back and
forth between on and off.
When the mode is turned on, a check mark
will appear next to the feature name.
If this feature is selected, Remote Exit Recall or
Key In Recall Memory cannot be selected.
The mode you selected is now set. You can either
exit the programming mode by following the
instructions later in this section or program the
next feature available on your vehicle.
Remote Exit Recall
If your vehicle has the optional memory package,
you will have this feature. When this feature is
turned on, you can recall any previously
programmed exit position for the driver’s seat
when the unlock button on the Remote Keyless
Entry (RKE) transmitter is pressed.Programmable Modes
Mode 1:ON
Mode 2:OFF
Before your vehicle was shipped from the factory,
it was programmed to Mode 2. The mode to
which the vehicle was programmed may have
been changed since it left the factory.
To program the vehicle to a different mode, use
the following procedure:
1. Enter the personalization portion of the
SETUP menu following the instructions
listed previously.
2. Turn the TUNE/SEL knob until REMOTE EXIT
RECALL is highlighted.
3. Press the TUNE/SEL knob to switch back and
forth between on and off.
When the mode is turned on, a check mark
will appear next to the feature name.
If this feature is selected, Remote Recall Memory
cannot be selected.
The mode you selected is now set. You can either
exit the programming mode by following the
instructions later in this section or program the
next feature available on your vehicle.
246

Key in Recall Memory
If your vehicle has the optional memory package,
you will have this feature. When this feature is
turned on, you can recall any previously
programmed seat and mirror positions when the
key is inserted into the ignition.
Programmable Modes
Mode 1:ON
Mode 2:OFF
Before your vehicle was shipped from the factory,
it was programmed to Mode 2. The mode to
which the vehicle was programmed may have
been changed since it left the factory.
To program the vehicle to a different mode, use
the following procedure:
1. Enter the personalization portion of the
SETUP menu following the instructions
listed previously.
2. Turn the TUNE/SEL knob until KEY IN
RECALL MEMORY is highlighted.3. Press the TUNE/SEL knob to switch back and
forth between on and off.
When the mode is turned on, a check mark
will appear next to the feature name.
If this feature is selected, Remote Recall Memory
cannot be selected.
The mode you selected is now set. You can either
exit the programming mode by following the
instructions later in this section or program the
next feature available on your vehicle.
Auto Exit Seat
If your vehicle has the optional memory package,
you will have this feature. When this feature is
turned on, you can recall any previously
programmed exit position for the driver’s seat
when the key is removed from the ignition and the
driver’s door is opened.
247

To determine the mode to which the vehicle is
programmed or to program the vehicle to a
different mode, use the following procedure:
1. Enter the personalization portion of the
SETUP menu following the instructions
listed previously.
2. Turn the TUNE/SEL knob until TWILIGHT
DELAY is highlighted.
3. Press the TUNE/SEL knob to scroll through
and select the available delay settings.
If you choose Mode 1, the exterior lamps will
not illuminate when you exit the vehicle.
Only one mode can be selected at a time.
The mode you selected is now set. You can either
exit the programming mode by following the
instructions later in this section or program the
next feature available on your vehicle.
Lights Flash at Unlock
This feature ashes the exterior lamps when the
Remote Keyless Entry (RKE) transmitter is used to
unlock the vehicle. The lamps will ash for about
20 seconds unless a door is opened, the ignition is
turned to ACCESSORY, ON, or START, or the RKE
transmitter is used to lock the vehicle.Programmable Modes
Mode 1:ON
Mode 2:OFF
Before your vehicle was shipped from the factory,
it was programmed to Mode 1. The mode to
which the vehicle was programmed may have
been changed since it left the factory.
To program the vehicle to a different mode, use
the following procedure:
1. Enter the personalization portion of the
SETUP menu following the instructions
listed previously.
2. Turn the TUNE/SEL knob until LIGHTS
FLASH AT UNLOCK is highlighted.
3. Press the TUNE/SEL knob to switch back and
forth between on and off.
When the mode is turned on, a check mark
will appear next to the feature name.
The mode you selected is now set. You can either
exit the programming mode by following the
instructions later in this section or program the
next feature available on your vehicle.
249

Lights Flash at Lock
This feature allows the exterior lamps to ash
once when the Remote Keyless Entry (RKE)
transmitter is used to lock the vehicle. All doors
must be closed for this feature to work, and
the lamps will not ash if the parking lamps or
headlamps are on.
Programmable Modes
Mode 1:ON
Mode 2:OFF
Before your vehicle was shipped from the factory,
it was programmed to Mode 1. The mode to
which the vehicle was programmed may have
been changed since it left the factory.
To program the vehicle to a different mode, use
the following procedure:
1. Enter the personalization portion of the
SETUP menu following the instructions
listed previously.
2. Turn the TUNE/SEL knob until LIGHTS
FLASH AT LOCK is highlighted.3. Press the TUNE/SEL knob to switch back and
forth between on and off.
When the mode is turned on, a check mark
will appear next to the feature name.
You can select this feature by itself, or you can
combine it with Horn Sounds At Lock so that both
the lights ash and the horn chirps when you
lock your vehicle.
The mode you selected is now set. You can either
exit the programming mode by following the
instructions later in this section or program the
next feature available on your vehicle.
Horn Sounds at Lock
This feature sounds the horn once when the
Remote Keyless Entry (RKE) transmitter is used
to lock the vehicle. All doors must be closed
for this feature to work.
Programmable Modes
Mode 1:ON
Mode 2:OFF
Before your vehicle was shipped from the factory,
it was programmed to Mode 2. The mode to
which the vehicle was programmed may have
been changed since it left the factory.
250