key CADILLAC CTS V 2007 1.G Workshop Manual

To program the vehicle to a different mode, use
the following procedure:
1. Enter the personalization portion of the
SETUP menu following the instructions
listed previously.
2. Turn the TUNE/SEL knob until HORN
SOUNDS AT LOCK is highlighted.
3. Press the TUNE/SEL knob to switch back and
forth between on and off.
When the mode is turned on, a check mark
will appear next to the feature name.
If you select this feature to be on, Lights Flash At
Lock will also be on. You can choose Lights
Flash At Lock by itself, but Horn Sounds At Lock
will always have Lights Flash At Lock enabled
when it is selected.
The mode you selected is now set. You can either
exit the programming mode by following the
instructions later in this section or program the
next feature available on your vehicle.Exterior Lights at Unlock
This feature turns on the exterior lamps when the
Remote Keyless Entry (RKE) transmitter is
used to unlock the vehicle. The lamps will remain
on for about 20 seconds unless a door is
opened, the ignition is turned to ACCESSORY,
ON, or START, or the RKE transmitter is used to
lock the vehicle.
Programmable Modes
Mode 1:ON
Mode 2:OFF
Before your vehicle was shipped from the factory,
it was programmed to Mode 1. The mode to
which the vehicle was programmed may have
been changed since it left the factory.
To program the vehicle to a different mode, use
the following procedure:
1. Enter the personalization portion of the
SETUP menu following the instructions
listed previously.
2. Turn the TUNE/SEL knob until EXT. LIGHT
AT UNLOCK is highlighted.
251

3. Press the TUNE/SEL knob to switch back and
forth between on and off.
When the mode is turned on, a check mark
will appear next to the feature name.
The mode you selected is now set. You can either
exit the programming mode by following the
instructions later in this section or program the
next feature available on your vehicle.
Driver Unlock in Park
(Automatic Transmission Only)
The feature allows the driver’s door to
automatically unlock when the transmission is
shifted into PARK (P).
Programmable Modes
Mode 1:ON
Mode 2:OFF
Before your vehicle was shipped from the factory,
it was programmed to Mode 2. The mode to
which the vehicle was programmed may have
been changed since it left the factory.To program the vehicle to a different mode, use
the following procedure:
1. Enter the personalization portion of the
SETUP menu following the instructions
listed previously.
2. Turn the TUNE/SEL knob until DRIVER
UNLOCK IN PARK is highlighted.
3. Press the TUNE/SEL knob to switch back and
forth between on and off.
When the mode is turned on, a check mark
will appear next to the feature name.
If this feature is selected, Driver Unlock Key
Out/Off, Doors Unlock Key Out/Off, or Doors
Unlock in Park cannot be selected.
The mode you selected is now set. You can either
exit the programming mode by following the
instructions later in this section or program the
next feature available on your vehicle.
252

Driver Unlock Key Out (Automatic
Transmission Only)/Driver Unlock Key Off
(Manual Transmission Only)
This feature allows the driver’s door to
automatically unlock when the key is removed
from the ignition on automatic transmission
vehicles or when the ignition is turned to OFF for
manual transmission vehicles.
Programmable Modes
Mode 1:ON
Mode 2:OFF
Before your vehicle was shipped from the factory,
it was programmed to Mode 2. The mode to
which the vehicle was programmed may have
been changed since it left the factory.To program the vehicle to a different mode, use
the following procedure:
1. Enter the personalization portion of the
SETUP menu following the instructions
listed previously.
2. Turn the TUNE/SEL knob until DRIVER
UNLOCK KEY OUT/OFF is highlighted.
3. Press the TUNE/SEL knob to switch between
on and off.
When the mode is turned on, a check mark
will appear next to the feature name.
If this feature is selected, Driver Unlock in Park
(automatic transmission), Doors Unlock in
Park (automatic transmission), or Doors Unlock
Key Out/Off cannot be selected.
The mode you selected is now set. You can either
exit the programming mode by following the
instructions later in this section or program the
next feature available on your vehicle.
253

Doors Unlock in Park
(Automatic Transmission Only)
The feature allows the doors to automatically
unlock when the transmission is shifted into
PARK (P).
Programmable Modes
Mode 1:ON
Mode 2:OFF
Before your vehicle was shipped from the factory,
it was programmed to Mode 2. The mode to
which the vehicle was programmed may have
been changed since it left the factory.
To program the vehicle to a different mode, use
the following procedure:
1. Enter the personalization portion of the
SETUP menu following the instructions
listed previously.
2. Turn the TUNE/SEL knob until DOORS
UNLOCK IN PARK is highlighted.
3. Press the TUNE/SEL knob to switch back and
forth between on and off.
When the mode is turned on, a check mark
will appear next to the feature name.If this feature is selected, Doors Unlock Key
Out/Off, Driver Unlock Key Out/Off, or Driver Unlock
in Park (automatic transmission) cannot be
selected.
The mode you selected is now set. You can either
exit the programming mode by following the
instructions later in this section or program the
next feature available on your vehicle.
Doors Unlock Key Out (Automatic
Transmission Only)/ Doors Unlock Key Off
(Manual Transmission Only)
This feature allows the doors to automatically
unlock when the key is removed from the ignition
on automatic transmission vehicles or when
the ignition is turned to OFF on manual
transmission vehicles.
Programmable Modes
Mode 1:ON
Mode 2:OFF
Before your vehicle was shipped from the factory,
it was programmed to Mode 2. The mode to
which the vehicle was programmed may have
been changed since it left the factory.
254

To program the vehicle to a different mode, use
the following procedure:
1. Enter the personalization portion of the
SETUP menu following the instructions
listed previously.
2. Turn the TUNE/SEL knob until DOORS
UNLOCK KEY OUT/OFF is highlighted.
3. Press the TUNE/SEL knob to switch between
on and off.
When the mode is turned on, a check mark
will appear next to the feature name.
If this feature is selected, Doors Unlock in Park
(automatic transmission), Driver Unlock in
Park (automatic transmission), or Driver Unlock
Key Out/Off cannot be selected.
The mode you selected is now set. You can either
exit the programming mode by following the
instructions later in this section or program the
next feature available on your vehicle.
Delayed Locking
This feature delays the locking of the vehicle’s
doors for up to ve seconds after a power door lock
switch or the lock button on the Remote Keyless
Entry (RKE) transmitter is pressed. The ve second
delay occurs after the last door is closed.Programmable Modes
Mode 1:ON
Mode 2:OFF
Before your vehicle was shipped from the factory,
it was programmed to Mode 1. The mode to
which the vehicle was programmed may have
been changed since it left the factory.
To program the vehicle to a different mode, use
the following procedure:
1. Enter the personalization portion of the
SETUP menu following the instructions
listed previously.
2. Turn the TUNE/SEL knob until DELAYED
LOCKING is highlighted.
3. Press the TUNE/SEL knob to switch back and
forth between on and off.
When the mode is turned on, a check mark
will appear next to the feature name.
The mode you selected is now set. You can either
exit the programming mode by following the
instructions later in this section or program the
next feature available on your vehicle.
255

Notice:Before adding any sound equipment to
your vehicle, such as an audio system, CD
player, CB radio, mobile telephone, or two-way
radio, make sure that it can be added by
checking with your dealer/retailer. Also, check
federal rules covering mobile radio and
telephone units. If sound equipment can be
added, it is very important to do it properly.
Added sound equipment can interfere with the
operation of your vehicle’s engine, radio, or
other systems, and even damage them. Your
vehicle’s systems can interfere with the
operation of sound equipment that has
been added.
Your vehicle has a feature called Retained
Accessory Power (RAP). With RAP, the audio
system can be played even after the ignition
is turned off. SeeRetained Accessory Power
(RAP) on page 119for more information.Setting the Time
1. Press the TUNE/SEL (select) knob to enter
the main menu.
2. Turn the TUNE/SEL knob until SET CLOCK
appears on the display.
3. Press the TUNE/SEL knob to select
SET CLOCK.
4. Turn the TUNE/SEL knob to adjust the time.
5. Press the TUNE/SEL knob to update the
time. VEHICLE TIME UPDATED will appear
on the display.
If the CLOCK/RADIO DISP (display) is congured
into one of the congurable keys, pressing the key
will switch the display between the radio station
frequency and the time. See “Congurable Radio
Display Keys” underRadio with CD on page 260for
more information on conguring the keys.
259

XM™ Satellite Radio Service
XM™ is a satellite radio service that is based in
the 48 contiguous United States and Canada.
XM™ offers a large variety of coast-to-coast
channels including music, news, sports, talk,
traffic/weather (U.S. subscribers), and children’s
programming. XM™ provides digital quality
audio and text information that includes song title
and artist name. A service fee is required in
order to receive the XM™ service. For more
information, contact XM™; In the U.S. at
www.xmradio.com or call 1-800-852-XMXM (9696)
or in Canada at www.xmradio.ca or call
1-877-GET-XMSR (438-9677).
CLOCK/INFO DISP (Clock/Information Display):
Press the CLOCK/INFO DISP button to switch
between the clock display, the XM™ screen, and
the XM™ information display.Press this button while in XM™ mode to retrieve
three different categories of information related
to the current song or channel: Artist, Song Title,
and Category. To view this information, perform
the following:
1. Press the TUNE/SEL knob to enter the
main menu.
2. Turn the TUNE/SEL knob until CLOCK/INFO
DISP appears on the display.
3. Press the TUNE/SEL knob to select
CLOCK/INFO DISP. The display changes to
show the additional XM™ information.
4. To return to the original display, press the
CLR (clear) button or wait for the display to
time out.
If the CLOCK/INFO DISP is congured into one of
the congurable keys, pressing the key switches
the display between the radio station frequency
and the time. See “Congurable Radio Display
Keys” later in this section for more information.
261

QSCANR:Press the SCAN button to enter
scan mode. SCAN appears on the display.
Press the up arrow to scan to the next station.
The radio goes to a station, plays for ve seconds,
then goes to the next station. Press this button
again to stop scanning.
To scan preset stations, press and hold SCAN for
more than two seconds until you hear a beep
and PSCAN appears on the display. The radio
goes to the rst preset station stored on your rm
keys, plays for ve seconds, then goes to the
next preset station. Press SCAN again to
stop scanning presets.
The radio only scans stations with a strong signal
that are in the selected band.
LOCAL/DISTANT Selection:With this feature you
can set the radio to search for local stations or
stations that are further away for a larger selection.To set this feature to LOCAL or DISTANT, perform
the following steps:
1. Press the TUNE/SEL knob to enter the
main menu.
2. Turn the TUNE/SEL knob until SEEK LOCAL
or SEEK DISTANT appears on the display.
3. Press the TUNE/SEL knob to select either
LOCAL or DISTANT.
4. Press the CLR button to exit the display.
To return to the original display, repeatedly
press the CLR button or wait for the display to
time out.
To search for stations, press the SEEK up or down
arrows. If the system is set to LOCAL, SEEK
appears in the display and seeks to stations with
strong signals only. If the system is set to
DISTANT, D-SEEK appears in the display and
seeks to stations with weak and strong signals.
263

Setting Preset Stations
Up to 30 stations (six FM1, six FM2, and six AM,
six XM1 and six XM2 (if equipped)), can be
programmed on the six numbered rm keys, by
performing the following steps:
1. Turn the radio on.
2. Press BAND to select FM1, FM2, or AM, or
XM1 or XM2.
3. Tune in the desired station.
4. Press and hold one of the six numbered rm
keys for two seconds until you hear a beep.
The set preset station number appears on the
display above the rm key that it is set to.
Whenever that numbered rm key is pressed
for less than two seconds, the station that
was set returns.
5. Repeat the steps for each rm key.
To set the preset stations with an equalization
setting, DSP (digital signal processing)
setting, or a program type (PTY) setting, see
each of these features later in this section.
When a preset station is selected, once one of
these additional settings is selected, the
preset station remembers each setting and it
remains active, until the setting is selected
off for that preset station.AUTOSTORE PRESETS:To set the preset
stations automatically, perform the following steps:
1. Turn the radio on.
2. Press BAND to select FM1, FM2, or AM.
3. Press the TUNE/SEL knob to enter the
main menu.
4. Turn the TUNE/SEL knob until AUTOSTORE
PRESETS appears on the display.
5. Press the TUNE/SEL knob to select.
AUTOSTORE appears on the display.
The radio automatically searches the band
and selects and stores the six radio stations
with the strongest signal. The stations are
stored by signal strength, not sequential order.
The set preset station number appears on
the display above the rm key that it is set to.
Whenever that numbered rm key is
pressed for less than two seconds, the station
that was set returns.
6. Press the CLR button to exit the display.
To return to the original display, repeatedly
press the CLR button or wait for the display to
time out.
When battery power is removed and later applied,
you do not have to reset your radio presets.
264

PRESETS HOME/AWAY:This feature gives you
the ability to store two different kinds of station
presets. HOME can be used for stations available
where you live and AWAY can be for stations
available outside of your local broadcasting area.
To set preset stations for home and away
perform the following steps:
1. Press the TUNE/SEL knob to enter the
main menu.
2. Turn the TUNE/SEL knob until PRESETS
HOME/AWAY appears on the display.
3. Press the TUNE/SEL knob to select. HOME
or AWAY appears on the display.
4. Press the CLR button to exit the display. To
return to the original display, repeatedly press
the CLR button or wait for the display to
time out.
Follow the manual or automatic steps previously
listed for setting the preset rm keys for both home
and away.Setting the Tone (Bass/Treble)
To adjust the bass, midrange, and treble, perform
the following steps:
1. Press the TUNE/SEL knob to enter the
main menu.
2. Turn the TUNE/SEL knob until
BASS-MID-TREBLE appears on the display.
3. Press the TUNE/SEL knob to enter the tone
settings.
4. Press the TUNE/SEL knob to scroll through
the settings.
5. Turn the TUNE/SEL knob to increase or to
decrease the bass, midrange, or treble. If a
station is weak or noisy, decrease the treble.
6. Press the TUNE/SEL knob to set the
adjustment.
7. Press the CLR button to exit the display.
To return to the original display repeatedly
press the CLR button or wait for the display to
time out.
265