display CADILLAC ELDORADO 2002 10.G User Guide

2-65 Speedometer and Odometer
The speedometer lets you see your speed in both
miles per hour (mph) and kilometers per hour (km/h).
The odometer shows how far your vehicle has been
driven, in either miles (used in the United States) or
kilometers (used in Canada).
You may wonder what happens if a vehicle has to have
a new odometer installed. The new one may read the
correct mileage. This is because your vehicle's computer
has stored the mileage in memory.
Trip Odometer
This button is located in
the center of the instrument
panel to the right of the
steering wheel and below
the air outlets.By pressing this button, you can tell how far you've
traveled since you last set the trip odometer back
to zero.
For information on resetting this button,
see ªDIC Controls and Displaysº in the Index.
English/Metric Display
Press the SKIP INFO button until ENGLISH/METRIC
RESET displays and then press NO INFO RESET
to select.
Other readings such as temperature, fuel and trip
odometer also go back and forth between English
and metric.
Vehicle Speed Limiter
This feature prevents your vehicle from exceeding
speeds that the tires are not rated for. When this
happens, the engine's fuel supply is shut off. When the
vehicle speed slows, the fuel supply will come on again.

2-77 Security Light
This light works with
the PASS
-Key II system.
See ªPASS
-Key IIº in the
Index for more information.
Fuel Gage
The fuel gage shows
approximately how much
fuel is in the tank. It works
only when the ignition is
in RUN.Here are a few concerns some owners have had about
the fuel gage. All of these situations are normal and do
not indicate that anything is wrong with the fuel gage.

At the gas station the gas pump shuts off before
the gage reads full.

It takes more (or less) gas to fill the tank than the
gage said. For example, the gage read half a tank,
but it took more (or less) than the tank's remaining
capacity to fill it.

The gage may change when you turn, stop or
speed up.
Fuel Data Display
Everything you need to know about the fuel
economy and how far you can travel with your
vehicle's remaining fuel is displayed on the Driver
Information Center (DIC). Fuel data can be
obtained by pressing the SKIP INFO button
located on the instrument panel above the audio
system. See ªDIC Controls and Displaysº later
in this section for more information.

2-78
Driver Information Center (DIC)
This display gives you the status of many of your
vehicle's systems. The DIC is also used to display driver
personalization features and warning/status messages.
DIC Controls and Displays
YES TRIP RESET: By using this button, you can tell
how far you've gone since you last set the YES TRIP
RESET back to zero. To reset, press and hold this button
until zeros appear. If your vehicle is domestic, the trip
odometer will return to zero after 999.9 miles (1 609 km).
If your vehicle is Canadian, the trip odometer will return
to zero after 1 999.9 km (1,242 miles).NO INFO RESET: Pressing this button will reset the
MPG AVG, GAL FUEL USED, AVG MPH, TIMER,
OIL LIFE LEFT and ENGLISH/METRIC RESET.
Pressing NO INFO RESET when a non
-resettable
display appears will cause a ªrecallº mode to occur.
When this happens, all Driver Information Center (DIC)
warning messages that have been displayed since the
ignition key was turned to RUN will redisplay. If no
messages were displayed, a MONITORED SYSTEMS
OK message will appear.
SKIP INFO: Pressing this button repeatedly will
display the RANGE, MPG AVG, MPG INST, GAL
FUEL USED, AVG MPH, TIMER, BATTERY VOLTS,
OIL LIFE LEFT and ENGLISH/METRIC RESET.

MPG AVG (Reset): Press the SKIP INFO button
to display the MPG AVG (Average Fuel Economy),
then press and hold the NO INFO RESET button
until 0.0 MPG AVG is displayed.

GAL FUEL USED (Reset): Press the SKIP INFO
button to display the GAL FUEL USED on the
Driver Information Center (DIC), then press and
hold the NO INFO RESET button until 0.0 GAL
FUEL USED is displayed.

2-79

AVG MPH (Reset): Press the SKIP INFO button to
display the AVG MPH (Average Speed), then press
and hold the NO INFO RESET button until 0.0 AVG
MPH is displayed.

TIMER: This feature is like a stopwatch in that
you can clock the time it takes to get from one point
to another.
To operate, press the SKIP INFO button to display
TIMER. Each of the fields for the hours, minutes and
seconds are two numeric digits.
Once TIMER OFF 00:00:00 is displayed, press the
NO INFO RESET button to toggle between ON and
OFF. Once the TIMER is in OFF, press and hold
NO INFO RESET to reset the timer. If you will be
starting and stopping your vehicle
-- during a trip
for instance
-- the TIMER feature will automatically
start timing where it left off when you last stopped.
To reset it, press and hold the NO INFO RESET
button until the display reads TIMER 00:00:00.
Press the SKIP INFO button to exit from the
TIMER function.
ENGLISH/METRIC (Reset): Press the SKIP INFO
button to display ENGLISH/METRIC RESET,
then press the NO INFO RESET button to select.
The display will change from English (miles) to
metric (kilometers).

OIL LIFE LEFT (Reset): Press the SKIP INFO
button to display the OIL LIFE LEFT, then press and
hold the NO INFO RESET button until 100% OIL
LIFE LEFT is displayed. (This only needs to be reset
after you have had the oil changed.)
FUEL DOOR: Press this button to open the fuel
door. (This feature will work only when the shift lever is
in PARK (P) and the VALET lockout feature is turned
off, regardless of whether or not the vehicle is running.)
TRUNK: Press this button to open the trunk.
(This feature will work only when the shift lever is
in PARK (P) and the VALET lockout feature is
turned off, regardless of whether or not the vehicle
is running.)

2-80 DIC Messages
These messages will appear if there is a problem sensed
in one of your vehicle's systems. Vehicles that are first
sold in Canada will have a number after each message.
This number helps to identify the message which is
only displayed in English.
Pressing the INFO or NO INFO RESET button(s)
will remove most of the following messages from the
DIC display:
APPLY BRAKE TO SHIFT
- 46: This message
will appear if your vehicle is in PARK (P) for about
15 seconds and the brake is not pressed. On the climate
control panel, press the OFF button (next to the MODE
button) and the down arrow on the PASS TEMP button
for about five seconds. Hold the same two buttons to
display the message again.
BATTERY NOT CHARGING
- 7: This message will
appear if the battery is not being charged. Have the
electrical system checked by your dealership at your
earliest convenience.BATTERY VOLTAGE HIGH
- 8: This message
shows that the electrical charging system is
overcharging (more than 16 volts). To avoid being
stranded, have the electrical system checked by your
dealership. You can reduce the charging overload by
using the accessories. Turn on the lamps and radio, set
the climate control on AUTO and the fan speed on HI,
and turn the rear window defogger on. You can monitor
battery voltage on the DIC by pressing the SKIP INFO
button. The normal range is 11.5 to 15.5 volts when the
engine is running.
BATTERY VOLTAGE LOW
- 6: This message
will appear when the electrical system is charging
less than 10 volts or if the battery has been drained.
If this message appears immediately after starting,
it is possible that the generator can still recharge the
battery. The battery should recharge and may take a
few hours to do so. Consider using an auxiliary charger
to boost the battery after returning home or to a final
destination. (Be sure to follow the manufacturer's
instructions when using a battery charger.)

2-81
If this message appears and stays on while driving or
after starting your vehicle, have it checked immediately
to determine the cause of this problem. To help the
generator recharge the battery quickly, you can reduce
the load on the electrical system by turning off the
accessories. You can monitor battery voltage on the
DIC by pressing the SKIP INFO button. The normal
range is 11.5 to 15.5 volts.
CHANGE ENGINE OIL
- 82: This means that
the life of the engine oil has expired and it should be
changed within 200 miles (322 km). See ªEngine Oilº
in the Index. After an oil change, the Oil Life Indicator
must be reset. See ªOil Life Indicator, How to Resetº
in the Index.
CHANGE TRANS FLUID
- 47: This message will
appear when it is time to replace the transaxle fluid.
See ªMaintenance Scheduleº in the Index for the proper
fluid and change intervals.CHECK BRAKE FLUID LEVEL
- 37: This message
will display if the ignition is in RUN to inform the
driver that the brake fluid level is low. Have the brake
system serviced by a technician as soon as possible.
See ªBrake System Warning Lightº in the Index.
CHECK COOLANT LEVEL
- 2: This message
will appear when there is a low level of engine coolant.
Have the cooling system serviced by a technician as
soon as possible.
CHECK FUEL GAUGE
- 39: This message will
appear when the fuel supply is less than 3.5 gallons
(13.2 L) remaining. A single chime will also sound
when this message is displayed.
CHECK GAS CAP
- 61: This message will appear
if the gas cap has not been fully tightened. You should
recheck your gas cap to ensure that it's fully tightened.

2-82
CHECK OIL LEVEL - 36: For correct operation
of the low oil sensing system, your vehicle should be on
a level surface. A false CHECK OIL LEVEL message
may appear if the vehicle is parked on grades. The oil
level sensing system does not check for actual oil level
if the engine has been off for a short period of time, and
the oil level is never sensed while the engine is running.
If the CHECK OIL LEVEL message appears and
your vehicle has been parked on level ground with the
engine off for at least 30 minutes, the oil level should
be checked by observing the oil dipstick. Prior to
checking the oil level, be sure the engine has been off
for five minutes and your vehicle is on a level surface.
Then check the dipstick and add oil if necessary.
See ªEngine Oilº in the Index.
CHECK WASHER FLUID
- 25: This message
will appear for several seconds indicating that you
need windshield washer solvent.
CRUISE ENGAGED
- 43: This message will
appear for a few seconds when you select a speed at
which to cruise.DOOR AJAR
- 141: A door other than the driver's is
open or ajar when this message appears. The vehicle's
engine must be running and the transaxle not in
PARK (P) for this message to display. A chime will
also sound when the vehicle's speed is greater than
5 mph (8 km/h).
DRIVER DOOR AJAR
- 140: This message will
display when the vehicle is being shifted out of
PARK (P) with the engine running to signal that the
driver's door is open or ajar. A chime will also sound
when the vehicle's speed is greater than 5 mph (8 km/h).
ENGINE COOLANT HOT, IDLE ENGINE
- 44:
This message will appear when the engine coolant
temperature is over 248
F (126
C). To avoid added
strain on a hot engine, turn off the climate control
system. Stop and allow your vehicle to idle until it cools
down or the message is removed. If it does not cool
down, turn off the engine and have it serviced before
driving it again. Severe engine damage can result from
an overheated engine. See ªEngine Overheatingº in
the Index.

2-83
ENGINE HOT - A/C OFF - 16: This message
displays when the engine coolant becomes hotter than
the normal operating temperature. To avoid added strain
on a hot engine, the air conditioning compressor is
automatically turned off so that air conditioned air is
not delivered. If the coolant temperature returns to
normal, you must select AC to return to a normal A/C
compressor operation. If this message continues to
appear, have the system repaired as soon as possible to
avoid compressor damage.
ENGINE MISFIRE
-- EASE OFF GAS
PEDAL
- 114: An engine misfire has occurred.
You'll need to ease off the gas pedal.
ENGINE OVERHEATED, STOP ENGINE
- 42:
This message will appear when the engine has overheated.
Stop and turn the engine off immediately to avoid severe
engine damage. See ªEngine Overheatingº in the Index.
A multiple chime will also sound when this message
is displayed.
ENGINE POWER REDUCED
- 41: This message
informs you that your vehicle is reducing engine power
because the transaxle is being placed in gear under
conditions that may cause damage to the vehicle
powertrain or vehicle acceleration.FUEL LEVEL LOW
- 11 : This message serves as
a warning that the fuel level in the tank is critically low.
Stop for fuel soon.
HEADLAMPS SUGGESTED
- 23: If it's dark enough
outside and Twilight Sentinel is off, a HEADLAMPS
SUGGESTED message will display on the DIC.
This message informs the driver that turning on the
exterior lamps is recommended even though the
Daytime Running Lamps (DRL) are still illuminated
(it's become dark enough outside to require the
headlamps and/or other exterior lamps).
ICE POSSIBLE
- 13: This message appears when
the outside air temperature is cold enough to create icy
road conditions.
LOW REFRIG A/C OFF
- 12: This message means
that the air conditioning system detects a refrigerant
level that is low enough to cause damage to the air
conditioning compressor. Have the air conditioning
system serviced if this message appears.
MONITORED SYSTEMS OK
- 1: This message only
appears in the ªrecallº mode by pressing the NO INFO
RESET button. It lets you know that no other messages
are stored or are currently active.

2-84
OIL PRESSURE LOW STOP ENGINE - 35: If this
message appears while the engine is running, stop the
engine and do not operate it until the cause of low oil
pressure is corrected. Severe damage to the engine can
result. A multiple chime will also sound when this
message is displayed.
OPTIONS NOT SET
- 99: This message will display
if a fault has occurred in your vehicle's memory.
Have your vehicle serviced by your dealership.
PROGRAM PASS KEY
- 31: This warning message
displays when the PASS
-Key
II pellet information
has not been programmed into your vehicle. See your
dealership for service.
REMOVE KEY
- 70: This message will appear when
the PASS
-Key
II system is unable to read the pellet
on the ignition key or an improper key pellet has been
inserted. This message usually appears following the
display of STARTING DISABLED REMOVE KEY.
The instrument panel cluster will then run a timer and
change the messages to WAIT 3 MINUTES, WAIT
2 MINUTES, WAIT 1 MINUTE and then START CAR.
When the REMOVE KEY message is displayed, remove
the ignition key. Check the ignition key for damage. If it is damaged, it may need to be replaced. If you see
no damage, clean the pellet contacts with a soft cloth or
napkin before inserting the key back into the ignition.
Have your vehicle serviced if the message still appears.
SERVICE A/C SYSTEM
- 14: This message
appears when the electronic sensors that control the air
conditioning and heating systems are no longer working.
Have the climate control system serviced if you notice a
drop in heating and air conditioning efficiency.
SERVICE AIR BAG
- 83: There is a problem with
the Supplemental Inflatable Restraint (air bag) system
when this message appears. Let only a qualified
technician work on your vehicle. See your dealership
for service at once.
SERVICE BRAKE FLUID SWITCH
- 37: A problem
in the brake fluid detection circuit causes this message
to display if the ignition is in RUN. Have the brake
system serviced by a technician as soon as possible.
If the brake warning light is on, refer to the directions
listed in that part.

2-85
SERVICE CHARGING SYSTEM - 102: This
message will display when a problem with the charging
system has been detected. Have your vehicle serviced at
your dealership.
SERVICE ELECTRIC SYS
- 106: This message will
display if an electrical problem has occurred within the
Powertrain Control Module (PCM). Have your vehicle
serviced by your dealership.
SERVICE FUEL SYSTEM
- 101: The PCM has
detected a problem within the fuel system when this
message appears. See your dealership for service.
SERVICE IDLE CONTROL
- 107: A problem with
the idle control has occurred when this message displays.
Drive your vehicle to the dealership for service.
SERVICE RIDE SYS
- 84: This message is displayed
to indicate that the suspension system is not operating
properly. To correct this problem, have your vehicle
serviced at your dealership.SERVICE STEERING SYS
- 127: This message
is displayed when a problem has been detected in the
magnetic variable speed assist steering system.
Service is required. A single chime will also sound
when this message is displayed.
SERVICE TRANSMISSION
- 100: If a problem
is detected with the transaxle, this message will appear.
Have your vehicle checked by your dealership.
SERVICE VEHICLE SOON
- 3: If a problem is
detected with the transaxle, this message will appear.
Have your vehicle checked by your dealership.
SERV STABILITY SYS
- 54: If you ever see the
SERV STABILITY SYS message, it means there
may be a problem with your stability enhancement
system. If you see this message, try to reset the system
(stop, turn off the engine, then start the engine again).
If the SERV STABILITY SYS message still comes on,
it means there is a problem. You should see your dealer
for service. Reduce your speed and drive accordingly.
A single chime will also sound when this message
is displayed.