CADILLAC SRX 2007 1.G Owners Manual

Windshield Washer
{CAUTION:
In freezing weather, do not use your
washer until the windshield is warmed.
Otherwise the washer uid can form ice
on the windshield, blocking your vision.
The windshield washer button is located at the
end of the windshield wiper lever.
K(Washer Fluid):Press this button to wash
the windshield. Washer uid will squirt onto
the windshield and the wipers will run for a few
cycles to clear the windshield. For more wash
cycles, press and hold the button.If your vehicle is low on washer uid, the WASHER
FLUID LOW ADD FLUID message will appear
on the Driver Information Center (DIC) display.
SeeDIC Warnings and Messages on page 220for
more information.
If the headlamps are on when you wash the
windshield, the headlamp washer will turn on, if
your vehicle has them. Both the windshield and the
headlamps will be washed. SeeHeadlamp
Washer on page 173.
171

Rear Window Wiper/Washer
{CAUTION:
In freezing weather, do not use your
washer until the windshield is warmed.
Otherwise the washer uid can form ice
on the windshield, blocking your vision.
The switch for the rear
washer/wiper is located
in the overhead
console.
Z(Rear Wiper):Press this side of the button to
turn the rear wiper on.
Y(Washer Fluid):Press this button to wash
and wipe the window.
The rear window washer uses the same uid
bottle as the windshield washer. However, the rear
window washer will run out of uid before the
windshield washer. If you can wash your
windshield but not your rear windows, check the
uid level.
5(Delay):Press this side of the button to turn
on delayed wiping.
To turn either the delay or rear wiper setting off,
press the opposite side of the button to turn it
to the off position. Pressing the button all the way
down on either side will activate a wiper setting.
172

Headlamp Washer
Your vehicle may have headlamp washers. The
headlamp washers clear debris from the headlamp
lenses.
The headlamp washers are located to the inside
of the headlamps.To wash the headlamps, press the washer button
located at the end of the windshield wiper lever.
Both the headlamps and the windshield will be
washed. After the rst wash, the headlamps will be
washed after the fth press of the windshield
washer button.
The headlamps must be on to be washed. If the
headlamps are off, only the windshield will be
washed when the washer button is pressed. If the
washer uid is low, the headlamp washers will
not work.
SeeWindshield Washer on page 171for additional
information.
173

Cruise Control
These controls are
located on the end of
the multifunction lever.
9(Off):Move to this position to turn the
system off.
R(On):Move to this position to turn on the
system.
+ (Resume/Accelerate):Move to this position to
make the vehicle resume a previously set
speed or to accelerate when cruise is already
active.
T(Set/Decrease):Press this button to set the
speed or to decrease the speed when cruise
is already active.With cruise control, a speed of about 25 mph
(40 km/h) or more can be maintained without
keeping your foot on the accelerator. This
can really help on long trips. Cruise control does
not work at speeds below about 25 mph (40 km/h).
If you apply your brakes, the cruise control will
shut off.
{CAUTION:
Cruise control can be dangerous where
you cannot drive safely at a steady speed.
So, do not use your cruise control on
winding roads or in heavy traffic.
Cruise control can be dangerous on
slippery roads. On such roads, fast
changes in tire traction can cause
excessive wheel slip, and you could lose
control. Do not use cruise control on
slippery roads.
174

If your vehicle is in cruise control when the
Traction Control System (TCS) begins to limit
wheel spin, the cruise control will automatically
disengage. SeeTraction Control System (TCS) on
page 281andStabiliTrak
®System on page 283.
When road conditions allow you to safely use
it again, you may turn the cruise control back on.
Setting Cruise Control
{CAUTION:
If you leave your cruise control on when
you are not using cruise, you might hit a
button and go into cruise when you do
not want to. You could be startled and
even lose control. Keep the cruise control
switch off until you want to use cruise
control.1. Move the cruise control switch to on.
2. Get up to the speed desired.
3. Press in the set button at the end of the lever
and release it.
4. Take your foot off the accelerator pedal.
This light on the
instrument panel cluster
will come on while
cruise control is on.
175

Resuming a Set Speed
Suppose you set the cruise control at a desired
speed and then you apply the brake. This, of
course, disengages the cruise control. But it does
not need to be reset.
Once you are going about 25 mph (40 km/h) or
more, you can move the cruise control switch
briey from on to resume/accelerate.
You will go right back up to your chosen speed
and stay there.
If you hold the switch at resume/accelerate the
vehicle will keep going faster until you release the
switch or apply the brake. Do not hold the
switch at resume/accelerate, unless you want the
vehicle to go faster.
Increasing Speed While Using Cruise
Control
There are two ways to go to a higher speed:
Use the accelerator pedal to get to the higher
speed. Press the set button at the end of the
lever, then release the button and the
accelerator pedal. You will now cruise at the
higher speed.
Move the cruise switch from on to resume/
accelerate. Hold it there until you get up to the
desired speed, and then release the switch. To
increase your speed in very small amounts,
move the switch briey to resume/accelerate.
Each time you do this, your vehicle will go
about 1 mph (1.6 km/h) faster.
If using the accelerator pedal and the set button at
end of the lever to increase cruise set speed,
your new set speed must be at least 5 mph higher
than current speed for this method to work. If it
is not 5 mph higher, switch cruise switch off, then
on, and then reset your speed using the set
button.
176

Reducing Speed While Using Cruise
Control
There are two ways to reduce your speed while
using cruise control:
Press in the button at the end of the lever until
you reach the lower speed desired, then
release it.
To slow down in very small amounts, briey
press the set button. Each time you do this,
you will go about 1 mph (1.6 km/h) slower.
Passing Another Vehicle While Using
Cruise Control
Use the accelerator pedal to increase your speed.
When you take your foot off the pedal, the
vehicle will slow down to the cruise control speed
you set earlier.
Using Cruise Control on Hills
How well the cruise control works on hills depends
upon the vehicle speed, load, and the steepness of
the hills. When going up steep hills, you might have
to step on the accelerator pedal to maintain the
vehicle’s speed. When going downhill, you might
have to brake to keep the vehicle’s speed down.
Applying the brake will turn off the cruise control. If
you need to apply the brake due to the grade of the
downhill slope, you might not want to attempt to use
your cruise control feature.
Ending Cruise Control
To end a cruise control session, step lightly on the
brake pedal.
Stepping on the brake pedal will end the current
cruise control session only. Move the cruise control
switch to off to turn off the system completely.
Erasing Speed Memory
When you turn off the cruise control or the ignition,
the cruise control set speed memory is erased.
177

Headlamps
The exterior lamp control is located in the middle
of the turn signal/multifunction lever.
O(Exterior Lamp Control):Turn the control
with this symbol on it to operate the exterior lamps.
The exterior lamp control has four positions:
O(On/Off):Turn the control to this position to
turn off all lamps except the Daytime Running
Lamps (DRL).
AUTO (Automatic):Turn the control to this
position to put the headlamps in automatic mode.
AUTO mode will turn the exterior lamps on
and off depending upon how much light is
available outside of the vehicle.
;(Parking Lamps):Turn the control to this
position to turn on the parking lamps together with
the following:
Sidemarker Lamps
Taillamps
License Plate Lamps
Instrument Panel Lights
5(Headlamps):Turn the control to this position
to turn on the headlamps, together with the
previously listed lamps and lights.
Wiper Activated Headlamps
This feature activates the headlamps and parking
lamps after the windshield wipers have been in
use for about six seconds. For this feature to work,
the exterior lamp control must be in AUTO.
When the exterior lamp control is off or in the
parking lamp position and the windshield wiper
control is in any position except off, the Headlamps
Suggested message will appear on the DIC
display. See “Headlamps Suggested Message”
underDIC Warnings and Messages on page 220
for more information.
When the ignition is turned to OFF, the
wiper-activated headlamps will immediately turn
off. They will also turn off if the windshield
wiper control is turned off.
178

Headlamps on Reminder
A warning chime will sound if the exterior lamp
control is left on in either the headlamp or parking
lamp position and the driver’s door is opened
with the ignition off. SeeLights On Reminder on
page 212for additional information.
Daytime Running Lamps (DRL)
Daytime Running Lamps (DRL) can make it easier
for others to see the front of your vehicle during
the day. DRL can be helpful in many different
driving conditions, but they can be especially
helpful in the short periods after dawn and before
sunset. Fully functional daytime running lamps
are required on all vehicles rst sold in Canada.The DRL system will make the turn signal lamps
come on when the following conditions are met:
It is daylight and the ignition is in the ON or
START position.
The exterior lamp control is in the off or AUTO
position and the headlamps are off.
The automatic transmission is not in PARK (P).
When DRL are on, only the front turn signal lamps
will be on. No other exterior lamps will be on.
The instrument panel cluster will not be lit
up either.
179

When the exterior lamp control is in AUTO and it is
dark enough outside, the DRL will turn off and the
low-beam headlamps will turn on. When it is bright
enough outside, the low-beam headlamps will go
off, and the DRL will turn back on. If you start the
vehicle in a dark garage, the automatic headlamp
system will come on immediately. Once you leave
the garage, it will take about one minute for the
automatic headlamp system to change to DRL if it
is light outside. During that delay, the instrument
panel cluster may not be as bright as usual. Make
sure the instrument panel brightness lever is in the
full bright position. SeeInstrument Panel Brightness
on page 181.
To drive the vehicle with the DRL off, turn the
exterior lamp control off. Then turn on the
fog lamps or parking lamps, and the DRL will turn
off. This will work regardless of gear position
and whether or not the parking brake is set.
As with any vehicle, you should turn on the regular
headlamp system when you need it.Light Sensor
The light sensor for the DRL and AUTO headlamp
feature is located on top of the instrument panel.
If you cover the sensor, it will prevent it from
sensing light, and the exterior lamps may come on
whenever the ignition is on.
180