lights CADILLAC STS 2007 1.G User Guide

Passenger Airbag Status Indicator............. 245
Charging System Light.............................. 247
Brake System Warning Light..................... 248
Anti-Lock Brake System Warning Light...... 249
Low Tire Pressure Warning Light.............. 249
Traction Control System (TCS)
Warning Light........................................ 250
Engine Coolant Temperature
Warning Light........................................ 251
Engine Coolant Temperature Gage............ 251
Malfunction Indicator Lamp........................ 252
Oil Pressure Light..................................... 255
Security Light............................................ 256
Fog Lamp Light......................................... 256
Lights On Reminder.................................. 256
Cruise Control Light.................................. 256
Highbeam On Light................................... 257
Fuel Gage................................................. 257Driver Information Center (DIC).................. 258
DIC Controls and Displays........................ 258
DIC Warnings and Messages.................... 264
Other Messages........................................ 279
Audio System(s)......................................... 280
Setting the Time........................................ 281
Radio with CD........................................... 282
Using an MP3........................................... 297
XM Radio Messages................................. 303
Navigation/Radio System........................... 305
Radio Personalization................................ 305
Theft-Deterrent Feature............................. 309
Audio Steering Wheel Controls.................. 310
Radio Reception........................................ 312
Care of Your CDs..................................... 313
Care of the CD Player.............................. 313
Diversity Antenna System.......................... 314
XM™ Satellite Radio Antenna System....... 314
Section 3 Instrument Panel
176

Approaching and Following a Vehicle
The vehicle ahead
symbol will only appear
on the HUD when a
vehicle ahead is
detected in your path.
If this symbol does not appear, or disappears
briey, Adaptive Cruise Control will not respond to
vehicles you may see ahead.
{CAUTION:
When the Adaptive Cruise Control radar is
blocked by snow, ice, or dirt, it may not
detect a vehicle ahead. Adaptive Cruise
Control may not have time to slow your
vehicle enough to avoid a collision.
CAUTION: (Continued)
CAUTION: (Continued)
Do not use Adaptive Cruise Control when
the radar is blocked by snow, ice, or dirt.
Keep your radar clean. See “Cleaning the
System” later in this section.
Adaptive Cruise Control will, automatically, slow
your vehicle down when approaching a slower
moving vehicle. It will then adjust your speed to
follow the vehicle in front at the selected follow
distance. Your speed will increase or decrease to
follow the vehicle in front of you but will not
exceed the set speed. It may apply limited braking,
if necessary. When braking is active, your brake
lights will come on. It may feel or sound different
than if you were applying the brakes yourself. This
is normal.
205

This is a momentary switch that springs back to the
AUTO position when released. An AUTOMATIC
LIGHTS ON message appears on the DIC when
automatic lights are enabled or an AUTOMATIC
LIGHTS OFF message appears on the DIC when
the automatic lights are disabled.
AUTO (Automatic):Turn the control to this
position to put the headlamps in automatic mode.
AUTO mode, turns the exterior lamps on and
off depending upon how much light is available
outside of the vehicle.
Due to the switch design, the automatic lights may
be disabled even if the control is in the AUTO
position.
To enable automatic lighting do any of the
following:
Turn the headlamp control from AUTO to off
and release the switch. It returns back to the
AUTO position by itself.
Turn the headlamp control from the parking
lamp position to AUTO.
Turn the headlamp control from the headlamp
position to AUTO.To disable automatic lighting do any of the
following:
Turn the headlamp control from AUTO to off
and release the switch. It returns back to the
AUTO position by itself.
Turn the headlamp control from AUTO to the
parking lamp position.
Turn the headlamp control from AUTO to the
headlamp position.
Disabling automatic lighting disables the automatic
headlamp operation, DRL, and IntelliBeam™
High-Beams (if the vehicle has them).
;(Parking Lamps):Turn the control to this
position to turn on the parking lamps together with
the following:
Sidemarker Lamps
Taillamps
License Plate Lamps
Instrument Panel Lights
5(Headlamps):Turn the control to this position
to turn on the headlamps, together with the
previously listed lamps and lights.
212

IntelliBeam™ Intelligent High-Beam
Headlamp Control System
If your vehicle has this feature, be sure to read
this entire section before using it.
IntelliBeam™ is an enhancement to the vehicle’s
headlamp system. Using a digital light sensor
located on the back of the rearview mirror,
this system turns the high-beam headlamps on
and off according to surrounding traffic conditions.
The IntelliBeam™ system turns the high-beam
headlamps on when it is dark enough, there is no
other traffic present, and the IntelliBeam™
system is enabled.
Turning On and Enabling IntelliBeam™
AUTO3(IntelliBeam™ On/Off):Press
and release the IntelliBeam™ button on the inside
rear view mirror. The IntelliBeam™ indicator on
the mirror turns on. Once the system has
been turned on, it remains on each time the
vehicle is started. Additionally, the IntelliBeam™
system must be enabled.
To enable the IntelliBeam™ System, turn the
exterior lamp control to AUTO, with the turn
signal/multifunction lever in its neutral position.The High-Beam On Light appears on the
instrument panel cluster when the high-beams are
on. SeeHighbeam On Light on page 257. Your
vehicle has variable intensity high-beams.
The high-beam indicator on the instrument panel
cluster comes on as soon as the high-beams
start to come on, and remains on until the
high-beams have completely turned off. All
vehicles that have IntelliBeam™, however, quickly
turn off the high-beams if the system detects
the sudden presence of vehicle lights ahead.
Driving with IntelliBeam™
IntelliBeam™ only activates the high-beams when
driving over 20 mph (32 km/h).
The high-beam headlamps remain on, under the
control of IntelliBeam™, until any of the following
situations occur:
The system detects an approaching vehicle’s
headlamps.
The system detects a preceding vehicle’s
taillamps.
The outside light is bright enough that
high-beam headlamps are not required.
213

The high-beam headlamps are manually
turned on or you use the ash-to-pass feature.
SeeHeadlamp High/Low-Beam Changer on
page 183andFlash-to-Pass on page 188.
When either of these conditions occur,
the IntelliBeam™ feature is temporarily
disabled until the high-beam stalk is returned
to the neutral position. If either of these
conditions occur and IntelliBeam™ already
has the high-beam headlamps on, the
IntelliBeam™ feature is disabled and the
IntelliBeam™ light in the mirror turns off.
The exterior lamp control is turned to any
setting except AUTO.
When this occurs, IntelliBeam™ is disabled
until the control is turned back to the
AUTO position and the AUTOMATIC LIGHTS
ON message displays on the DIC.
The IntelliBeam™ system is turned off at the
inside rearview mirror.
The vehicle’s speed drops below
15 mph (24 km/h).IntelliBeam™ may not turn off the high-beams if
the system cannot detect other vehicle’s lamps
because of any of the following:
The others vehicle’s lamp(s) are missing,
damaged, obstructed from view, or otherwise
undetected.
The other vehicle’s lamp(s) are covered with
dirt, snow and/or road spray.
The other vehicle’s lamp(s) cannot be detected
due to dense exhaust, smoke, fog, snow, road
spray, mist, or other airborne obstructions.
Your vehicle’s windshield is dirty, cracked, or
obstructed by something that blocks the view
of the IntelliBeam™ light sensor.
Your vehicle’s windshield is covered with ice,
dirt, haze, or other obstructions.
Your vehicle is loaded such that the front end
of the vehicle points upward, causing the
IntelliBeam™ sensor to aim high and
not detect headlamps and taillamps.
You are driving on winding or hilly roads.
You might need to manually disable or cancel the
high-beam headlamps by turning the low-beam
headlamps on, if any of the above conditions exist.
214

Headlamps on Reminder
A warning chime will sound if the exterior lamp
control is left on in either the headlamp or parking
lamp position and the driver’s door is opened
with the ignition off. SeeLights On Reminder on
page 256for additional information.
Daytime Running Lamps (DRL)
Daytime Running Lamps (DRL) can make it easier
for others to see the front of your vehicle during
the day. DRL can be helpful in many different
driving conditions, but they can be especially
helpful in the short periods after dawn and before
sunset. Fully functional daytime running lamps
are required on all vehicles rst sold in Canada.
The DRL system will make the turn signal lamps
come on when the following conditions are met:
It is still daylight and the ignition is on,
the automatic lights are enabled, and
the transmission is not in PARK (P).
When DRL are on, only your front turn signal
lamps will be on. No other exterior lamps will be
on when the DRL are being used. Your instrument
panel will not be lit.When the automatic lights are enabled and it is dark
enough outside, the DRL will turn off and the
low-beam headlamps will turn on. When it is bright
enough outside, the low-beam headlamps will go
off, and the DRL will turn back on. If you start your
vehicle in a dark garage, the automatic headlamp
system will come on immediately. Once you leave
the garage, it will take about one minute for the
automatic headlamp system to change to DRL if it
is light outside. During that delay, your instrument
panel cluster may not be as bright as usual. Make
sure your instrument panel brightness lever is in the
full bright position. SeeInstrument Panel Brightness
on page 220.
To operate your vehicle with the DRL off, turn the
exterior lamp control off and then do one of the
following:
Turn the exterior lamp control to the parking
lamp position.
Turn the exterior lamp control to the headlamp
position.
Turn the exterior lamp control from AUTO to
off and back to AUTO.
216

An AUTOMATIC LIGHTS OFF message will
appear on the DIC, showing that automatic lighting
has been disabled.
As with any vehicle, you should turn on the
regular headlamp system when you need it.
Light Sensor
The light sensor for the DRL is located on top of
the instrument panel. If you cover the sensor, it will
read dark, and the exterior lamps may come on
when you do not need them.
Fog Lamps
Use the fog lamps for better vision in foggy or
misty conditions.
The fog lamp controls are located on the turn
signal/multifunction lever.
-(Fog Lamps):The band with this symbol is
used to turn the fog lamps on and off.
The parking lamps must be on for the fog lamps
to work.
To turn the fog lamps on, turn the fog lamp band
on the lever up to the dot and release it. The
band will return to its original position.
To turn the fog lamps off, turn the fog lamp band
up to the dot and release it. The band will
return to its original position, and the fog lamps
will turn off. If the high-beam headlamps are turned
on, the fog lamps will also turn off. They will turn
back on again when you switch back to low-beam
headlamps.
Some localities have laws that require the
headlamps to be on along with the fog lamps.
217

Instrument Panel Brightness
This feature controls the
brightness of the
instrument panel lights.
Press in the center knob on the DIC control panel
until the knob pops out. Then turn the knob
clockwise to brighten the lights or counterclockwise
to dim them. If you turn the knob completely
clockwise, the interior lamps will turn on.
Entry Lighting
The entry lighting system turns on the reading and
dome lamps and the backlighting to the exterior
lamp control when a door is opened or if you
press the remote keyless entry transmitter
unlock button. If activated by the transmitter, the
lighting will remain active for about 25 seconds.
The entry lighting system uses the light sensor; it
must be dark outside in order for the lamps to
turn on. The lamps turn off about 25 seconds after
the last door is closed. They will dim to off if the
ignition is on, or immediately deactivate if the
power locks are activated.
Parade Dimming
This feature prohibits dimming of the instrument
panel displays and backlighting during daylight
hours when the key is in the ignition and the
headlamps are on. This feature operates with the
light sensor and is fully automatic. When the
light sensor reads darkness outside and the
parking lamps are active, the instrument panel
displays can be adjusted by turning the instrument
panel brightness knob. SeeInstrument Panel
Brightness on page 220for additional information.
Base Level Shown,
Uplevel Similar
220

The URPA display is
located inside the
vehicle, above the
rear window. It has
three color-coded lights
that can be seen
through the rearview
mirror or by turning
around.
How the System Works
URPA comes on automatically when the shift lever
is moved into REVERSE (R) and the vehicle
speed is less than 3 mph (5 km/h). When
the system turns on, the three lights on the display
will illuminate for one and a half seconds to let
you know that the system is working. If your
vehicle is moving in REVERSE (R) at a speed
greater than 3 mph (5 km/h), the red light will ash
to remind you that the system does not work at
a speed greater than 3 mph (5 km/h).If an object is detected at a REVERSE (R) speed
of less than 3 mph (5 km/h), one of the following
will occur:
Description English Metric
Amber light 5 ft 1.5 m
Amber/amber lights 40 in 1.0 m
Amber/amber/red lights &
continuous chime20 in 0.5 m
Amber/amber/red lights
ashing & continuous
chime1 ft 0.3 m
A chime will sound the rst time an object is
detected between 20 inches (0.5 m) and
5 feet (1.5 m) away.
URPA cannot detect objects that are above trunk
level. In order for the rear sensors to recognize
an object, it must be within detection range behind
the vehicle.
227

The right knob controls the air delivery to the rear
passengers. Turning the knob all the way to
the left will shut off airow to the rear passengers.
Operating with the rear air delivery off may
make the entire vehicle warm or cool less quickly.
It may also increase the air rush sound of the
front system.
9(Off):This is the off position.
Y(Vent):This mode directs all the rear
passenger airow to the outlets in the console.
This is the normal position for cool down
conditions.
\(Bi-Level):This mode directs airow to the
console outlets and the oor.
[(Floor):This mode directs all of the airow to
the oor. This is the normal position for warm
up conditions.The amount of airow to the rear passengers is
controlled automatically by the front climate control
system, regardless of optional equipment.
Airow to the rear system will be turned off when
defrost is selected on the front climate control
panel to direct air to clear the windshield.
Vehicles equipped with a rear climate control
panel, also, have heated rear seats. There are
two buttons, each with three indicator lights,
located between the two climate control knobs on
the rear climate control panel, to control the
rear heated seats. SeeHeated Seats on page 14
for additional information.
Be sure to keep the area under the front seats
clear of any objects so the air in your vehicle can
circulate effectively.
238