remove seats CHERY TIGGO 2009 Service Repair Manual

Downloaded from www.Manualslib.com manuals search engine 2. Remove the valve keeper (1), valve spring retainer(2) and valve spring (3).
3. Remove valves (4) from the cylinder head.
Inspection
Inspect the valves for the following:
• Clean all valves thoroughly and discard burned,
warped and cracked valves.
• Check valve seats and valve faces for damage.
• When reconditioning valves follow the specifications
outlined for both intake and exhaust valves.
CYLINDER HEAD UNIT REPAIR
VISM080041
BESM020066
02
02–71Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 2. Remove the valve keeper (1), valve spring retainer(2) and valve spring (3).
3. Remove valves (4) from the cylinder head.
Inspection
Inspect the valves for the following:
• Clean all valves thoroughly and discard burned,
warped and cracked valves.
• Check valve seats and valve faces for damage.
• When reconditioning valves follow the specifications
outlined for both intake and exhaust valves.
CYLINDER HEAD UNIT REPAIR
VISM080041
BESM020066
02
02–144Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 1. Using the special tool MD-998772 (1), compressthe valve springs.
2. Remove the valve keeper, valve spring retainer and valve spring.
3. Remove valves from the cylinder head.
Valves
• Clean all valves thoroughly and discard burned,
warped and cracked valves.
• Check valve seats and valve faces for damage.
• When reconditioning valves follow the specifications
outlined for both intake and exhaust valves.
• Measure valve deflection.
VALVE DEFLECTION LIMIT (DIAL GAUGE READING)
Intake Valve 0.02 mm
Exhaust Valve 0.04 mm
CYLINDER HEAD UNIT REPAIR
LTSM020092
BESM020066
02–248Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine •Install the new valve guide from the top of the cylinder head as shown in the illustration.
Intake valve guide length: 45.5 mm
Exhaust valve guide length: 50.5 mm
CAUTION:
The intake and exhaust valves are different
lengths, use care when replacing the valve
guides to install the correct valve guide.
•Install the valve guide to the specified height (1) of
14 mm.
• After installing the valve guide, insert the new valve and check for smooth movement.
Valve Seats
•Before machining the valve seat, check the clear-
ance between the valve guide and the valve stem.
If the clearance is excessive, repair the valve and
valve guide if necessary before machining the valve
seat.
• Repair the width and angle of the valve seat until
the valve seat meets specified values.
• After repairing the valve seat, use valve lapping
compound to lap the valves and seats in pairs.
Valve Seat Replacement
•Cut out a portion of the original valve seat and
remove the valve seat from the cylinder head.
• Select the replacement valve seat according to the
outer diameter of the enlarged valve seat.
REPLACEMENT VALVE SEAT SIZES
Intake valve seat Enlargement size 0.30 mm
34.435 - 34.455 mm
Enlargement size 0.60 mm 34.735 - 34.755 mm
Exhaust valve seat Enlargement size 0.30 mm
31.935 - 31.955 mm
Enlargement size 0.60 mm 32.235 - 32.255 mm
CYLINDER HEAD UNIT REPAIR
LTSM020106
LTSM020103
LTSM020104
02
02–251Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 7. If equipped with a manual transaxle, remove theclamp (1) and slide the clutch actuator hose off the
reservoir port.
8. Clean the area around where the master cylinder attaches to the power brake booster using a suitable brake cleaner such as Brake Parts Cleaner or an equivalent.
9. Disconnect the brake tubes (1) and remove the nuts (2) attaching the master cylinder to the power
brake booster.
(Tighten: Master cylinder mounting nuts to 23 N·m)
10. Slide the master cylinder straight out of the power brake booster.
11. Installation is in the reverse order of removal.
NOTE :
After installation, bleed the master cylinder or bleed the entire brake system as necessary.
Master Cylinder - RHD
Description
The master cylinder body is an anodized aluminum casting. It is located at the right side of the engine room. It has
a machined bore to accept the master cylinder pistons and also has threaded ports with seats for hydraulic brake
tube connections. The master cylinder has the brake fluid reservoir mounted on top of it and supplies brake fluid to
the master cylinder as required. On manual transaxle equipped vehicles, the brake fluid reservoir also feeds the
clutch hydraulic circuit. The reservoir is made of clear plastic and it houses the brake fluid level switch.
ON-VEHICLE SERVICE
BESM120007
LTSM120041
LTSM120005
12–12Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Front Seat
Removal & Installation
1. Move the seat to the furthest forward position andremove the protective cover from the seat guide
rail.
2. Remove the guide rail mounting bolts (1). (Tighten: Guide rail mounting bolts to 32 N·m)
SEATS
LTSM150065
LTSM150066
15–106Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 3. Move seat to the furthest rearward position andremove the protective cover from the guide rail.
4. Remove the guide rail mounting bolts (1).
5. Disconnect seat heating element electrical connec- tor and remove the front seat.
6. Installation is in the reverse order of removal.
Rear Seats
Removal & Installation
1. Open the back door.
2. Pull the seat release (1) upward to fold the rear seat.
SEATS
LTSM150067
LTSM150133
15
15–107Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Heated Seat Switch
Removal & Installation
1. Using a trim stick, carefully remove the switches (1) from the mounting bezel.
2. Disconnect the heated seat switch electrical connector.
3. Installation is in the reverse order of removal.
Heated Seat Element
Removal & Installation
1. Disconnect the negative battery cable.
2. Remove the appropriate seat cushion.
3. Disconnect the inoperative heated seat cushion electrical connector.
4. Remove the inoperative heating element from the seat.
5. Installation is in the reverse order of removal.
SEATS
LTSM150127
15
15–109Chery Automobile Co., Ltd.