stop start CHEVROLET C/K 2003 Owner's Manual

6-6 What Fuel to Use
In the United States, for best results use Number 2-D
diesel fuel year
-round (above and below freezing
conditions) as oil companies blend Number 2
-D fuel to
address climate differences. Number 1
-D diesel fuel
may be used in very cold temperatures (when it stays
below 0
F or
-18
C); however, it will produce a power
and fuel economy loss. Avoid the use of Number 1
-D
diesel fuel in warm or hot climates. It may result in
stalling, poor starting when the engine is hot and may
damage the fuel injection system.
At a minimum, the diesel fuel you use should meet
specifications ASTM D975
-00 (Grade Low Sulfur) in
the United States. In addition, the Engine Manufacturers
Association (EMA) has identified properties of an
improved diesel fuel for better engine performance and
durability. Diesel fuels corresponding to the EMA
Recommended Guideline on Premium Diesel Fuel
(FQP
-1A) could provide better starting, less noise and
better vehicle performance. If there are questions about
the fuel you are using, contact your fuel supplier.Diesel fuel may foam when you fill your tank. This can
cause the automatic pump nozzle to shut off, even
though your tank isn't full. If this happens, just wait for
the foaming to stop and then continue to fill your tank.
CAUTION:
Heat coming from the engine may cause the fuel
to expand and force the fuel out of your tank. If
something ignites the fuel, a fire could start and
people could be burned. To help avoid this, fill
your fuel tank only until the automatic nozzle
shuts off. Don't try to ªtop it off.º

6-10
To drain water, do the following:
1. Stop and park the vehicle in a safe place. Turn off
the engine and apply the parking brake.
2. Remove the fuel cap.
3. Place a fuel
-resistant container under the fuel filter.
The filter drain valve is located on the bottom of the
fuel filter. The fuel filter is located in the engine
compartment on the passenger's side of the vehicle,
or on the driver's side frame rail near the engine.
4. Open the drain valve by
turning two to three
turns. When fuel
empties from the valve,
all the water has been
drained. Close the valve
hand tight.5. Remove the fuel
-resistant container and properly
dispose of the contaminated fuel. To find out how to
properly dispose of contaminated diesel fuel, see
ªWhat to Do with Used Oilº in the ªEngine Oil
(Diesel Engines)º part, later in this section.
6. Install the fuel cap.
7. Start the engine and let it run for a few minutes.
If the engine stalls, the fuel system may need to be
primed. While draining the water from the fuel filter,
air may enter the fuel system. If air has entered the
fuel system the fuel system will need to be primed.
Refer to ªFuel Primingº later in this section.
If the water in fuel indicator comes on again after
driving a short distance or the engine runs rough or
stalls, a large amount of water has probably been
pumped into the fuel tank. The fuel tank should
be purged.
Fuel Priming
In order for the DURAMAX diesel engine fuel system
to work properly, the fuel lines must be full of fuel and
contain no air. If air gets into the fuel lines, it will be
necessary to prime the fuel lines to eliminate air before
operating the vehicle.

6-25
As in the chart shown previously, SAE 5W-30 is best for
your vehicle. However, you can use SAE 10W
-30 if it's
going to be 0
F (
-18
C) or above. These numbers on
an oil container show its viscosity, or thickness. Do not
use other viscosity oils, such as SAE 20W
-50.
NOTICE:
Use only engine oil with the American Petroleum
Institute Certified For Gasoline Engines
starburst symbol. Failure to use the
recommended oil can result in engine damage not
covered by your warranty.
GM Goodwrench
oil meets all the requirements for
your vehicle.
If you are in an area where the temperature falls
below
-20F (-29C), consider using either an
SAE 5W
-30 synthetic oil or an SAE 0W-30 oil. Both
will provide easier cold starting and better protection for
your engine at extremely low temperatures.
Engine Oil Additives
Don't add anything to your oil. The recommended oils
with the starburst symbol are all you will need for good
performance and engine protection.
When to Change Engine Oil
(GM Oil Life System)
Your vehicle has a computer system that lets you know
when to change the engine oil and filter. This is based on
engine revolutions and engine temperature, and not on
mileage. Based on driving conditions, the mileage at
which an oil change will be indicated can vary
considerably. For the oil life system to work properly,
you must reset the system every time the oil is changed.
When the system has calculated that oil life has been
diminished, it will indicate that an oil change is
necessary. A change oil light will come on. Change your
oil as soon as possible within the next two times you
stop for fuel. It is possible that, if you are driving under
the best conditions, the oil life system may not indicate
that an oil change is necessary for over a year. However,
your engine oil and filter must be changed at least once
a year and at this time the system must be reset. It is also
important to check your oil regularly and keep it at the
proper level.
If the system is ever reset accidentally, you must change
your oil at 3,000 miles (5 000 km) since your last oil
change. Remember to reset the oil life system whenever
the oil is changed.

6-78 Headlamp Wiring
The headlamp wiring is protected by a circuit breaker in
the light switch. An electrical overload will cause the
lights to go on and off, or in some cases to remain off.
If this happens, have your headlamp wiring checked
right away.
Windshield Wiper Fuses
The windshield wiper motor is protected by a circuit
breaker inside the motor and a circuit breaker or fuse in
the fuse block. If the motor overheats, the wipers will
stop until the motor cools. If the overload is caused by
an electrical problem, be sure to get it fixed.
Fusible Links
A fusible link is a short piece of wire several gauge sizes
smaller than the circuit it protects. It will melt in an
overload situation, opening the circuit.
Your starter and other circuits have these fusible links.
The size is printed on the insulation. If the insulation is
burned beyond recognition, consult your GM dealer for
the proper size. Replace a fusible link with one of the
same size and insulation type. Fusible link insulation is a
special purpose high
-temperature material.
The hydraulic brake booster motor feed circuit and
starter circuit are protected by a fusible link. Vehicles
with a diesel engine have a fusible link for the intake
heater feed circuit.