clock CHEVROLET CAMARO 1967 1.G Chassis User Guide

FRONT SUSPENSION 3-6

Fig.
8 - Caster and Camber Adjustments - Chevy

To adjust for caster and camber, loosen the upper sup-

port shaft to crossmember nuts, add or subtract shims as

required and retighten nuts.

NOTE:
Caster and camber can be adjusted in

one operation.

Caster and camber specifications will be found in the

last section of this book.

Chevrolet and Chevy II

The caster angle is adjusted by turning the two niits at

the front of the lower control arm strut rod (figs. 7 and

8).
Shortening this rod will increase caster. Lengthen-

ing will decrease caster.

Camber angle is adjusted by loosening the lower con-

trol arm pivot bolt and rotating the cam located on this

pivot. This eccentric cam action will move lower control

arm in or out, thereby varying camber.

Steering Axis Inclination Adjustment

"Camber" is the outward tilt of the wheel and "steering

axis inclination" is the inward tilt of the knuckle. Cam-

ber cannot be changed without changing steering axis

inclination. Correct specifications willbe found at the

end of this section. If, with the camber correctly ad-

justed, the steering axis inclination does not fall within

the specified limits the knuckle is bent and should be

replaced.

If a new knuckle is installed, caster, camber and toe-in

must be readjusted.

Toe-In Adjustment

Toe-in, the inward pointing of both front wheels, is

checked with the wheels in the straight ahead position. It

is the difference of the distance measured between the

extreme front and the distance measured between the ex-

treme rear of both front wheels. Correct toe-in specifi-

cations will be found at the end of this section.
NOTE:
Toe-in must be adjusted after caster

and camber adjustment.

A. If the equipment being used measures the toe-in of

each wheel individually:

1.
Set the steering gear on the high point, mark 12

o'clock position on the steering shaft and position

the steering wheel for straight ahead driving.

2.
Loosen the clamp bolt at each end of each tie rod

and adjust to the total toe-in as given in the speci-

fications at the end of this book.

B.
If a tram gauge is being used, proceed as follows:

1.
Set the front wheels in the straight ahead position.

2.
Loosen the clamp bolts on one tie rod and adjust

for the proper toe-in as given in the specifications

at the end of this book.

3.
Loosen the clamp bolts on the other tie rod. Turn

both rods the same amount and in the same direc-

tion to place the steering gear on its high point and

position the steering wheel in its straight ahead

position.

C.
After the adjustment has been made:

1.
a. Chevrolet—Position inner tie rod clamp bosses

forward to 90° down to avoid stabilizer link bolt

interference.

b.
Chevelle—Position the tie rod clamp bosses

down to 45?° forward to avoid interference.

c. Chevy II--Position the outer tie rod clamp

bosses forward and not more than 45° up or

down from horizontal to avoid interference.

Inner clamps forward and vertical.

d. Corvette--Position inner tie rod clamps with

bolt horizontal and down. Position outer clamps

with bolt vertical and to the rear.

e. Camaro—Position inner tie rod clamps with

open end of clamp and slot in line. Position

relative to ground unimportant. Position outer

clamps with bolt top and 30° either side of ver-

tical. Position relative to slot unimportant.

RIDING HEIGHT AND COIL SPRING SAG

The following check will quickly determine whether or

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-27

SHIM AND

SERVICE

12

14

Fig.
72—Rear Axle Cross-Section (Chevrolet, Camaro, Chevelle and Chevy II)

1.
Companion Flange

2.
Deflector

3. Pinion Oil Seal

4.
Pinion Front Bearing

5. Pinion Bearing Spacer

6. Differential Carrier

LUBRICANT
7. Differential Case

8. Shim

9. Gasket

10.
Differential Bearing

11.
"Clock

12. Pinion Shaft Lock Bolt
13.
Cover

14.
Pinion Shaft

15.
Ring Gear

16.
Side Gear

17.
Bearing Cap

18.
Axle Shaft
19.
Thrust Washer

20.
Differential Pinion

21.
Shim

22.
Pinion Rear Bearing

23.
Drive Pinion

MAINTENANCE AND ADJUSTMENTS

The lubricant level should be periodically checked and

maintained at level of filler plug with a warm axle. See

the lubrication section of this manual for lubricant

recommendations.

Lubricant Leaks

Lubricant leaks should be checked for at the pinion

flange oil seal, axle wheel bearing seals, lubricant-filler
plug, and carrier cover. Correction of these leaks con-

sists of replacing the defective seals or gaskets involved

as described in this section.

AXLE BOLTS AND WHEEL NUTS

From a safety standpoint, axle housing to rear spring

bolts,
wheel nuts and control arm attaching bolts should

be periodically inspected for secure installation.

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES 5-4

RF

3

^ FRONT OF

~ VEHICLE

LF

4
RR

CZZZIZ3

2

LR

1

Fig.
5—Correct Bleeding Sequence

4.
Install brake bleeder wrench, Tool J-21472 on bleed-

er valve at wheel cylinder and install one end of

bleeder hose on bleeder valve (fig. 7).

5.
Pour a sufficient amount of brake fluid into a trans-

parent container to insure that end of bleeder hose

will remain submerged during bleeding. Place the

loose end of bleeder hose into the container. Be

sure the hose end is submerged in the fluid.

6. Open wheel cylinder bleeder valve by turning Tool

J-21472 counterclockwise approximately 1/3 of a

turn and observe flow of fluid at end of bleeder

hose.

7.
Close bleeder valve tightly as soon as bubbles stop

and brake fluid flows in a solid stream from the

bleeder hose.

8. Remove brake bleeder wrench and bleeder hose

from wheel cylinder bleeder valve.

9. Repeat Steps 4 through 8 on the remaining wheel

Cylinders in the correct bleeding sequence (fig. 5).

10.
Disconnect bleeder equipment from brake bleeder

adapter cover J-22489.

NOJE: The main cylinder on certain passenger

car models is tilted upward. When removing

the bleeder adapter on these models, place a

clean dry cloth behind and below the cylinder

to absorb any fluid spillage as the cover is

removed. v
Fig.
7—Bleeding Brakes Using Brake Bleeder

Wrench Tool J-21472

11.
adapter J-22489. Wipe all area

fluid was spilled during adapter

Fig.
6—Brake Bleeder Adapter Tool J-22489—Installed
Remove bleeder

dry of fluid if

removal.

12.
Fill master cylinder reservoirs to within 1/4" of

reservoir rims as shown in Figure 8.

13.
Install main cylinder diaphragm and cover.

MANUAL BLEEDING

1.
Clean all dirt from top of main cylinder and remove

cylinder cover and rubber diaphragm.

2.
Fill main cylinder reservoirs.

3.
Install brake bleeder wrench, Tool J-21472 on bleed-

er valve at wheel cylinder and install one end of

bleeder hose on bleeder valve (fig. 7).

4.
Pour a sufficient amount of brake fluid into a trans-

parent container to insure that end of bleeder hose

will remain submerged during bleeding. Place the

loose end of bleeder hose into the container. Be

sure the hose end is submerged in the fluid.

NOTE: Carefully monitor fluid level at main

cylinder during manual bleeding operations. Do

not bleed enough fluid at one time to drain the

reservoir completely. Replenish the reservoirs

with fluid while bleeding to insure a sufficient

amount of fluid is in the main cylinder at all

times.
To insure that outside air is not sucked

back into the hydraulic system, the bleeder

valve should be closed before the brake pedal

reaches the floor.

5.
Open wheel cylinder bleeder valve by turning Tool

J-21472 counterclockwise approximately 1/3 of a

turn. Slowly depress brake pedal. Just before brake

pedal reaches the end of its travel, close bleeder

valve and allow brake pedal to return slowly to the

fully released position. Repeat this procedure until

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES 5-22

2.
Replace ail push rods and pull back springs.

3.
Connect hose or line to wheel cylinder.

NOTE:
If replacing front wheel cylinder, con-

nect hose and inspect installation as outlined in

"Hydraulic Brake Hose Replacement".

4.
Install drum and wheel.

5. Bleed brakes as outlined in this section.

ANCHOR PIN

Front Wheel

1.
Raise front of vehicle and place on jack stands.

2.
Remove wheel and drum as outlined in this section.

3.
Remove brake shoe pull back springs, link and guide

plate.

4.
Disengage anchor pin lock and remove anchor pin by

turning counterclockwise.

5. Place new lock plate on anchor pin and pass pin

through the hole in flange plate and screw into tapped

hole in spindle support.

6. Torque pin to 130 lb. ft. and lock by peening over

washer tabs.

7. Install brake shoe guide plate, link and pull back

springs.

8. Adjust brakes, install drum and wheel as outlined

in this section. Test brake operation.

Rear Wheel

Two type anchor pins are used in production for the

rear wheels. The riveted type is not serviced and if

failure or damage should occur to either the anchor

pin or flange plate, both parts will have to be replaced

and the threaded type anchor pin used.

Threaded Type

1.
Raise rear of vehicle and place on jack stands,

2.
Remove wheel and drum as outlined in this section.

3.
Remove brake shoe pull back springs, link and guide

plate.

4.
Remove anchor pin retaining nut and washer and

remove pin from flange plate.

5. Position anchor pin to flange plate, install lock

washer and nut, and torque pin to 80 lb. ft.

6. Install brake shoe guide plate, link and pull back

springs.

7. Adjust brakes and install drum and wheel as outlined

in this section.

8. Test brake operation.

BRAKE DRUMS

Front brake drums are the demountable type; that is,

they can be removed without removing the hub. Rear

brake drums are demountable and may be removed

wihtout removing the axle shaft.

A lanced "knock out" area (fig. 34) is provided in

the web of the brake drum for servicing purposes in

the event retracting of the brake shoes is required in

order to remove the drum.

A small screw driver or hooked wire may be inserted

to disengage the automatic adjuster actuating lever so

the star wheel may be turned.

Removal

1.
Raise vehicle and place on jack stand.
2.
Remove wheel and tire assembly, back off brake

adjustment and remove drum.

Inspection and Reconditioning

Whenever brake drums are removed they should be

thoroughly cleaned and inspected for cracks, scores,

deep grooves, and out-of-round. Any of these conditions

must be corrected since they can impair the efficiency

of brake operation and also can cause premature failure

of other parts.

Smooth up any slight scores by polishing with fine

emery cloth. Heavy or extensive scoring will cause

excessive brake lining wear and it will probably be

necessary to rebore in order to true up the braking

surface.

An out-of-round drum makes accurate brake shoe

adjustment impossible and is likely to cause excessive

wear of other parts of brake mechanism due to its

eccentric action.

A drum that is more than .008" out-of-round on the

diameter is unfit for service and should be rebored.

Out-of^round, as well as taper and wear can be ac-

curately measured with an inside micrometer fitted

with proper extension rods.

If drum is to be rebored for use with standard size

brake facings which are worn very little, only enough

metal should be removed to obtain a true smooth braking

surface.

If drum has to be rebored more than .020" over the

standard diameter, it should be rebored to .060" diameter

oversize and the brake facing should be replaced with

.030"
oversize facings.

A brake drum must not be rebored more than .060"

over the maximum standard diameter, since removal

of more metal will effect, dissipation of heat and may

cause distortion of drum. Chevrolet brake facing is

not furnished larger than .030" oversize and this will

not work efficiently in drums bored more than .060"

oversize.

Brake drums may be refinished either by turning or

grinding. Best brake performance is obtained by turning

drums with a very fine feed. To insure maximum lining

life,
the refinished braking surface must be smooth and

free from chatter or tool marks, and run-out must not

exceed .005" total indicator reading.

Cleaning

New brake drums in parts stock are given a light.

coating of rust proofing oil to prevent the formation of

rust on the critical braking surfaces during the time

that the drums are in storage.

This rust proofing oil must be carefully removed

before the drum is placed in service to prevent any

of this oil from getting on the brake shoe facings, which

might cause an extreme brake grab condition.

It is recommended that a suitable volatile, non-toxic,

greaseless type solvent be used to clean the oil from the

braking surface of the new brake drums before they are

•placed in service to insure the cleanest possible surface.

Gasoline or kerosene should not be used as there is

danger that a portion of the diluated oil substance may

be left on the braking surface that may later cause

difficulty.

Installation

1.
Make brake adjustment as outlined in this section.

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE
6-3

(ROUND) Y~~fll^H

CENTRIFUGAL
A ^k

ADVANCE--jflgKpl

MECHANISM
UB|

CAM
KSK^2

LUBRICATOR
VlSMi

REPLACEMENT
^BK

-^ADJUST
SQUARELY

AND
JUST

TOUCHING
LOBE

OF
CAM
/ROTOR

HBB
__

I^BH^F
?
(SOUARE)

^K^ I /—
CAM

jKft^J / LUBRICATOR

H^T^
CAUTION!

QV NEVER
OIL

•L-^
CAM LUBRICATOR-

REPLACE
WICK

WHEN
NECESSARY
LATERAL

MISALIGNMENT
PROPER

LATERAL ALIGNMENT

Fig.
4- Distributor (V8)

CAUTION: Use extreme care
-when
using tap to

prevent cross threading. Also crank engine sev-

eral times to blow out any material dislodged

during cleaning operation.

7. Install spark plugs with new gaskets and torque to

specifications.

NOTE:
The following are some of the

greatest causes of unsatisfactory spark plug

performance.

•
Installation of plugs with insufficient torque to

fully seat the gasket.

•
Installation of the plugs using excessive torque

which changes gap settings.

•
Installation of plugs on dirty gasket seal.

•
Installation of plugs into corroded spark plug hole

threads.

8^ Connect spark plug wiring.

Service
Ignition System

1.
Remove distributor cap, clean cap and inspect for

cracks, carbon tracks and burned or corroded ter-

minals. Replace cap where necessary.

2.
Clean rotor and inspect for damage or deterioration.

Replace rotor where necessary.

3.
Replace brittle, oil soaked or damaged spark plug

wires.
Install all wires to proper spark plug. Proper

positioning of spark plug wires in supports is impor-

tant to prevent cross-firing.

4.
Tighten all ignition system connections.

5. Replace or repair any wires that are frayed, loose or

damaged.
Us
CORRECT
LATERAL MISALIGNMENT BY

j BENDING
FIXED CONTACT SUPPORT

[NEVER
BEND BREAKER LEVER

Fig.
5 - Point Alignment

Magnetic
Pulse(Breakerless)
Distributor

There are no moving parts in the ignition pulse ampli-

fier, and the distributor shaft and bushings have perma-

nent type lubrication, therefore no periodic maintenance

is required for the magnetic pulse ignition system. Refer

to Section 6Y for an analysis of problems and/or repair

procedures encountered on the Transistorized (Magnetic

Pulse) ignition system.

Standard
(Breaker Point) Distributor
(Figs.
3 or 4)

1.
Check the distributor centrifugal advance mechanism

by turning the distributor rotor in a clockwise direc-

tion as far as possible, then releasing the rotor to

see if the springs return it to its retarded position.

If the rotor does not return readily, the distributor

must be disassembled and the cause of the trouble

corrected.

2.
Check to see that the vacuum spark control operates

freely by turning the movable breaker plate counter-

clockwise to see if the spring returns to its retarded

position. Any stiffness in the operation of the spark

control will affect the ignition timing. Correct any

interference or binding condition noted.

3.
Examine distributor points and clean or replace if

riecessary.

DO
NOT SUCK

IN
TOO MUCH

ELECTROLYTE

TAKE
READING

AT
EYE LEVEL

Fig.
6 - Testing Specific Gravity of Battery

CHEVROtET
CHASSIS SERVICE MANUAL

ENGINE 6-7

Tune Up should be checked whenever the Air Injection

Reactor System seems to be malfunctioning. Particular

care should be taken in checking items that affect fuel-air

ratio such as the crankcase ventilation system, the car-

buretor and the carburetor air cleaner. Carburetors and

distributors for engines with the Air Injection Reactor

System are designed, particularly, for these engines;

therefore, they must not be interchanged with or replaced

by a carburetor or distributor designed for an engine

without the Air Injection Reactor System.

Choke Adjustment (Fig. 11)

With Remote Choke

1.
Remove air cleaner and check to see that choke

valve and rod move freely.

2.
Disconnect choke r*od at choke lever.

Check choke adjustment as follows:

On all except 275 hp 327 cu. in. engines, hold

choke valve closed and pull rod up against stop. The

top of choke rod end should be 1/2 - 1 rod diameter
4.

5.
above top of hole in choke valve lever.

On 275 hp 327 cu. in. engines, hold choke valve

closed and push rod down against stop on thermostat

bracket. The top of the choke rod should be 1/2 - 1

rod diameter below the top of the hole in the choke

lever.

If necessary, adjust rod length by bending rod at off-

set. (Bend must be such that rod enters choke lever

hole freely and squarely.)

Connect rod at choke lever and install air cleaner.

3.
With Manual
Choke

1.
Remove air cleaner.

2.
Push hand choke knob in to within 1/8" of instrument

panel.

3.
Loosen choke cable at carburetor bracket and adjust

cable through the clip until the choke valve is wide

open.

4.
Tighten cable clamp at carburetor bracket and check

operation of choke valve to ensure full closed and

wide open positions.

INSTRUMENT CHECK-OUT

Instrument Hook Up

Connect vacuum gauge, dwell meter, tachometer and

timing light as recommended by the manufacturer of the

equipment being used.

Check and Adjust Dwell

1.
Start engine then ch^ck ignition dwell.

.2.
If dwell is not within specifications, adjust dwell as

follows:

V8 ENGINES

• With engine running at idle, raise the adjustment

screw window-and insert an Allen wrench in the

socket of the adjusting screw (fig. 12).

• Turn the adjusting screw as required until a dwell

reading of 30° is obtained. A 2° variation is al-

lowable for wear.

• Close access cover fully to prevent the entry of

dirt into the distributor.

NOTE: If a dwell meter is not available, turn
adjusting screw clockwise until engine starts to

misfire, then turn screw one-half turn in the op-

posite direction to complete adjustment.

IN LINE ENGINES

• Remove distributor cap and recheck point setting.

If dwell is still not within specifications check the

distributor as outlined in Section 6Y.

Check Dwell Variation

Slowly accelerate engine to 1500 rpm and note dwell

reading. Return engine to idle and note dwell reading. If

dwell variation exceeds specifications, check for worn

distributor shaft, worn distributor shaft bushing or loose

breaker plate.

WINDOW

"HEX" TYPE

WRENCH

Fig.
12 - Setting Point Dwell (V8)
Fig.
13 - Ignition Timing Marks

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE 6-17

Fig.
5L
-
Engine Blocked for Pan Removal

NOTE: Do not install rocker arm cover.

11.
Start engine and allow warm up then retorque cylin-

der head
as
outlined in Step 4 and readjust valves as

outlined under Engine Tune Up.

OIL PAN

Removal

Chevrolet
and Camaro

1.
Disconnect battery positive cable.

2.
Remove through bolts from engine front mounts.

3.
Drain radiator, then disconnect upper and lower ra-

diator hoses at radiator.

4.
Remove fan blade as outlined in Section 6K.

5.
Raise vehicle then drain engine oil.

6. Disconnect and remove* starter.

7.
On
vehicles equipped with automatic transmission,

disconnect transmission cooler lines at transmission

and remove converter housing underpan.

8. Disconnect steering
rod at
idler lever then swing

steering linkage for oil pan clearance.

9. Rotate crankshaft until timing mark
on
torsional

damper is at 6:00 o'clock position.

10.
Using
a
suitable jack (and a block of wood to prevent

damaging oil pan), raise engine enough to insert 2"
x

4"
wood blocks under engine mounts (fig. 5L), then

lower engine onto blocks.

NOTE:
If
2"
x
4" wood blocks are cut 5-1/2"

long they can be used on all Chevrolet engines.

The 5-1/2" length up for in line engines and the

4"
side up for V8 engines.

11.
Remove oil pan and discard gaskets and seals.

Cfievel/e

1.
Remove enginfe from vehicle as outlined.

2.
Place engine on jack stands, one at each front mount

and one at transmission extension.

CAUTION: Leave engine lift attached
to
en-

gine.
Do not remove all weight
of
engine from

engine lift.

3.
On
vehicles equipped with automatic transmissions

remove converter housing underpan.

4.
Remove starter.

5.
Remove oil pan and discard gaskets and seals.
Chevy//

1.
Disconnect battery positive cable.

2.
Drain engine oil.

3.
Disconnect then remove starter.

4.
Disconnect-steering idler arm bracket at right hand

frame rail and swing steering linkage down for pan

clearance.

5.
On L6 engines, remove front crossmember.

NOTE:
On
station wagon
let
stabilizer
bar

hang while removing crossmember.
"

6. Remove oil pan and discard gaskets and seals.

Installation

1.
Thoroughly clean all gasket sealing surfaces.

NOTE: Use
a
new pan gasket set.

2.
Install rear seal in rear main bearing cap.

3.
Install front Seal on crankcase front cover pressing

tips into holes provided in cover.

4.
Install side gaskets on cylinder block (fig. 6L).

5.
Complete installation as follows:

Life

1
i

If ^
jfp^;.^3p
>\~^^ \s3^^r' -'••'•'-^^Hll

|^=-5p|:*iil^<iBBM||

mm

Fig.
6L
-
Pan Gaskets and Seals

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE 6-18

NOTE:
Bolts into crankcase cover should be

installed last. They are installed at an angle

and holes line up after rest of pan bolts are

snugged up.

Chevrolet and Camaro

a. If crankshaft was rotated while pan was off, place

timing mark at 6:00 o'clock position.

b.
Install oil pan and torque bolts to specifications.

c. Using a suitable jack (and a block of wood to prevent

damaging oil pan) raise engine enough to remove 2" x

4"
wood blocks, then lower engine.

d. On vehicles equipped with automatic transmission

install converter housing underpan, then connect

transmission cooler lines.

e. Install and connect starter.

f. Lower vehicle and install fan blades as outlined in

Section 6K.

g. Connect upper and lower radiator hoses.

h. Install through bolts in engine front mounts.

i. Connect battery positive cable.

j.
Fill radiator with coolant and fill engine with oil,

then start engine and check for leaks.

Chevelie

* a. Install oil pan and torque bolts to specifications.

b.
On vehicles equipped with automatic transmission,

install converter housing underpan.

c. Install starter.

d. Install engine as outlined.

Chevy II

a. Install oil pan and torque bolts to specifications.

Fig.
7L- Removing Oil Sea! (Lower Half)
Fig.
8L - Removing Oil Seal (Upper Half)

b.
On L6 engines, install front crossmember.

c. Connect steering idler arm.

d. Install starter and connect wires.

e. Connect battery cable, fill with oil, start engine and

check for leaks.

OIL PUMP

Removal

1.
Remove oil pan as outlined.

2.
Remove two flange mounting bolts, pickup pipe bolt,

then remove pump and screen as an assembly.

Installation

1.
Align oil pump drive shafts to match with distributor

tang, then install oil pump to block positioning flange

over distributor lower bushing. Use no gasket.

NOTE:
Oil pump should slide easily into place,

if not, remove and reposition slot to align with

distributor tang.

2.
Install oil pan using new gaskets and seals as

outlined.

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE 6-28

damper comes near the "0" mark on the front

cover.
11
the valves are not moving, the engine is

in the number 1 firing position. If the valves

move as the mark comes up to the timing tab, the

.
engine is in number 6 firing position and crank-

shaft should be rotated one more revolution to

reach the number 1 position,

b.
Valve adjustment is made by backing off the ad-

justing nut (rocker arm stud nut) until there is

play in the push rod and then tighten nut to just

remove all push rod to rocker arm clearance.

' this may be determined by rotating push rod with

fingers as the nut is tightened (fig. 4
V).
When

push rod does not readily move in relation to the

rocker arm, the clearance has been eliminated.

The adjusting nut should then be tightened an

additional 1 turn to place the hydraulic lifter

plunger in the center of its travel. No other

adjustment is required.

c. With the engine in the number 1 firing position

as determined above, the following valves may be

adjusted.

Exhaust - 1, 3, 4, 8

Intake - 1, 2, 5, 7

d. Crank the engine one revolution until the pointer

"(X" mark and torsional damper mark are again

in alignment. This is number 6 firing position.

With the engine in this position the following

valve may be adjusted.

Fig.
5V - Valve Adjustment (Mechanical)
Exhaust - 2, 5, 6, 7

Intake
-•
3, 4, 6, 8

With Mechanical Valve
Lifters

a. Crank engine until mark on torsional damper

lines up with center or "0" mark on the timing

tab and the engine is in the number 1 firing posi-

tion. This may be determined by placing fingers

on t£e number 1 cylinder valve as the mark on the

damper comes near the n0" mark on the front

cover. If the valves are not moving, the engine

is in the number 1 firing position. If the valves

move as the mark comes up to the timing tab, the

engine is in number 6 firing position and crank-

shaft should be rotated one more revolution to

reach the number 1 position.

b.
With the engine in the number 1 firing position as

determined above, adjust the following valves to

specifications with a feeler gauge (fig. 5V).

Exhaust - 4, 8

Intake - 2, 7. .

c. Turn crankshaft 1/2 revolution (180°) clockwise

and adjust the following valve to specifications

with a feeler gauge.

Exhaust -3,6

Intake - 1, 8

d. Turn crankshaft 1/2 revolution (180°) clockwise

until the pointer "0" mark and torsional-damper

mark are again in alignment. This is number 6

firing position. With the engine in this position,

adjust the following valves to specifications with

a feeler gauge.

Exhaust -5,7

Intake - 3, 4

e. Turn crankshaft 1/2 revolution (180°) clockwise

and adjust the following valves to specifications

with a feeler gauge.

Exhaust - 1, 2

Intake - 5, 6

f. Readjust valves (hot and running) as outlined

under "Engine Tune Up".

4.
Install rocker arm covers as outlined.

5.
Adjust carburetor idle speed and mixture.

VALVE LIFTERS

Hydraulic valve lifters very seldom require attention;

The lifters are extremely simple in design, readjust-

ments are not necessary, and servicing of the lifters re-

quires only that care and cleanliness be exercised in the

handling of parts.

Locating Noisy Lifters (Hydraulic)

Locate a noisy valve lifter by using a piece of garden

hose approximately four feet in length. Place one end of

the hose near the end of each intake and exhaust valve

with the other end of the hose to the ear. In this manner,

the sound is localized making it easy to determine which

lifter is at fault.

Another method is to place a finger on the face of the

valve spring retainer. If the lifter is not functioning

properly, a distinct shock will be felt when the valve re-

turns to its seat.-*

The general types of valve lifter noise are as follows:

1.
Hard Rapping Noise—Usually caused by the plunger

becoming tight in the bore of the lifter body to such

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE 6-30

c". Install the valve locks and release the compres-

sor tool making sure the locks seat properly in

the upper groove of the valve stem.

NOTE: Grease may be used to hold the locks

in place while releasing the compressor tool.

396 and 427
cu.
in.
Engines

a. Install new valve stem oil seal (coated with oil)

in position over valve guide.

b.
Set the valve spring and damper and valve cap in

place.

c. Compress the spring with Tool J-5892 and install

the valve locks, then release the compressor tool,

making sure the locks seat properly in the groove

of the valve stem.

NOTE: Grease may be used to hold the locks

in place while releasing the compressor tool.

7.
Install spark ,plug, using a new gasket, and torque to

specifications. -

8. Install and adjust valve mechanism as outlined.

CYLINDER HEAD ASSEMBLY

Removal

1.
Remove intake manifold as outlined.

2.
Remove exhaust manifolds as outlined.

3.
Remove valve mechanism as outlined.

4.
Drain cooling system (block).

5.
Remove cylinder head bolts, cylinder head and gas-

ket. Place cylinder head on two blocks of wood to

prevent damage.

Installation

CAUTION: The gasket surfaces on both the

head and the block must be clean of any foreign

ttter and free of nicks or heavy scratches.

Under bolt threads in the block and threads on

Pie cylinder head bolt must be cleaned. (Dirt

will affect bolt torqueT)

1.
On engines using a STEEL gasket, coat both sides of

a new gasket with a good sealer, spread the sealer

thin and even. One method of applying the sealer that

will assure the proper- coat is with the use of a paint

roller. Too much sealer may hold the beads of the

gasket away from the head or block.

CAUTION: Use no sealer on engines using a

composition STEEL ASBESTOS gasket.

2.
Place the gasket in position over the dowel pins with

the bead up.

3.
Carefully guide cylinder head into place over dowel

pins and gasket.

4.
Coat threads of cylinder head bolts with sealing

compound and install finger tight.

5.
Tighten cylinder head bolts a little at a time in the

sequence shown on the torque sequence chart until

the specified torque is reached.

6. Install the exhaust manifold as outlined.

7.
Install the intake manifold as outlined.

8. Install and adjust the valve mechanism as outlined.
OIL
PAN

Removal

Chevrolet
and Camaro

1.
Disconnect battery positive cable.

2.
Disconnect distributor cap from distributor (to pr-e-

vent breaking distributor cap when engine is raised).

3.
Drain radiator, then disconnect lower radiator hose

at water pump and remove oil dip stick and tube

(where necessary). '

4.
Remove fan blade.

5.
Raise vehicle then drain engine oil;

6. Remove through bolts from engine front mounts.

Disconnect and remove starter.

7.
On vehicles equipped with automatic transmissions,

remove converter housing underpan.

8. Disconnect steering rod at idler lever then swing

steering linkage 4pwn for oil pan clearance.

9. Rotate crankshaft untii timing mark on torsional

damper is at 6:00 o'clock position.

10.
Using a suitable jack, and a block of wood to prevent

damaging oil pan, raise engine "enough to insert 2" x

4"
wood blocks under engine mounts (fig. 8V), then

lower engine onto blocks.

NOTE: If 2" x 4" wood blocks are cut 5-1/2"

long they can be used on all Chevrolet engines.

The 5-1/2" length up for In-line engines and the

4"
side up for V8 engines.

11.
Remove oil pan and discard gaskets and seals.

NOTE: -On the 396 and 427 cu. in. engine, the

oil pan has three 1/4" x 20 attaching bolts at ,

crankcase front cover. One located at each

corner and one at lower center.

Chevelle

1.
Remove engine from vehicle as outlined.

2.
Lower engine onto jack stands, one at each front

Tnaount and one at transmission extension.

CAUTION: Leave engine lift attached to en-

gine.
Do not remove all weight of engine off

engine lifET

3.
Remove starter.

4.
On vehicles equipped with automatic transmission

remove converter housing underpan.

5.
Remove oil pan and discard gaskets and seals.

Fig.
8V - Engine Blocked for Pan Removal

CHEVROLET CHASSIS SERVICE MANUAL