key CHEVROLET CAMARO 1967 1.G Chassis Owner's Manual

STEERING 9-31

Fig.
63—Freeing Ball Stud

rod threads with EP Chassis lube and install ends on

tie rod making sure both ends are threaded ah equal

distance from the tie rod.

2.
Make sure that threads on ball stud and in ball stud

nuts are perfectly clean and smooth. Install neoprene

seals on ball studs.

NOTE: If threads are not clean and smooth,

ball studs may turn in tie rod ends when at-

tempting to tighten nut.

3.
Install ball studs in steering arms and relay rod.

4.
Install ball stud nut, and install cotter pins. Lubri-

cate tie rod ends.

5.
Adjust toe-in as described in Section 3.

NOTE: Before locking clamp bolts on the rods,

make sure that the tie rod ends are in alignment

with their ball studs (each ball joint is in the

center of its travel). If the tie rod is not in

alignment with the studs, binding will result.

RELAY ROD-ALL MODELS EXCEPT CORVETTE

Removal

1.
Remove inner ends of tie rods from relay rod as

described under Tie Rod - Removal.

2.
Remove cotter pin and nut from relay rod ball stud

attachment at pitman arm.

3.
Detach relay rod from pitman arm. Shift steering

linkage as required to free pitman arm from relay

rod.

4.
Remove cotter pin and nut from idler arm and re-

move relay rod from idler arm.

Installation

1.
Install relay rod to idler arm, making certain idler

stud seal is in place, then install and tighten nut.

Advance nut just enough to align castellation with

cotter pin hole and install pin.

2.
Raise end of rod and install on pitman arm. Secure

with nut and cotter pin.
3.
Install tie rod ends to relay rod as previously

described under Tie Rods. Lubricate tie rod ends.

4.
Adjust toe-in (see Section 3) and align steering wheel

as described previously in this section under Steer-

ing Wheel Alignment and High Point Centering.

RELAY ROD-CORVETTE

Removal

1.
Remove steering damper from relay rod as outlined

under Steering Damper-Removal. Remove anchor

bracket from relay rod by disconnecting two mount-

ing bolts.

2.
Remove inner ends of tie rods from relay rod as

described under Tie Rod--Removal.

3.
Remove cotter pin from end of relay rod at pitman

arm ball stud attachment, and remove stud nut.

4.
Tap brJl stud out of pitman arm and lower relay rod.

5.
Remove cotter key and nut from idler arm and re-

move relay rod from idler arm. Remove washer and

seal from idler arm.

Installation

1.
Place relay rod on idler arm stud, making certain

idler stud seal and washer are in place, then install

and tighten nut. Advance nut just enough to align

castellation with cotter pin hole and install pin.

2.
Install new seal and clamp over ball at end of pitman

arm.

3.
Install inner spring seat and spring to relay rod.

4.
Raise end of rod and install on pitman arm.

5.
Install spring seat, spring, and end plug.

6. Tighten end plug until springs are compressed and

plug bottoms, then back off 3/4 turn plug amount

necessary to insert cotter pin. Insert cotter pin to

lock adjustment.

7.
Install tie rod ends to relay rod as previously de-

scribed under Tie Rods.

8. Lubricate tie rod ends and pitman arm to relay rod

ball joint.

9. Install steering damper bracket and tighten bolts.

Install damper as outlined under Steering Damper--

Installation.

10.
Adjust toe-in and align steering wheel as described

previously in this section.

IDLER ARM

Chevrolet, Chevelle, Comoro, and Corvette (Fig. 62)

Removal

1.
Remove idler arm to frame nut, washer, and bolt.

No washer is used on Corvette.

2.
Remove cotter pin and nut from idler arm to relay

rod ball stud.

3.
Remove relay rod from idler arm by tapping relay

rod with a hammer using a heavy hammer as a

backing.

4.
Remove idler arm.

Installation

1.
On Chevrolet, place seal in position on idler arm

stud; position stud up through frame, and secure with

lock washer and nut.

2.
On Chevelle, Camaro, and Corvette, position idler

CHEVROLET CHASSIS SERVICE MANUAL

STEERING
9-32

arm on frame and install mounting bolts, washers

and nuts. No washer is used on Corvette.

Install relay rod to idler arm, ^making certain seal

is on stud. Install and tighten nut.

Install cotter pin.

Refer to torque specifications at rear of manual for'

correct torque values.

Chevy II (Fig. 62}

Removal

1.
Remove cotter pin, nut and washer securing idler

arm to relay rod.

2.
Remove relay rod from idler arm.

3.
If equipped with power steering disconnect power

cylinder shaft from idler arm bracket.

4.
Remove three idler bracket to frame bolts and nuts

and remove bracket and idler arm assembly.

5.
Remove cotter pin, nut, washer and bolt securing the

idler arm to the bracket.

6. Press out the idler arm bushing for replacement.

Installation

NOTE: Installation must be done with front

wheels straight ahead or the car will lead to one

side.

1.
Install idler arm bushing, if previously removed.

NOTE: Make certain the outer sleeve of the

bushing does not protrude above surface of idler

arm.

2.
Reverse removal procedure and torque all nuts ac-

cording to specifications.

PITMAN ARM

Removal

1.
Remove cotter pin from pitman arm ball stud and

remove nut.

2.
Remove relay rod from pitman arm by tapping on

side of rod or arm in which the stud mounts with a

hammer while using a heavy hammer or similar tool

as a backing. Pull down on relay rod to remove

from stud.

3.
Remove pitman arm nut from sector shaft and mark

relation of arm position to shaft.

4.
Remove pitman arm with Tool J-6632 as shown in

Figure 2.

Installation

1.
Install pitman arm on sector shaft, lining up the

• marks made upon removal.

2.
Install sector shaft nut.

3.
Position relay rod on to pitman arm. Install nut.

Continue to tighten arm enough to align castellation

with hole in stud and install cotter pin.
STEERING ARM

If, through collision or other damage, it becomes nec-

essary to remove and replace either steering arm, pro-

ceed as follows:

Removal

1.
Remove tie rod from steering arm as outlined in this

section.

2.
Remove front wheel, hub and brake drum as a unit

by removing hub cap and dust cap, cotter pin from

spindle nut and the spindle nut. Pull assembly to-

ward outside of vehicle. If removal is difficult, it

may be necessary to back off brake adjustment to

increase brake shoe-to-drum clearance; see Hy-

draulic Brake Adjustment, Section 5. On models

with disc brakes, remove caliper and disc.

3.
With wheel and drum assembly or caliper and disc

removed, steering arm retaining bolt heads are ac-

cessible and removal of steering arm from vehicle

may be accomplished by removing retaining nuts.

Installation

1.
Place steering arm in position on vehicle and install

retaining bolts*

2.
Install nuts. Use only the special locknut listed for

this use in the Chevrolet Parts Catalog.

3.
Pack wheel bearings using a high quality wheel

bearing lubricant. Install bearings and wheel-hub-

brake drum assembly removed previously. On disc

brake models, install disc and caliper.

4.
Install keyed washer and spindle nut. Proceed as out-

lined under t{ Front Wheel Bearing Adjustment" in

Section 3.

5.
Install tie rod ball stud in steering arm. Be sure that

the dust cover is in place on ball stud.

6. Install castellated nut on ball stud, tighten securely

and install cotter pin.

7.
Following directions given in Section 3 to check cor-

nering wheel relationship and toe-in; correct as

required.

STEERING DAMPER-CORVETTE

Removal

1.
Remove bolt from damper pivot bracket at relay rod.

2.
Remove nut from damper pivot at frame bracket and

withdraw damper assembly.

Damper is serviced as a unit. Replace damper if
3.

damaged or excessively worn.

Installation

1.
Place piston rod end into frame bracket and install

retainers, bushings, and nut.

2.
Insert cylinder end pivot into relay rod bracket and

install through bolt.

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-43

23.
Install
MCtT
ring over steering shaft using snap ring

installer J-22659 (refer to Section 9).

NOTE: Be sure retaining ring is completely

seated into groove.

24.
Install dial pointer on Chevrolet and Chevelle models

equipped with automatic transmission (if applicable).

25.
Install dial indicator and lamp assembly on Camaro

and Chevy n models equipped with automatic

transmission.

26.
Install mast jacket lower trim covers (if applicable).

27.
Install hazard warning knob and turn signal lever.

28.
Install shift lever.

29.
Install steering wheel.

30.
Install multiple connector to switch wiring using old

harness for wire color guide and connect to body

harness connector.

31.
Connect battery ground cable and check operation of

assembly.

Tilt Steering Column (Fig. 57)

Chevrolet, Chevelle and Camaro

1.
Disconnect battery ground cable.

2.
Disconnect directional switch wiring harness from

body harness at multiple connector under instrument

panel.

3.
Remove steering wheel assembly (refer to Steering,

Section 9).

4.
Remove preload spring and cancelling cam from end

of shaft.

5.
Remove shift lever pin and lever from steering col-

umn (except floor shift).

6. Remove directional le*ver screw and lever.

7.
Push in hazard warning knob and unscrew knob.

8. On Camaro models equipped with automatic trans-

mission, remove quadrant dial and lamp assembly

from column.

9. Remove mast jacket trim cover
(s).

10.
On Chevrolet and Chevelle models with automatic

transmission, loosen set screw and remove quadrant

dial pointer.

11.
Assemble slide hammer Tool J-6585-1 to turn signal

cover remover Tool J-21486. Place cover remover

over turn signal cover, tighten clamp, and pull cover

from end of column with slide hammer (Refer to

Steering, Section 9).

12.
Remove three switch mounting screws, noting short

length of top screw.

13.
Cut multiple connector from switch wiring and slide

switch from end of column.

14.
To install new switch, feed wiring through the bear-

ing housing, around support, and through shift bowl

and shroud.

15.
Feed through wiring protector. If clearance is not

sufficient loosen mast jacket bracket retaining bolts.

16.
Insert switch wiring terminals in multiple connector.

Use old connector
and
wiring for color guide.
17.
Position switch and install three mounting screws

with short screw in top position.

18.
Be sure hazard warning switch is pushed in, then

install turn signal cover using special Tool J-21853.

On automatic columns align key in cover with keyway

in bearing housing.

19.
Install turn signal lever, hazard warning knob and

tilt lever.

20.
Install shift lever and roll pin (where applicable).

21.
Install dial pointer on Chevrolet and Chevelle. On

Camaro install dial indicator and lamp assembly.

22.
Install trim covers and retaining screws.

23.
Install cancelling cam and preload spring.

24.
Install steering wheel (Refer to Section 9).

25.
Connect switch wiring to body harness under instru-

ment panel.

26.
Connect battery ground cable and check operation of

unit.

Standard and Telescoping Steering Column

Corvette (Fig. 58)

1.
Disconnect battery ground cable.

2.
Disconnect signal switch harness wiring from chas-

sis wiring harness at multiple connector under in-

strument panel.

3.
Remove steering wheel assembly as outlined in

Steering, Section 9.

4.
Remove preload spring and cancelling cam.

5.
Remove directional signal lever screw and lever.

6. Push in hazard warning knob, unscrew and remove

knob.

7.
Remove lower trim cover retaining screws and

cover.

8. Remove retaining ring, thrust and wave washers

from upper end of shaft.

9. Cut wiring above connector.

10.
Remove three switch mounting screws, slide switch,

cover and upper bearing housing from column, pull-

ing wire through protector and escutcheon.

11.
To install replacement switch, assemble upper bear-

ing housing and turn signal switch into switch cover,

then feed wiring through escutcheon and protector

until switch can be positioned on mast jacket.

12.
With switch positioned on mast jacket, install three

switch mounting screws.

13.
Install thrust and wave washers and snap lock ring

in place.

14.
Install turn signal lever and hazard warning knob.

15.
Install cancelling cam and upper bearing preload

spring on steering shaft.

16.
Install steering wheel assembly.

NOTE:
Be sure directional signal switch is in

neutral position before installing wheel.

17.
Install connector on directional signal wiring har-

ness and connect to body harness connector.

CHEVROLET CHASSIS SERVICE