Brake lights CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual

ENGINE-ELECTRICAL 6Y-10

circuit. Make absolutely certain all connections in

the circuit are secure.

5.
Do not short across or ground any of the terminals

on the generator or regulator.

6. Do not attempt to polarize the generator.

7.
Do not disconnect lead at generator without first dis-

connecting battery ground cable.

Trouble in the A.C. charging system will usually be

indicated by one or more of the following conditions:

1.
Faulty indicator lamp or ammeter operation.

2.
An undercharged battery (usually evidenced by slow

cranking speeds).

3.
An overcharged battery (usually evidenced by exces-

sive battery water usage).

4.
Excessive generator noise or vibration.

Described below are a series of on-the-vehicle quick

checks which are designed to assist the service tech-

nician in locating troubles within the various components

of the engine electrical system. Additional checks, ad-

justments and overhaul procedures of these components

are also described in the "Charging Systems—Service

Operations Section" and should be referred to as

necessary.

STATIC CHECKS

Before making any electrical checks, perform the fol-

lowing static checks:

1.
Check for loose fan belt.

2.
Check for defective battery. (Refer to Battery).

3.
Inspect all connections, including the slip-on con-

nectors at the regulator and Delcotron.

NOTE: Do not short field to ground to check if

generator is charging since this will seriously

damage the charging system.

SYSTEM CONDITION TEST

This test is used .to indicate the overall condition of the

charging system (both good and defective) and to isolate

the malfunctioning unit if the system is defective.

NOTE: On Corvette models difficulty may be

encountered -when attempting to make the re-
quired test connections at the voltage regulator.

It is advisable to remove the regulator from its

mounting location to perform the necessary con-

nections at the regulator for the following tests

but make sure unit is grounded.

1.
With ignition off, perform the prescribed Static

Checks outlined in this section. Then set hand brake

and shift transmission
into
neutral.

2.
Connect a voltmeter from junction block relay to

ground at regulator base.

CAUTION: Be sure meter clip does not touch a

resistor or terminal extension under regulator,

3.
Connect a tachometer on engine.

4.
Models equipped with Indicator Lamp: Turn ignition

switch on "ON" position and check indicator lamp.

If lamp fails to glow, perform appropriate tests and

corrections (Indicator Lamp Circuit Tests) before

continuing.

Models equipped with Ammeter: Turn ignition

switch to "ACC" with an accessory on and check

ammeter. If ammeter fails to read discharge, check

ammeter circuit before continuing.

5.
Models equipped with Indicator Lamp: If lamp glows,

start the engine and run' it at 1500 rpm or above.

Check indicator lamp. If lamp fails to go out, per-

form appropriate test and corrections (Indicator

Lamp Circuit Test) before continuing.

Models equipped with Ammeter: If ammeter reads

discharge, start the engine and observe ammeter. If

meter fails to move toward charge (from original

position), perform appropriate test and corrections

(Field Circuit Tests) before continuing.

NOTE: At this point a field circuit has been

established and any other problem will lie in

generator or regulator.

6. Turn on high-beam headlights and heater blower

motor to high speed, run engine at or above 1500

rpm (for a few minutes, if necessary) and read the

voltage on meter.

AIR GAP

ADJUSTING NUT

ONLY

ADJUSTING SCREW

(Turn To Adjust

Voltage Setting)

Fig.
6c—Adjusting Voltage Setting

CHEVROLET CHASSIS SERVICE MANUAL

SECTION 12

ELECTRICAL-BODY AND CHASSIS

CONTENTS
OF
THIS
SECTION

Page
Page

System 12-1

Instruments and Gauges 12-21

Directional Signal 12r40
Windshield Wipers and Washers 12-44

Wiring Diagrams 12-56

Special Tools 12-60

LIGHTING SYSTEM

INDEX

Page

General Description
!2-i

Maintenance and Adjustments
•.................. 12-2

Headlamp Adjustment......................
12-3

Headlamp Panel Travel Adjustment.
12-5

Service Operations.
. . .. 12-5

Front Lighting
12-5

Headlamp
. 12_5

Parking Lamp
12-5

Fender Lamp
. 12_^

Headlamp Panel
12-8

Headlamp Panel Motor
^2-9

Rear Lighting
l2-10

Tail, Stop and Directional Lamps
12-10
Page

Backing Lamps
12-14

License Plate Lamp
12-14

Automatic Transmission Quadrant Lamp
12-14

Seat Separator Console Lamps
. 12-15

Lighting Switch
. . 12-15

Wiper Switch.
12-15

Stoplight Switch
12-15

Dimmer Switch
12-15

Backing Lamp Switches
12-15

Neutral Safety Switches
12-17

Parking Brake Alarm Switch
................. 12-19

Instrument Panel Compartment Lamp/Switch
12-19

Cirgarette Lighter
12-19

GENERAL DESCRIPTION

.
The lighting system includes: the main lighting switch,

stop light, dimmer, and backing lamp switches, head-

lamps, parking lamps, stop, tail and directional lamps,

instrument illumination and indicator lamps, and the

necessary wiring to complete the various circuits. A

fuse panel provides convenient power take offs and fuse

clips for the appropriate circuits (fig. 1).

Chevrolet and Chevelle headlamp installation is all

new in that the headlamps are located in the radiator

support with adjusting screws and springs. Eliminating

the need for having separate headlamp housings. Chev-

rolet and Chevelle headlamp retainers and springs are

interchangeable.

Chevy n headlamp housings are new because of revised

front end styling and Corvette front end lighting is basi-

cally carryover.

Front fender lamps have been added as an option for

Chevrolet models and as standard equipment on Caprice

series.

Camaro models use single headlamps and the Rally

Sport model headlamps are covered by a retractable

section of the grille when lamps are not used. The sec-

tion of the grille covering the headlamps folds back when

lights are required; the headlamps are stationary. The

covering is retracted by a small electric motor mounted

to the headlamp housing. The headlamps are automat-

ically uncovered when the headlight switch is pulled "ON"

for illumination. If at any time the electrical circuit

becomes inoperative, the lamps can be uncovered manu-

ally. The ignition switch must be
"ON"
in order to close

the headlamp doors.

Parking lamp for Chevelle and Chevrolet models are
new due to revised front end sheet metal and bumper

styling. Parking lamps are located in the bumper on

Chevrolet, Chevelle and Chevy n models

Camaro parking lamps are located in the radiator

grille except for the Rally Sport models on which the

parking lamps are in the valance panel. For styling

reasons, the lens is white and an amber glass bulb is

used. All Camaro parking lamps require a separate

ground wire to assure a good ground contact because of

the plastic grille and painted contact surfaces.

The Chevrolet tail, stop, and directional lamps are in

one housing with a three section lens design on Impala

and Caprice sedans. The center lens for Impala series

is the back-up lamp. The center lens on the Caprice is

a tail lamp with the back-up lamps being located in the

rear bumper. Chevrolet station wagons have three indi-

vidual housings with three lenses, the center lamp being

the back-up. Biscayne and Bel-Air sedans have a single

housing and lens for tail, stop, and directional lamp with

a similarly constructed back-up lamp inboard and adja-

cent to it.

Chevelle tail, stop, and directional lamps are a single

lens design that follows through with the rear fender

styling. The back-up lamp is located in r.ear bumper.

Camaro models except Rally Sport have tail lamps

with integral back-up lamps mounted inboard of the rear

fenders between the trunk opening and bumper. The

Rally Sport model has dual tail lamps in the rear housing

and valance mounted back-up lamps.

Corvette, Chevy n, and Corvair tail and directional

signal lights are carryover. The Corvette has new back-

up lamps center mounted above the license plate opening.

CHEVROLET CHASSIS SERVICE

ELECTRICAL-BODY AND CHASSIS 12-21

2.
Remove ash tray, retainer attaching screws and

retainer.

3.
Remove Air Conditioning distributor
duct'
retaining

screws and duct.

4.
Remove heater and/or Air Conditioning control panel

assembly retaining screws and push panel assembly

from console.

NOTE:
If interference between control panel

and radio is encountered, loosen radio retaining

nuts.

5. Remove radio control knobs, bezels and retaining

nuts.

6. Disconnect radio wiring harness and antenna lead-in.

7. Remove radio rear brace attaching screw and re-

move ra(Jio from vehicle.

8. Remove ignition switch bezel nut using Tool J-7607

and push switch rearward.

9. Disconnect cigarette wiring connector.

10.
Remove cigarette lighter retainer and lighter as-

sembly from console.

11.
To install, reverse removal procedure.
Fig.
35 - Cigarette Lighter — Chevelle

CHEVROLET INSTRUMENTS AND GAUGES

INDEX

Page

General Description 12-21

Service Operations 12-22

Instrument Cluster........................ 12-22

Instrument Cluster Lamps 12-22

Printed Circuit .
* •
12-22

Speedometer 12-22

Speedometer Cable 12-23

Fuel Gauge 12-23
Page

Clock 12-24

Tachometer 12-24

Ammeter . . 12-24

Temperature Gauge 12-24

Oil Pressure Gauge 12-24

Oil Pressure Indicator 12-24

Generator Indicator 12-26

Temperature Indicator 12-26

GENERAL DESCRIPTION

The standard instrument cluster on all models contains

seven circular housings consisting of: a speedometer;

fuel gauge; oil pressure, generator and temperature indi-

cators; right and left directional signal indicators; brake

warning and high beam indicators; and includes a clock

on deluxe models. An optionally available instrument

cluster provides special instrumentation which includes

in addition to the speedometer and clock: a tachometer;

fuel, oil pressure, ammeter and engine temperature

gauges; which replace the standard fuel gauge and indi-

cator lights. The brake warning indicator is relocated

to the tachometer dial face and the high beam and direc-

tional indicators are positioned in the speedometer dial

face.

Instrument cluster removal is recommended before at-

tempting to service the printed circuit and gauges even

though some units may be accessible from behind the

cluster. Limited working space under the instrument

panel increases the possibility of electrical malfunctions

due to poor connections, and damaged or improperly in-

stalled printed circuit. The printed circuit is service-

able but not repairable and requires complete
replacement.

The brake warning light serves a dual purpose. It

functions as an indicator when the parking brake is ap-

plied and also warns if a malfunction (loss of hydraulic

pressure) should occur in the brake system. The two

separate switches, which provide the signal to operate the

indicator, are located at the parking brake support and in

the hydraulic brake line at the master cylinder. Service

of the brake pressure, differential switch unit at the

master cylinder is described in Section 5 of this manual.

All indicator and cluster illumihating lamps may be

replaced without removing the cluster from the vehicle.

The bulbs are installed in plastic holders which lock into

the cluster housing and make contact with the printed

circuit. An instrument lamp is used to illuminate the

ignition switch. A special fibre optic lucite wiring

transmits light from the lamp to the switch.

Regular maintenance is not required on the instrument

cluster or its components other than maintaining clean,

tight electrical connections, replacing defective parts and

keeping the speedometer cable properly lubricated.

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY
AND
CHASSIS
12-26

•
Low oil
pressure

• High engine temperature

• Defective wiring
or
switch

connector from sender

in block above starter
on

and
at
left front
of
distributor
on V-8
Sending Unit Replacement

1.
Disconnect wiring harness

unit terminal (located

L-6 engines

engines).

2.
Remove sender unit using Tool J-21757
or 12
point

socket, replace with
new
unit
and
check operation.

GENERATOR INDICATOR

1.
Ignition
on,
Engine
not
Running
and
Telltale Light

Off.

• Indicator bulb burned out, replace bulb.

• Open circuit
or
loose connection
in the
telltale

light circuit.

2.
telltale Light Stays
on
after Engine
is
Started.
If indicator light does
not go out at
engine idle

speed, refer
to
Charging Systems under Engine

Electrical, Section
6Y.

TEMPERATURE (COOLING SYSTEM) INDICATOR

The temperature indicator circuit consists
of two re-

motely located units, indicator gauge
and
engine sender

unit.
The
indicator gauge, located
in the
instrument

panel, consists
of a
red light which will indicate
an
over-

heated engine condition.

Engine Sender Unit Replacement

1.
Drain engine cooling system
to a
level below unit.

2.
Remove sender unit (located
in the
inlet manifold

near water pump housing
on V-8
engines and
in the

cylinder head near
an
exhaust port
oh L-6
engines)

and replace with new unit.

3.
Refill cooling system
and
check operation
of
unit.

CHEVELLE INSTRUMENTS AND GAUGES

INDEX

Page

General Description
* *
i2-26

Service Operations
12-26

Instrument Panel
12-26

Instrument Cluster.
12-26

Fuel Gauge and/or Ammeter
12-27

Clock,
i 12-27

Speedometer
12-27
Page

Speedometer Cable
.
. 12-27

Temperature Gauge
12-29

Oil Pressure Gauge
12-29

Indicator Lights.
. 12-29

Oil Pressure Indicator
12-29

Generator Indicator
. . 12-29

• Temperature Indicator
12-29

GENERAL DESCRIPTION

The Chevelle instrument cluster assembly consists
of:

a speedometer;
a
fuel gauge;
a
generator,
an
engine
tem-

perature and an
oil
pressure indicator lamp, and includes

a clock
on
deluxe models.
On
super sport models,
am-

meter, coolant temperature
and oil
pressure gauges
re-

place
the
appropriate indicator lights. Except
for the

speedometer,
all of the
indicator lamps, instruments
and

gauges
of
these clusters may
be
serviced without remov-

ing
the
instrument cluster assembly from
the
vehicle.

In addition
to the
instrument indicator lamps,
a
brake

warning lamp
is
included
in the
cluster
as
standard

equipment.
The
indicator
is
connected
to the
parking
brake
and
brake pressure differential switches
and

serves
a
dual function.
It
lights when the parking brake

is applied
and
also when
the
brake pedal
is
applied,
if a

malfunction should occur
in the
brake system
due to a

loss
of
hydraulic pressure. Servicing
of the
hydraulic

pressure differential switch
is
covered
in
Section
5 of

this manual.

Regular maintenance
is not
required on the instrument

cjLuster
or its
components other than maintaining dean

and tight electrical connections, replacing defective parts

and keeping
the
speedometer cable properly lubricated.

SERVICE OPERATIONS

INSTRUMENT PANEL ASSEMBLY

INSTRUMENT CLUSTER (Figs.
41
thru
44)

Removal

1.
Disconnect battery ground cable.

2.
Remove steering coupling bolt and disconnect steer-

ing shaft from coupling.

3.
Loosen mast jacket lower clamp.

4.
Remove
air
conditioning center distributor duct
(if

so equipped).

5. Remove radio rear support bracket screw.

6. Remove mast jacket upper support clamp and retain-

ing bolts from lower support (refer
to
Section
9,

Steering).
CAUTION: Cover mast jacket
and
parl

brake handle with
a
suitable material
to
prevc

scratching.

7.
Disconnect speedometer cable
at
rear
of
cluster

housing
and
speed warning control knob
at
panel
(if

so equipped).

8. Remove instrument panel retaining screws (nine

upper and five lower).
.

9. Working under the console remove four lower retain-

ing screws from instrument cluster housing.

10.
Pull instrument panel assembly from console and
lay

forward on mast jacket.

11.
Disconnect wiring harness, cluster lamps and wiring

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY
AND
CHASSIS
12-31

CHEVY II INSTRUMENTS AND GAUGES

INDEX

Page
Page

General Description -.....
12-31

Service Operations.
12-31

Instrument Panel
. 12-31

Instrument Cluster
12-31

Fuel Gauge
12-32

12-32
Clock,
Speedometer
12-34

Speedometer Catte
12-34

Indicator Lights
12-34

Oil Pressure Indicator
12-34

Generator Indicator
12-34

Temperature Indicator
12-34

GENERAL DESCRIPTION

The Chevy
n
instrument cluster assembly consists
of:

a speedometer;
a
fuel gauge;
a
generator, temperature

and
oil
pressure indicator lamps, and includes
a
clock
on

deluxe models. Except
for the
speedometer,
all of the

cluster lamps, instruments and gauges
of
the cluster
may

be serviced without removing
the
instrument cluster
as-

sembly from
the
console.

In addition
to the
instrument indicator lamps,
a
brake

warning lamp
is
included
in the
cluster
as
standard

equipment.
The
indicator
is
connected
to
thfc parking

brake and brake pressure differential switches andserves
a dual function.
It
lights when
the
parking brake
is ap-

plied
and
also when
the
brake pedal
is
applied,
if a mal-

function should occur
in the
brake system
due to a
loss
of

hydraulic pressure. Servicing
of the
hydraulic pressure

differential switch
is
covered
in
Section
5 of
this manaul.

Regular maintenance
is not
required on
the
instrument

cluster
or its
components other than r^Mfitftl^i^g clean

and tight electrical connections, replacing defective parts

and keeping
the
speedometer cable properly lubricated.

SERVICE OPERATIONS

INSTRUMENT PANEL

INSTRUMENT CLUSTER

Removal
and
Installation {Figs.
45
thru
48)

1.
Disconnect battery ground cable.

2.
Remove mast jacket upper support clamp (refer
to

Steering, Section
9, for
complete procedure
on low-

ering jacket) and lower steering column.

NOTE:
Apply protective material
to the
mast

jacket
to
prevent damage
to the
painted surfaces.
3.
Disconnect retaining collar securing speedometer

cable
to
speedometer head.

4.
Remove screws retaining cluster
to
console.

5. Pull cluster forward
of
console opening and discon-

nect
all
wiring
and
lamp connections. Remove

cluster from vehicle.

CAUTION:
Do not
pull cluster outward further

than slack
in
wiring harness will allow, other-

Fig.
45-
Instrument Cluster Installation
—
Chevy
II

Fig.
46 -
Speed Warning Device

CHEVtOtET CHASSIS SERVICE MANUAL