engine overheat CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual

ENGINE-ELECTRICAL 6Y-33

O

V-8 ENGINE
STARTING MOTOR

Fig.
2s—V-8 Starting Circuit Diagram

2.

3.
From battery negative post
To
starting motor

housing.

From solenoid battery terminal
To
solenoid motor

terminal.

If voltage drop
in
any
of
above check exceeds 0.2 volts,

excessive resistance
is
indicated in that portion
of
start-

ing circuit
and the
cause
of the
excessive resistance

should
be
located
and
corrected
in
order to obtain maxi-

mum efficiency in the circuit.

CAUTION:
Do not
operate
the
starting motor

continuously
for
more than
30
seconds
to
avoid

overheating.

When
the
solenoid fails
to
pull
in, the
trouble may be

due
to
excessive voltage drop in the solenoid control cir-

cuit.
To
check
for
this condition, close
the
starting

switch
and
measure
the
voltage drop between
the
BAT-

TERY terminal of the solenoid and the
SWITCH (S)
termi-

nal
of
the solenoid.
1.
If
this voltage drop exceeds 3.5 volts, excessive
re-

sistance
in the
solenoid control circuit
is
indicated

and should be corrected.

2.
If the
voltage drop does not exceed 3.5 volts and the

solenoid does not pull in, measure the voltage availa-

ble
at
the SWITCH terminal
of
the solenoid.

3.
If the
solenoid does
not
feel warm,
it
should pull
in

whenever the voltage available
at
the SWITCH termi-

nal
is 7.7
volts
or
more. When
the
solenoid feels

warm,
it
will require
a
somewhat higher voltage
to

pull in.

STARTING MOTOR AND SOLENOID CHECK

The following checks
may be
made
if the
specific

gravity of the battery
is
1.215
or
higher.

1.
If the
solenoid does
not
pull in, measure the voltage

between
the
switch
(S)
terminal
of the
solenoid
and

ground with the starting switch closed.

CAUTION:
If the
solenoid feels warm, allow
to

cool before checking.

If
the
voltage
is
less than 7.7 volts, check for ex-

cessive resistance
in the
solenoid control circuit.

If
the
voltage exceeds 7.7 volts, remove the starting

motor
and
check
(1)
solenoid current draw,
(2)

starting motor pinion clearance,
and (3)
freedom of

shift lever linkage.

2.
If
the solenoid "chatters" but does not hold in, check

the solenoid
for an
open "hold-in" 'winding. When-

ever
it is
necessary
to
replace
a
starting motor

solenoid, always check starting motor pinion

clearance.

3.
If
motor engages
but
does
not
crank
or
cranks

slowly, check
for
excessive resistance
in the ex-

ternal starting circuit, trouble within
the
starting

motor,
or
excessive engine resistance
to
cranking.

SERVICE OPERATIONS

STARTING MOTOR

REMOVAL AND INSTALLATION (Fig.
3s)

The following procedure
is a
general guide
for all

vehicles
and
will vary slightly depending
on
series
and

model.

1.
Disconnect battery ground cable at battery.

2.
Raise vehicle
to a
good working height.

3.
Disconnect all wires
at
solenoid terminals.

NOTE: Reinstall
the
nuts
as
each wire
is
dis-

connected
as
thread size
is
different but may be

mixed and stripped.

4.
Loosen starter front bracket (nut on V-8 and bolt on

L-6) then remove two mount bolts.

5.
Remove
the
front bracket bolt
or nut and
rotate

bracket clear
of
work area then lower starter from

vehicle
by
lowering front end first
—
(hold starter

against bell housing
and
sort
of
roll end-over-end).

6. Reverse
the
removal procedure
to
install. Torque

the mount bolts
to
25-35
ft.
lbs. first, then torque

brace bolt.

7.
Check operation
of
starter on vehicle.
Fig.
3s—Starter Mounting

CHEVROLET CHASSIS SERVICE MANUAL

CLUTCH AND TRANSMISSIONS 7-3

•BUMPER

CLUTCH FORK

CLUTCH PEDAL

L-4 AND L-6 MODELS

Fig.
3 - Chevy II Clutch Pedal Free Travel Adjustment

to previous heat. The vehicle should be returned to the

Dealership the next day (at least 12 hours) to give clutch

time to cool to normal temperatures. Any slippage

should then be evaluated as follows:

1.
Drive in high gear at 20-25 MPH.

2.
Depress clutch pedal to the floor and rev engine to

2500-3500 rpm.

3.
Engage clutch quickly (snap foot off pedal) and press

accelerator to full throttle.

Engine speed should drop noticeably then accelerate

with vehicle. If clutch is bad, the engine speed will in-

crease.

NOTE: Do not repeat more than once or clutch

, will overheat.
-NUTC NUTC

SPACER F

SPACER F

RODB

' CLUTCH^ SWIVEL B

FORK

ADJUSTING
ROD
A '

V8 ENGINE
ADJUSTING
ROD
A

L6 ENGINE

Fig.
4 - Clutch Pedal Free Travel Adjustment

COMPONENT PARTS REPLACEMENT

CLUTCH ASSEMBLY

Removal From Vehicle

1.
Support engine and remove transmission as outlined

in transmission section.

2.
Disconnect clutch fork push rod and spring.
3.
Remove flywheel housing.

4.
Slide clutch fork from ball stud and remove fork from

dust boot.

NOTE: Ball stud is threaded into clutch hous-

ing and is easily replaced, if necessary.

CHEVROLET CHASSIS SERVICE MANUAL

CLUTCH AND TRANSMISSIONS 7-24

is at the full mark on the dip stick, it is just slightly be-

low the planetary gear unit. If additional oil is added,

bringing the oil level above the full mark, the planetary

unit will run in the oil, foaming and aerating the oil. This

aerated oil carried through the various oil pressure pas-

sages (low servo, reverse servo, clutch apply, converter,

etc.) may cause malfunction of the transmission assem-

bly, resulting in cavitation noise in the converter and

improper band or clutch application. Overheating may

also occur.

If the transmission is found consistently low on oil, a

thorough inspection should be made to find and correct

all external oil leaks.

PERIODIC OIL CHANGE

The transmission oil should be changed periodically as

recommended in Section 0, and whenever transmission is

to be removed from the vehicle for repairs.

1.
Run engine for one minute in neutral prior to chang-

ing.

2.
Be sure vehicle is level or raise from the rear only.

3.
Remove the oil pan drain plug and allow oil to drain

thoroughly into a pan or can.

Replace drain plug and refill with approximately two

quarts of oil specified in Section 0.

NOTE: To refill the transmission, remove dip

stick from oil filler tube and refill transmission

with oil specified in Section 0 using filler tube

and funnel J-4264. Then, after shifting into all

ranges at idle speed to fill all oil passages, the

engine should be run at 800-1000 rpm with the

transmission in Neutral until the oil warms up,

then add oil as required to raise the fluid level

to the full mark on the dip stick. Refill capacity

is approximately 2 qts.
4.

Fig.
1PG - Adjusting Low Band Using J-21848
PERIODIC LOW BAND ADJUSTMENT (Fig. 1PG)

Low band adjustment should be periodically performed

at 12,000 mile intervals, or sooner, as necessary if op-

erating performance indicates low band slippage.

1.
Raise vehicle and place selector lever in neutral.

2.
Remove protective cap from transmission adjusting

screw.

3.
a. On Corvette Models: Drop left exhaust pipe for

clearance.

b.
On Chevelle Models: To gain clearance between

underbody and transmission, it may be necessary

to remove rear mount bolts from crossmember,

and move transmission slightly toward passenger

side of vehicle. .

4.
Loosen adjusting screw lock nut 1/4 turn and hold in

this position with wrench.

5.
Using Special Tool J-21848 adjust band to 70 in. lbs.

and back off four (4) complete turns for a band which

has been in operation for 6,000 miles or more,.or

three (3) turns for one in use less than 6,000 miles.

CAUTION: Be sure to hold the adjusting screw

lock nut at 1/4 turn loose with a wrench during"

the.adjusting procedure.

6. Tighten the adjusting screw lock nut to specified

torque.

CAUTION: The amount of back-off is not an

approximate figure, it must be exact.

MANUAL SHIFT LINKAGE CHECK & ADJUST

(Column Type)

1.
The shift tube and lever assembly must be free in the

mast jacket. See Section 9 for alignment of steering

column assembly if necessary.

2.
To check for proper shift linkage adjustment, lift

the transmission selector lever towards the steering

wheel. Allow the selector lever to be positioned in

drive (D) by the transmission detent.

NOTE: Do not use the indicator pointer as a

reference to position the selected lever. When

performing linkage adjustment, pointer is ad-

justed last.

3.
Release the selector lever. The lever should be in-

hibited from engaging low range unless the lever is

lifted.

4.
Lift the selector lever towards the steering wheel,

and allow the lever to be positioned in neutral (N) by

the transmission detent.

5.
Release the selector lever. The lever should now

be inhibited from engaging reverse range unless the

lever is lifted.

6. A properly adjusted linkage will prevent the selector

lever from moving beyond both the neutral detent, and

the drive detent unless the lever is lifted to pass

over the mechanical stop in the steering column.

7.
In the event that an adjustment is required, place

the selector lever in drive (D) position as determined

by the transmission detent. See Steps 2 and 3.

8. Loosen the adjustment swivel at the cross-shaft,

and rotate the transmission lever so that it contacts

the drive stop in the steering column.

9. Tighten the swivel and recheck the adjustment. See

2 and 6.

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-29

Fig.
43b - Speed Warning Device

TEMPERATURE AND/OR OIL PRESSURE

GAUGE

1.
Disconnect battery ground cable.

2.
Remove ash tray and ash tray retainer.

3.
Disconnect A/C hose from the distributor duct.

4.
Disconnect wiring connectors and lamp bulbs from

rear of gauge.

5. Disconnect oil pressure pipe fitting from rear of oil

pressure gauge.

6. Remove (3) screws retaining gauge assembly to

cluster cover and disengage unit from cover.

7. Remove (4) retaining nuts and remove gauge from

template.

8. To install, reverse removal procedure.

INDICATOR LIGHT REPLACEMENT

To replace any indicator or cluster bulb, unsnap the

proper socket from rear of instrument cluster, remove

and replace bulb, and reinsert unit into rear of cluster

housing.
OIL PRESSURE INDICATOR

If the light does not come on when the ignition switch is

turned on, or if the light comes on and remains on after

the engine is started, one or more the following condi-

tions is indicated:

• Low oil pressure

• Defective wiring or switch

• High engine temperature

Switch Replacement

1.
Disconnect wiring harness connector from sender

unit terminal (located in block above starter on L-6

engines and at left front of distributor on V-8

engines).

2.
Remove sender unit using Tool J-21757, replace with

new unit, and check operation.

GENERATOR INDICATOR

Ignition on, Engine not Running and

Telltale Light Off

1.
Indicator bulb burned out, replace bulb.

2.
Open circuit or loose connection in the telltale light

circuit.

Telltale Light Stays on after Engine is Started

If indicator light does not go out at engine idle speed,

refer to' Charging Systems under Engine Electrical,

Section 6Y.

TEMPERATURE
(COOLING
SYSTEM)
INDICATOR

The temperature indicator circuit, consists of two re-

motely located units, indicator gauge and engine sender

unit. The indicator gauge on all models uses a single

red light to indicate an overheated engine condition.

Engine Sender Unit Replacement

1.
Drain engine cooling system to a level below unit.

2.
Remove sender unit (located in the inlet manifold

near water pump housing on V-8 engines and in the

cylinder head near an exhaust port on L-6 engines)

and replace with new unit.

3.
Refill cooling system and check operation of unit.

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-34

5. To replace, reverse the removal procedure.

SPEEDOMETER REPLACEMENT

1.
Remove instrument cluster as previously described

in this section.

2.
Remove clock set shaft knob.

3.
Remove eight screws securing cluster housing to

bezel trim panel. Separate parts carefully observing

stack up of parts.

4.
Remove two screws securing speedometer head to

rear of cluster housing.

NOTE:
Servicing of the speedometer head

should be performed by an authorized AC Speed-

ometer Service Station.

5. To install, reverse the removal procedure..

SPEEDOMETER CABLE

Replacement or Lubricatibn

1.
Disconnect the speedometer cable from the speed-

ometer head. Remove the old cable by pulling it out

from speedometer end of conduit.

NOTE:
If old cable is broken it may be neces-

sary to remove lower piece from transmission

end of conduit.

2.
Lubricate the lower 3/4 of cable with speedometer

cable lubricant and push the cable into the conduit.

Connect the upper end to the speedometer head and

road test vehicle for proper speedometer operation.

INDICATOR LIGHT REPLACEMENT

To replace any indicator or cluster bulb, unsnap the

proper socket from rear of instrument cluster, remove

and replace bulb, and reinsert unit into rear of cluster

housing.

OIL PRESSURE INDICATOR

If the light does not come on when the ignition switch
is turned on, or if the light comes on and remains on

after the engine is started, one or more of the following

conditions is indicated:

• Low oil pressure

• High engine temperature

• Defective wiring or switch

Switch Replacement

1.
Disconnect wiring harness connector from sender

unit terminal (located in block above starter on

L-6 engines and at left front of distributor on V-8

engines).

2.
Remove sender unit, replace with new unit, and

; check operation.

GENERATOR INDICATOR

1.
Ignition on, engine not running and telltale light off.

a. Indicator bulb burned out, replace bulb.

b.
Open circuit or loose connection in the telltale

light circuit.

2.
Telltale light stays on after engine is started.

a. If indicator light does not go out at engine idle

speed, refer to Charging Systems under Engine

Electrical, Section 6Y.

TEMPERATURE (COOLING SYSTEM) INDICATOR

The temperature indicator circuit consists of two re-

motely located units, indicator gauge and engine sender

unit. The indicator gauge on all models uses a single

red light to indicate an overheated engine condition.

Engine Sender Unit Replacement

1.
Drain engine cooling system to a level below unit.

2.
Remove sender unit (located in the inlet manifold

near water pump housing on V-8 engines and in the

cylinder head near an exhaust port on L-6 engines)

and replace with new unit.

3.
Refill cooling system and check operation of unit.

CORVETTE INSTRUMENTS AND GAUGES

INDEX

Page

General Description ., 12-34

Service Operations . 12-35

Instrument Cluster ., 12-35

Fuel Gauge 12-35
Speedometer/Tachometer Service. 12-35

Temperature Gauge 12-35

Ammeter/Oil Pressure Gauges 12-35

GENERAL DESCRIPTION

All Corvette instruments and gauges are conveniently

located in the dash-mounted cluster. The entire cluster

is removable to permit servicing of the various instru-

ments and gauges. The indicator and cluster illuminating

bulbs may be replaced without removing the cluster from

the panel.
Regular maintenance is not required on the instrument

cluster or its components other than maintaining clean

and keeping the speedometer and tachometer cables

properly lubricated.

CHEVROLET CHASSIS SERVICE MANUAL