fog light CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual

HEATER AND AIR CONDITIONING 1A-19

Transducer

The transducer will produce a vacuum output that is

completely adjustable by varying the input voltage which

is provided by the amplifier. An increase in the applied

voltage results in a reduced vacuum output.

Power Servo

The power servo receives a vacuum signal from the

transducer, and it is capable of assuming any position

that is called for by the sensors, amplifier, and trans-

ducer. The power servo performs the following functions:

1.
Positions the temperature mix door via the tern-

perature door link. The position of this door~"de-

termihes the portions of hot and cold air being

blended and discharged into the car.

2.
Operates the power servo vacuum valve which de-

termines the air flow paths for heating and air

conditioning.

3.
Contains a printed circuit board which controls the

blower speed. The power servo position determines

the blower speed, but the control lever switch can

override the blower program depending upon the

customer's preference.

4.
Contains the "Hi" blower delay thermistor and the

"master delay thermistor".

Outside Air Diaphragm

When there is no vacuum applied to the hose, the out-

side air door is closed under spring tension. With the

door closed, air is taken from the inside of the auto-

mobile and re-circulated. Applying vacuum to the dia-

phragm opens the door for outside air.

Mode Door Diaphragm

Located behind the duct work, the mode door diaphragm

directs the air flow out either the air conditioning outlets,

the heater floor outlet, or both the heater and air con-

ditioning outlets. This is a push-pull type diaphragm

actuated by vacuum through two hoses and controlled by

the power servo vacuum switch.

Defroster Door

The defroster door is in the defog position until vacuum

is applied to the actuator to obtain either full heat or full

de-ice position.

High Blower Delay Thermistor

The high blower delay thermistor is located on the

power servo housing under the power servo vacuum valve

and printed circuit board assemblies. The function of the

thermistor is to operate the blower at a reduced speed

when the control is in the HI FRONT position until the

residual cold air is discharged from the duct work. This

function occurs when the blower first comes "on" in cold

weather.

Vacuum Tank

During heavy acceleration, the vacuum supply from
the carburetor drops. The vacuum tank, using a^ check

valve, stores vacuum so that under these conditions

vacuum will be available for the Comfortron.

Thermal Vacuum Valve (Hot Water Vacuum Switch)

When engine coolant temperature reaches 75°F, the

valve opens and supplies vacuum to the outside air door

if the system is calling for outside air.

Master Delay Thermister

This thermistor delays the initial operation of the

blower when the system is in the heat mode. In cold

weather this allows outside ram air to flow through the

system thereby purging the cold air in the ducts gradually

until the coolant reaches about 105°F. Then, the termis-

tor passes enough current to energize the master delay

relay which powers the blower at about nine volts.

Vacuum Relay Valve

This relay valve will shut off transducer vacuum to the

power servo whenever the vacuum from the engine intake

manifold falls below the vacuum in the power servo

supply line (engine stopped or operating at low manifold

vacuum). This causes the power servo to be held in

position when the vacuum supply falls too low to maintain

servo control.

Vacuum Bleeder

A vacuum bleeder insures that the outside air door will

close (diaphragm will bleed down) after the system has

been shut down. This prevents outside air from entering

when starting the system on a cold day before the engine

coolant temperature reaches 75°F.

Sun—Ambient Sensor

The sun-ambient sensor measures the temperature of

the air entering the air intake grille in front of the wind-

shield. The sensor is exposed to sun light so that it can

lower the in-car temperature slightly when the sun

is shining.

Ambient Switch

The ambient switch operates the air conditioning com-

pressor clutch. When the outside temperature is above

40° F. the switch will be closed and the compressor will

be running. This switch is included as| part of the sun-

ambient sensor assembly, but operates independently.

Resistor Assembly

The blower resistors are located in the evaporator

housing. The printed circuit board switch in the power

servo determines which of the resistors is being used,

and as in conventional systems, the resistors control the

blower speed.

System Operation

When starting the Comfortron System in cold weather,

the following sequence of events occurs:

1.
Initially the system is inoperative. In LO FRONT

position the master delay thermistor is warming

(self-heating because current is flowing through it)

CHEVROLET CHASSIS SERVICE MANUAL