lug pattern CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual

CLUTCH
AND
TRANSMISSIONS
7-20

COMPONENT PARTS REPLACEMENT

3.

4.

5.

6.
TRANSMISSION REPLACEMENT
(EXC.
CORVETTE)

Removal From Vehicle

1.
Remove shift lever trim plate and dust boot.

Remove shift lever assembly.

Raise vehicle
to
desired working height.

Disconnect
the
speedometer cable from speedometer

driven gear fitting.
.
~
. •

Remove propeller shaft, then support engine
at the

oil
pan
rail with
a
jack
or
other suitable support

capable
of
supporting
the
engine when transmission

is removed.

Disconnect shift lever bracket assembly from exten-

sion
and
remove
all 3
transmission shifter levers

from shifter shafts, (leave linkage connected
to

levers)
and
remove bracket assembly levers
and

linkage.

Remove extension mount7 to-crossmember attaching

bolts.

Loosen transmission crossmember
and
move rear-

ward
or
remove.

Remove
the
transmission-to-clutch housing retaining

bolts
and
install two guide pins, J-1126,
in
top holes.

Slide
the
transmission straight back until
the
input

shaft
is
free
of
splines
in the
clutch disc.

Slide
the
transmission rearward
to
allow sufficient

clearance
of
input shaft
and
clutch housing. Then tilt

input shaft
end of
transmission downward and with-
8.

9.

10.

11.
draw transmission from vehicle.

installation
to
Vehicle

1.
Raise transmission
and
rotate
as
necessary-to start

input shaft into clutch disc
and
slide transmission

forward until
it
bottoms against clutch housing.
Re-

move guide pins.

2.
Install
the
transmission-to-clutch housing retaining

bolts.
Torque
all
four retaining bolts
to 50 ft. lbs.

3.
Raise engine
and
position extension mount
to
cross-

member,
and
loosely install
the
retaining bolts.

Tighten crossmember
to
frame retaining bolts.

4.
Remove temporary support from engine, and torque

the extension mount retaining bolts.

5. Install propeller shaft.

6. Install control lever bracket assembly
to
transmis-

sion extension
and
connect shifter levers
to
shifter

shafts.

7. Fill transmission
to
level
of
filler plug hole with

correct lubricant specified
in
Section
0.

8. Lower vehicle and install shift lever assembly, check

shift pattern and adjust linkage
as
required.

9. Install trim plate and dust boot.

CORVETTE TRANSMISSION REPLACEMENT

Refer
to
similar procedure under 3-Speed Corvette

Transmission.

FOUR-SPEED (SAGINAW) TRANSMISSION

INDEX

Page

General Description
7-20

Maintenance
and
Adjustments
. . 7-21

Shift Linkage Adjustment.
. 7-21

Speedometer Driven Gear
and

Oil Seal ................
(See
Muncie 4-Speed)

Side Cover
7-22
Page

Removal
. . , 7-22

Disassembly
. . 7-22

Assembly
. . . 7-22

Installation
. 7-22

Extension
Oil
Seal
(See
Muncie 4-Speed)

Transmission Replacement (See Muncie 4-Speed)

GENERAL DESCRIPTION

The Saginaw four speed fully synchronized
(all
forward

gears) transmission incorporates helical drive gears

throughout.

The main drive gear
is
supported
by a
ball bearing
at

the front
end of the
transmission case and
is
piloted
at its

front
end in an oil
impregnated bushing mounted
in the

engine crankshaft.
The
front
end of the
mainshaft
is

piloted
in a row of
roller bearings
set
into
the
hollow
end

of
the
main drive gear
and the
rear end
is
carried
by a

ball bearing mounted
in the
front
of the
extension housing.

The countergear
is
carried
on a
single
row of
rollers

at both ends while thrust
is
taken on thrust washers
lo-

cated between
the
ends
of the
gear and
the
thrust bosses

in
the
case. Ah anti-rattle plate assembly
at the
front
of

the countergear provides
a
constant spring tension
be-

tween
the
counter
and
clutch gears
to
reduce torsional

vibrations.
The
sliding reverse idler gear
is
carried
on

a bushing finish bored
in
place.
It
rotates
on a
short

idler shaft retained by
a
woodruff
key.

The synchronizer assemblies consist
of a
clutch
hub,

clutch sleeve,
two
clutch
key
springs and three energizer

clutch keys
and are
retained
as an
assembly on
the
main

shaft
by a
snap ring.
A great deal
of
similarity
and
interchangeability
now

exists between
the new 3 and
4-speed Saginaw trans-

missions.

However,
the
synchronizer assembly
at the
front
of the

mainshaft
is
used
for the
third and fourth rather than
the

second
and
third shift.
The
synchronizer assembly
at

the rear
of the
mainshaft
is
used
for the
first and second

rather than
the
first
and
reverse shift. Gear teeth
cut

in
the
first and second synchronizer sleeve (reverse gear)

distinguish
it
from
the
third
and
fourth synchronizer

sleeve.

Starting from
the
front, gears
on the
mainshaft
are

third, second
and
first rather than second, first and
re-

verse.
A
fourth blocker ring
is
used between
the 1-2

synchronizer assembly
and
first gear
on the
four-speed

transmissions.

The cover
on the new
four-speed transmission
is lo-*

cated
on the
left-hand side
of the
case.
It is
similar
to

the three-speed cover with
the
addition
of a
reverse

shifter shaft assembly, detent ball
and
detent spring.

Disassembly
and
assembly procedures
are
covered
in

this section.

CHEVROLET CHASSIS SERVICE MANUAL

WHEELS AND TIRES 10-4

the road and it slips, grinding off the tread on the inside

half of the tire at an excessive rate. This type of tire

shows much the same appearance of tread wear as tire

wear caused by negative camber.

Second, the transfer of weight may also over-load the

outside tires so much that they are laterally distorted

resulting in excessive wear on the outside half of the

tire producing a type of wear like that caused by ex-

cessive positive camber.

Cornering wear can be most easily distinguished from

abnormal camber wear by the rounding of the outside

shoulder or edge of the tire and by the roughening of the

tread surface which denotes abrasion.

Cornering wear often produces a fin or raised portion

along the inside edge of each row in the tread pattern.

In some cases this fin is almost as pronounced as a

toe-in fin, and in others, it tapers into a row of tread

blocks to such an extent that the tire has a definite step

wear appearance.

The only remedy for cornering wear is proper in-

struction of owners.

Fig.
5 - Tire Rotatidh

Rotation

To minimize the possibility of tire noise and to equal-

ize tire wear, it is recommended that tires be inter-

changed every 6000 miles as shown in Figure 5 or more

frequently in the case of extremely heavy wear.

NOTE:
Rotate Corvette tires at 4000 miles or

sooner.

Interchanging tires will effectively prevent undue wear

on any particular tire. II tire interchanging is followed

as recommended above, all tires will have the same

number of miles in each wheel position at the end of the

fourth change. When interchanging tires, inspect for

signs of abnormal wear, bulging, etc., stones, glass, and

nails should be removed before reinstallation.

Noise

Noise caused by the normal action of tire treads on

various road surfaces is often confused with rear axle
gears or other noises in the car.

The determination of whether tires are causing the

noise complained of is relatively simple. The car should

be driven at various speeds and note taken of part

throttle, and sudden acceleration and deceleration. Axle

and exhaust noises show definite variations under these

conditions, while tire noise will remain constant. Tire

noise is, however, most pronounced at speeds of approx-

imately twenty or thirty miles per hour.

The tires may be further checked by driving the ear

over smooth pavement with the tires at normal pressure

and again over the same stretch of pavement when the

tires have been inflated to fifty pounds pressure. Reduce

the tires to normal pressure one at a time to determine

the faulty tire or tires. This high inflation pressure

should immediately be reduced to normal after test. If

the noise for which the test is being made is caused by

tires,.
it will noticeably decrease when the tire pressure

is increased, whereas axle noise should show no change

in volume.

If, on inspection, the tires on the front wheels are

found to be creating most of the noise the alignment of

the front wheels should be checked. Excessive tire noise

usually results from lower than recommended tire pres-

sure, incorrect alignment, uneven tire wear, or defective

(thumper) tire.

Cleaning

A great deal of ordinary road dirt which collects on

white sidewall tires may be sponged off with clear water

or a mild soap solution.

A good brand of whitewall tire cleaner, however, is

a quicker and more effective cleaner for removing dirt

and stains from whitewall tires and in many cases it

will remove stains and discoloration that the simpler

method of soap and water will not remove.

Under no circumstances should gasoline, kerosene or

any cleaning fluid containing a solvent derived from oil

be used to clean whitewall tires. Oil in any form is

detrimental to tire rubber and a cleaner with an oil base

will discolor or injure whitewall tires.

Change (W/Wheels)

To change the road wheels using the jack that comes

with the car, observe the following procedure:

1.
Set hand brake and block front wheels if rear wheel

is being changed.

2.
Remove hub cap or wheel disc and break wheel

mounting nuts loose.

3.
Place the jack as directed tinder, General Informa-

tion,
Section 0 and raise car until wheel clears

ground.

4.
Remove wheel mounting nuts and remove wheel from

hub or drum.

5. To replace road wheel, reverse the above instrue-

. tions. Proper torque on nuts is 55-75 ft. lbs.

torque (70-85 ft. lbs. for Corvette aluminum wheel

nuts).

CAUTION: On models equipped with discs, in-

dex the pilot hole in the disc on the valve stem.

(To insure that the anti-rotation notches in wheel

disc register on lugs in wheel rim.)

CHEVROLET CHASSIS SERVICE MANUAL