refrigerant type CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual

HEATER
AND AIR
CONDITIONING
1A-13

AIR CONDITIONING

INDEX

Page

General Description
1A-13

Four-Season System
1A-13

Controls
1A-16

Comfortron System
. 1A-18

System Components
lA-19

Controls
1A-20

Universal System
. .
1A-21

Chevy
n
All-Weather System
•
1A-21

Corvette Four-Season System
. 1A-22

General Information
. . . 1A-26

Precautions
in
Handling R-12
1A-26

Precautions
in
Handling Refrigerant Lines
1A-28

Maintaining Chemical Stability
in the

Refrigeration System
1A-28

Gauge
Set 1A-29

Charging Station
IA-29

Leak Testing
the
System
1A-29

Vacuum Pump
1A-30

Availability
of
Refrigerant-12
. . 1A-30

Compressor
Oil 1A-31

Compressor Serial Number
1A-31

Inspection
and
Periodic Service
1A-31

Pre-Delivery Inspection
1A-31

6,000 Mile Inspection
1A-32

Periodic Service
, 1A-32

Installing Gauge
Set to
Check System Operation
....
1A-32

Performance Test
1A-32

Performance Data lA-r33

Comfortron System Operational Test
1A-33

Chevrolet Comfortron Tester
1A-34

Complete System Checks
1A-35

Maintenance
and
Adjustments ......
1A-37

Evaporator Comtrol Valve (POA)
.
1A-37
Page

Thermostatic Switch
1A-37

Expansion Valve
1A-41

Engine Idle Compensator
. . .
1A-42

Evacuating
and
Charging Procedures
1A-42

Purging
the
System
1A-42

Evacuating
and
Charging
the
System
1A-43

Checking
Oil . 1A-43

Component Replacement
and
Minor Repair
1A-45

Refrigerant Line Connections
1A-45

Repair
of
Refrigerant Leaks
1A-46

Preparing System
for
Replacement
of

Component Parts
. 1A-46

Foreign Material
in the
System
.
1A-47

Condenser
.
1A-48

Receiver-Dehydrator
1A-48

Evaporator
1A-49

Expansion Valve
1A-57

Evaporator Control Valve (POA)
1A-59

Thermostatic Switch
or
Blower Switch
. .
1A-59

All Weather-Pull Cable
1A-61

Blower Assembly
1A-62

Air Inlet Valve
.
1A-64

Blower
and
Evaporator Assembly
1A-64

Air Distributor Assembly
and
Outlet Ducts ...... 1A-64

Comfortron Automatic Control Components
1A-66

Collision Procedure lA-70

Four-Season Heater Components
1A-73

Comfortron Heater Components
. . . 1A-75

Compressor
1A-76

Wiring Diagrams
1A-78

Special Tools
.
1A-84

GENERAL DESCRIPTION

Four
air
conditioning systems
are
covered
in
this

section. They are:

1.
The
Four-Season System (Chevrolet, Chevelle,

Camaro and Corvette).

2.
The Comfortron System (Chevrolet).

3.
The All Weather System (Chevy n).

4.
The Universal System (Chevrolet, Chevelle, Chevy
n,

Camaro)

Underhood components (that
is, the
compressor,
con-

denser
and
receiver-dehydrator)
are
much
the
same
in

type,
location
and
method
of
attachment
on all of
the

above systems. The six-cylinder reciprocating compres-

sor
is
bracket-mounted
to the
engine
and
belt driven

from
the
crankshaft pulley.
The
condenser
is
mounted

ahead
of the
engine cooling radiator
and the
receiver-

dehydrator
is
mounted
in
the refrigerant line downstream

of
the
condenser.
All
cooling system components
are

connected by means
of
flexible refrigerant lines.

Evaporator size
and
location differ from system
to

system
as do
methods
of
temperature control
and air

supply
and
distribution.

FOUR-SEASON SYSTEM

The Four-Season system used
in the
Chevrolet,

Chevelle, Camaro,
and
Corvette vehicles
may be
iden-

tified
by the
fact that
it
uses
an
evaporator pressure

control known
as the POA
(Pressure Operated Absolute)

suction throttling valve.
Both
the
heating
and
cooling functions
are
performed

by this system.
Air
entering
the
vehicle must pass

through
the
cooling unit (evaporator)
and
through
(or

around)
the
heating unit,
in
that order, and the system
is

thus referred to
as a
''reheat" system.

The evaporator provides maximum cooling
of the air

passing through
the
core when
the air
conditioning sys-

tem
is
calling
for
cooling.
The
control valve acts in the

system only
to
control
the
evaporator pressure
so
that

minimum possible temperature
is
achieved without core

freeze-up.
The
valve
is
preset,
has no
manual con-

trol,
is
automatically altitude compensated,
and non-

repairable.

The heater core will be hot
at
all times since no water

valve
is
present
in
the system.

System operation
is as
follows (See Figure 24 and 25):

Air, either outside
air or
recirculated
air
enters
the

system
and is
forced through
the
system by the blower.

As
the air
passes through
the
evaporator core,
it

receives maximum cooling
if
the
air
conditioning controls

are calling
for
cooling. After leaving
the
evaporator,

the
air
enters
the
Heater
and Air
Conditioner Selector

Duct Assembly where,
by
means
of
manually operated

diverter doors,
it is
caused
to
pass through
or to
bypass

the heater core
in the
proportions necessary
to
provide

the desired outlet temperature. Conditioned airflow then

enters
the
vehicle through either
the
floor distributor

duct
or the
dash outlets. Remember that the heater core

CHEVROLET CHASSIS SERVICE MANUAL

HEATER AND AIR CONDITIONING 1A-29

time as possible will be required to perform the

operation. Don't leave the system open any longer

than is necessary.

• Finally, after the operation has been completed and

the system sealed again, air and moisture should be

evacuated from the system before recharging.

GAUGE SET

The gauge set (fig. 41) is used when purging, evacua-

ting, charging or diagnosing trouble in the system. The

gauge at the left is known as the low pressure gauge.

The face is graduated into pounds of pressure and, in

the opposite direction, in inches of vacuum. This is the

gauge that should always be used in checking pressures

on the low pressure side of the system. When all parts of

the system are functioning properly the refrigerant

pressure on the low pressure side never fails below 0

pounds pressure. However, several abnormal conditions

can occur that will cause the low pressure to fall into a

partial vacuum. Therefore, a low pressure gauge is

required.

The high pressure gauge is used for checking pres-

sures on the high pressure side of the system.

The connection at the left is for attaching the low

pressure gauge line and the one at the right the high

pressure gauge line. The center connector is common to

both and is for the purpose of attaching a line for adding

refrigerant, discharging refrigerant, evacuating the sys-

tem and other uses. When not required, this line or

connection should be capped.

NOTE:
Gauge fitting connections should be in-

stalled hand tight only and the connections leak

tested before proceeding.

The hand shutoff valves on the gauge manifold do not

control the opening or closing off of pressure to the

gauges. They merely close each opening to the center

connector and to each other. During most diagnosing

and service operation, the valves must be closed. The

only occasion for opening both at the same time would be

to bypass refrigerant vapor from the high pressure to

the low pressure side of the system, or in evacuating

both sides of the system.

CHARGING STATION

The J-8393 Charging Station is a portable assembly of

a vacuum pump, refrigerant supply, gauges, valves, and

most important, a five (5) pound metering refrigerant

charging cylinder. The use of a charging ey'inder elim-

inates the need for scales, hot water pails, etc.

The chief advantage of this unit is savings. A very

definite savings in refrigerant and time can be obtained

by using this unit. Since the refrigerant is metered into

the system by volume, the correct amount may be added

to.
the system and charged to the customer. This, coupled

with the fact that the unit remains "plumbed" at all times

and thus eliminates loss of refrigerant in purging of

lines and hooking-up, combines to enable the operator to

get full use of all refrigerant purchased by the

dealership.

All evacuation and charging equipment is hooked to-

gether in a compact portable unit (fig. 42) which brings

air conditioning service down to the basic problem of

hooking on two hoses, and manipulating clearly labeled

valves.
Fig.
42—System Charging Station

This will tend to insure that the job will be done without

skipping operations. As a result, you can expect to save

time and get higher quality work, less chance of an over

or undercharge, or comeback.

The pump mount is such that the dealer may use his

own vacuum pump. The gauges and manifold are in com-

mon use. Thus a current air conditioning dealer can use

the equipment on hand and avoid duplication.

LEAK TESTING THE SYSTEM

Whenever a refrigerant leak is suspected in the system

or a service operation performed which results in dis-

turbing lines or connections, it is advisable to test for

leaks.
Common sense should be the governing factor in

performing any leak test, since the necessity and extent

of any such test will, in general, depend upon the nature

of the complaint and the type of service performed on

the system. It is better to test and be sure, if in doubt,

than to risk the possibility of having to do the job over

again.

NOTE:
The use of a leak detecting dye within

the system is not recommended because of the

following reasons:

1.
Refrigerant leakage can exist without any oil leakage.

In this case the dye will not indicate the leak, how-

ever, a torch detector will.

2.
The addition of additives, other than inhibitors, may

alter the stability of the refrigeration system and

cause malfunctions.

3.
Dye type leak detectors which are insoluble form a

curdle which can block the inlet screen of the ex-

pansion valve.

CHEVROLET CHASSIS SERVICE MANUAL

HEATER AND AIR CONDITIONING 1A-30

Leak Detector

Tool J-6084 (fig. 43) is a propane gas-burning torch

which is used to locate a leak in any part of the system.

Refrigerant gas drawn into the sampling tube attached to

the torch will cause the torch flame to change color in

proportion to the size of the leak. Propane gas fuel

cylinders used with the torch are readily available

commercially throughout the country.

CAUTION: Do not use lighted detector in any

place where combustible or explosive gases,

dusts or vapors may be present;

Operating Detector

1.
Open control valve only until a low hiss of gas is

heard, then light gas at opening in chimney.

2.
Adjust flame until desired volume is obtained. This

is most satisfactory when blue flame is approxi-

mately 3/8" above reactor plate. The reaction plate

will quickly heat to a cherry red.

3.
Explore for leaks by moving the end of the sampling

hose around possible leak points in the system. Do

not pinch or kink hose.

NOTE: Since R-12 is heavier than air, it is

good practice to place open end of sampling tube

immediately below point being tested, partic-

ularly in cases of small leaks.

CAUTION: Do not breathe the fumes that are

produced by the burning of R-12 gas in the de-

tector flame, since such fumes can be toxic in

large concentrations of R?»12.

4.
Watch for color changes. The color of the flame

which passes through the reaction plate will change

to yellow when sampling hose draws in very small

CHIMNEY

REACTION PLATE

BURNER HEAD

Fig.
43—Leak Detector
leaks of R-12. Large leaks will be indicated by a

change in color to a vivid purplish-blue. When the

sampling hose passes the leak, the flame will clear

to an almost colorless pale-blue again. If the flame

remains yellow when unit is removed from leak,

insufficient air is being drawn in or the reaction

plate is dirty.

NOTE: A refrigerant leak in the high pressure

side of the system may be more easily detected

when, if possible, the system is in operation. A

leak on the low pressure side may be most

easily detected after the engine has been shut

off for several minutes to allow system pres-

sures to equalize. This particularly applies to

the front seal.

VACUUM PUMP

A vacuum pump should be used for evacuating air and

moisture from the air conditioning system.

Vacuum pump, Tool J-5428, (fig.. 44) is available for

this purpose. It is used as a component part of the

Charging Station J-8393, described previously. The fol-

lowing precautions should be observed relative to tbe

operation and maintenance of this pump.

' • Make sure dust cap on discharge outlet of vacuum

pump is removed before operating.

• Keep all openings capped when not in use to avoid

moisture being drawn into the system.

• Oil should be changed after every 250 hours of nor-

mal operation.

To change oil, simply unscrew hex nut located on

back side of pump, tilt backward and drain out oil

(fig. 44). Recharge with 8 ounces of vacuum pump

oil.
If you desire to flush out the pump, use this

same type clean oil. Do not use solvent.

NOTE: Improper lubrication will shorten the

life of pump.

• If this pump is subjected to extreme or prolonged

cold, allow it to remain indoors until oil has reached

approximate room temperature. Failure to warm oil

will result in a blown fuse.

• A five ampere time delay cartridge fuse has been

installed in the common line to protect the windings

of the compressor. The fuse will blow if an ex-

cessive load is placed on the pump. In the event the

fuse is blown, replace with a five ampere time delay

fuse - do not use a substitute fuse as it will result in

damage to the starting windings.

• If the pump is being utilized to evacuate a burnt-out

system, a filter must be connected to the intake

fitting to prevent any sludge from contaminating the

working parts, which will result in malfunction of the

pump.

• Do not use the vacuum pump as an air compressor.

AVAILABILITY OF REFRIGERANT-12

Refrigerant-12 is available through Parts Stock in 25

lb.
drums and in 15 oz. disposable cans. Valves are

available for
the"
disposable cans, which may be used as

individual cans or as a group of up to four cans (fig. 45).

Tool J-6272 is used with one through four cans. The

use of the four-can fixture makes it possible to charge

the system with a known quantity of refrigerant without

CHEVROLET CHASSIS SERVICE MANUAL

HEATER AND AIR CONDITIONING 1A-59

Fig.
78—Evaporator Mounting (Corvette)

7. Check the system for proper operation.

Universal System

Follow the procedure outlined under " Evaporator" for

the Universal System.

Chevy II All-Weather System

Replacement of Valve Assembly

1.
Purge the system of refrigerant and remove the

evaporator unit from the vehicle and the core from

the unit as described under "Evaporator."

2.
Remove the expansion valve power element bulb and

the equalizing line connection from the low pressure

line.

3.
Remove the low pressure and high pressure lines

from the valve. Remove the valve.

4.
Install the new valve by connecting the low pressure,

high pressure and* equalizing line connections and

clamp the power element of the new valve to the low

pressure line.

5. Replace the core and evaporator as covered under

"Evaporator."

EVAPORATOR CONTROL VALVE (POA)

(Chevrolet, Chevelle, Comoro, Corvette)

No repairs or adjustments are available on the POA

valve. A malfunctioning valve must be replaced. Figures

80,
81, 82 and 83 illustrate valve installation on the above

vehicles.

THERMOSTATIC SWITCH OR BLOWER SWITCH

Universal System

Removal

1.
Remove the screws attaching the cover plate to the

unit and pull the cover rearward.

2.
(Fin sensing type) Remove the thermostatic capillary

tube from the evaporator core to permit access to

the back of the cover plate.
Fig.
79—Evaporator Core Removal (Corvette)

Fig.
80-P.O.A. Installation (Chevrolet)

CHEVROLET CHASSIS SERVICE MANUAL

SPECIFICATIONS

HEATING
AND AIR
CONDITIONING

SECTION
1A

Compressor

Make Frigidaire

Type
. 6
Cylinder Axial

Displacement

Four-Season
12.6
Cu.
In.

Universal
and
Ail-Weather
.... .10.8 Cu. In.

Rotation Clockwise

Compressor Suction
and
Discharge

Connector Bolt Torque
.......
25 ft lbs.

Compressor Clutch Coil

Ohms
(at
80°F.).
4.18-4.38

Amps
(at
80°F.)
2.86 @ 12
Volts

Torques

Rear Head
to
SheU Stud
Nut 23 lb. ft

Shaft Mounting
Nut 15 lb. ft

Belt Tension.
See
Tune-Up Chart
System Capacities

Refrigerant
R-12

Four-Season
and
Comfortron

Systems.
............
3 lbs., 12 oz.

Universal Systems

Chevrolet, Chevelle,
and
Camaro.
... 3 lbs.

Chevy
n 2 lbs. 8 oz.

All-Weather System
2 lbs. 8 oz.

Compressor
Oil 525
Viscosity

All Systems
11 oz.

Fuses

Comfortron Systems
.

Four-Season Systems
.

Universal Systems
. .

All-Weather System.
.
Fuse

Block

25
amp.

25
amp.

25
amp.

25
amp.
In

Line

30
amp.

30
amp.

20
amp.

20
amp.

SECTION
3

WHEEL ALIGNMENT SPECIFICATIONS (Vehicle
dt
Curb Weight)

Caster*

Camber*

Steering Axis

Inclination

tToe-In (Total)

Wheel Bearing

Adjustment

Preload

End Movement
Chevrolet

Pos.
3/4° ± 1/2°

Pos.
1/4° ± 1/2°

7-1/2° ± 1/2°

@l/8"
to 1/4"

12 ft lbs.

zero

.001"
to .008"
Chevelle •

(SS and El Camino)

Neg. 1/2° ± 1/2°

(All others)

Neg. 1° ± 1/2°

Pos.
1/2° ± 1/2°

8-1/4° ± 1/2°

1/8" to 1/4"

12 ft lbs.

zero

.001"
to .008"
Chevy n

Pos.
1° ± 1/2°

Pos.
1/2° ± 1/2°

7° ± 1/2°

1/4" to 3/8"

12 ft lbs.

zero

.000"
to .004"
Corvette

Pos.
1° ± 1/2°

Pos.
3/4° ± 1/2°

7° ± 1/2°

3/16" to 5/16"

12 ft lbs.

zero

.001"
to .008"
Camaro

Pos.
1/2° £ 1/2°

Pos.
1/4° ±1/2°

8 3/4° ± 1/2°

1/8" to 1/4"

12 ft lbs.

zero

.001"
to .008"

•Must not vary more than 1/2° from side to side.

@Toe-In (Total) should be 5/16" to 7/16" after rebuild using new bushings and ball joints.

tAdjust Toe-in with steering gear on straight ahead location after camber and caster have been set Any change

in caster and camber settings will affect toe; always recheck and set toe to specifications.

LET CHASSIS SERVICE MANUAL