display CHEVROLET CORVETTE 2002 5.G Service Manual

3-5
Driver Set Temperature Knob
The DRIVER knob changes the temperature on
the driver's and passenger's side of the vehicle.
Turn the knob clockwise to increase the temperature
and counterclockwise to decrease the temperature.
Whenever you turn this knob, the temperature will be
displayed for approximately five seconds along with
the current fan speed and air delivery mode.
When adjusting the temperature, start with a driver
-set
temperature of 73
F (23
C) until you determine
your comfort zone. If you choose 60
F (16
C),
the system will remain at maximum cooling and will
not automatically adjust fan speed or air delivery.
If you choose 90
F (32
C), the system will remain at
maximum heating and will not automatically adjust fan
speed or air delivery. Choosing either maximum setting
will not cause the system to heat or cool any faster.
Turning the knob past either maximum setting has
no effect on the operation of the system.Passenger Temperature Offset
The PASSENGER knob changes the temperature on the
passenger's side of the vehicle. When the knob is in the
12 o'clock position, the passenger's temperature is the
same as the driver's. Turn the knob clockwise for warmer
air on the passenger's side, counterclockwise for cooler
air. If the driver
-set temperature is set at 60
F (16
C) or
90
F (32
C), turning the passenger knob has no effect
because the system is locked at a maximum setting.
Automatic Operation
Press the AUTO button to place the entire system in
the automatic mode. After a five
-second display of the
current settings, only the word AUTO and the outside
temperature will be shown on the digital display
unless you are in full cold 60
F (16
C) or full hot
90
F (32
C), then the word AUTO will not display.
The system will operate to achieve your comfort set
temperature as quickly as possible. The AUTO control
system works best with the windows up and the
removable roof installed or the convertible top up.

3-7
Manual Settings
With the automatic electronic dual climate control
system, there are several manual settings you can use
to control the system and override the AUTO operation.
You can program the fan speed, air delivery mode, air
intake mode and control the air conditioning operation
using these settings. The system will still determine the
temperature output level based on the driver
-set
temperature and the passenger temperature offset.
(Fan Speed): Press the button with the fan symbol
on it to manually lock in the current fan speed and to
stop the automatic fan speed control. Pressing the
arrows will delete AUTO from the digital display.
The fan graphics with the fan speed bars will be shown.
To increase the fan speed so that more air flows into
the vehicle, press the up arrow on the fan switch.
To decrease the fan speed and airflow, press the down
arrow. The AUTO button must be pressed to return
to the automatic fan control.MODE: Press the MODE button to manually lock in
the current air delivery setting and to stop the automatic
mode control. Pressing the MODE button will delete
AUTO from the digital display and the mode graphics
will be shown. To change the setting, press the MODE
button again. The AUTO button must be pressed to
return to the automatic mode selection.
(Vent): This setting directs most of the air through
the instrument panel outlets and a very small amount to
the lower outlets.
(Bi-Level): This setting directs air into the vehicle
in two ways. Cooler air is directed toward your upper
body through the instrument panel outlets, while warmer
air is directed through the lower outlets.
(Floor): This setting directs most of the air to the
floor area and some of it toward the windshield and side
window vents.
(Defog): This setting divides the air between
the windshield and lower outlets and a small amount
toward the side window vents. This is useful when fog
appears on the windshield or side glass due to rain or
snowy conditions.

3-8
Function Buttons
These buttons control the climate control ON/OFF,
air intake, front defrost, rear defrost and the air
conditioning operation.
OFF: Press the OFF button to turn off the climate
control system. This is the only setting that fully
shuts off the fan. The digital display will show only the
outside temperature. You can still adjust the driver set
temperature, the passenger temperature offset and the
air intake mode while in OFF.
A/C (Air Conditioning): This button turns
the air conditioning compressor off or on under most
conditions. The light on the A/C button will come on
when the compressor is operating in either the automatic
or manual mode. The air conditioning does not operate
at temperatures below approximately 35
F to 40
F
(2
C to 4
C). The light on the A/C button will flash if
pressed when air conditioning is not available. The air
conditioning cools and dehumidifies the air coming into
the vehicle. The air conditioning cannot be turned off in
defrost and defog, as it helps to remove moisture from
the vehicle. It also helps to keep the windows clear.If the system is operating in the AUTO mode, turning
the air conditioning off will delete AUTO from the
digital display and show current mode and fan settings.
The AUTO button must be pressed to return to the
automatic mode operation.
The air conditioning may be forced off at high engine
speeds or high engine oil or coolant temperatures.
(Outside Air): Press this button to provide outside
air. The light on this air intake button will come on to
show when it is operating. When in the AUTO mode,
the system automatically selects outside air instead of
recirculate, as required, to control the temperature in the
vehicle. By pressing outside air, the system will lock
into the outside air mode. Any adjustment to the air
intake must then be made manually. Outside air should
be used when trying to defrost or defog windows to help
reduce moisture inside of the vehicle.

3-9
(Recirculate): Press this button to limit the
amount of outside air entering the vehicle. The light on
this air intake button will come on to show when it is
operating. Recirculate is helpful when you are trying to
cool the air quickly or trying to limit odors and dust
from entering the vehicle. When in the AUTO mode,
the system automatically selects recirculate to cool the
vehicle's temperature. By pressing this button, the
system will lock into the recirculated air mode.
Any adjustment to the air intake must then be made
manually. Recirculation is not available when using the
defrost or defog mode because outside air is needed to
reduce moisture inside of the vehicle.
Operating the system in the recirculation mode may
cause fogging of the vehicle's windows when the
weather is cold and damp. To clear the fog, switch the
system to either the defog or defrost mode and increase
the fan speed. To avoid re
-fogging of the windows,
operate the system in the outside air mode.
FRONT: Press the FRONT defrost button to
quickly remove fog or frost from the windshield.
This setting directs most of the airflow to the windshield
and a small amount toward the lower and side window
outlets. The light on the button will come on and the
digital display will show the defrost mode symbol and
fan speed when the front defrost mode is being used.
Pressing FRONT defrost again will return the system to
the last operating mode and the air intake mode will be
in outside air.
If the system is in front defrost when you shut the
engine off, it will restart in FRONT defrost unless the
engine is off for longer than 40 minutes. If the engine is
off longer than 40 minutes, the system will restart in the
operating mode you had set prior to FRONT defrost and
the air intake mode will be in outside air.
See ªRear Window Defoggerº later in this section for
more information.

3-10 Sensors
The automatic electronic dual climate control system
uses several sensors to control operation and
display information.
Solar Load Sensor
This sensor is located on the top right side of the
defroster grille. The defroster grille is on the top of
the instrument panel.
The sensor monitors the sun's solar radiation and uses
this information as part of the automatic climate control
system when operating in the AUTO mode.
Be careful not to put anything over the sensor. When
covered, the sensor cannot compensate for changes in
the amount of heat the vehicle is absorbing from the sun.
Outside Air Temperature Sensor
This sensor is located in the air intake under the front
bumper of the vehicle. Information from this sensor is
used for the outside air temperature readings shown on the
digital display for the automatic climate control system.If the outside temperature goes up, the displayed
temperature will not change until:

The vehicle's speed is above 16 mph (26 km/h) for
one and a half minutes.

The vehicle's speed is above 45 mph (72 km/h) for
one minute.
These delays help prevent false readings. If the
temperature goes down, the outside temperature
display is updated immediately.
If the vehicle has been turned off for more than three
hours, the current outside temperature will be shown
when you start the vehicle. If it has been turned off for
less than three hours, the temperature will be recalled
from the previous vehicle operation.
Inside Temperature Sensor
This sensor is located to the left of the ignition switch.
The automatic climate control system uses this sensor
to receive information, so if you block or cover it,
the system will not function properly.

3-14 AM-FM Stereo with Cassette Tape Player
and Automatic Tone Control (If Equipped)
Your vehicle is equipped with six Bose
amplified
speakers. See your dealer for details.
Playing the Radio
PWR (Power): Press this knob to turn the system on
and off.
VOL (Volume): Turn the knob clockwise to increase
volume. Turn it counterclockwise to decrease volume.RECALL: Pressing this knob will display the station
being played or it will display the clock. Clock display
is available with the ignition turned off.
SCV (Speed
-Compensated Volume): With SCV,
your audio system adjusts automatically to make up for
road and wind noise as you drive. Set the volume at the
desired level. Turn the control ring behind the upper
knob clockwise to adjust the SCV. Each notch on the
control ring allows for more volume compensation
at faster vehicle speeds. Then, as you drive, SCV
automatically increases the volume, as necessary, to
overcome noise at any speed. The volume level should
always sound the same to you as you drive. If you don't
want to use SCV, turn the control all the way down.
Finding a Station
AM FM: Press this button to switch between AM,
FM1 and FM2. The display shows your selection.
TUNE: Press this knob lightly so it extends. Turn it to
choose radio stations. Push the knob back into its stored
position when you're not using it.

3-15
SEEK: Press the right or left arrow to go to the next
or previous station. The radio will seek to stations with
a strong signal only. The sound will mute while seeking.
To scan stations, press one of the SEEK arrows for
two seconds. SCAN will appear in the display. The radio
will go to a station, play for a few seconds, then go on to
the next station. Press SEEK again to stop scanning.
The radio will scan to stations with a strong signal only.
The sound will mute while scanning.
P.SCAN (Preset Scan): Press this button to scan preset
stations. The radio will go to the first preset station, play
for a few seconds and flash the stations frequency, then
go on to the next preset station. The AUTO TONE
setting stored for that pushbutton will be automatically
chosen. Press P.SCAN or one of the pushbuttons again
to stop scanning. P.SCAN will be displayed whenever
the tuner is in preset scan mode. The channel number
(P1 through P6) will appear momentarily just before the
frequency is displayed. In FM mode, this function will
scan through both FM1 and FM2 preset stations and
FM1 or FM2 will appear on the display. The radio will
scan preset stations with a strong signal only. The sound
will mute while scanning.Setting Preset Stations
The six numbered pushbuttons let you return to
your favorite stations. You can set up to 18 stations
(six AM, six FM1 and six FM2) by performing the
following steps:
1. Turn the radio on.
2. Press AM FM to select AM, FM1 or FM2.
3. Tune in the desired station.
4. Press AUTO TONE to select the equalization that
best suits the type of station selected.
5. Press and hold one of the six numbered pushbuttons.
The sound will mute. When it returns, release the
pushbutton. Whenever you press that numbered
pushbutton, the station you set will return and the
AUTO TONE equalization that you selected will
also be automatically selected for that button.
6. Repeat the steps for each pushbutton.

3-16
Setting the Tone (Bass/Treble)
BASS: To adjust the bass, press this knob lightly so it
extends. Turn the knob clockwise to increase bass and
counterclockwise to decrease bass.
TREB (Treble): To adjust the treble, press this knob
lightly so it extends. Turn the knob clockwise to
increase treble and counterclockwise to decrease treble.
If a station is weak or noisy, you may want to decrease
the treble.
Push these knobs back into their stored positions when
you're not using them.
AUTO TONE: This feature allows you to choose
bass and treble equalization settings designed
for country/western, jazz, talk, pop, rock and
classical stations.
Each time you press the AUTO TONE button, this
feature will switch to one of these program types.
To return the bass and treble to the manual mode,
either press and release the AUTO TONE button until
the display goes blank or press and release the BASS
and TREB knob and turn it until the display goes blank.Adjusting the Speakers (Balance/Fade)
BAL (Balance): To adjust the balance between the right
and left speakers, press this knob lightly so it extends.
Turn the knob clockwise for the right speakers and
counterclockwise for the left speakers. The middle
position balances the sound between the speakers.
FADE: To adjust the fade between the front and rear
speakers, press this knob lightly so it extends. Turn the
knob clockwise to adjust the sound to the front speakers
and counterclockwise for the rear speakers. The middle
position balances the sound between the speakers.
Push these knobs back into their stored positions when
you're not using them.
Playing a Cassette Tape
Your tape player is built to work best with tapes that are
up to 30 to 45 minutes long on each side. Tapes longer
than that are so thin they may not work well in this
player. If a tape is inserted when the ignition is on but
the radio is off, the tape will begin playing. A tape
symbol is shown in the center of the graphic display
whenever a tape is inserted. When a tape is active, the
tape symbol will be accompanied by a direction arrow.

3-17
While the tape is playing, use the VOL, AUTO TONE,
BAL, FADE, BASS and TREB controls just as you
do for the radio. Other controls may have different
functions when a tape is inserted. The display will show
the tape symbol and an arrow to show which side of the
tape is playing.
If you hear nothing or hear just a garbled sound, it may
not be in squarely. Press EJECT to remove the tape and
start over.
The player is able to detect a tight or broken tape, and
will eject the tape. The radio will go back to playing the
last station selected.
The player automatically senses the cassette for metal or
CrO
2 and sets the pre-emphasis. Anytime a tape is
inserted, the top side is selected to play first.
If an error appears on the display, see ªCassette Tape
Messagesº later in this section.
1 PREV (Previous): Press this pushbutton to go to
the previous selection on the tape if the current selection
has been playing for less than eight seconds. If this
pushbutton is pressed and the current selection has been
playing for more than eight seconds, it will go to the
beginning of the current selection. Your tape must have at least three seconds of silence between each selection
for previous or seek to work. The tape direction arrow
blinks and the sound will mute during previous or
seek operation.
2 PROG (Program): Press this pushbutton to play
the other side of the tape.
3 NEXT: Press this pushbutton or to go to the next
selection on the tape. If you hold this pushbutton or
press it more than once, the player will continue moving
forward through the tape. Your tape must have at least
three seconds of silence between each selection for next
to work. The tape direction arrow blinks and the sound
will mute during next or seek operation.
4 REV (Reverse): Press this pushbutton to reverse the
tape rapidly. Press it again to return to playing speed.
The radio will play the last selected station while the
tape reverses.

5 (Dolby): Press this pushbutton to reduce
background noise. The double
-D symbol will appear
on the display.
Dolby Noise Reduction is manufactured under a
license from Dolby Laboratories Licensing Corporation.
Dolby and the double
-D symbol are trademarks of
Dolby Laboratories Licensing Corporation.

3-18
FWD 6 (Forward): Press this pushbutton to advance
quickly to another part of the tape. Press it again to
return to playing speed. The radio will play the last
selected station while the tape advances.
SEEK: Press the right or left arrow to go to the
next or previous selection on the tape. Your tape must
have at least three seconds of silence between each
selection for seek to work.
AM FM: Press this button to listen to the radio when
a tape is playing.
TAPE AUX (Auxiliary): Press this button to play
a cassette tape when listening to the radio. The tape
symbol with an arrow will appear on the display when
the tape is active. If your system is equipped with a
remote playback device, pressing this button a second
time will allow the remote device to play.
EJECT: Press this button to remove the tape. The radio
will play. EJECT may be used with the ignition or radio
off. Cassettes may be loaded with the radio off if this
button is pressed first. If you leave a cassette tape in the
player while listening to the radio, it may become warm.Cassette Tape Messages
CLN (Clean): If this message appears on the display,
the cassette tape player needs to be cleaned. It will still
play tapes, but you should clean it as soon as possible to
prevent damage to the tapes and player. See ªCare of
Your Cassette Tape Playerº in the Index.
CD Adapter Kits
It is possible to use a portable CD player adapter kit
with your cassette tape player after activating the bypass
feature on your tape player.
To activate the bypass feature, use the following steps:
1. Turn the ignition to ACC or ON.
2. Turn the radio off.
3. Press and hold the TAPE AUX button for five
seconds. The tape symbol on the display will flash
for two seconds, indicating the feature is active.
4. Insert the adapter into the cassette slot. It will
power up the radio and begin playing.
This override routine will remain active until EJECT
is pressed.