CHEVROLET TRACKER 2001 2.G Owners Manual

2-75 Oil Pressure Light
If you have a problem
with your oil, this light may
stay on after you start your
engine, or come on when
you are driving.
This indicates that there is not enough pressure to keep
your engine properly lubricated and cool. The engine
could be low on oil, or have some other oil related
problem. Have it fixed right away.
The oil light could also come on in three other situations.

When the ignition is on but the engine is not running,
the light will come on as a test to show you it is
working, but the light will go out when you turn
the engine to START. If it doesn't come on with
the ignition on, you may have a problem with the
fuse or bulb. Have it fixed right away.

Sometimes when the engine is idling at a stop, the
light may blink on and off. This is normal.

If you make a hard stop, the light may come on
for a moment. This is normal.CAUTION:
Don't keep driving if the oil pressure is low.
If you do, your engine can become so hot that
it catches fire. You or others could be burned.
Check your oil as soon as possible and have your
vehicle serviced.
NOTICE:
Damage to your engine from neglected oil
problems can be costly and is not covered by
your warranty.

2-76 Four-Wheel-Drive Light (If Equipped)
This light comes on when
the ignition switch is on
and the transfer case lever
is in one of the four
-wheel
drive positions.
See ªFour
-Wheel Driveº in the Index.
Power Indicator Light (If Equipped)
This light comes on when
the power mode selector
switch is turned to ªPº
(power) with the ignition
switch in the ON position.
This light comes on as a check for approximately
five seconds when the ignition key is turned to ON
or START.
Overdrive Off Light (If Equipped)
This light comes on when
the automatic four
-speed
transmission has been
converted to the three
-speed
mode and the overdrive is
turned off.
This light also comes on as a check for approximately
five seconds when the ignition key is turned to ON
or START.

2-77 Fuel Gage
Your fuel gage shows about
how much fuel is in your
tank. When the gage first
indicates ªEº (empty), you
still have about one or two
gallons (4 to 8 L) of fuel left
in your tank, but you need
to get more right away.Here are four concerns some owners have had about the
fuel gage. All these situations are normal and do not
indicate that anything is wrong with the fuel gage.

At the gas station, the fuel pump shuts off before the
gage reads ªFº (full).

It takes more (or less) fuel to fill up than the gage
reads. For example, the gage reads half full, but it
took more (or less) than half of the tank's capacity
to fill it.

The gage moves a little when you turn, stop or
speed up.

When you turn the engine off, the gage doesn't go
back to E (empty).

3-
3-1
Section 3 Comfort Controls and Audio Systems
In this section, you'll find out how to operate the comfort control and audio systems offered with your vehicle. Be
sure to read about the particular systems supplied with your vehicle.
3
-2 Comfort Controls
3
-2 Climate Control System
3
-3 Air Conditioner Controls
3
-4 Heating
3
-4 Defogging and Defrosting
3
-4 Rear Window Defogger (If Equipped)
3
-5 Ventilation System
3
-6 Audio Systems
3
-6 Setting the Clock
3
-6AM-FM Stereo3
-9AM-FM Stereo with Cassette Tape Player
3
-14 AM-FM Stereo with Compact Disc Player
(If Equipped)
3
-18 Understanding Radio Reception
3
-18 Tips About Your Audio System
3
-19 Care of Your Cassette Tape Player
3
-21 Care of Your Compact Discs
3
-21 Care of Your Compact Disc Player
3
-21 Antenna

3-2
Comfort Controls
With this system, you can control the heating and
ventilation in your vehicle. Your vehicle's air
conditioning can also control cooling.
Your vehicle also has the flow
-through ventilation
system described later in this section.
Climate Control System
Airflow Lever
VENT: This position directs the airflow through
the instrument panel vents.
BI-LEVEL: This position directs air through the
instrument panel vents and toward the floor.
FLOOR: This position directs air toward the floor.
DEFOG: This position directs air toward the
floor, the windshield and side windows. The air also
comes from both vents at the ends of the instrument
panel if the thumbwheel below them is in the open
position. The air conditioning compressor will run
automatically in this setting without turning on the
A/C button light.
DEFROST: This position directs air to the
windshield and side windows. The air also comes from
both vents at the ends of the instrument panel if the
thumbwheel below them is in the open position. The air
conditioning compressor will run automatically in this
setting without turning on the A/C button light. For
maximum defrosting, adjust the temperature control
lever to the hot end and adjust the side outlets so the air
blows on the side window.

3-3
Fan Lever
Slide the lever away from OFF to turn the system on.
Move the lever toward the fan symbol to increase the
fan's speed.
Temperature Lever
Slide the lever to change the temperature of the air
flowing from the system. Move it to the right for
warmer air and to the left for cooler air. Without air
conditioning, the air temperature cannot be less than
the outside air temperature.
Air Intake Lever
RECIRCULATE: Choose this position to
recirculate the inside air through the comfort
control system.
OUTSIDE AIR: Choose this position to circulate
outside air through the comfort control system.
Air Conditioner Controls
The air conditioning system
uses the same controls as
described previously. The
function of each lever is
explained under ªClimate
Control Systemº in this
part. The incoming air is
cooled and dehumidified
instead of being heated.
Push the A/C button to change your comfort control
system from heating to air conditioning. With this
operation, a light will come on when the air
conditioning is on. The A/C button can also control
the humidity in your vehicle.
The air conditioner works best if you keep your
windows closed. On very hot days, open the windows
just long enough for the hot air to escape.

3-4
For normal cooling, push the A/C button and move the
air intake lever to OUTSIDE AIR. For faster cooling,
move the lever to RECIRCULATE. Then move the
airflow lever to VENT, the temperature lever toward the
left and the fan lever toward the fan symbol.
On days when it is raining or the humidity is high,
follow these dehumidifying steps to help clean windows
that are cloudy with moisture. Move the air intake lever
to OUTSIDE AIR. Move the airflow lever to DEFROST
and the fan lever toward the fan symbol. Adjust the
temperature lever to a comfortable setting. The air
conditioning compressor will run automatically and the
A/C button will illuminate when the air flow lever is in
DEFOG or DEFROST.
Heating
For the quickest results, move the air intake lever to
RECIRCULATE. Move the airflow lever to FLOOR,
the temperature lever toward the right for warmer air
and the fan lever toward the fan symbol. You should
switch to OUTSIDE AIR once in a while to avoid stale
air and cloudy windows.
Defogging and Defrosting
Slide the air intake lever to OUTSIDE AIR and
the airflow lever to DEFROST to direct air to the
windshield vents. Then slide the temperature lever
toward the right and the fan lever toward the fan
symbol. When the windshield is clear, turn down
the fan speed.
Rear Window Defogger (If Equipped)
The rear window defogger
uses a warming grid to
remove fog from the
rear window.
Press the switch to turn on the defogger. An indicator
light on the switch will come on to remind you that the
defogger is on. The rear window defogger will turn
itself off after about 15 minutes. You can also turn it off
by pressing the switch again.

3-5
Do not attach anything like a temporary vehicle license
or a decal across the defogger grid on the rear window.
NOTICE:
Don't use a razor blade or something else sharp
on the inside of the rear window. If you do, you
could cut or damage the warming grid, and the
repairs wouldn't be covered by your warranty.
Ventilation System
For mild outside temperatures, when little heating or
cooling is needed, you can still direct outside air through
your vehicle.
Move the air intake lever to OUTSIDE AIR and the
airflow lever to BI
-LEVEL. Adjust the temperature
control lever to a comfortable setting and move the fan
control lever toward the fan symbol.
Your vehicle's flow
-through ventilation system supplies
outside air into the vehicle when it is moving. Outside
air will also enter the vehicle when the fan is running
and the air intake lever is at OUTSIDE AIR.
Your vehicle has air outlets
that allow you to adjust the
direction and amount of
airflow inside the vehicle.
You can direct the airflow side
-to-side by turning the
thumbwheel located in the center of the vent. The vent
can be tilted up and down also. To control the amount of
airflow though the outlets, turn the thumbwheel below
the vent. The airflow from this vent cannot be controlled
by the airflow lever.

3-6
Ventilation Tips
Keep the hood and front air inlet free of ice, snow or
any other obstruction (such as leaves). The heater and
defroster will work far better, reducing the chance of
fogging the inside of your windows.
When you enter a vehicle in cold weather, move the fan
control lever toward the fan symbol for a few moments
before driving off. This helps clear the intake ducts of
snow and moisture, and reduces the chance of fogging
the inside of your windows.
Keep the air path under the front seats clear of objects.
This helps air to circulate throughout your vehicle.
Audio Systems
Your audio system has been designed to operate easily
and give years of listening pleasure. You will get the
most enjoyment out of it if you acquaint yourself with it
first. Find out what your audio system can do and how
to operate all its controls, to be sure you're getting the
most out of the advanced engineering that went into it.
Setting the Clock
Press and hold the HR or MIN arrow for two seconds.
Then press the HR arrow until the correct hour appears.
Press and hold the MIN arrow until the correct minute
appears. The clock may be set with the ignition on
or off.
AM-FM Stereo
Playing the Radio
PWR VOL: Press this knob to turn the system on and
off. To increase volume, turn the knob clockwise. Turn
it counterclockwise to decrease volume.
RCL: Press this knob to recall the station being played
or to display the clock. Clock display is available with
the vehicle off.
Finding a Station
AM FM: Press this button to switch between AM, FM1
and FM2. The display shows your selection.
TUNE: Turn this knob to choose radio stations.

3-7
SEEK: Press the right arrow to tune to the next higher
station and the left arrow to tune to the next lower
station and stay there. The radio will seek to stations
with a strong signal only.
SCAN: Press and hold one of the SEEK arrows for two
seconds until you hear a beep. Use SCAN to listen to
stations for a few seconds. The radio will go to a station,
stop for a few seconds and flash the station frequency,
then go on to the next station. Press one of the SEEK
arrows again to stop scanning. The radio will scan to
stations with a strong signal only.
PRESET SCAN: Use preset scan to listen to each of
your preset stations for a few seconds. Press and hold
one of the SEEK arrows for more than four seconds
until you hear two beeps. The radio will go to the first
preset station stored on your pushbuttons, except those
stations with weak reception, stop for a few seconds and
flash the station frequency, then go on to the next preset
station. Preset scan will only scan the six presets that are
in the band selected. Press one of the SEEK arrows
again to stop scanning presets. The channel number
(P1 through P6) will appear momentarily just before the
frequency is displayed.PUSHBUTTONS: The six numbered pushbuttons let
you return to your favorite stations. You can set up to
18 stations (six AM, six FM1 and six FM2) by
performing the following steps:
1. Turn the radio on.
2. Press AM FM to select the band.
3. Tune in the desired station.
4. Press and hold one of the six numbered buttons until
you hear a beep. Whenever you press that numbered
button, the station you set will return.
5. Repeat the steps for each pushbutton.
Setting the Tone
BASS: Press and release AUDIO repeatedly until BAS
appears on the display. Then press and hold the up arrow
to increase bass. ªBº and a positive number will appear
on the display. Press and hold the down arrow to
decrease bass. B and a negative number will appear on
the display. B and a zero will appear on the display
when the bass level is set to the middle position.
Release the up or down arrow when you find the bass
level you want or when the maximum or minimum level
is reached.