CHRYSLER SEBRING SEDAN 2010 3.G Owners Manual

Installation
Align the liner in the cupholder and press down firmly.
FUSES
Totally Integrated Power Module (TIPM)
The TIPM is located in the engine compartment near the
air cleaner assembly. This center contains cartridge fuses
and mini fuses. A label that identifies each component
may be printed on the inside of the cover. Refer to the
graphic below for FUSES/TIPM location.
Totally Integrated Power Module (TIPM)
7
MAINTAINING YOUR VEHICLE 371

CavityCartridge
Fuse Mini
Fuse Description
1 40 Amp
Green —Power Top Module
(If Equipped)
2— 20 Amp
Yellow AWD Module
3— 10 Amp
Red Battery Feed —
Center High
Mounted Stop
Light (CHMSL)/
Brake Switch
4— 10 Amp
Red Battery Feed — Ig-
nition Switch
5— 20 Amp
Yellow Trailer Tow — If
Equipped
6— 10 Amp
Red Ignition Off Draw
(IOD) — Power
Mirror Switch/
Climate ControlsCavity
Cartridge
Fuse Mini
Fuse Description
7— 30 Amp
Green Ignition Off Draw
(IOD) Sense 1
8— 30 Amp
Green Ignition Off Draw
(IOD) Sense 2
9 40 Amp
Green Battery Feed —
Power Seats - if
equipped/PZEV
Air Pump - if
equipped
10 —20 Amp
Yellow Battery Feed —
Cabin Compart-
ment Node (CCN)
11 —15 Amp
Lt Blue Selectable Power
Outlet
12 —20 Amp
Yellow —
372 MAINTAINING YOUR VEHICLE

CavityCartridge
Fuse Mini
Fuse Description
13 —20 Amp
Yellow —
14 —10 Amp
Red Ignition Off Draw
(IOD) — Cabin
Compartment Node
(CCN)/ Interior
Lighting
15 40 Amp
Green —Battery Feed — Ra-
diator Fan Relay
16 —15 Amp
Lt. Blue IGN Run/ACC —
Cigar Lighter/PWR
Sunroof ModCavity
Cartridge
Fuse Mini
Fuse Description
17 —10 Amp
Red Ignition Off Draw
(IOD) — Wireless
Control Module
(WCM)/Clock/
Steering Control
Module (SCM)
18 40 Amp
Green —Battery Feed —
Auto Shutdown
(ASD) Relay
19 —20 Amp
Yellow Ignition Off Draw
(IOD) — Power
AmpFeed2-if
equipped
20 —15 Amp
Lt. Blue Ignition Off Draw
(IOD) — Radio
21 —10 Amp
Red —
7
MAINTAINING YOUR VEHICLE 373

CavityCartridge
Fuse Mini
Fuse Description
22 —10 Amp
Red Ignition Run — Cli-
mate Controls/Hot
Cupholder - if
equipped
23 —15 Amp
Lt. Blue Auto Shutdown
(ASD) Relay Feed 3
24 —25 Amp
Natural Battery Feed —
PWR Sunroof Feed
25 —10 Amp
Red Ignition Run —
Heated Mirrors - If
Equipped
26 —15 Amp
Lt. Blue Auto Shutdown
(ASD) Relay Feed 2Cavity
Cartridge
Fuse Mini
Fuse Description
27 —10 Amp
Red Ignition Run — Oc-
cupant Classifica-
tion Module
(OCM)/Occupant
Restraint Controller
(ORC)
28 —10 Amp
Red Ignition Run — Oc-
cupant Classifica-
tion Module
(OCM)/Occupant
Restraint Controller
(ORC)
29 — — Hot Car (No Fuse
Required)
30 —20 Amp
Yellow Ignition Run —
Heated Seats - If
Equipped
374 MAINTAINING YOUR VEHICLE

CavityCartridge
Fuse Mini
Fuse Description
31 —10 Amp
Red —
32 30 Amp
Pink —Auto Shutdown
(ASD) Relay Feed 1
33 —10 Amp
Red Battery Feed —
Switch Bank/
Diagnostic Link
Connector/
Powertrain Control
Module (PCM)
34 30 Amp
Pink —Battery Feed —
Anti-Lock Brakes
(ABS) Module - if
equipped/
Electronic Stability
Program (ESP)
Module - If
EquippedCavity
Cartridge
Fuse Mini
Fuse Description
35 40 Amp
Green —Battery Feed —
Anti-Lock Brakes
(ABS) Module - If
Equipped/
Electronic Stability
Program (ESP)
Module - If
Equipped
7
MAINTAINING YOUR VEHICLE 375

CavityCartridge
Fuse Mini
Fuse Description
36 30 Amp
Pink —Battery Feed —
Passenger Door
Module (PDM)/
Driver Door Mod-
ule (DDM)
37 —25 Amp
Natural Power Top Module
(If Equipped)
CAUTION!
•When installing the Totally Integrated Power
Module cover, it is important to ensure the cover is
properly positioned and fully latched. Failure to
do so may allow water to get into the Totally
Integrated Power Module, and possibly result in
an electrical system failure.
(Continued)
CAUTION! (Continued)
•When replacing a blown fuse, it is important to
use only a fuse having the correct amperage rating.
The use of a fuse with a rating other than indicated
may result in a dangerous electrical system over-
load. If a properly rated fuse continues to blow, it
indicates a problem in the circuit that must be
corrected.
VEHICLE STORAGE
If you will not be using your vehicle for more than
21 days, you may want to take steps to preserve your
battery.
•Disengage the mini-fuse in the Power Distribution
Center labeled IOD (Ignition Off-Draw).
•Disconnect the negative cable from the battery.
376 MAINTAINING YOUR VEHICLE

REPLACEMENT BULBS
All the inside bulbs are brass or glass wedge base.
Aluminum base bulbs are not approved and should not
be used for replacement.
LIGHT BULBS — Interior Bulb No.
Front Courtesy/Reading Lamp..........578/W5W
Center Courtesy/Reading Lamp ..........578/W5W
Visor Vanity Lamp ...................... A6220
Glove Box Lamp ....................... A6220
Shift Indicator Lamp ................. IKLE14140
Rear Compartment (Trunk) Lamp ............. 579
NOTE: For lighted switches, see your authorized dealer
for replacement.
LIGHT BULBS — Exterior Bulb No.
Low Beam Headlamp ..................... H11
High Beam Headlamp .................... 9005Front Park/Turn Signal/Side Marker Lamp
....3757A
Front Fog Lamp ...................... PSX24W
Center High Mounted Stop (CHMSL)
Lamp ........................... W16W (921)
Rear Tail/Stop Lamp ..................... 3157
Rear Turn Signal Lamp .................... 3157
Backup Lamp .......................... 3157
License Lamp .......................... W5W
Front Position Lamp ..................... W5W
BULB REPLACEMENT
Headlamp
1. Raise and prop open the hood. Locate the connector
behind the headlamp.
NOTE:It may be necessary to remove the air cleaner
filter housing and position the totally integrated power
module aside prior to replacing the low beam headlamp
on the driver’s side of the vehicle.7
MAINTAINING YOUR VEHICLE 377

2. Reach into engine compartment and from behind the
lamp assembly and grasp the connector.3. Rotate bulb and connector one-quarter turn and pull
outward from assembly.
CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life.
378 MAINTAINING YOUR VEHICLE

4. Pull the bulb out of the socket and replace the bulb.
5. If the bulb comes in contact with any oily surface,
clean the bulb with rubbing alcohol.
6. Reinsert the bulb and socket assembly and rotate
clockwise one-quarter turn to secure.Front Turn Signal/Parking Lamp
1. Raise and prop open the hood.
2. Rotate the bulb’s electrical connector one-quarter turn
counterclockwise and remove it from the headlamp
housing.
7
MAINTAINING YOUR VEHICLE 379

3. Remove the bulb from the connector socket and install
the replacement bulb.
4. Install the bulb and connector assembly into the
headlamp housing and rotate the connector one-quarter
turn clockwise to lock it in place.
Front Fog Lamp
NOTE:Access to the lamps through the lower fascia
cutout is limited. We recommend you access the lamps by
turning the steering wheel to allow access and remove
the inner fender shield.
1. Rotate the bulb’s electrical connector one-quarter turn
counterclockwise and remove it from the fog lamp hous-
ing. 2. Remove the bulb from the connector socket and install
the replacement bulb.
380 MAINTAINING YOUR VEHICLE