relay CHRYSLER VOYAGER 2000 Diagnostic Manual

Symptom:
* CHECKING CHARGING SYSTEM OPERATION WITH NO DTC'S
POSSIBLE CAUSES
TROUBLE CODES PRESENT
VOLTAGE DIFFERENCE >= 1 VOLT
GENERATOR FIELD TERMINAL INTERMITTENT DEFECTIVE
GENERATOR GROUND CIRCUIT HIGH RESISTANCE
B+ CIRCUIT HIGH RESISTANCE (0.4 VOLT)
B+ CIRCUIT HIGH RESISTANCE (1 VOLT)
PCM DEFECTIVE (CHARGING SYSTEM NO CODE)
GENERATOR BELT VISIBLY DEFECTIVE
TROUBLE CODES PRESENT 1600 RPM
TEST ACTION APPLICABILITY
1Note: Battery condition must be verified prior to this test.
Inspect the Generator Belt tension and condition.
Is the Generator Belt in good condition?All
Ye s®Go To 2
No®Repair as necessary.
Perform Powertrain Verification Test VER-3A.
2 Engine Running
With the DRB, set engine speed to 1600 RPM for 30 seconds.
With the DRB, return the engine to idle speed and read codes.
Are there any Charging System trouble codes?All
Ye s®Refer to Symptom List for problems related to Charging.
Perform Powertrain Verification Test VER-3A.
No®Go To 3
3 Turn ignition on. (Engine off)
With the DRB, actuate the Generator field.
Using a Voltmeter, backprobe Generator Field Driver Terminal at the back of
Generator.
Note: The voltage should cycle from 7.2 volts to Battery voltage every 1.4
seconds, at both Terminals.
While monitoring the Voltmeter, wiggle the field Terminals back to the PCM and ASD
Relay.
Was there any interruption in the normal cycle between 7.2 volts and Battery
voltage?All
Ye s®Repair the Wire where wiggling interrupted the voltage cycle.
Perform Powertrain Verification Test VER-3A.
No®Go To 4
24
CHARGING
ProCarManuals.com

Symptom:
P-0123 THROTTLE POSITION SENSOR VOLTAGE HIGH
When Monitored and Set Condition:
P-0123 THROTTLE POSITION SENSOR VOLTAGE HIGH
When Monitored: With the ignition on.
Set Condition: TP sensor signal voltage goes above 4.5 volts for .704 seconds.
POSSIBLE CAUSES
THROTTLE POSITION SENSOR GROUND CIRCUIT OPEN
THROTTLE POSITION SENSOR SIGNAL CIRCUIT OPEN
TPS SIGNAL CKT TO TPS 5 VOLT SUPPLY CKT SHORTED
TPS WIRING HARNESS INTERMITTENT DEFECT
TPS WIRING HARNESS OBSERVABLE DEFECT
POWERTRAIN CONTROL MODULE DEFECTIVE (TPS)
THROTTLE POSITION SENSOR VOLTAGE BELOW 1.0 VOLT
THROTTLE POSITION SENSOR VOLTAGE CHANGE NOT SMOOTH
TEST ACTION APPLICABILITY
1 Ignition On, Engine Not Running
Using the DRB, read the Throttle Position Sensor voltage.
Is the Throttle Position Sensor voltage above 4.5 volts?All
Ye s®Go To 2
No®Go To 8
2 Ignition Off
Disconnect the Throttle Position Sensor Connector.
Note: Check connectors - Clean/repair as necessary.
Ignition On.
With the DRB actuate the ASD relay.
Measure the voltage of the TP sensor signal circuit.
Is the voltage above 4.9 volts?All
Ye s®Repair the short voltage in the Throttle Position Sensor Signal
Circuit.
Perform Powertrain Verification Test VER-5A.
No®Go To 3
48
DRIVEABILITY
ProCarManuals.com

Symptom:
P-0135 O2S HEATER FAILURE
When Monitored and Set Condition:
P-0135 O2S HEATER FAILURE
When Monitored: With the ignition key off, after the engine cools down.
Set Condition: No sensor output signal is received when the PCM powers up the sensor
heater.
POSSIBLE CAUSES
1/1 O2 SENSOR CONNECTOR DAMAGED
1/1 O2 SENSOR GND CIRCUIT OPEN
ASD RELAY OUTPUT CIRCUIT OPEN
1/1 O2 SENSOR FAILURE
1/1 O2 SENSOR HEATER ELEMENT FAILURE
1/1 O2S HEATER FAILURE DOES NOT REOCCUR
TEST ACTION APPLICABILITY
1 With the DRB, read the DTCs.
Is the GLOBAL GOOD TRIP counter displayed and equal to zero?All
Ye s®Go To 2
No®Go To 3
2 Turn Ignition On (Engine Off), wait three minutes.
With the DRB , monitor the O2 Sensor voltage for a few minutes until the voltage
stabilizes between .4 and .6 volts.
With the DRB, actuate the O2 Heater Test.
Monitor O2 voltage for up to two minutes.
Is the O2 Sensor voltage still between .4 and .6 volts?All
Ye s®Go To 4
No®Go To 3
3 At this time the 1/1 O2S HEATER FAILURE does not exist or is an intermittent
problem.
With the DRB, read the FREEZE FRAME DATA.
With this screen, attempt to duplicate the condition that has set this fault.
While using FREEZE FRAME DATA pay particular attention to the fault setting
conditions, such as speed, temp, load, and map vacuum.
Does the 1/1 O2S HEATER FAILURE reoccur?All
Ye s®Go To 4
No®1/1 O2S Heater failure no longer exists.
Perform VERIFICATION TEST VER-5A3.
62
DRIVEABILITY
ProCarManuals.com

TEST ACTION APPLICABILITY
4 Disconnect the 1/1 O2 Sensor Connector.
Check connectors - Clean / repair as necessary.
Is any terminal corroded, damaged, pushed out or miswired?All
Ye s®Repair or replace as necessary.
Perform VERIFICATION TEST VER-5A3.
No®Go To 5
5 Turn Ignition On (Engine Off).
Disconnect the 1/1 O2 Sensor Connector.
Check connectors - Clean / repair as necessary.
With the DRB, actuate the ASD Relay.
Using a voltmeter, measure the ASD Relay Output Circuit at the O2 Sensor
Connector (harness side).
Is the voltage above 10.0 volts?All
Ye s®Go To 6
No®Repair the open ASD Relay Output Circuit.
Perform VERIFICATION TEST VER-5A3.
6 Disconnect the 1/1 O2 Sensor Connector.
Check connectors - Clean / repair as necessary.
Using an ohmmeter, measure the O2 Sensor Heater Element at the O2 Sensor
Connector (component side).
Is the resistance between 4 and 7 ohms?All
Ye s®Go To 7
No®Replace the 1/1 O2 Sensor.
Perform VERIFICATION TEST VER-5A3.
7 Disconnect the 1/1 O2 Sensor Connector.
Check connectors - Clean / repair as necessary.
Using an ohmmeter, measure from the Heater Ground Circuit to ground at the O2
Sensor Connector (harness side).
Is the resistance below 5.0 ohms?All
Ye s®Replace the 1/1 O2 Sensor.
Perform VERIFICATION TEST VER-5A3.
No®Repair the open 1/1 O2 Sensor Ground Circuit.
Perform VERIFICATION TEST VER-5A3.
63
DRIVEABILITY
P-0135 O2S HEATER FAILURE ÐContinued
ProCarManuals.com

Symptom:
P-0141 1/2 O2S HEATER FAILURE
When Monitored and Set Condition:
P-0141 1/2 O2S HEATER FAILURE
When Monitored: With the ignition key off, after the engine cools down.
Set Condition: No sensor output signal is received when the PCM powers up the sensor
heater.
POSSIBLE CAUSES
1/2 O2 SENSOR CONNECTOR DAMAGED
1/2 O2 SENSOR GND CIRCUIT OPEN
ASD RELAY OUTPUT CIRCUIT OPEN
1/2 O2 SENSOR FAILURE
1/2 O2 SENSOR HEATER ELEMENT FAILURE
1/2 O2S HEATER FAILURE DOES NOT REOCCUR
TEST ACTION APPLICABILITY
1 With the DRB, read the DTCs.
Is the GLOBAL GOOD TRIP counter displayed and equal to zero?All
Ye s®Go To 2
No®Go To 3
2 Turn Ignition On (Engine Off), wait three minutes.
With the DRB, monitor the O2 Sensor voltage for a few minutes until the voltage
stabilizes between .4 and .6 volts.
With the DRB, actuate the O2 Heater test.
Monitor O2 voltage for up to two minutes.
Is the O2 Sensor voltage still between .4 and .6 volts?All
Ye s®Go To 3
No®Go To 4
3 At this time the 1/2 O2S HEATER FAILURE does not exist or is an intermittent
problem.
With the DRB, read the FREEZE FRAME DATA.
With this screen, attempt to duplicate the condition that has set this fault.
While using FREEZE FRAME DATA pay particular attention to the fault setting
conditions, such as speed, temp, load, and map vacuum.
Does the 1/2 O2S HEATER FAILURE reoccur?All
Ye s®Go To 4
No®1/2 O2S Heater failure no longer exists.
Perform VERIFICATION TEST VER-5A3.
73
DRIVEABILITY
ProCarManuals.com

TEST ACTION APPLICABILITY
4 Disconnect the 1/2 O2 Sensor Connector.
Check connectors - Clean / repair as necessary.
Is any terminal corroded, damaged, pushed out or miswired?All
Ye s®Repair or replace as necessary.
Perform VERIFICATION TEST VER-5A3.
No®Go To 5
5 Turn Ignition On (Engine Off).
Disconnect the 1/2 O2 Sensor Connector.
Check connectors - Clean / repair as necessary.
With the DRB, actuate the ASD Relay.
Using a voltmeter, measure the ASD Relay Output Circuit at the O2 Sensor
Connector (harness side).
Is the voltage above 10.0 volts?All
Ye s®Go To 6
No®Repair the open ASD Relay Output Circuit.
Perform VERIFICATION TEST VER-5A3.
6 Disconnect the 1/2 O2 Sensor Connector.
Check connectors - Clean / repair as necessary.
Using an ohmmeter, measure the O2 Sensor Heater Element at the O2 Sensor
Connector (component side).
Is the resistance between 4 and 7 ohms?All
Ye s®Go To 7
No®Replace the 1/2 O2 Sensor.
Perform VERIFICATION TEST VER-5A3.
7 Disconnect the 1/2 O2 Sensor Connector.
Check connectors - Clean / repair as necessary.
Using an ohmmeter, measure from the Heater Ground Circuit to ground at the O2
Sensor Connector (harness side).
Is the resistance below 5.0 ohms?All
Ye s®Replace the 1/2 O2 Sensor.
Perform VERIFICATION TEST VER-5A3.
No®Repair the open 1/2 O2 Sensor Ground Circuit.
Perform VERIFICATION TEST VER-5A3.
74
DRIVEABILITY
P-0141 1/2 O2S HEATER FAILURE ÐContinued
ProCarManuals.com

Symptom:start here
P-0201 INJECTOR #1 CONTROL CIRCUIT
When Monitored and Set Condition:
P-0201 INJECTOR #1 CONTROL CIRCUIT
When Monitored: With battery voltage greater than 12 volts, the auto shutdown relay
energized, injector pulse width less than 10ms, and engine speed less than 3000 rpm.
Set Condition: This trouble code takes .64 to 10.0 seconds to set when no inductive kick
is sensed .18ms after injector turn off, and with no other injectors on.
POSSIBLE CAUSES
ASD RELAY OUTPUT CIRCUIT OPEN
INJECTOR DEFECTIVE
INJECTOR #1 DRIVER CIRCUIT OPEN
INJECTOR #1 DRIVER CIRCUIT SHORTED TO GROUND
POWERTRAIN CONTROL MODULE DEFECTIVE
INJECTOR #1 DRIVER CIRCUIT SHORT TO GROUND
INJECTOR #1 DRIVER CIRCUIT SHORT TO GROUND (PCM)
TEST ACTION APPLICABILITY
1 Ignition Off
Start engine, let idle for at least 20 seconds.
Key on, engine off.
With the DRB, read Trouble Codes.
Is the Global Good Trip counter displayed and equal to zero?All
Ye s®Go To 2
No®Go To 7
2 Ignition Off
Disconnect the Injector #1 Connector.
Note: Check connectors - Clean/repair as necessary.
Using an Ohmmeter, measure resistance of Injector #1.
Is the resistance between 10.0 and 16.0 ohms?All
Ye s®Go To 3
No®Replace the Fuel Injector.
Perform Powertrain Verification Test VER-5A.
83
DRIVEABILITY
ProCarManuals.com

TEST ACTION APPLICABILITY
3 Ignition Off
Disconnect the Injector #1 Connector.
Note: Check connectors - Clean/repair as necessary.
Turn ignition on.
With the DRB, actuate the Auto Shutdown Relay.
Using a Voltmeter, measure the ASD Relay Output voltage.
Does the voltage cycle high and low?All
Ye s®Go To 4
No®Repair the open ASD Relay Output Circuit.
Perform Powertrain Verification Test VER-5A.
4 Ignition Off
Disconnect the Injector #1 Connector.
Note: Check connectors - Clean/repair as necessary.
Disconnect the Powertrain Control Module Connector.
Note: Check connectors - Clean/repair as necessary.
Use an Ohmmeter in the following step.
Measure the Injector #1 Driver Circuit from the PCM to the Injector.
Is the resistance below 5.0 ohms?All
Ye s®Go To 5
No®Repair the open Injector #1 Driver Circuit.
Perform Powertrain Verification Test VER-5A.
5 Ignition Off
Disconnect the Injector #1 Connector.
Note: Check connectors - Clean/repair as necessary.
Disconnect the Powertrain Control Module Connector.
Note: Check connectors - Clean/repair as necessary.
Using an Ohmmeter, measure the Injector #1 Driver Circuit.
Is the resistance below 5.0 ohms?All
Ye s®Repair the Injector #1 Driver Circuit for a short to ground.
Perform Powertrain Verification Test VER-5A.
No®Go To 6
6 If there are no potential causes remaining, the Powertrain Control Module is
assumed to be defective.
View repair options.All
Repair
Replace the Powertrain Control Module.
Perform Powertrain Verification Test VER-5A.
7 Ignition Off
Using the schematic as a guide, inspect the Wiring and Connectors.
Were any problems found?All
Ye s®Repair as necessary.
Perform Powertrain Verification Test VER-5A.
No®Go To 8
84
DRIVEABILITY
P-0201 INJECTOR #1 CONTROL CIRCUIT ÐContinued
ProCarManuals.com

Symptom:
P-0202 INJECTOR #2 CONTROL CIRCUIT
When Monitored and Set Condition:
P-0202 INJECTOR #2 CONTROL CIRCUIT
When Monitored: With battery voltage greater than 12 volts, the auto shutdown relay
energized, injector pulse width less than 10ms, and engine speed less than 3000 rpm.
Set Condition: This trouble code takes .64 to 10.0 seconds to set when no inductive kick
is sensed .18ms after injector turn off, and with no other injectors on.
POSSIBLE CAUSES
ASD RELAY OUTPUT CIRCUIT OPEN
INJECTOR DEFECTIVE
INJECTOR #2 DRIVER CIRCUIT OPEN
INJECTOR #2 DRIVER CIRCUIT SHORTED TO GROUND
PCM DEFECTIVE
TEST ACTION APPLICABILITY
1 Ignition Off
Start engine, let idle for at least 20 seconds.
Key on, engine off.
With the DRB, read Trouble Codes.
Is the Global Good Trip counter displayed and equal to zero?All
Ye s®Go To 2
No®Go To 7
2 Ignition Off
Note: It may be necessary to remove the Intake Plenum in the following
steps.
Disconnect the Injector #2 Connector.
Note: Check connectors - Clean/repair as necessary.
Using an Ohmmeter, measure resistance of Injector #2.
Is the resistance between 10.0 and 16.0 ohms?All
Ye s®Go To 3
No®Replace the Fuel Injector.
Perform Powertrain Verification Test VER-5A.
86
DRIVEABILITY
ProCarManuals.com

TEST ACTION APPLICABILITY
3Note: It may be necessary to remove the Intake Plenum in the following
steps.
Ignition Off
Disconnect the Injector #2 Connector.
Note: Check connectors - Clean/repair as necessary.
Turn ignition on.
With the DRB, actuate the Auto Shutdown Relay.
Using a Voltmeter, measure the ASD Relay Output Circuit voltage.
Does the voltage cycle high and low?All
Ye s®Go To 4
No®Repair the open ASD Relay Output Circuit.
Perform Powertrain Verification Test VER-5A.
4 Ignition Off
Disconnect the Injector #2 Connector.
Note: Check connectors - Clean/repair as necessary.
Disconnect the Powertrain Control Module Connector.
Note: Check connectors - Clean/repair as necessary.
Use an Ohmmeter in the following step.
Measure the Injector #2 Driver Circuit from the PCM to the Injector.
Is the resistance below 5.0 ohms?All
Ye s®Go To 5
No®Repair the open Injector #2 Driver Circuit.
Perform Powertrain Verification Test VER-5A.
5 Ignition Off
Disconnect the Injector #2 Connector.
Note: Check connectors - Clean/repair as necessary.
Disconnect the Powertrain Control Module Connector.
Note: Check Connectors - Clean/repair as necessary.
Using an Ohmmeter, measure the Injector #2 Driver Circuit to ground.
Is the resistance below 5.0 ohms?All
Ye s®Repair the Injector #2 Driver Circuit for a short to ground.
Perform Powertrain Verification Test VER-5A.
No®Go To 6
6 If there are no potential causes remaining, the Powertrain Control Module is
assumed to be defective.
View repair options.All
Repair
Replace the Powertrain Control Module.
Perform Powertrain Verification Test VER-5A.
7 Engine Running
Wiggle Wiring Harness from the Injector to the PCM.
Does the engine miss or stall?All
Ye s®Repair as necessary where wiggling caused the problem to
appear.
Perform Powertrain Verification Test VER-5A.
No®Go To 8
87
DRIVEABILITY
P-0202 INJECTOR #2 CONTROL CIRCUIT ÐContinued
ProCarManuals.com