headlamp Citroen BERLINGO DAG 2011 2.G Owner's Manual
Page 3 of 223
8
Interior
INSTRUMENTS AND CONTROLS
1. Lighting and direction indicator
stalk.
2. I n s t r u m e n t p a n e l w i t h s c r e e n .
3. Wipers, screenwash, trip
computer controls.
4. I g n i t i o n .
5. Audio equipment.
6. Driver's airbag, horn.
7. Steering wheel height and reach
adjustment.
8. Cruise control, speed limiter
switch.
9. Control panel, parking sensors,
headlamp beam adjustment,
ESP, Stop & Start.
10. Bonnet release.
11. Electric door mirror adjustment.
Page 6 of 223
3
3
7
3
11
1
FAMILIARISATION
Interior
Lighting off.
Sidelamps.
Main beam headlamps (blue).
Dipped beam headlamps (green).
2 fast.
1 normal.
I i n t e r m i t t e n t .
0 park.
single wipe.
AUTO, press the stalk down.
Reactivate if the ignition
has been off for more than
one minute.
AUTO, automatic
illumination of headlamps.
48 51
VISIBILITY
Motorway function: press the stalk up
o r d o w n t o fl a s h t h e d i r e c t i o n i n d i c a t o r
three times. 148
Lighting stalk Wiper stalk Changing bulbs
I n b a d w e a t h e r o r i n w i n t e r , e n s u r e t h a t
the lamps are not covered with mud or
snow.
Special position for the front wipers
For one minute after switching off the
ignition, any action on the wiper stalk
places the wiper arms and blades
vertically alongside the screen pillars. 52,
157
Page 28 of 223
33
READY TO GO
22
Instruments and controls
Warning lamp is indicates Solution - action
Particle
e m i s s i o n fi l t e r on. a fault with the particle
e m i s s i o n fi l t e r ( D i e s e l
additive level, risk of
blockage,...). H a v e t h e fi l t e r c h e c k e d b y a C I T R O Ë N d e a l e r .
Chapter 6, "Levels" section.
Dipped beam
headlamps/
Daytime
running lams
on. a manual selection or
automatic illumination of
headlamps.
Turn the ring on the lighting control stalk to the
second position.
illumination of the dipped beam headlamps
from the time the ignition is switched on:
daytime running lamps (depending on the
country in which the vehicle is sold).
Chapter 3, "Steering mounted controls" section.
Main beam
headlamps pulling of the stalk towards
you.
Pull the stalk to return to dipped beam headlamps.
Direction
indicators fl a s h i n g w i t h
audible signal. a change of direction via the
lighting stalk, to the left of
the steering wheel. To the Right: control to be pushed upwards.
To the Left: control to be pushed downwards.
Front
foglamps on. a manual selection. The fog amps only operate if the sidelamps or
dipped beam headlamps are on.
Rear
foglamps on. a manual selection. The foglamps only operate if the sidelamps or
dipped beam headlamps are on. In conditions of
normal visibility, switch them off to avoid breaking
the law. "This lamp is a dazzling red."
Page 47 of 223
50
Steering mounted controls
If the brightness sensor
does not function
correctly , the lights come on
a c c o m p a n i e d b y t h e s e r v i c e
w a r n i n g l i g h t , a n a u d i b l e
s i g n a l a n d a m e s s a g e o n t h e
d i s p l a y .
C o n s u l t a C I T R O Ë N d e a l e r .
Guide-me-home lighting
T h e t e m p o r a r y m a i n t a i n i n g o f t h e
d i p p e d h e a d l a m p s l i g h t i n g , w i t h t h e
i g n i t i o n o f f , m a k e s t h e d r i v e r ' s e x i t
e a s i e r w h e n t h e l i g h t i s p o o r .
HEADLAMP BEAM
D e p e n d i n g o n t h e l o a d i n y o u r v e h i c l e ,
t h e b e a m s e t t i n g m u s t b e a d j u s t e d .
0 - N o l o a d .
1 - P a r t i a l l o a d .
2 - A v e r a g e l o a d .
3 - M a x i m u m a u t h o r i s e d l o a d .
Manual operation
- W i t h t h e i g n i t i o n o f f , " fl a s h " t h e
h e a d l a m p s w i t h i n o n e m i n u t e a f t e r
switching off the ignition.
The guide-me-home lighting switches
o f f a u t o m a t i c a l l y a f t e r a s e t t i m e .
Automatic operation
R e f e r t o t h e " D i s p l a y fl o w c h a r t "
s e c t i o n o f c h a p t e r 9 .
Initial setting is position 0.
A c t i v a t e t h e f u n c t i o n v i a t h e
" V e h i c l e c o n fi g " m e n u .
Page 48 of 223
50
Steering mounted controls
If the brightness sensor
does not function
correctly , the lights come on
a c c o m p a n i e d b y t h e s e r v i c e
w a r n i n g l i g h t , a n a u d i b l e
s i g n a l a n d a m e s s a g e o n t h e
d i s p l a y .
C o n s u l t a C I T R O Ë N d e a l e r .
Guide-me-home lighting
T h e t e m p o r a r y m a i n t a i n i n g o f t h e
d i p p e d h e a d l a m p s l i g h t i n g , w i t h t h e
i g n i t i o n o f f , m a k e s t h e d r i v e r ' s e x i t
e a s i e r w h e n t h e l i g h t i s p o o r .
HEADLAMP BEAM
D e p e n d i n g o n t h e l o a d i n y o u r v e h i c l e ,
t h e b e a m s e t t i n g m u s t b e a d j u s t e d .
0 - N o l o a d .
1 - P a r t i a l l o a d .
2 - A v e r a g e l o a d .
3 - M a x i m u m a u t h o r i s e d l o a d .
Manual operation
- W i t h t h e i g n i t i o n o f f , " fl a s h " t h e
h e a d l a m p s w i t h i n o n e m i n u t e a f t e r
switching off the ignition.
The guide-me-home lighting switches
o f f a u t o m a t i c a l l y a f t e r a s e t t i m e .
Automatic operation
R e f e r t o t h e " D i s p l a y fl o w c h a r t "
s e c t i o n o f c h a p t e r 9 .
Initial setting is position 0.
A c t i v a t e t h e f u n c t i o n v i a t h e
" V e h i c l e c o n fi g " m e n u .
Page 50 of 223
5 2
Steering mounted controls
Wash-wipe and headlamp wash
P u l l t h e s t a l k t o w a r d s y o u , t h e w a s h -
w i p e i s a c c o m p a n i e d b y a t i m e d s w e e p
of the wipers.
T h e h e a d l a m p w a s h i s l i n k e d w i t h t h e
w a s h - w i p e , i t i s t r i g g e r e d i f t h e d i p p e d
h e a d l a m p s a r e o n .
T u r n t h e r i n g p a s t t h e fi r s t
n o t c h : t h e w i n d s c r e e n w a s h
then the windscreen wiper
o p e r a t e f o r a fi x e d t i m e .
I n w i n t e r , i n t h e e v e n t o f a
c o n s i d e r a b l e a m o u n t o f s n o w
o r i c e , s w i t c h o n t h e r e a r s c r e e n
demister. Once de-icing is complete,
r e m o v e t h e s n o w o r i c e w h i c h h a s
a c c u m u l a t e d o n t h e r e a r w i p e r
b l a d e . Y o u c a n t h e n o p e r a t e t h e r e a r
windscreen wiper.
T o t o p u p t h e l e v e l s , r e f e r t o t h e
" L e v e l s " s e c t i o n o f c h a p t e r 6 .
Special position of the
windscreen wipers
In the minute following switching
o f f o f t h e i g n i t i o n , a n y a c t i o n o n t h e
s t a l k p o s i t i o n s t h e w i p e r s a g a i n s t t h e
windscreen uprights.
T h i s a c t i o n e n a b l e s y o u t o p o s i t i o n
t h e w i p e r b l a d e s f o r w i n t e r p a r k i n g ,
c l e a n i n g o r r e p l a c e m e n t .
R e f e r t o t h e " C h a n g i n g a
w i n d s c r e e n w i p e r b l a d e " s e c t i o n o f
c h a p t e r 7 .
T o p a r k t h e w i p e r s i n t h e i r n o r m a l
p o s i t i o n a f t e r t h i s h a s b e e n d o n e ,
s w i t c h o n t h e i g n i t i o n a n d m o v e
t h e s t a l k . T u r n t h e r i n g t o t h e fi r s t n o t c h .
Rear windscreen wiper Rear windscreen wash
Page 139 of 223
136
Levels
Cooling system
O n l y u s e t h e fl u i d r e c o m m e n d e d b y t h e
manufacturer.
O t h e r w i s e , y o u r i s k s e r i o u s l y d a m a g i n g
your engine.
When the engine is warm, the
temperature of the coolant is controlled
by the engine fan. As this fan can
o p e r a t e w i t h t h e i g n i t i o n k e y r e m o v e d
and because the cooling system is
pressurised, wait for at least one hour
after the engine has stopped before
c a r r y i n g o u t a n y w o r k .
S l a c k e n t h e c a p b y 1 / 4 o f a t u r n t o
release the pressure to prevent any
r i s k o f s c a l d i n g . W h e n t h e p r e s s u r e
has dropped, remove the cap and top
up the level with coolant.
I f fl u i d h a s t o b e a d d e d f r e q u e n t l y ,
this indicates a fault which must be
c h e c k e d b y a C I T R O Ë N d e a l e r a s
soon as possible. Power steering fluid level
T h e v e h i c l e m u s t b e p a r k e d o n l e v e l
ground with the engine cold. Unscrew
the cap integrated with the gauge and
c h e c k t h e l e v e l w h i c h m u s t b e b e t w e e n
t h e M I N a n d M A X m a r k s .
I n o r d e r t o r e g e n e r a t e t h e fi l t e r , y o u a r e
advised to drive at a speed higher than
4 0 m p h ( 6 0 k m / h ) f o r a t l e a s t fi v e m i n u t e s
a s s o o n a s p o s s i b l e , w h e n t r a f fi c c o n d i t i o n s
p e r m i t ( u n t i l t h e m e s s a g e d i s a p p e a r s a n d
t h e s e r v i c e w a r n i n g l a m p g o e s o f f ) .
During regeneration of the particle emission
fi l t e r , t h e n o i s e o f a r e l a y o p e r a t i n g m a y b e
heard under the dashboard.
If the message is still displayed and if the
service warning lamp remains on, consult a
CITROËN dealer.
Topping up
The level must be between the MIN
a n d M A X m a r k s o n t h e e x p a n s i o n
b o t t l e . I f m o r e t h a n 1 l i t r e o f fl u i d i s
required to top up the level, have the
s y s t e m c h e c k e d b y a C I T R O Ë N d e a l e r . Screenwash and headlamp
wash level
For best quality cleaning and for your
safety, we would advise that you use
products of the CITROËN range.
For optimum cleaning and to avoid
f r e e z i n g , t h i s fl u i d m u s t n o t b e t o p p e d
up or replaced with plain water.
Capacity of the screenwash reservoir:
approximately 3 litres.
I f y o u r v e h i c l e i s fi t t e d w i t h h e a d l a m p
washers, the capacity of the reservoir
is 6 litres.
Diesel additive level
(Diesel with particle
emission filter)
The minimum level of this
additive is indicated by lighting of the
service warning lamp, accompanied
by an audible signal and a message in
the screen.
When this occurs with the engine
running it is due to the start of
s a t u r a t i o n o f t h e p a r t i c l e e m i s s i o n fi l t e r
( e x c e p t i o n a l l y p r o l o n g e d u r b a n t y p e
driving conditions: low speed, long
t r a f fi c j a m s , . . . ) . Topping up
It is imperative that this additive is
topped up by a CITROËN dealer
without delay.
Used oil
Avoid prolonged contact of used oil
w i t h t h e s k i n .
B r a k e fl u i d i s h a r m f u l t o h e a l t h a n d
very corrosive.
D o n o t d i s p o s e o f u s e d o i l , b r a k e fl u i d
or coolant into drains or into the ground
but into the containers dedicated to this
u s e a t C I T R O Ë N d e a l e r ( F r a n c e ) o r a n
authorised waste disposal site.
Page 154 of 223
149
QUICK HELP
7
Changing a bulb
3. Direction indicators
Type B , PY21W - 21W (amber)
- R e m o v e t h e c o v e r b y p u l l i n g t h e fl e x i b l e r u b b e r t a b .
- T u r n t h e b u l b h o l d e r a q u a r t e r t u r n a n t i c l o c k w i s e .
- R e m o v e t h e b u l b b y p r e s s i n g it lightly while turning it
a n t i c l o c k w i s e .
- C h a n g e t h e b u l b .
- E n s u r e t h a t t h e c o v e r i s r e fi t t e d correctly all round to assure
correct sealing.
2. Sidelamps
Type A , W 5 W - 5 W
- R e m o v e t h e c o v e r b y p u l l i n g t h e fl e x i b l e r u b b e r t a b .
- R e m o v e t h e b u l b h o l d e r fi t t e d b y p r e s s u r e b y p u l l i n g t h e c o n n e c t o r .
- C h a n g e t h e b u l b .
- E n s u r e t h a t t h e c o v e r i s r e fi t t e d correctly all round to assure
correct sealing.
FRONT LAMPS
1. Dipped/Main beam headlamps
Type C , H 4 - 5 5 W
- R e m o v e t h e c e n t r e c o v e r b y p u l l i n g t h e fl e x i b l e r u b b e r t a b .
- Disconnect the electrical connector.
- R e l e a s e t h e r e t a i n i n g t a b .
- C h a n g e t h e b u l b t a k i n g c a r e t o a l i g n t h e m e t a l p a r t w i t h t h e
g r o o v e s o n t h e l a m p .
- R e p o s i t i o n t h e r e t a i n i n g t a b .
- E n s u r e t h a t t h e c o v e r i s r e fi t t e d correctly all round to assure
correct sealing.