door lock Citroen BERLINGO FIRST DAG RHD 2009 1.G Owner's Manual

5FAMILIARISATION-
INSTRUMENTS AND CONTROLS

12. Windscreen demisting vents.

13. Speaker (tweeter).

14. Door window demisting vents.

15. Side adjustable heating/
ventilation vents.

16.
Passenger air bag disarming control.

17. Upper glove box or passenger air bag.

18. Lower glove box.

19. RD3 audio equipment.

20. Heating/air conditioning controls.

21. Storage compartment.

22. Movable ashtray.

23. Gear lever.

24. Lighter.

25. Handbrake.
26. Heated seats control.

27. Steering lock and ignition.

28. Steering wheel adjustment
control.

29. Bonnet release.

30. Fuse box.

31. Headlamp height adjustment.

32. Passenger's electric mirror
control.

1. Speed limiter/cruise control
switch.

2. Lights and direction indicators
controls.

3. Driver's air bag.
Horn.

4. Instrument panel.

5. Audio equipment steering wheel
control.

6. Wipers/wash-wipe controls.

7. Central adjustable heating/
ventilation vents.

8. Hazard warning lights switch.

9. Multifunction display or clock.

10. Central locking button.

11. Controls:
- Electric windows.
- Rear door windows or tailgate demisting.
- Air conditioning.

FAMILIARISATION6 -
THE KEYS
The keys allow you to switch on the
ignition and operate the passenger
air bag disarming switch, as well as
to independently operate the locks
on the doors and the fuel fi ller cap.
STARTING The remote control
Central locking
From the front doors, the keys allow
you to lock and unlock the doors and
tailgate.
If one of the doors or the tailgate is
open, it is impossible to operate the
central locking.

The remote control performs the
same functions at a distance. Unlocking
Press button
B to unlock the vehicle.
This is confi rmed by rapid fl ashing of
the direction indicators.
Locating the vehicle
To locate your vehicle, previously
locked, in a car park:

 press button A , the courtesy lights
come on and the direction indica-
tors fl ash for a few seconds.

 54
Locking
Press button
A to lock the vehicle.
This is confi rmed by fi xed lighting of
the direction indicators for approxi-
mately two seconds. STOP position (S):
The ignition is off.
To release the steering, turn the
steering wheel slightly while turning
the key, without forcing it.
Accessories position (A):
The ignition is off but the accessories
can be used.
On position (M):
The ignition is on.
Starting position (D):
Operates the starter.
Release the key when the engine
has started. Never operate the starter
while the engine is running.

INSTRUMENTS, CONTROLS and DISPLAYS22 - Service indicator
This is a visual reminder of when the
next service is due. This service is to
be carried out according to the manu-
facturer's servicing schedule. 5 seconds after the ignition is switched
on, the total distance recorder resumes
normal operation and the display shows
the total or trip distances.
The distance remaining before the next
service is less than 500 miles (1,000 km).

Example: 400 miles (900 km) remain
before the next service is due.
When switching on the ignition and
for 5 seconds, the display shows:
5 seconds after the ignition is
switched on, the total distance re-
corder resumes normal operation
and the symbol remains lit.
This indicates that a service should
be carried out shortly. The display
shows the total or trip distances. The service is overdue.
Each time the ignition is switched on
and for 5 seconds, the symbol and
the excess distance fl ash.

Example: the service is overdue by
300 miles/km. The service should be
carried out very shortly.
When the ignition is switched on and
for 5 seconds, the display shows:
5 seconds after the ignition is
switched on, the total distance re-
corder resumes normal operation and
the symbol remains lit. The display
shows the total or trip distances.

Note: the spanner lights if the two-year
interval has been exceeded.
INSTRUMENT PANEL DISPLAY
After switching on the ignition, three
functions are shown in succession:
- service indicator,
- engine oil level indicator,
- total distance recorder/total and trip distances.

Note
: the total and trip distances are
displayed for 30 seconds when the
ignition is switched off, on opening
the driver's door, as well as on lock-
ing and unlocking the vehicle.

Example: 4,800 miles/km remain be-
fore the next service is due. When the
ignition comes on and for 5 seconds
the display shows:
Operation
As soon as the ignition is switched
on and for 5 seconds, the spanner
symbolising ''service operation'' is lit.
The trip recorder display shows the
distance remaining (in round fi gures)
before the next service.

41SEATS-
FRONT SEATS

The adjustment is correct when
the upper edge of the head re-
straint is level with the top of the
head.
To remove the head restraint, place it
in the top position, press the tabs and
pull it upwards.
To put it back in position, locate the
stems of the restraint in the holes,
taking care to keep them in line with
the seat back.
No person or object must pre-
vent the seat from returning
to its initial position; return to
this position is necessary for
the seat to lock in place.
4. Forwards-backwards
adjustment
Lift the control and slide the seat for-
wards or backwards.
1. Head restraint height
adjustment
To raise or lower the restraint, slide it.
2. Armrests
These can be folded back. 3. Seat back angle adjustment
5. Storage drawer (version with
passenger air bag)
There is a storage drawer under the
front passenger seat.
To open it, lift it and pull. 6. Heated seats switch
Press the switch. The temperature is
controlled automatically.
Pressing the switch again stops op-
eration.

Note: the command for activation of
heating of the seat(s) remains mem-
orised for two minutes after the igni-
tion has been switched off.
7. Access to rear seats (version with one
sliding side door only)
Do not place heavy objects
in the drawers.
A. Turn the knob.

B. Pull the lever (version
with one sliding side
door only).
Never drive with the head re-
straints removed; they must
be in place and correctly ad-
justed. Lift the control to fold the seat back
and move the seat forwards.
On repositioning, the seat returns to
its initial position (driver's side).

45SEATS-
Row 3 bench seat
Placing the seat back in the table
position
- Lower the head restraints fully.
- Operate the two controls simulta-neously to fold the seat back onto
the bench seat cushion.
Returning the seat back to the sitting position
- Return the seat back to its original position and check that it is se-
cured on the pillars of the vehicle. Placing the bench seat in the fully
folded position
- Place the seat in the table posi-
tion.
- Raise the handle, located behind the bench seat, to release the
feet from their anchorage on the
fl oor.
- Tilt the bench seat forwards.
Returning the bench seat to its
original position
- Before folding back the bench seat, ensure that the seat belt
is available for the side passen-
gers.
- Fold back the bench seat.
Access to row 3
From the vehicle's right-hand sliding
door, a passage next to the row 2
bench seat provides access to the
row 3 bench seat.
Good practice
Do not place hard or heavy
objects on the seat backs
forming a table, they could
become dangerous projectiles in the
event or sharp braking or impact.
Following the various operations:
- do not remove a head restraint without storing it, fi x it to a sup-
port in the vehicle,
- do not block the passage to row 3,
- ensure that the passengers can always access the seat belts and
fasten them easily,
- a passenger must never take his seat without adjusting and fasten-
ing his seat belt.
- a passenger seated in row 3 must ensure that he does not obstruct
the row 2 bench seat anchoring
recesses.

51SEATS-
ADVICE ON CHILD SEATS
The incorrect installation of a
child seat in a vehicle com-
promises the child's protection in the
event of an accident.
Remember to fasten the seat belts or
the child seat harnesses keeping the
slack in relation to the child's body to
a minimum, even for short journeys.
For optimum installation of the "for-
ward facing" child seat, ensure that
the back of the child seat is in contact
with the back of the vehicle's seat
and that the head restraint does not
cause any discomfort.
If the head restraint has to be re-
moved, ensure that it is stored or
attached securely to prevent it from
being thrown around the vehicle in
the event of sharp braking. Children under the age of 10 must not
travel in the "forward facing" position
on the front passenger seat, unless
the rear seats are already occupied
by other children, cannot be used or
are absent.
Disarm the passenger air bag when
a "rear facing" child seat is installed
on the front seat. Otherwise, the child
would risk being seriously injured or
killed if the air bag were to infl ate.
As a safety precaution, do not leave:
- one or more children alone and
unsupervised in a vehicle,
- a child or an animal in a vehicle which is exposed to the sun, with
the windows closed,
- the keys within reach of children inside the vehicle.
Installing a booster seat
The chest part of the seat belt must
be positioned on the child's shoulder
without touching the neck.
Ensure that the lap part of the seat
belt passes correctly over the child's
thighs.
CITROËN recommends the use of
a booster seat which has a back, fi t-
ted with a seat belt guide at shoulder
level. To prevent accidental
opening of the doors, use
the "Child lock".
Take care not to open the
rear windows by more than
one third.
To protect young children from the
rays of the sun, fi t side blinds on the
rear windows.

51SEATS-
ADVICE ON CHILD SEATS
The incorrect installation of a
child seat in a vehicle com-
promises the child's protection in the
event of an accident.
Remember to fasten the seat belts or
the child seat harnesses keeping the
slack in relation to the child's body to
a minimum, even for short journeys.
For optimum installation of the "for-
ward facing" child seat, ensure that
the back of the child seat is in contact
with the back of the vehicle's seat
and that the head restraint does not
cause any discomfort.
If the head restraint has to be re-
moved, ensure that it is stored or
attached securely to prevent it from
being thrown around the vehicle in
the event of sharp braking. Children under the age of 10 must not
travel in the "forward facing" position
on the front passenger seat, unless
the rear seats are already occupied
by other children, cannot be used or
are absent.
Disarm the passenger air bag when
a "rear facing" child seat is installed
on the front seat. Otherwise, the child
would risk being seriously injured or
killed if the air bag were to infl ate.
As a safety precaution, do not leave:
- one or more children alone and
unsupervised in a vehicle,
- a child or an animal in a vehicle which is exposed to the sun, with
the windows closed,
- the keys within reach of children inside the vehicle.
Installing a booster seat
The chest part of the seat belt must
be positioned on the child's shoulder
without touching the neck.
Ensure that the lap part of the seat
belt passes correctly over the child's
thighs.
CITROËN recommends the use of
a booster seat which has a back, fi t-
ted with a seat belt guide at shoulder
level. To prevent accidental
opening of the doors, use
the "Child lock".
Take care not to open the
rear windows by more than
one third.
To protect young children from the
rays of the sun, fi t side blinds on the
rear windows.

ACCESS and STARTING54 -
KEYS
The keys allow you to switch on the
ignition and operate the passenger
air bag disarming switch as well as to
independently operate the locks on
the doors and the fuel fi ller cap. Locating your vehicle
To locate your vehicle, if you have
locked it, in a car park:

 press button A , the courtesy lights
come on and the direction indica-
tors fl ash for a few seconds. Changing the battery of the
remote control
CR 2016/3 volt battery.
The information "battery fl at" is given by
an audible signal accompanied by the
message
"Remote control battery
fl at" on the screen.
To change the battery, unclip the
casing using a coin at the ring.
If the remote control does not work
after the battery has been changed,
re-programme the remote control.
Programming the remote
control

 Switch off the ignition.

 Switch the ignition on again.

 Press button A immediately for a
few seconds.

 Switch off the ignition and remove
the remote control key from the
ignition lock. The remote control
is now working again.
Remote control
Central locking
From the front doors, the keys allow
you to lock and unlock the doors and
tailgate.
If one of the doors or the tailgate is
open, the central locking does not
work.

The remote control performs the
same functions at a distance. Locking
Press button
A to lock the vehicle.
This is confi rmed by fi xed lighting of
the direction indicators for approxi-
mately two seconds.
Unlocking
Press button B to unlock the vehicle.
This is confi rmed by rapid fl ashing of
the direction indicators.

Note : if the vehicle is locked and
unlocking is activated inadvertently,
unless the doors are opened within
30 seconds, the vehicle will lock au-
tomatically.

55ACCESS and STARTING-
ELECTRONIC ENGINE IMMOBILISER
This locks the engine control sys-
tem as soon as the ignition has been
switched off and therefore prevents
starting of the vehicle by anyone who
does not have the key.
The ignition key has an electronic
chip which has a special code. When
the ignition is switched on, the code
must be recognised for the vehicle to
start.

If the system does not function
correctly, the central locking button
indicator light, situated in the centre
of the fascia, fl ashes rapidly when the
ignition is switched on (2nd notch),
accompanied by an audible signal
and a message on the display.
In this case your vehicle will not
start.
Contact a CITROËN dealer as soon
as possible.
Key in ignition
A buzzer sounds on opening the
driver's door, if the key has been left
in the ignition. Make a careful note of the
number of each key. This
number is coded on the label
attached to the key.
The high frequency remote control is
a sensitive system; do not operate it
while it is in your pocket as there is a
possibility that it may unlock the vehi-
cle, without you being aware of it.
The remote control does not operate
when the key is in the ignition, even
when the ignition is switched off,
except for reprogramming.
Driving with the doors locked may
make access to the passenger com-
partment by the emergency services
more diffi cult in an emergency.
As a safety precaution (with children
on board), remove the key from the
ignition when you leave the vehicle,
even for a short time.
Do not repeatedly press the buttons
of your remote control out of range of
your vehicle.
You run the risk of stopping it from
working and the remote control would
have to be reprogrammed.
When purchasing a second-hand ve-
hicle, have the key codes memorised
by a CITROËN dealer, to ensure that
the keys in your possession are the
only ones which can start the vehicle.
Do not make any modifi cations to the
electronic engine immobiliser system. If the keys are lost
Visit a CITROËN dealer with the vehi-
cle's V5 registration certifi cate and your
personal identifi cation documents.
The CITROËN network will be able to
retrieve the key code and the trans-
ponder code to order a replacement
key.
A heavy object (key fob...), attached
to the key and weighing down on
its shaft in the ignition switch, could
cause a malfunction.

ACCESS and STARTING54 -
KEYS
The keys allow you to switch on the
ignition and operate the passenger
air bag disarming switch as well as to
independently operate the locks on
the doors and the fuel fi ller cap. Locating your vehicle
To locate your vehicle, if you have
locked it, in a car park:

 press button A , the courtesy lights
come on and the direction indica-
tors fl ash for a few seconds. Changing the battery of the
remote control
CR 2016/3 volt battery.
The information "battery fl at" is given by
an audible signal accompanied by the
message
"Remote control battery
fl at" on the screen.
To change the battery, unclip the
casing using a coin at the ring.
If the remote control does not work
after the battery has been changed,
re-programme the remote control.
Programming the remote
control

 Switch off the ignition.

 Switch the ignition on again.

 Press button A immediately for a
few seconds.

 Switch off the ignition and remove
the remote control key from the
ignition lock. The remote control
is now working again.
Remote control
Central locking
From the front doors, the keys allow
you to lock and unlock the doors and
tailgate.
If one of the doors or the tailgate is
open, the central locking does not
work.

The remote control performs the
same functions at a distance. Locking
Press button
A to lock the vehicle.
This is confi rmed by fi xed lighting of
the direction indicators for approxi-
mately two seconds.
Unlocking
Press button B to unlock the vehicle.
This is confi rmed by rapid fl ashing of
the direction indicators.

Note : if the vehicle is locked and
unlocking is activated inadvertently,
unless the doors are opened within
30 seconds, the vehicle will lock au-
tomatically.