service Citroen BERLINGO MULTISPACE RHD 2014.5 2.G Owner's Guide

Berlingo_2_VP_en_Chap07_Verification_ed02-2014
151
When switching on the ignition, the
SERVICE  warning   lamp   comes   on  
and

  the   UREA
 
warning   lamp   flashes,  
accompanied

  by   an   audible   signal   and  
the

  display   of   a   message   (e.g.   "Top   up  
emissions

  additive:   Starting   prevented  
in

  350   miles")   indicating   the   remaining  
range

  expressed   in   miles   or   kilometres.
When
  driving,   the   message   is  
displayed every 30 seconds until the
additive

  tank   has   been   topped-up.
Go
  to   a   CITROËN   dealer   or   a   qualified  
workshop

  to   have   the  
AdBlue® tank topped-up.
Y
ou
 
can
 
also
 
top-up
 
the
 
tank
 
yourself.
Refer
 
to
 
the
 
"Topping-up"
 
section.
o

therwise you will not be able to
restart
 
your
 
engine. When switching on the ignition, the
SERVICE
  warning   lamp   comes   on  
and

  the   UREA
 
warning   lamp   flashes,  
accompanied

  by   an   audible   signal  
and

  the   display   of   the   message  
"T

op   up   emissions   additive:   Starting  
prevented".
The

a dBlue
® tank is empty: the system required
 
by
 
regulations   prevents  
engine

 
starting. To be able to start the engine,
we
  recommend   that   you   call   on  
a

  CITROËN   dealer   or   a   qualified  
workshop

  for   the   top-up   required.   If  
you carry out the top-up yourself, it is
essential

  to   add   at   least   3.8   litres   of  
a dBlue
® to the tank.
r

emaining range between 0 and
350 miles (0 and 600 km) Breakdown related to a lack of
AdBlue
® additive
Refer   to   the   "Topping-up"   section.
adBlue® additive
CHECkS
7

Berlingo_2_VP_en_Chap07_Verification_ed02-2014
152
In the event of a fault with
the the Scr emissions control
system
When switching on the ignition, the
URE
a , SERVICE and diagnostic
warning
  lamps   comes   on,   accompanied
 by an audible signal and the display of


a
  message   "Emissions   fault"   to   signal   a
 fault

  with   the   emissions   control   system.
If
  it   is   a   temporary   fault,   the   alert  
disappears once the exhaust gas
emissions

  return   to   normal.during an authorised driving phase (between
650 miles and 0 miles) (1 100 km and 0 km)
A  system   that   prevents   engine  starting
  is   activated   automatically  
from

  650   miles   (1   100   km)   after  
confirmation

  of   a   fault   with   the   SCR  
emissions

  control   system.   Have   the  
system

  checked   by   a   CITROËN   dealer  
or

 
a
 
qualified   workshop   as   soon   as  
possible. In the event of the detection


of a fault
If   a   fault   with   the   SCR   system   is  
confirmed

  (after   30   miles   (50   km)  
covered

  with   the   permanent   display   of  
the

  message   signalling   a   fault),   when  
switching on the ignition, the SER

VICE
and
  engine   diagnostic   warning   lamps  
come

  on   and   the   UREA
 
warning   lamp  
flashes,

  accompanied   by   an   audible  
signal

  and   the   display   of   a   message  
(e.g.:

  "Emissions   fault:   Starting  
prevented

  in   150   miles")   indicating   the  
remaining

  range   express   in   miles   or  
kilometres.
While

  driving,   the   message   is  
displayed every 30 seconds while the
fault

  with   the   SCR   system   persists.
You should go to a CITR
o Ë n dealer
or
  a   qualified   workshop   as   soon   as  
possible.
o

therwise, you will not be able to
restart
  your   engine.
adBlue® additive

Berlingo_2_VP_en_Chap07_Verification_ed02-2014
153
Every time the ignition is switched on, the SERVICE and engine diagnostic
warning
  lamps   come   on   and   the   UREA
 warning

  lamp   flashes,   accompanied  
by an audible signal and the display of
the

  message   "Emissions   fault:   Starting  
prevented".
Y

ou have exceeded the authorised
driving
  limit:   the   starting  
prevention

  system   inhibits   engine  
starting.
T

o be able to start the engine, you
must
  call   on   a   CITROËN   dealer   or   a  
qualified

  workshop.
Starting prevented
The a dBlue
® additive freezes at
temperatures   below   around   -11°C.
The
 
SCR
 
system   includes   a   heater   for  
the

a
dBlue
® tank.
In
 
exceptional   circumstances   (vehicle  
kept

 
for
 
a
 
long   period   at   temperatures  
that

 
are
 
constantly   below   -15°C),   an  
emissions

 
control   system   fault   alert  
may

 
be
 
related   to   freezing   of   the  
a
dBlue
® in your vehicle.
Park
 
your   vehicle   in   a   warmer   area   for  
a

 
few
 
hours   until   the   additive   becomes  
liquid

 
again.
The
 
emissions   alert   does   not   go   off  
immediately

,   it   will   occur   after   several  
mile

 
of
 
running.
Freezing of the AdBlue
® additive
adBlue® additive
CHECkS
7

Berlingo_2_VP_en_Chap07_Verification_ed02-2014
154
topping-up the AdBlue® additive
Filling the adBlue® tank is an operation included in every routine service on
your vehicle by a CITR
o Ë n dealer
or
 
a
 
qualified
 
workshop.
n

evertheless, given the capacity
of
 
the
 
tank,
 
it
 
may
  be   necessary   to  
top-up the additive between services,
more

 
particularly
 
if   an   alert   (warning  
lamps

 
and
 
a
 
message)   signals   the  
requirement.
Y

ou can got to a CITR o Ë n dealer
or
 
a
 
qualified
 
workshop.
If you envisage topping-up yourself,
please read the following warnings
carefully. Precautions in use
The
a dBlue® additive is an urea-based
solution.
 This   liquid   is   non-flammable,  
colourless

 
and   odourless   (kept   in   a  
cool

 
area).
In
 
the
 
event
 
of   contact   with   the   skin,  
wash the af

fected area with soap and
water.
 
In
 
the
  event   of   contact   with   the  
eyes, wash (irrigate) the eyes with
large

 
amounts   of   water   or   with   an   eye  
wash

 
solution   for   at   least   15   minutes.  
If a burning sensation or irritation
persists,

 
get
  medical   attention.
If
 
swallowed,   immediately   wash   out   the  
mouth

 
with
 
clean   water   and   then   drink  
plenty

 
of
 
water.
In
 
certain
 
conditions   (high   ambient  
temperature,

  for   example),   the   risk  
of

 
release
 
of
  ammonia   cannot   be  
excluded:

 
do   not   inhale   the   product.  
Ammonia

 
vapour   has   en   irritant   effect  
on

 
mucous
 
membranes   (eyes,   nose  
and

 
throat).
k

eep
a
dBlue
® out of the reach of
children,
 
in
 
its
  original   bottle.
n

ever transfer
a
dBlue
® to another
container:
 
it
 
would
 
loose   its   purity. Use only
a dBlue
® additive that meets the
 
ISO
 
22241
 
standard.
n

ever dilute the additive with
water.
n

ever pour the additive into the d iesel
fuel
 
tank.
The supply in a non-drip bottle
simplifies
 
toping-up.  
Y
ou   can   obtain  
1.89

 
litre
 
(half
 
a
 
US   gallon)   bottles  
from

 
a
 
CITROËN dealer   or   a   qualified  
workshop.Never

 
top-up   from   an  
AdBlue®
dispenser reserved for heavy
goods
 
vehicles.
adBlue® additive

10.2
Berlingo_2_VP_en_Chap10a_BTa_ed02-2014
EMErGEncY O r ASSIS tA nc E c ALL
cItrOËn Localised Emergency call
In an emergency, press this button for more than 2 seconds. Flashing
  of   the   green   LED   and   a   voice   message   confirm  
that

  the   call   has   been   made   to   the   CITROËN   Localised  
Emergency

  Call   centre*.
Pressing
 
this   button   again   immediately   cancels   the   call.  
The
  green   LED  
goes

 
off.
Pressing
 
this   button   (at   any   time)   for   more   than   8   seconds   cancels   the  
call.
cItrOËn Localised Assistance call
When the ignition is switched on, the green
LED  comes   on   for   3   seconds   indicating   that  
the

  system   is   operating   correctly.
If
  the   orange   LED   flashes:   there   is   a   system  
fault.
If

  the   orange   LED   is   on   continuously:   the  
backup

  battery   must   be   replaced.
In
  either   case,   contact   a   CITROËN   dealer.
Pressing
 
this
 
button
 
again
 
immediately   cancels   the   request.
The
 
cancellation
 
is
 
confirmed
  by   a   voice   message.
Press
 
this
 
button   for   more   than   2   seconds   to   request  
assistance

 
if
 
the   vehicle   breaks   down.
A
 

voice
 
message   confirms   that   the   call   has   been   made*.
Operation of the system
The green LED remains on (without flashing) when communication is established.
  It   goes   off   at   the   end   of   communication.
This
  call   is   dealt   with   by   the   CITROËN   Localised   Emergency   Call   centre  
which

  receives   locating   information   from   the   vehicle   and   can   send   a  
detailed

  alert   to   the   appropriate   emergency   services.   In   countries   in  
which

  the   team   is   not   operational,   or   when   the   locating   service   has  
been

  expressly   declined,   the   call   is   dealt   with   directly   by   the   emergency  
services

  (112)   without   the   vehicle   location.
If
  an   impact   is   detected   by   the   airbag   control   unit,   and  
independently

  of   the   deployment   of   any   airbags,   an   emergency  

call

  is   made   automatically.
*
 
These
  services   are   subject   to   conditions   and   availability.
 Consult

  a   CITROËN   dealer. If
  you   purchased   your   vehicle   outside   the   CITROËN   dealer   network,  
we

  invite   you   to   have   a   dealer   check   the   configuration   of   these   services  
and,

  if   desired,   modified   to   suit   your   wishes.   In   a   multi-lingual   country,  
configuration

  is   possible   in   the   official   national   language   of   your   choice.
For
  technical   reasons,   particularly   to   improve   the   quality   of  
T
elematic  
services

  to   customers,   the   manufacturer   reserves   the   right   to   carry   out  
updates

  to   the   vehicle's   on-board   telematic   system.
If
  you   benefit   from   the   CITROËN   eTouch   offer,   you   also   have   available  
additional

services in your MyCITR o Ë n personal space, via the CITR o Ë n
Internet
  website   in   your   country,   accessible   on   www.citroen.com.

03
10.8
Berlingo_2_VP_en_Chap10b_RT6-2-8_ed02-2014
A press   on   the   knob   gives   access  to
  short-cut   menus   according   to   the  
display

  in   the   screen.
display according to context
r

A
d
IO:
c

hange waveband M
u SI c ME d IA PLAYE r S,
cd

or u SB (according to
media):
Play modes:
normal
r

andom
r

andom on all media
r

epetition
t

ELEPHO n E
(call in progress):
Private mode F u LL S cr EE n MAP O r I n A
n

EW WI nd OW:
Stop / r estore guidance
Select destination
Enter an address
d

irectory
GPS coordinates
divert route
Move the map
Info. on location
Select as destination
Select as stage
Save this place (contacts)
Quit map mode
Guidance criteria
Put call on hold
dt

MF ring tones
Hang up
1
1
1
1
1
1
1
2
2
2
2
2
1
2
2
2
1
1
1
1
1
1FM
Traffic announcements (TA) AM
Information
Entertainment
Special or
u rgent2
2
2
2
2
2
Services announcements1
GEnErAL OPE r At IO n

04
10.13
Berlingo_2_VP_en_Chap10b_RT6-2-8_ed02-2014
towards points of interest (POI)The points of interest (P o I) indicate all of the service locations in the vicinity
(hotels,   various   businesses,   airports...).
Select the "Enter an address" function
and
  confirm,   then   select   Select
destination
 

and   confirm.
To select a P
o I close to your current
location, select " POI"
  and   confirm,   then  
select "

Around the current place" and
confirm.
To select a P
o I as a stage on the route,
select "POI"
  and   confirm,   then   select  
"On the route "
  and   confirm.
To
  select   a   POI   as   a   destination,   first  
enter the country and town (see "T

owards
a new destination"), select " POI" and
confirm,
  finally   select   "
n
ear"
  and   confirm. Search for P
o Is in the categories
suggested
  in   the   following   pages.
Select "Search by
n ame"
  to   search   for   POIs   by   name   and   not   by  
proximity

.
Select
  the   POI   and   confirm   "OK" to start
the
  guidance.
Press
n
AV to display the
"

n avigation - guidance "
  menu.
nAVIGAtIO n - Gu I d A nc E

04
10.14
Berlingo_2_VP_en_Chap10b_RT6-2-8_ed02-2014
nAVIGAtIO n - Gu I d A nc E
This icon appears when several PoIs are grouped
together   in   the   same   area.   Zooming   in   on   this   icon  
shows

  details   of   the   POIs.
Service station
Garage
CITR
o
Ë
n
Covered

 
car
 
park
Car
 
park
Rest area
Hotel
Restaurant
Cafeteria
Bed
 
and
 
breakfast Railway station
Bus station
Port
Industrial estate
Supermarket
Vending
 
machine
Sports
 
complex,
 
sports   centre,  
sports ground
Swimming

 
pool
Winter sports resort
a

irport Theme
  parks
Hospital,
  Chemist,   Vet
Police station
Town hall
Post
  office
Museum,
  Culture,  
Theatre,
 
Historic

  monument
Tourist
  information,  
T
ourist  
attraction
Risk

  areas   /   Danger   areas*
List of principal points of interest (POI)
* according to availability in the
country.
School
An
 
annual
 
mapping
 
update
 
allows
 
new
 
points
 
of
 
interest
 
to
 
be
 
presented
 
to
 
you.
You
 
can
 
also
 
update
 
the
 
Risk
 
areas
 
/
 
Danger
 
areas
 
every
 
month.
The
 
detailed
 
procedure
 
is
 
available
 
on:
http://citroen.navigation.com. Cinema

05
10.24
Berlingo_2_VP_en_Chap10b_RT6-2-8_ed02-2014
Principal tM c symbols
Red and yellow triangle: traffic information, for example:
Black   and   blue   triangle:   general   information,   for   example:
Weather reports
Modified
  signage
Risk
  of   explosion Traffic
  reports
n

arrow carriageway
Road closed
Wind
Slippery surface
Demonstration Fog
a

ccident
d

anger
Parking
d

elay
n

o entry Snow
  /   ice
Roadworks
Traffic
  jam
receiving tA messages
The TA (Traffic  Announcement)   function   gives   priority   to  T A  alert  messages.
 T o   operate,   this   function   needs   good   reception   of   a  
radio

  station   transmitting   this   type   of   message.   When   a   traffic   report  
is

  transmitted,   the   current   audio   source   (Radio,   CD,   USB,   ...)   is  
interrupted

  automatically   to   play   the  
T
A
 
message.   Normal   playback  
of

  the   audio   source   resumes   at   the   end   of   the   transmission   of   the  
message.Press

r A d IO   to   display   the   menu.
Select "Service announcements" then
confirm.
a

ctivate or deactivate " t A"
  then   confirm.
The
  volume   setting   for  
T
A
 
messages   can   be   adjusted   only   during   the  
transmission

  of   this   type   of   alert.
Activate
  or   deactivate   the   function   at   any   time   by   pressing  
the

  button.
During
  a   message,   press   the   button   to   interrupt   it.
trAFFIc InFOrMAtIO n

06
10.26
Berlingo_2_VP_en_Chap10b_RT6-2-8_ed02-2014
uSInG tHE tELEPHOnE
Pairing a Bluetooth telephone
First connectionFor reasons of safety and because they require prolonged attention on the part of the driver, the operations for pairing the Bluetooth
mobile
  telephone   to   the   hands-free   system   of   the   audio   unit   must   be  
carried out with the vehicle stationary

.
In
 
the
 
Bluetooth
 
menu
 
of
 
your
 
telephone,
 
select
 
the
 
name

 
"C
ITR
o
Ë
n"
 
from
 
the
 
list
 
of
 
devices
 
detected. Press
  this   button.
Select "Bluetooth functions " and
confirm.
Select "Peripherals search " and
confirm.
The list of peripheral devices detected
is
  displayed.   Wait   until   the   " c onnect"
button
  is   available.
You
 
can
 
check
 
the
 
compatibility
 
of
 
your
 
telephone
 
at
 

www

.citroen.co.uk
 
(services).
a

ctivate the telephone's Bluetooth function
and ensure that it is "visible to all" (telephone
configuration).
Quick procedure from the telephone
Enter
 
a
 
minimum
 
4
 
figure
 
code
 
in
 
the
 
telephone
 
and
 
confirm. Enter

 
the
 
same
 
code
 
in
 
the
 
system,
 
select "

OK"
 
and
 
confirm. Procedure from the system