ignition Citroen BERLINGO MULTISPACE RHD 2014.5 2.G Owner's Guide

Page 108 of 276

106
Berlingo_2_VP_en_Chap05_Securite_ed02-2014
HAZArd WArnInG LAMPS
HO rn
Press the centre of the steering wheel.
PArKInG BrAKE
Applying
Pull the parking brake lever up to immobilise   your   vehicle.
Check
  that   the   parking   brake   is   applied  
firmly

  before   leaving   the   vehicle.Pull
  on   the   parking   brake   lever,   only
with the vehicle stationary.
In the exceptional case of use of the
parking
  brake   when   the   vehicle   is  
moving,

  apply   the   brake   by   pulling  
gently

  to   avoid   locking   the   rear   wheels  
(risk

  of   skidding).
Press this button, the direction
indicators
 
flash.
They
 
can
 
operate
 
with
 
the
 
ignition
 
off.
The
 
hazard
 
warning
 
lamps
 
should
 
only
 
be used in dangerous situations, when
stopping

 
in
 
an
 
emergency
 
or
 
when
 
driving

 
in
 
unusual
 
conditions.
When
  parking   on   a   slope,   direct   your  
wheels

  towards   the   pavement   and   pull  
the

  parking   brake   lever   up.
There is no advantage in engaging
a
  gear   after   parking   the   vehicle,  
particularly

  if   the   vehicle   is   loaded.
If the parking brake is still on or has not been released properly, this is
indicated
  by   this   warning   lamp   which
 comes

  on   on   the   instrument   panel.
Automatic operation of hazard
warning lamps
When braking in an emergency, depending on the force of deceleration,
the  hazard   warning   lamps   come  
on

  automatically.  
They
  switch   off  
automatically

  the   first   time   you  
accelerate.
It

  is   also   possible   to   switch   them   off   by  
pressing

  the   switch   on   the   dashboard.releasing
Pull the lever and press the button to
lower  the   parking   brake   lever.
driving safely

Page 114 of 276

11 2
Berlingo_2_VP_en_Chap05_Securite_ed02-2014
This dSc mode is calibrated for  a   low   level   of   skidding,  
based on dif

ferent conditions
of grip encountered on the
road.
When the ignition is switched off,
the
 
system   returns   automatically   to  
DSC

 
mode. This
d S c OFF   mode   is  
only

  suitable   for   specific  
conditions encountered


when
  moving   off   or   at   low  
speed.
Above

 
30
  mph   (50   km/h)   the   system  
returns

 
to
  DSC   mode   automatically. This
snow   mode   allows   the  vehicle to adapts its strategy
to the conditions of grip
encountered for each of the
two
  front   wheels,   on   moving  
of

f.
When
  moving,   the   system   optimises  
wheelspin to provide the best
acceleration possible for the grip
available.This

off-road   mode   (mud,  
wet

  grass...)   allows,   when  
moving

  off,   considerable  
wheelspin on the wheel
with the least grip to favour
clearing

  of   the   mud   and   regain   "grip".  
At

  the   same   time,   the   wheel   with   the  
most

  grip   is   controlled   in   such   a   way   as  
to

  transmit   as   much   torque   as   possible.
When
  moving,   the   system   optimises  
wheelspin

  to   meet   the   driver's  
requirements

  as   fully   as   possible.This sand
  mode   allows   a  little wheelspin on the two
driving
  wheels   at   the   same  
time

  to   allow   the   vehicle   to  
move

  forward   and   reduces  
the

  risk   of   getting   stuck   in   the   sand.
Do
  not   use   the   other   modes   on   sand  
as

  the   vehicle   may   become   stuck.
driving safely

Page 116 of 276

11 4
Berlingo_2_VP_en_Chap05_Securite_ed02-2014
recommendations for children:
-
use a suitable child seat if the
passenger is less than 12 years old
or

  shorter   than   one   metre   fifty,
-

never allow a child to travel on
your lap, even with the seat belt
fastened. For

  more   information   on   child  
seats, refer to the "Children on
board"

  section   of   chapter   5.
Clean the seat belt straps with
soapy water or a textile cleaning
product, sold by CITR
o Ë n
dealers.
In accordance with current safety
regulations, your CITR
o Ë n dealer can
guarantee
  all   work   or   any   checks,   from  
testing

  to   maintenance,   on   your   seat  
belt

  equipment.
Have
  the   seat   belts   checked   regularly  
(even

  after   a   minor   impact)   by   a  
CITROËN

  dealer   or   a   qualified  
workshop:

  they   must   not   show   any  
signs of wear

, cutting or fraying
and
  they   must   not   be   converted   or  
modified.
The

 
force
 
limiter
 
reduces
 
the
 
pressure
 of the seat belt against the body of the
occupants.
The pretensioning seat belts are active
when
 
the
 
ignition
 
is
 
switched
 
on.
The
 
inertia
 
reels
 
are
 
fitted
 
with
 
a
 
device
 
which

 
automatically
 
locks
 
the
 
strap
 
in
 
the

 
event
 
of
 
a
 
collision
 
or
 
emergency
 
braking

 
or
 
if
 
the
 
vehicle
 
rolls
 
over.
You can unfasten the seat belt by
pressing
 
the
 
red
 
button
 
on
 
the
 
buckle.
 
Guide

 
the
 
seat
 
belt
 
after
 
unfastening.
The
 
airbag
 
warning
 
lamp
 
comes
 
on
 
if

 
the
 
pretensioners
 
are
 
deployed.
 
Contact a CITR

o
Ë
n
dealer or a
qualified
 
workshop.
In
 
order
 
to
 
be
 
effective,
 
a
 
seat
 
belt:
-
 
must

 
restrain
 
one
 
person
 
only,
-
 
must

 
not
 
be
 
twisted,
 
check
 
by
 
pullin

g in front of you with an even
movement,
-
 
must

 
be
 
tightened
 
as
 
close
 
to
 
the
 
body

 
as
 
possible.
The upper part of the seat belt should
be positioned in the hollow of the
shoulder.
The lap part should be placed as low
as
 
possible
 
on
 
the
 
pelvis.
d

o not interchange the seat belt
buckles
 
as
 
they
 
will
 
not
 
fulfil
 
their
 
role
 
completely

.
 
If
 
the
 
seats
 
are
 
fitted
 
with
 
armrests,

 
the
 
lap
 
part
 
of
 
the
 
seat
 
belt
 
should

 
always
 
pass
 
under
 
the
 
armrest.
Check
 
that
 
the
 
seat
 
belt
 
is
 
fastened
 
correctly

 
by
 
pulling
 
the
 
strap
 
firmly.Front seat belts
The front seats are fitted with pretensioners   and   force   limiters.
rear seat belts
(5 seat version)
The rear seats are fitted with three-
point   inertia   reel   seat   belts.
Seat belts

Page 119 of 276

 117
Berlingo_2_VP_en_Chap05_Securite_ed02-2014
Good practice
Sit in a normal upright position.
W ear   a   correctly   adjusted   seat   belt.
d

o not leave anything between the
occupants and the airbags (a child,
pet,
  object...).  
This
  could   hinder   the  
operation

  of   the   airbags   or   injure   the  
occupants.
a

fter an accident or if the vehicle has
been
  stolen   or   broken   into,   have   the  
airbag

  systems   checked.
All
  work   on   the   airbag   system   is   strictly  
forbidden unless it is carried out by
qualified

  personnel   at   a   CITROËN  
dealer

  or   a   qualified   workshop.
Even if all of the precautions
mentioned
  are   observed,   a   risk   of  
injury

  or   of   minor   burns   to   the   head,  
chest

  or   arms   when   an   airbag   is  
deployed

  cannot   be   ruled   out.   In   fact,  
the

  bag   inflates   almost   instantly   (within  
a

  few   milliseconds)   then   deflates   within  
the

  same   time   discharging   the   hot   gas  
via

  openings   provided   for   this   purpose.Lateral airbags
Only
  put   recommended   covers   on  
the

  seats.  
These
  will   not   hinder  
inflation

  of   the   lateral   airbags.   Contact  
a

  CITROËN   dealer   or   a   qualified  
workshop.
Do

  not   fix   or   attach   anything   to   the   seat  
backs.

 
This
  could   cause   injury   to   the  
chest

  or   arms   when   the   lateral   airbag  
inflates.
d

o not sit with the upper part of the
body any nearer to the door than
necessary.
Front airbags
d

o not drive holding the steering wheel
by
  its   spokes   or   resting   your   hands   on  
the

  centre   part   of   the   wheel.
d

o not allow passengers to place
their
  feet   on   the   dashboard,   they   risk  
serious

  injury   if   the   airbag   is   deployed.
Smoke
  as   little   as   possible   as  
deployment

  of   the   airbags   can   cause  
burns

  or   the   risk   of   injury   from   a  
cigarette

  or   pipe.
Never
  remove   or   pierce   the   steering  
wheel

  or   hit   it   violently.
Airbags only operate when the
ignition is switched on.
This
 
equipment
 
only
 
operates
 
once.
 
If

 
a
 
second
 
impact
 
occurs
 
(during
 
the
 
same

 
or
 
a
 
subsequent
 
accident),
 
the
 
airbag

 
will
 
not
 
operate.
The
 
deployment

 
of

 
an

 
airbag

 
or

 
airbags

 
is

 
accompanied
 
by
 
a
 
slight
 
discharge
 
of

 
smoke
 
and
 
a
 
noise,
 
due
 
to
 
the
 
activation of the pyrotechnic cartridge
incorporated

 
in
 
the
 
system.
This
 
smoke
 
is
 
not
 
harmful,
 
but
 
sensitive

 
individuals
 
may
 
experience
 
some

 
irritation.
The
 
noise
 
of
 
the
 
detonation
 
may
 
result
 
in a slight loss of hearing for a short
time. The

 
passenger's
 
front
 
airbag
 
must
 
be deactivated if a child seat is
installed

 
facing
 
rearward.
Chapter 5, "Children on board"
section.
airbags
SaFETY
5

Page 121 of 276

 119
Berlingo_2_VP_en_Chap05_Securite_ed02-2014
Front airbags
The front airbags are fitted in the centre of the steering wheel for the
driver and in the dashboard for the
front  passenger.
d

eployment
They are deployed, except the
passenger's front airbag if it has been
deactivated, in the event of a serious
front
  impact   applied   to   all   or   part   of   the  
front

  impact   zone   A in the longitudinal
centreline of the vehicle on a horizontal
plane
  directed   from   the   front   towards  
the

  rear   of   the   vehicle.
The
  front   airbag   inflates   between   the  
front occupant of the vehicle and the
dashboard to cushion their forward
movement.
d
eactivationo
nly the passenger's front airbag can
be   deactivated:
-

with the ignition switched off
,
insert
  the   key   into   the   passenger's  
front airbag deactivation switch,
-


turn it to the of
f "OFF" position,
-
 
then
  remove   the   key,   keeping   the  
switch

  in   the   new   position.
The passenger's front
airbag
  warning   lamp   in   the  
instrument

  panel   is   on   while  
the

  airbag   is   deactivated.If
  the   two   airbag   warning   lamps  
are on continuously

, do not install
a rear-facing child seat, contact
a
  CITROËN   dealer   or   a   qualified  
workshop.
Front airbag fault
T
o ensure the safety of your child,
it is essential to deactivate the
passenger's front airbag when you
install a rear-facing child seat on the
front
  passenger   seat.   Otherwise,   the  
child

 
would
 
risk
 
being
 
kille
d  
or
 
seriously
 
injured

  if   the   airbag   were   to   inflate.
r
eactivation
In the "OFF" position, the passenger's
front airbag will not be deployed in the
event   of   an   impact.
As   soon   as   the   child   seat   is   removed,  
turn the airbag switch to the

"O n "
position to re-activate the passenger's
front airbag and so ensure the safety
of your passenger in the event of an
impact.
If   this   warning   lamp   comes  on,
  accompanied   by   an  
audible

  signal   and   a   message  
in the screen, contact a
CITR

o Ë n dealer or a
qualified
  workshop   to   have  
the

  system   checked.
airbags
SaFETY
5

Page 136 of 276

134
Berlingo_2_VP_en_Chap05_Securite_ed02-2014
cHILd LOcK
This prevents opening of the side
doors  from   the   inside.
Manual mode
a label indicates the location of the
child

  lock.
-
o pen fully past the point of
resistance.
-

T
ilt the lever, located on the rear
section
  of   the   door. Electric mode
With the ignition on, press this
button.  
The
  LED   comes   on.
 W

arning:   this   system   is  
independent of the central
locking

  control.
Always   remove   the   ignition   key  
when leaving the vehicle, even for
a

  short   time.
It   is   advisable   to   check   the   activation   of  
the

  child   lock   each   time   the   ignition   is  switched
  on.
In   the   event   of   a   serious   impact   the  electric
  child   lock   is   deactivated  
automatically

.
Child safety

Page 146 of 276

Berlingo_2_VP_en_Chap07_Verification_ed02-2014
144
cooling system
Only use the fluid recommended by the manufacturer.
Otherwise,
  you   risk   seriously   damaging  
your

  engine.
When
  the   engine   is   warm,   the  
temperature

  of   the   coolant   is   controlled  
by

  the   engine   fan.  
As
  this   fan   can  
operate

  with   the   ignition   key   removed  
and

  because   the   cooling   system   is  
pressurised, wait for at least one hour
after the engine has stopped before
carrying

  out   any   work.
Slacken
  the   cap   by   1/4   of   a   turn   to  
release the pressure to prevent any
risk

  of   scalding.   When   the   pressure  
has

  dropped,   remove   the   cap   and   top  
up

  the   level   with   coolant.
If
  fluid   has   to   be   added   frequently,  
this

  indicates   a   fault   which   must   be  
checked

  by   a   CITROËN   dealer   as  
soon

  as   possible.
Power steering fluid level
The vehicle must be parked on level ground  with   the   engine   cold.   Unscrew  
the cap integrated with the gauge and
check

  the   level   which   must   be   between  
the

  MIN   and   MAX   marks. In
  order   to   regenerate   the   filter,   you  are advised to drive at a speed higher
than
  40   mph   (60   km/h)   for   at   least   five  minutes
  as   soon   as   possible,   when  
traffic

  conditions   permit   (until   the  
message

  disappears   and   the   service  
warning

  lamp   goes   off).
d

uring regeneration of the particle
emission
  filter,   the   noise   of   a   relay  
operating

  may   be   heard   under   the  
dashboard.
If

  the   message   is   still   displayed   and  
if

  the   service   warning   lamp   remains  
on, contact a CITR

o Ë n dealer or a
qualified
  workshop.
topping up
The

 
level
 
must
 
be
 
between
 
the
 
MIN
 
and

 
MAX
 
marks
 
on
 
the
 
expansion
 
bottle.

 
If
 
more
 
than
 
1
 
litre
 
of
 
fluid
 
is
 
required

 
to
 
top
 
up
 
the
 
level,
 
have
 
the
 
system

 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or

 
a
 
qualified
 
workshop.
Screenwash and headlamp
wash level
For best quality cleaning and for your safety , we would advise that you use
products
  of   the   CITROËN   range.
For
  optimum   cleaning   and   to   avoid  
freezing,

  this   fluid   must   not   be   topped  
up

  or   replaced   with   plain   water.
Capacity
  of   the   screenwash   reservoir:  
approximately

  3   litres.
If
  your   vehicle   is   fitted   with   headlamp  
washers, the capacity of the reservoir
is

  6   litres.
diesel additive level
( d iesel with particle
emission filter)
topping up
This   additive   must   be   topped   up   by  
a

  CITROËN   dealer   or   a   qualified  
workshop

  without   delay.
Waste products
avoid prolonged contact of used oil
with   the   skin.
Brake
  fluid   is   harmful   to   health   and  
very

  corrosive.
Do
  not   dispose   of   used   oil,   brake   fluid  
or coolant into drains or into the ground
but into the containers dedicated to this
use at a CITR

o Ë n dealer (France) or
an
  authorised   waste   disposal   site.
The
 
minimum
 
level
 
of
 
this
 
additive
 
is indicated by lighting of the service
warning

 
lamp,
 
accompanied
 
by
 
an
 
audible

 
signal
 
and
 
a
 
message
 
in
 
the
 
screen.
When this occurs with the engine
running it is due to the start of
saturation

 
of
 
the
 
particle
 
emission
 
filter
 
(exceptionally prolonged urban type
driving

 
conditions:
 
low
 
speed,
 
long
 
traffic

 
jams,
 
...).
Levels

Page 150 of 276

DIESEL
Berlingo_2_VP_en_Chap07_Verification_ed02-2014
148
FuEL cut-OFF
In a serious collision, a mechanism automatically  prevents   fuel   from  
reaching

  the   engine.
The
  flashing   of   this   warning  
lamp

  is   accompanied   by   a  
message

  in   the   screen.
Check
  that   there   is   no   odour   or  
leakage

  of   fuel   outside   the   vehicle   and  
re-establish

  the   fuel   supply:
-
switch of

f the ignition (ST
o
P position),
-
 
remove
  the   key,
-
 
put
  the   key   back   in   the   ignition,
-
 
switch
  on   the   ignition   and   start.
dIESEL PrIMInG PuMP
If you should run out of fuel, it is
necessary  to   prime   the   fuel   circuit:
-
 
fill
  the   fuel   tank   with   at   least   five  
litres of

d iesel,
-
 
squeeze
  and   release   the   manual  
priming

  pump,   under   the   bonnet  
under the protective cover

,
-

operate the starter until the engine
starts. Refer

  to   chapter   7:   "Under   the  
bonnet"

  section.
Fuel used for diesel
engines
The Diesel  engines  are  compatible  with  biofuels
  which   conform   to   current   and  
future European standards (

d iesel fuel
which
  complies   with   standard   EN   590  
mixed

  with   a   biofuel   which   complies  
with standard E

n 14214) available at
the
  pumps   (containing   up   to   7   %   Fatty  
Acid

  Methyl   Ester).
The B30 biofuel can be used in certain
d

iesel engines; however, this use
is
  subject   to   strict   application   of   the  
special servicing conditions indicated
in

  the   maintenance   and   warranty  
guide.

  Contact   a   CITROËN   dealer   or   a  
qualified

  workshop.
The use of any other type of (bio)
fuel
  (vegetable   or   animal   oils,   pure  
or

  diluted,   domestic   fuel...)   is   strictly  
prohibited

  (risk   of   damage   to   the  
engine

  and   fuel   system).
Fuel

Page 152 of 276

Berlingo_2_VP_en_Chap07_Verification_ed02-2014
150
range indicators
When switching on the ignition, an
indicator  gives   an   estimate   of   the  
distance that can be travelled with
your vehicle before engine starting
is

  automatically   prevented,   once   the  
vehicle starts using the reserve of a

dBlue
® or after a fault is detected with
the
 
SCR   system.
In
 
the
 
event   of   simultaneous   system  
fault and low a

dBlue
® level, the
shortest
 
range
 
is
 
the
 
one   displayed.
In the event of the risk
of non-starting related to a lack
of AdBlue
®
The engine start prevention
system   required   by   regulations   is  
activated

  automatically   once   the  
a
dBlue
® tank is empty.
range greater than 1 500 miles (2 400 km)
When the ignition is switched on, no
information   on   range   is   displayed  
automatically

  in   the   instrument   panel.
Pressing this button
displays the driving range
temporarily.
Above
  3   000   miles  
(5
  000   km),   the   value   is  
not

  specified. When switching on the ignition, the
UREA warning
  lamp   comes   on,  
accompanied

  by   an   audible   signal   and  
the

  display   of   a   message   (e.g.:   "Top   up  
emissions

  additive:   Starting   prevented  
in

  900   miles")   indicating   the   remaining  
range

  expressed   in   miles   or   kilometres.
When
  driving,   the   message   is  
displayed

  every   150   miles   (300   km)  
until

  the   additive   tank   has   been  
topped-up.
Go

  to   a   CITROËN   dealer   or   a   qualified  
workshop

  to   have   the  
AdBlue® tank topped-up.
Y
ou
 
can
 
also
 
top-up
 
the
 
tank
 
yourself.
Refer
 
to
 
the
 
"Topping-up"
 
section.
r

emaining range between 350 and
1500 miles (600 and 2 400 km)
adBlue® additive

Page 153 of 276

Berlingo_2_VP_en_Chap07_Verification_ed02-2014
151
When switching on the ignition, the
SERVICE  warning   lamp   comes   on  
and

  the   UREA
 
warning   lamp   flashes,  
accompanied

  by   an   audible   signal   and  
the

  display   of   a   message   (e.g.   "Top   up  
emissions

  additive:   Starting   prevented  
in

  350   miles")   indicating   the   remaining  
range

  expressed   in   miles   or   kilometres.
When
  driving,   the   message   is  
displayed every 30 seconds until the
additive

  tank   has   been   topped-up.
Go
  to   a   CITROËN   dealer   or   a   qualified  
workshop

  to   have   the  
AdBlue® tank topped-up.
Y
ou
 
can
 
also
 
top-up
 
the
 
tank
 
yourself.
Refer
 
to
 
the
 
"Topping-up"
 
section.
o

therwise you will not be able to
restart
 
your
 
engine. When switching on the ignition, the
SERVICE
  warning   lamp   comes   on  
and

  the   UREA
 
warning   lamp   flashes,  
accompanied

  by   an   audible   signal  
and

  the   display   of   the   message  
"T

op   up   emissions   additive:   Starting  
prevented".
The

a dBlue
® tank is empty: the system required
 
by
 
regulations   prevents  
engine

 
starting. To be able to start the engine,
we
  recommend   that   you   call   on  
a

  CITROËN   dealer   or   a   qualified  
workshop

  for   the   top-up   required.   If  
you carry out the top-up yourself, it is
essential

  to   add   at   least   3.8   litres   of  
a dBlue
® to the tank.
r

emaining range between 0 and
350 miles (0 and 600 km) Breakdown related to a lack of
AdBlue
® additive
Refer   to   the   "Topping-up"   section.
adBlue® additive
CHECkS
7

Page:   < prev 1-10 11-20 21-30 31-40 41-50 51-60 next >