fold seats Citroen BERLINGO MULTISPACE RHD 2014.5 2.G Owner's Manual

Berlingo_2_VP_en_Chap04_Ergonomie_ed02-2014
70
never drive with the head
restraints   removed;   they   must   be  
in

  place   and   correctly   adjusted.Adjustable armrest
To access the vertical position, raise
the
  armrest   until   it   locks.
Lower   the   armrest   to   return   it   to   a  
position

  for   use.
To   remove   the   armrest,   press   the  
release

 
button
 
from
 
the
 
vertical
 
position
 
and

  move   aside   the   armrest.
To   put   the   armrest   back   in   place,   clip   it  
in

  the   vertical   position.
If   the   vehicle   is   fitted   with   the   additional  
console

  and   an   armrest,   to   fold   the  
passenger seat to the table position
remove

  the   console   or   the   armrest.
Front heated seats control
Each front seat may be fitted with a control located on the side part of the
cushion.
Press
  to   switch   on   the   cushion   heating.
Press
  again   to   switch   it   off.
Head restraint height adjustment
To raise the head restraint, slide it vertically
upwards.
To lower the head restraint, press the
button and slide the head restraint
vertically
  downwards.
The
  adjustment   is   correct   when   the   upper
 edge of the head restraint is level with the


top
  of   the   head.
To
  remove   the   head   restraint,   press   the
 button

  and   pull   the   head   restraint   upwards.
To re-install the head restraint, engage
the
  rods   in   the   holes   making   sure   they   are
 aligned

  with   the   seat   back.
Seats

Berlingo_2_VP_en_Chap04_Ergonomie_ed02-2014
 71
rEAr BEncH SEAt
Each 1/3 - 2/3 section can be folded fully,   then   removed   individually.
Head restraint
High position: lift and raise the head restraint.
Low
  position:   press   on   the   head  
restraint

  to   lower   it.
To
  remove   the   head   restraint,   after  
raising it press the tab and lift the head
restraint.
T

o install the head restraint, engage
the rods of the head restraint in the
holes
  keeping   it   in   line   with   the   seat  
back.
The

 
1/3
 
-
 
2/3
 
rear
 
bench
 
seat
 
is
 
fitted
 
with

 
"comma"
 
shape
 
head
 
restraints.
Seats
EASE OF uSE and cOMFOrt
4

Berlingo_2_VP_en_Chap04_Ergonomie_ed02-2014
72
Fully folded position
Example of operations for the 1/3 section. They   are   identical   for  
the 2/3

  section.
-

Place the head restraints in the low
position.
-

 
If
  necessary,   move   the   front   seats  
forward.
-


Press the grey control located on
the

  upper   part   of   the   seat   back.
-
 
Fold
  the   seat   back   onto   the   seat  
cushion. -


Raise the grey control bar
, located
at   the   rear   of   the   seat   cushion.
-  
T
ilt   the   entire   seat   forward.
Putting back in place
Tilt the entire seat rearwards until it
locks.
Raise  the   seat   back.
The
  seat   is   locked   correctly   when   the  
control

  (at   the   top   of   the   seat   back)   is  
no

  longer   visible.
Check
  that   the   seat   is   locked  
on

  the   floor   securely   when   it   is  
returned

  to   the   sitting   position.
Seats

Berlingo_2_VP_en_Chap04_Ergonomie_ed02-2014
 73
removing the bench seat
- If  necessary,   move   the   front   seats  forward.
-
 
Place
  the   bench   seat   (1/3   section  
and/or

  2/3   section)   in   the   fully  
folded

  position.
refitting the bench seat
- Offer up  the  bench  seat  (1/3  section  and/or
  2/3   section)   vertically.
-
 
Place
  the   hooks   between   the   two  
bars.
-

 
Fold
  the   bench   seat   rearwards.
Refer to the "fully folded position"
described
 
on
 
the
 
previous
 
page. To return the bench seat
(1/3 section
  and/or   2/3   section)  
to the "passenger transportation"
position, refer to the "fully folded
position" described on the previous
page.
-


T

ilt the entire seat rearwards by
approximately
 
45°.
-

Lift the bench seat

vertically to the
limit
 
of
 
the
 
anchorages.
-

Straighten bench seat by tilting it
forwards

 
then
 
lift
 
it.
Seats
EASE OF uSE and cOMFOrt
4

Berlingo_2_VP_en_Chap04_Ergonomie_ed02-2014
74
rEAr SEAtS (5 SEAt VE r SIO n) Head restraint
High position: lift and raise the head restraint.
Low
  position:   press   on   the   head  
restraint

  to   lower   it.
To
  remove   the   head   restraint,   after  
raising it press the tab and lift the head
restraint.
T

o install the head restraint, engage
the rods of the head restraint in the
holes
  keeping   it   in   line   with   the   seat  
back.
Each

 
seat
 
can
 
be
 
removed
 
individually.
Each
 
time
 
a
 
seat
 
is
 
returned
 
to
 
the
 
sitting

 
position
 
or
 
after
 
removing
 
then
 
refitting

 
a
 
seat,
 
check
 
that
 
it
 
is
 
locked
 
on

 
the
 
floor
 
securely.
The three independent rear seats
are
 
fitted
 
with
 
"comma"
 
shape
 
head
 
restraints.
The

 
back
 
of
 
the
 
centre
 
seat,
 
folded
 
onto the seat cushion, has a shell
which serves as a table with cup
holder

.
Seats

Berlingo_2_VP_en_Chap04_Ergonomie_ed02-2014
 75
Adjusting the angle of the seat back
- Operate  the   control   and   adjust   the  angle
  of   the   seat   back.
Placing the seat back in the
table position
- Pull  the   control   to   fold   the   seat   back  onto
  the   seat   cushion.
Do
  not   place   hard   or   heavy   objects  
on

  the   table.  
They
  could   become  
dangerous

  projectiles   in   the   event   of  
sharp

  braking   or   impact.
returning the seat back to the
sitting position
- Release   the   seat   back   by   pulling  the control, then return it to its
original
  position.
When returning the seat back to the sitting position,  ensure   that   it   is   locked   securely.
Placing the seat in the fully
folded position
- Pull the control to place the seat
back  in   the   table   position.
-

Raise the bar located behind the
seat to release the rear anchoring
points.
-


T
ilt the entire seat forwards, until it
locks.
returning the seat to its original
position
- Push   the   red   control.
-  
Fold
  back   the   seat   to   fix   the   rear  
anchoring

  points.
-
 
Raise
  the   seat   back   by   pulling   the  
control.
Check

  that   the   entire   seat   is   anchored  
securely

.
Seats
EASE OF uSE and cOMFOrt
4

Berlingo_2_VP_en_Chap04_Ergonomie_ed02-2014
76
removing the seat
- If  necessary,   move   the   front  seats forward and lower the head
restraint.
-

Place the seat in the fully folded
position.
Good practice
Following the various operations:
-  
do
  not   remove   a   head   restraint  
without

  storing   it   and   fix   it   to   a  
support,
-


ensure that the passengers can
always access the seat belts and
fasten

  them   easily,
-
 
passengers
  must   never   take  
their

  seat   without   adjusting   and  
fastening

  their   seat   belt.
Refer to the "fully folded position"
described
 
on
 
the
 
previous
 
page.
-

Press the red lever to release the
front

 
feet.
-

T

ilt the entire seat rearwards by
approximately
 
45°
 
without
 
releasing
 
the

 
lever.
-
 
Release

 
the
 
lever.
-

Lift the seat

vertically
 
to
 
the
 
limit
 
of
 
the

 
anchorages.
-

Straighten the seat by tilting it
forwards

 
then
 
lift
 
it.
Putting the seat back in place
- Tilt   the   seat   forward   by   45°.
-  
Place
  the   hooks   between   the   two  
bars.
-

 
Fold
  back   the   seat   to   fix   the   rear  
anchoring

  points.
-

Pull the control to return the seat
back

  to   its   initial   position.
-
 
Raise
  the   head   restraint.
Check
  that   no   object   is   obstructing  
the anchoring recesses or preventing
correct

  locking   of   the   seats.
Seats

Berlingo_2_VP_en_Chap04_Ergonomie_ed02-2014
 79
Adjusting the angle of the seat back
- 
Operate
  the   control   and   adjust   the  
angle.
Placing the seat in the table position
-

 
Lower
  the   head   restraint   fully.
-
o perate the control to fold the seat
back
  onto   the   seat   cushion.
r
eturning the seat back to the
sitting position
-  
Release
  the   seat   back   by   pulling  
the control, then return it to its
original

  position.
Ensure that the entire seat is anchored
securely.
Placing the seat in the fully folded
position
-  
Place
  the   seat   in   the   table   position.
-

Pull the red strap, located behind
the seat, to release the feet of the
seat

  from   their   anchorage   on   the  
floor

.
-
 
T
ilt   the   entire   seat   forwards.
row 2 seat adjustmentsreturning the seat to its original
position
-
 
Fold
  back   the   entire   seat.
Before folding the seat, ensure
that:
-

in row 3, no passenger's
foot is at one of the seat
anchorages

  on   the   floor,
-
 
the
  seat   is   locked   securely   on  
the

  floor,
-

the seat belt is available for
the

  passenger.
Seats
EASE OF uSE and cOMFOrt
4

Berlingo_2_VP_en_Chap04_Ergonomie_ed02-2014
80
row 3 seat adjustments
Placing the seat back in the table
position
- 
Lower
  the   head   restraint   fully.
-
o perate the control to fold the seat
back
  onto   the   seat   cushion.
r

eturning the seat back to the
sitting position
-
 
Release
  the   seat   back   by   pulling  
the control, then return it to its
original

  position.
Ensure that the entire seat is anchored
securely.r eturning the seat to its original
position
-
 
Push
  the   red   control.
-
 
Fold
  back   the   entire   seat.
Placing the seat in the fully folded
position
-
 
Place
  the   seat   in   the   table   position.
-
 
Raise
  the   bar   fitted   with   a   red  
strap, located behind the seat, to
release

  feet   of   the   seat   from   their  
anchorage

  on   the   floor.
-
 
T
ilt   the   entire   seat   forwards.Ensure
  that:
-
 
the
  seat   is   locked   securely   on  
the

  floor,
-

the seat belt is available for
the

  passenger.
Seats

Berlingo_2_VP_en_Chap04_Ergonomie_ed02-2014
81
Entering, exiting from row 3
Entering
-
Place the row 2 seat in the table
position.
Exiting
-

 
Lower
  the   head   restraint   fully.
-
o perate the yellow control, located
on
  the   back   of   the   row   2   seat   back.
-
 
Fold
  the   seat   back   to   the   table  
position.Ensure that the stored centre
seat belt is placed correctly in its
strengthener

  in   the   headlining.
-

T
ilt it to the fully folded position to
allow
  access. -

Pull the red strap to place the seat
in

  the   fully   folded   position.
-  T ilt   the   entire   seat   forwards.
-  
Exit
  via   the   side   door.
Before
  folding   it   back,   ensure   that  
the feet of the passenger in row 3
are not obstructing the row 2 seat
anchoring

  points.
Seats
EaSE oF USE and CoMFoRT
4