tow bar Citroen BERLINGO MULTISPACE RHD 2014.5 2.G Owner's Manual

Berlingo_2_VP_en_Chap04_Ergonomie_ed02-2014
83
Handling the row 3 seat
removing the seat
-  
Lower
  the   head   restraint.
-

Place the seat in the fully folded
position.
-

 
T
ilt   the   entire   seat   forwards.
-
 
On
  each   side,   take   hold   of   the  
uprights of the folded seat, tilting it
forward

  slightly,   and   lift   it.r epositioning the seat
The label on the seat indicates the
position
  in   which   it   must   be   installed.
-
 
Place
  the   hooks   of   the   front   feet  
between

  the   two   bars.
-
 
Ensure
  that   no   object   or   foot   is  
obstructing the rear anchoring
recesses and that the seat belt is
positioned

  correctly   and   available.
-
 
Fold
  back   the   seat   to   fix   its   rear  
anchoring

  feet.
-
o perate the control to raise the
seat
  back   to   its   initial   position.
-
 
Raise
  the   head   restraint.
Good practice
Do not place hard or heavy objects on the  seat   backs   forming   a   table,   they  
could

  become   dangerous   projectiles   in  
the

  event   or   sharp   braking   or   impact.
Following
  the   various   operations:
-
 
do
  not   remove   a   head   restraint  
without stowing it; secure it inside
the vehicle,
-


ensure that the passengers can
always access the seat belts and
fasten

  them   easily,
-
 
passengers
  must   never   take  
their

  seat   without   adjusting   and  
fastening their seat belt,
-

 
a
  passenger   seated   in   row   3   must  
ensure that he does not obstruct
the row 2 seat anchoring recesses,
-

 
a
  passenger   seated   in   row   3   must  
not

  have   the   seat   in   front   of   them   in  
row 2 in the folded position; this is
in case the seat should tip towards
the passenger unexpectedly and
injure

  them.
Seats
EaSE oF USE and CoMFoRT
4

Berlingo_2_VP_en_Chap04_Ergonomie_ed02-2014
94
MOdutOP rOOF BA r S
The maximum authorised weight on each
  roof   bar   is   35   kg. In
  all   cases,   the   load   must   rest   on  
the non-slip bands provided for this
purpose

  and   must   not   touch   the   roof   or  
the

  glazing   of   the   roof.
r
ecommendations for loading
the roof
This   procedure   requires   the   use   of  
a spanner supplied with the tools for
changing

  a   wheel.
These two longitudinal Modutop roof
bars   can   be   removed.
Chapter   9,   "Changing   a   wheel"  section.
-
 
Open
  the   protective   covers.
-
 
Slacken
  the   four   screws   using   the  
spanner

  and   remove   them.
-
 
T
urn   the   bars   90°   placing   the  
hollow

  parts   towards   the   front.
-
 
Refit
  the   the   4   screws   and   tighten  
them

  using   the   spanner.
-
 
Close
  the   protective   covers.
-

Use the strap passages
A only to
secure
  the   load   firmly.
Practical information

Berlingo_2_VP_en_Chap04_Ergonomie_ed02-2014
98
12 Volt socket (120 W Max)
It is advisable to limit the use of this socket  to   avoid   discharging   the   battery.
Protective net
Open the cover located in the hook support.
Fix the top of the net in the notches,
having
  first   turned   the   bar   1/4   of   a   turn.
Ensure that the end of the bar engages
correctly
  in   the   metal   part   of   its  
location.
Fix the straps in the locations provided
on

  the   floor.
Tighten
  the   net   using   the   straps.
Stowing rings
Use these rings to secure loads on the
floor.
Practical information

108
Berlingo_2_VP_en_Chap05_Securite_ed02-2014
Activation / deactivationMalfunction
In the event of a malfunction, when reverse gear is engaged the LE
d in the
button
  comes   on,   accompanied   by   an  
audible

  signal   and   a   message   in   the  
screen.

  Contact   a   CITROËN   dealer   or  
a

  qualified   workshop.
Good practice
In bad weather or in winter, ensure that
the  sensors   are   not   covered   with   mud,  
ice

  or   snow.
The
  system   will   be   deactivated  
automatically

  if   a   trailer   is   being   towed  
or

  if   a   bicycle   carrier   is   fitted   (vehicle  
fitted

  with   a   towbar   or   bicycle   carrier  
recommended

  by   CITROËN).
The
  parking   assistance   cannot,   in  
any

  circumstances,   take   the   place   of  
the vigilance and responsibility of the
driver

.
You can activate or deactivate
the
 
system
 
by
 
pressing
 
this
 
button.
The activation or deactivation
of

 
the
 
system
 
is
 
stored
 
when
 
the

 
vehicle
 
stops.
Parking sensors

136
Berlingo_2_VP_en_Chap06_Accessoire_ed02-2014
Good Practice
In certain cases of particularly arduous
use  (towing   the   maximum   load   up   a  
steep

  slope   in   high   temperatures),   the  
engine

  automatically   limits   its   power.  
In this case,

the air conditioning is
automatically
  cut   off   to   save   engine  
power

.
tyres
Check

  the   tyre   pressures   of   the   towing  
vehicle and of the trailer

, observing the
recommended
  pressures.
Chapter
  7,   "Levels"   section.
If
  the   coolant   temperature  
warning

  lamp   comes   on,   stop  
the vehicle and switch of

f the
engine
  as   soon   as   possible.Brakes
Towing
  increases   the   braking   distance.  Drive
  at   a   moderate   speed,   change  
down

  early   and   brake   gradually.
towbar
We recommend the use of genuine CITRo Ë n towbars and their
harnesses, which have been tested
and
  approved   from   the   design   stage   of  
your vehicle, and that you entrust the
fitting

  of   this   equipment   to   a   CITROËN  
dealer

.
If
  this   equipment   is   not   fitted   by   a  
CITROËN

  dealer,   it   is   imperative   that  
it

  is   fitted   using   the   electrical   pre-
equipment
  installed   at   the   rear   of   the  
vehicle and in accordance with the
manufacturer's

  instructions.
In accordance with the general
instructions
  a   reminder   of   which   has  
been given above, we draw your
attention

  to   the   risk   associated   with  
fitting

  a   towbar   or   electrical   accessory  
not

  recommended   by   CITROËN.  
Fitting

  such   equipment   could   result   in  
the failure of your vehicle's electronic
system.

  Please   obtain   information   from  
the

  Manufacturer   before   fitting   this   type  
of

  equipment.
Side wind
Sensitivity
 
to
 
side
 
wind
 
is
 
increased.
 
Drive

 
smoothly
 
and
 
at
 
a
 
moderate
 
speed.
ABS/

d
S
c
The

 
ABS

 
or
 
DSC
 
systems
 
only
 
control
 
the

 
vehicle,
 
not
 
the
 
trailer
 
or
 
caravan.
Parking sensors
The
 
rear
 
parking
 
sensors
 
system
 
does
 
not

 
function
 
while
 
the
 
vehicle
 
is
 
towing.
Chapter
 
9,
 
"Identification
 
markings"

 
section.
towing a trailer

Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
160
1. Parking the vehicle
- The  occupants   must   get   out   of   the  vehicle
  and   wait   in   a   safe   location.
-
 
If
  possible,   park   the   vehicle   on  
level, stable and non-slippery
ground.
-

 
Apply
  the   parking   brake,   switch  
of

f   the   ignition   and   engage   first   or  
reverse

  gear. -
 Place   a   chock   under   the   wheel  diagonally opposite the one to be
changed.
cHAnGInG A WHEEL
2. t
ools
The tools are stowed in a storage area
closed  by   a   flap   under   a   front   seat.
-
 
If
  necessary,   move   the   seat   forward  
to

  access   the   storage   compartment  
from

  the   rear.
-
 
Remove
  the   flap   then   take   out   the  
jack

  and   the   tool   carrier.
-
 
Remove
  the   tools   needed   from   the  
carrier

.
1.
 
Jack.
2.

 
Wheelbrace.
3.

 
Chock.
4.


Spanner for the Modutop roof bars
and

  rear   lamps.
5.
 
Allow
  wheel   trim   removal   tool.
6.
 
T
owing   eye.
If
 
the
 
vehicle
 
is
 
fitted
 
with
 
a
 
towbar,
 
it

 
is
 
sometimes
 
necessary
 
to
 
raise
 
the

 
vehicle
 
slightly
 
to
 
make
 
it
 
easier
 
to

 
remove
 
the
 
spare
 
wheel
 
from
 
its
 
carrier

.
On
 
certain
 
types
 
of
 
ground
 
and/
or if considerable loads are being
transported, call a CITR
o
Ë
n
dealer or
a
 
qualified
 
workshop.
The
 
jack
 
and
 
tools
 
are
 
specific
 
to
 
your
 
vehicle.

 
Do
 
not
 
use
 
them
 
for
 
other
 
purposes.
Changing a wheel

Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
178
Without lifting (4 wheels on the
road)
You should always use a towing bar.
BEInG tOWEd
Ths procedure involves the use of the
towing eye supplied with the tools for
changing
  a   wheel.
From the front
- Unclip the cover by pressing the
bottom  part.
-
 
Fully
  screw   in   the   removable   towing  
eye.
From the rear
- Unclip the cover using a coin or the
flat  part   of   the   towing   eye.
-
 
Fully
  screw   in   the   removable   towing  
eye. When towing with the engine
switched

  off,   there   is   no   braking   or  
steering

  assistance.
Lifting (only 2 wheels on the
road)
It is preferable to raise the vehicle
using
  professional   lifting   equipment.
Vehicles fitted with a manual
gearbox (d iesel version)
In the case of vehicles fitted with a  manual   gearbox,   the   gear   lever  
must

  be   in   neutral,   failure   to   observe  
this

  special   condition   may   result   in  
damage

  to   transmission   and   braking  
components

  and   the   absence   of  
braking

  assistance   when   the   engine   is  
started

  again.
Chapter
 
9,
 
"Changing
 
a
 
wheel"
 
section.
Having your vehicle towed