Citroen BERLINGO MULTISPACE RHD 2015.5 2.G Owner's Guide

19
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
Good practice
Take care not to allow the remote control  to   come   into   contact   with  
grease,

  dust,   rain   or   a   damp  
environment.
A
 

heavy   object   attached   to   the   key  
(key

  ring,   ...)   weighing   on   the   shaft  
of

  the   key   in   the   switch,   may   cause   a  
malfunction.
REMOTE CONTROL
Reinitialising the remote control
Following changing of the remote control battery or disconnection of the
vehicle  battery,   the   remote   control   may  
have

  to   be   reinitialised.
Wait
  at   least   one   minute   before   using  
the

  remote   control.
Insert
  the   key   in   the   ignition   switch   with  
the

  buttons   (padlocks)   of   the   remote  
control

  facing   you.
Switch
  on   the   ignition.
Press
  the   locking   padlock   for   at  
least

  five   seconds   within   the   next  
ten seconds.
Switch

  off   the   ignition.
Wait
  at   least   one   minute   before   using  
the

  remote   control.
The
  remote   control   is   now   working  
again.
Use only identical batteries or
batteries of an equivalent type to
those

 
recommended
 
by
 
CITROËN
 
dealers.
Do

 
not
 
discard
 
the
 
remote
 
control
 
batteries,

 
they
 
contain
 
metals
 
which
 
are

 
harmful
 
to
 
the
 
environment.
Deposit
 
them
 
at
 
a
 
CITROËN
 
dealership, or at an authorised
collection

 
point.
Unfolding / folding
Changing the battery
Battery ref.: CR1620 / 3 volts.
The   "battery   flat"   information   is   given  
by

  an   audible   signal,   accompanied   by  
a

  message   in   the   screen.
To replace the battery, unclip the
casing
  using   a   coin   at   the   ring.
If
  the   remote   control   does   not   work  
after the battery has been changed,
reinitialise

  the   remote   control.
There
  is   a   risk   of   damage   if   the  
replacement

  battery   is   not   the   correct  
type.If you do not press the button,
you

  may   damage   the   key's  
folding

  mechanism.
access
REadY To Go
3

20
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
Don't forget
When  leaving   the   vehicle,   check   that  
the lighting is of

f and nothing of value
is
  visible.
a

s a safety precaution (with children
on
  board),   remove   the   key   from   the  
ignition when leaving the vehicle, even
for

  a   short   time.
Good practice
Do not make any modifications to the electronic  immobiliser   system.
Operating
  the   remote   control,   even  
when

  it   is   in   your   pocket,   may   result   in  
involuntary

  unlocking   of   the   doors.
The
  simultaneous   use   of   other  
high

  frequency   equipment   (mobile  
telephones,

  domestic   alarms…),   may  
interfere with the operation of the
remote

  control   temporarily.
The
  remote   control   does   not   operate  
while

  the   key   is   in   the   ignition,   even   if  
the

  ignition   is   off.
ELECTRONIC
IMMOBILISER
If you lose your keys
Visit a CITRo Ë n dealer with the
vehicle's
  V5   registration   certificate   and  
your

  identification   document.
a CITR

o Ë n dealer will be able
to
  retrieve   the   key   code   and  
the transponder code so that a
replacement

  key   can   be   ordered.When purchasing a second-hand
vehicle,
  have   the   keys   memorised   by  
a CITR

o Ë n dealer, so as to be sure
that   the   keys   in   your   possession   are  
the only ones that can be used to start
the

  vehicle.
ALARM
If fitted on your vehicle, this provides two
  types   of   protection:
-
 
exterior
  protection:   it   sounds   if   a  
front/rear

  door   or   the   bonnet   is  
opened.
-

 
interior
  protection:   it   sounds   if  
the

  volume   inside   the   passenger  
compartment

  changes   (breaking   of  
a

  window   or   a   movement   inside   the  
vehicle).
If

 
your
 
vehicle
 
is
 
fitted
 
with
 
a
 
separation
 
partition, the interior protection is not
active

  in   the   load   space.
Locking the vehicle with
complete alarm
Setting the alarm
- Switch off the ignition and get out of
the   vehicle.
-
 
Set
  the   alarm   within   five   minutes   of  
getting

  out   of   the   vehicle,   by   locking  
or

  deadlocking   using   the   remote  
control.

 
The
  red   LED,   located   in   the  
button,

  flashes   once   per   second.
All of the keys contain an electronic immobiliser  device.
This
  device   locks   the   engine   supply  
system.

  It   is   activated   automatically  
when

  the   key   is   removed   from   the  
ignition.
a

fter the ignition is switched on, a
dialogue
  is   established   between   the   key  
and

  the   electronic   immobiliser   system.
The
  metal   part   of   the   key   must   be  
unfolded correctly for correct dialogue
to

  take   place.
access

21
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
FRONT DOORS
From the inside
Use the door opening control to unlock and  open   the   door   concerned.
From the outside
Use the remote control to lock/unlock the  vehicle.
Insert
  the   metal   part   of   the   key   in   the  
lock

  on   the   driver's   side   if   the   remote  
control

  does   not   work.
Disarming
- Unlock  the   vehicle   with   the   remote  control or switch on the ignition, the
red
  LED   goes   off.
Locking the vehicle with
exterior protection only
If, while you are away from the vehicle, you wish to leave a window partially
open or a pet inside the vehicle, you
should
  choose   exterior   protection   only.
-
 
Switch
  off   the   ignition.
-

In the next ten seconds,
press the button until the
red 
LED
 
is
 
on
 
continuously
.
- Get  out   of   the   vehicle.
-  
Within
  the   next   five   minutes,   set  
the

  alarm   by   locking   or   deadlocking  
using

  the   remote   control   (the   red  
LED

  flashes   once   a   second).
Triggering
The siren sounds, the direction indicators
flash  for   approximately   30   seconds   and  
the

  red   LED   flashes   rapidly.
- To switch it off, insert the key and switch  on   the   ignition.
When
  the   alarm   has   been   triggered   ten  
times

 
in
 
succession
 
(when
 
triggered
 
for
 
the
 
eleventh

  time)   it   is   deactivated.   Repeat   the  
procedure

  for   setting   the   alarm.
Locking the vehicle without
alarm
- Insert  the   key   in   the   lock   on   the  driver's
  door   and   lock   it.
Do
  not   set   the   alarm   when   washing  
your

  vehicle.
Failure of the remote control
When the alarm is set but the remote control   does   not   operate:
-

Unlock the doors with the key and open   the   door.  The   alarm   is   triggered.
- Switch on the ignition in the
next  ten   seconds.  The   alarm   is  
disarmed.
Incorrect operation
When the ignition is switched on, if the
red  LED   remains   on   for   ten   seconds,  
there

  is   a   fault   in   the   siren   connection.
Contact a CITR
o Ë n dealer to have the
system
  checked.
Automatic setting of the alarm
depending on the country in which
the   vehicle   is   sold,   the   alarm   is   set  
automatically

  approximately   2   minutes  
after

  the   last   door   is   closed.
To
  prevent   triggering   of   the   alarm   when  
a door is opened, you have to press
the

  remote   control   unlocking   button  
again.Do

  not   make   any   modifications  
to

  the   alarm   system   as   this   could  
cause

  faults.
access
REadY To Go
3

22
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
SLIDING SIDE DOORS
From the outside
Pull the handle towards you then
towards the rear and open the side
door guiding the rearward sliding to
beyond the point of resistance to hold
it  open.
A
 

mechanical   system   prevents   opening  
of the left-hand side door when the fuel
filler

  flap   is   open.
From the inside
Unlock the side door using this handle and open it, guiding the rearward
sliding  to   the   point   of   resistance.   Pass  
this

  point   to   hold   the   door   open.
Close the side door using the handle
to start the sliding and pass the point
of
  resistance.  
Then,
  use   the   shaped  
recess at the top of the door pilla

r to
guide
  the   door   until   it   locks.
d

o not use the grab handle to slide the
door.
Good practice
Take care not to block the guide space on   the   floor   to   allow   the   door   to   slide  
correctly

.
If
  your   vehicle   is   parked   on   a   slope,  
guide

  the   sliding   of   the   side   door.   In  
fact,

  the   door   could   open   or   close   more  
rapidly due to the slope of the ground
and

  could   cause   injury.
For safety and operation reasons, do
not drive with the sliding side doors
open.
access

23
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
Operation in the event
of a battery failure
Front and side passenger doors
In the event of a battery or of the
central  locking   fault,   use   the   lock   to  
lock

  the   doors   mechanically.
-

T
o open the door and get out of the
vehicle,
  pull   the   interior   control.
-
 
T
o   lock   the   door,   insert   the   key   in  
the

  lock,   located   on   the   edge   of   the  
door

, then turn it one eighth of a
turn.
Driver's door
-
 
Insert
  the   key   in   the   lock,   then   turn  
it

  to   the   right   to   lock   or   to   the   left   to  
unlock.
TAILGATE
From inside
(emergency control)
In  the   event   of   a   central   unlocking  
operating

  fault,   this   permits   unlocking  
of

  the   tailgate   from   the   inside.
Insert
  a   small   screwdriver   in   the  
opening, between the tailgate and the
floor

.  
T
o   unlock   the   lock,   move   the  
catch

  to   the   left   then   push   the   tailgate.
Opening
From outside
Locking/unlocking  is   by   means   of   the  
remote

  control.
To open, press the control below the
trim
  then   raise   the   tailgate.
a pull strap is available to close the
tailgate

  in   the   high   position.
Guide the closing of the tailgate to the
balance point of its travel then apply
a
  final   press   on   the   tailgate   to   close   it  
fully

.
access
REadY To Go
3

24
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
HINGED REAR DOORS
From outside
To open, pull the handle towards you.Pull the lever to open the right-hand
door
.
To close, start with the right-hand door
then   close   the   left-hand   door.
With   the   roof   rear   flap,   the   rear   bumper  
has been reinforced to serve as a
footrest

  when   entering   the   vehicle.
The hinged rear doors are
asymmetrical   (2/3   -   1/3),   with   the  
smaller

  door   on   the   right.
They   are   fitted   with   a   central   lock.
Tailgate screen
The opening rear screen allows you to
access the rear of the vehicle directly,
without
  having   to   open   the   tailgate.
Opening
After
  unlocking   the   vehicle   using   the  
remote

  control   or   the   key,   press   the  
control and raise the rear screen to
open

  it.
Closing
Close the rear screen by pressing
the centre of the glass until it is fully
closed.
The tailgate and tailgate screen
cannot both be open at the
same

  time,   to   prevent   damage   to  
the screen.
access

25
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
In practice
It is possible to drive with the right-
hand  door   open   to   make   it   easier   to  
carry

  long   loads.  
The
  left-hand   door   is  
kept

  closed   by   the   distinctive   "yellow"  
lock,

  positioned   at   the   base   of   the   door.  
This

  closed   door   must   not   be   used   as  
a

  load   retainer.
d

riving with the right-hand door open
is
  a   special   dispensation.   Comply   with  
the usual safety indications to warn
other

  drivers.
From inside
When present on the vehicle, pulling
this handle towards you opens the left-
hand  door.
Opening to approximately 180°
A check   strap   system   permits   extension  of
  the   opening   from   approximately   90°  
to

  approximately   180°.
Pull the yellow control when the door is
open.
The
  check   strap   will   engage   again  
automatically

  on   closing.
When parked with the rear  doors   open   to   90°,  
the

  doors   mask   the   rear  
lamps.

 
T
o   signal   your  
position to other road
users

  driving   in   the   same  
direction

  who   may   not  
have seen your vehicle,
use a warning triangle
or other device required
by the legislation in your
country

.
access
REadY To Go
3

26
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
REAR ROOF FLAP
Support bar
a support bar is provided for
transporting long loads, after opening
the
  rear   roof   flap.
Fold
  back   the   support   bar   by   lifting   the  
lever

.
Guide
  it   to   the   door   pillar.
Support the long loads to be
transported,
  lift   them   and   reposition   the  
support

  bar   with   one   hand.
Ensure that it is secured correctly by
pressing the handle downwards past
the point of resistance and secure the
loads
  firmly. The
  rear   bumper   has   been  
reinforced to serve as a footrest
when

  entering   the   vehicle.
The   rear   doors   only   lock   when   the  
support

  bar   is   installed.
When
  the   rear   roof   flap   is   open,   take  
care when driving where height is
restricted.
n

ever rest loads directly on the rear
doors.
Comply
  with   the   usual   indications,   to  
warn

  other   drivers.
Reserve
  the   use   of   the   rear   roof   flap  
for

  short   journeys.
The side supports can be used as
hooking
  points.
-  
lower
  the   black   paddle   to   secure  
the

  rear   roof   flap.
Securing   the   rear   roof   flap   places   it   on  
the seal correctly and ensures sealing
without

  noise.
This
 
rear
 
roof
 
flap
 
is
 
only
 
compatible
 
with

 
side-hinged
 
rear
 
doors.
To
 
open
 
the
 
rear
 
roof
 
flap:
-
 
raise

 
the
 
black
 
paddle
 
of
 
the
 
toggle,
-

relieve the toggle by pressing the
rear

 
roof
 
flap
 
(downwards)
 
then
 release
 
the
 
hook,
-
 lift
 
the
 
rear
 
roof
 
flap,
-

pass the point of resistance to
secure

 
the
 
rear
 
roof
 
flap
 
using
 
the
 
support

 
stays.
Never
 
drive
 
without
 
the
 
stays
 
in
 
place.
To
 
close
 
the
 
rear
 
roof
 
flap:
-
 
check

 
that
 
the
 
support
 
bar
 
is
 
secured correctly

,
-
 
lower

 
the
 
rear
 
roof
 
flap,
-
 
while

 
pressing
 
the
 
rear
 
roof
 
flap
 
(downwards),

 
take
 
hold
 
of
 
the
 
two


loops of the spring then place
the
 
hook
 
in
 
its
 
housing,
n
ever attach any load to the rear roof
flap.n ever drive without the support bar in
place.
access

27
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
CENTRAL LOCKING
An initial press permits central
  locking   of   the   vehicle,  
when all of the doors are
closed.
Door open warning lamp
The

  control   switch   LED:
-  
flashes
  when   the   doors   are   locked  
with the vehicle stationary and the
engine of

f,
-
 
comes
  on   when   the   doors   are  
locked

  and   from   the   time   the  
ignition

  is   switched   on.
Anti-intrusion security
If this warning lamp comes on,  check   that   all   of   your  
vehicle's doors are closed
correctly

.
Locking while driving
When the vehicle moves off, as soon as
  you   reach   approximately   6   mph (10 km/h),

  the   system   locks   the   doors.
 The

  characteristic   central   locking   noise
 is

  heard.  
The
  LED   in   the   switch   on   the
 dashboard

  central   switch   panel   comes   on.
During the journey, opening a door results  in   complete   unlocking   of   the  
vehicle.
Activating / deactivating the
function
With the ignition on, press
and hold this switch to
activate or deactivate the
function.
Driving

 
with
 
the
 
doors
 
locked
 
may
 
make

 
access
 
to
 
the
 
interior
 
more
 
difficult

 
in
 
an
 
emergency.
A
 

second
 
press
 
permits
 
central
 
unlocking

 
of
 
the
 
vehicle.
The control is inactive when the vehicle
has
 
been
 
locked
 
using
 
the
 
remote
 
control

 
or
 
the
 
key
 
from
 
the
 
outside.
The
 
doors
 
can
 
still
 
be
 
opened
 
from
 
the
 
inside.
access
REadY To Go
3

28
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
Instruments and controls
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
Dials
1. Distance  recorder   in   kilometres   /  miles.
2.
 
Display
  screen.
3.
 
Fuel
  gauge,   coolant   temperature.
4.
 
Rev
  counter.
5.
 
T
rip   distance   recorder   /   service  
indicator

  reset.
6.
 
Instrument
  panel   lighting   dimmer.Level 1
INSTRUMENT PANELDisplay screens
Screens
The format of the information presented in the screen depends on
the
  vehicle's   equipment   level.
Level 2
with the touch screen tablet