display CITROEN C CROSSER 2009 User Guide

I
I N S T R U M E N T S a n d C O N T R O L S
28
Message is on Cause Solution - action Observations
Saturation of the particle
emission fi lter Fixed
Start of saturation of the particle
emission fi lter. As soon as traffi c
conditions permit,
regenerate the fi lter
by driving at a speed
of at least 35 mph
(60 km/h) until the
message is cleared. If the message is still
displayed, contact a
CITROËN dealer.
Diesel
additive level Fixed Low diesel additive level. Have the level
topped up by a
CITROËN dealer
without delay.
Water in the diesel fi lter
(according to country) Fixed The presence of water in the
diesel fi lter is indicated.
Risk of damage to the injection
system on Diesel engines. Contact a CITROËN
dealer without delay.

I
I N S T R U M E N T S a n d C O N T R O L S
29
Prevention messages
Information messages (ignition at "ON")

Message is on Status of the system
2WD two wheel drive system Flashing When the "2WD" (2 wheel drive) mode is selected using the
transmission mode selector.
4WD four wheel drive system Flashing When the "4WD" (4 wheel drive) mode is selected using the
transmission mode selector.
This mode is the default mode.
4WD LOCK four
wheel drive system Flashing When the "LOCK" (4 wheel drive) mode is selected using the
transmission mode selector.
Exterior
temperature Fixed This indicates the exterior temperature.
When the vehicle is stationary or if the speed is below 12 mp
h
(20 km/h) the temperature displayed may not correspond to the
exterior temperature.

Display is on Cause Solution - action Observations
Service
indicator Fixed Informs the driver of
the time remaining
before the vehicle's
scheduled service. Consult a CITROËN
dealer.
This is displayed for a few
seconds when the ignition is
switched on.
Break
advised Fixed Informs the driver that
he should stop to take
a break. You are advised to
take a break. This is displayed when the
driving time that you set
previously is reached.
An audible signal is heard
3 times and is then heard every
5 minutes until the vehicle
stops.

I
30
The total distance is dis-
played in zone 1 of the
display and the trip dis-
tance in zone 2 (refer to
the "Distance recorders"
section).
Distance recorder (A and B)
INFORMATION ON THE
INSTRUMENT PANEL DISPLAY
Data displays
With the ignition on, press the
INFO but-
ton, located on the fascia to the right of
the instrument panel, to display the vari-
ous information displays in succession:
- the distance recorder A,
- the distance recorder B,
- the service indicator,
- the coolant temperature,
- the range,
- the trip computer,
- the setting menu.
This displays the distance
and the number of months
remaining before the next
service to be carried out in
accordance with the manu-
facturer’s servicing schedule
(refer to the "Service indica-
tor" section).
Service indicator
When the engine is run-
ning, this indicates the
temperature of the cool-
ant (refer to the "Coolant
temperature indicator"
section).
Coolant temperature When the engine is run-
ning, this indicates the
number of miles (kilo-
metres) which can still
be travelled with the fuel
remaining in the tank in
relation to the average
consumption over the
last few miles (kilometres) travelled (re-
fer to the "Range" section).
Range
This indicates the aver-
age consumption, the
average speed and the
current consumption (re-
fer to the "Trip computer"
section).
Trip computer

When the vehicle is
stationary , this allows
the user to change the
following parameters
(refer to the "Function
parameters" section):
- the display language,
- the temperature dis- play unit,
- the fuel consumption unit,
- the option to reinitialise the aver- age consumption and the average
speed,
- the break (rest) reminder display in- terval.
Setting menu

I
!
!
I N S T R U M E N T S a n d C O N T R O L S
31
The total distance is dis-
played in zone 1 of the
display and the trip dis-
tance in zone 2 .
DISTANCE RECORDERS (A/B)
System for measuring the total dis-
tance travelled by the vehicle during its
service life and the distance travelled in
a day or other period until it is reset to
zero by the driver.
Zero reset
With the ignition on, press the INFO
button for more than 2 seconds until
zeros appear.
When the engine is run-
ning, this indicates the tem-
perature of the coolant.
COOLANT TEMPERATURE
If the bar is close to the critical position
located on the right, the temperature is
too high.
The symbol fl ashes when your engine
is overheating.

It is imperative that you stop your
vehicle safely.

Wait a few minutes before switching
off the engine.
Wait for the engine to cool before
topping up the level. The cooling
system is pressurised.
When the engine is
running , this indicates
the distance which can
still be travelled with
the fuel remaining in the
tank in relation to the av-
erage consumption over
the last few miles/kilo-
metres travelled.
RANGE
When the range is less than 30 miles
(50 km) , dashes are displayed.
Fill the fuel tank as soon as possible.
The display of the range is updated.
To avoid any risk of scalding, unscrew
the cap by two turns to allow the pres-
sure to drop.
When the pressure has dropped, re-
move the cap and top up the level, if
necessary.
Consult a CITROËN dealer. This fi gure may increase following a
change in the style of driving or the
relief, resulting in a reduction in the
current consumption.
If you only add a few litres, the value
displayed will be incorrect. There-
fore, you must fi ll the tank whenever
possible.
When you disconnect the battery,
the previous consumption data is
lost and the value displayed will
be different from that displayed before
the battery was disconnected. The dis-
tance displayed must be considered
an approximate indication.

I
I N S T R U M E N T S a n d C O N T R O L S
32
SERVICE INDICATOR Resetting the service indicator to zero
Your CITROËN dealer carries out this
operation after each service.
If you have carried out your vehicle's
service yourself, the zero reset proce-
dure is the following:

 switch off the ignition.

 press the INFO button several times
in succession until the service indi-
cator is displayed.

 press and hold the INFO button for
a few seconds until the spanner
fl ashes .

 press the INFO button while the
spanner is fl ashing to change the
display "---" to "CLEAR" then the
time remaining before the next serv-
ice is due is displayed.
Service overdue
Operation
When the ignition is switched on, you
must press the INFO button several
times in succession until the service
indicator is displayed. The distance re-
corder display line indicates the number
of miles (kilometres) remaining and the
time elapsed line indicates the number
of months remaining before the next
service is due.
After a certain distance and a certain
time, the displaying of "---" is reinitialised
and the display indicates the time re-
maining before the next service is due.
System which informs the driver when
the next service is due in accordance
with the manufacturer's servicing
schedule.
The point at which the next service is
due is calculated from the last service
indicator zero reset.
It is determined by two parameters:
- the distance travelled (in miles (km),
- the time elapsed since the last service (in months).
The distance remaining to be travelled
may be weighted by the time factor, de-
pending on the user's driving habits.
Example: the display indicates that
7 300 miles (kilometres) remain before
the next service is due.
The symbol "--" remains displayed
until the fi rst service of a new vehicle
has been carried out.

Example: the display indicates that the
service is overdue. This service must
be carried out by a CITROËN dealer.
Each time the ignition is switched on,
the display
"SCHEDULED SERVICE"
is displayed for a few seconds to indi-
cate that the service must be carried
out without delay.

I
!
!
I N S T R U M E N T S a n d C O N T R O L S
31
The total distance is dis-
played in zone 1 of the
display and the trip dis-
tance in zone 2 .
DISTANCE RECORDERS (A/B)
System for measuring the total dis-
tance travelled by the vehicle during its
service life and the distance travelled in
a day or other period until it is reset to
zero by the driver.
Zero reset
With the ignition on, press the INFO
button for more than 2 seconds until
zeros appear.
When the engine is run-
ning, this indicates the tem-
perature of the coolant.
COOLANT TEMPERATURE
If the bar is close to the critical position
located on the right, the temperature is
too high.
The symbol fl ashes when your engine
is overheating.

It is imperative that you stop your
vehicle safely.

Wait a few minutes before switching
off the engine.
Wait for the engine to cool before
topping up the level. The cooling
system is pressurised.
When the engine is
running , this indicates
the distance which can
still be travelled with
the fuel remaining in the
tank in relation to the av-
erage consumption over
the last few miles/kilo-
metres travelled.
RANGE
When the range is less than 30 miles
(50 km) , dashes are displayed.
Fill the fuel tank as soon as possible.
The display of the range is updated.
To avoid any risk of scalding, unscrew
the cap by two turns to allow the pres-
sure to drop.
When the pressure has dropped, re-
move the cap and top up the level, if
necessary.
Consult a CITROËN dealer. This fi gure may increase following a
change in the style of driving or the
relief, resulting in a reduction in the
current consumption.
If you only add a few litres, the value
displayed will be incorrect. There-
fore, you must fi ll the tank whenever
possible.
When you disconnect the battery,
the previous consumption data is
lost and the value displayed will
be different from that displayed before
the battery was disconnected. The dis-
tance displayed must be considered
an approximate indication.

I
I N S T R U M E N T S a n d C O N T R O L S
32
SERVICE INDICATOR Resetting the service indicator to zero
Your CITROËN dealer carries out this
operation after each service.
If you have carried out your vehicle's
service yourself, the zero reset proce-
dure is the following:

 switch off the ignition.

 press the INFO button several times
in succession until the service indi-
cator is displayed.

 press and hold the INFO button for
a few seconds until the spanner
fl ashes .

 press the INFO button while the
spanner is fl ashing to change the
display "---" to "CLEAR" then the
time remaining before the next serv-
ice is due is displayed.
Service overdue
Operation
When the ignition is switched on, you
must press the INFO button several
times in succession until the service
indicator is displayed. The distance re-
corder display line indicates the number
of miles (kilometres) remaining and the
time elapsed line indicates the number
of months remaining before the next
service is due.
After a certain distance and a certain
time, the displaying of "---" is reinitialised
and the display indicates the time re-
maining before the next service is due.
System which informs the driver when
the next service is due in accordance
with the manufacturer's servicing
schedule.
The point at which the next service is
due is calculated from the last service
indicator zero reset.
It is determined by two parameters:
- the distance travelled (in miles (km),
- the time elapsed since the last service (in months).
The distance remaining to be travelled
may be weighted by the time factor, de-
pending on the user's driving habits.
Example: the display indicates that
7 300 miles (kilometres) remain before
the next service is due.
The symbol "--" remains displayed
until the fi rst service of a new vehicle
has been carried out.

Example: the display indicates that the
service is overdue. This service must
be carried out by a CITROËN dealer.
Each time the ignition is switched on,
the display
"SCHEDULED SERVICE"
is displayed for a few seconds to indi-
cate that the service must be carried
out without delay.

I
I N S T R U M E N T S a n d C O N T R O L S
33
TRIP COMPUTER Average consumption (l/100 km or km/l or mpg)
This is the average quan-
tity of fuel consumed
since the last zero reset.
This fi gure may increase following a
change in the style of driving or the
relief resulting in a reduction in the
current consumption.
Average speed(km/h or mph)
This is the average
speed calculated since
the last zero reset.
Resetting the information to zero
When the ignition is switched on, the
zero reset switches automatically from
manual mode to automatic mode.
If dashes "---" are displayed for long
periods in place of the digits while
driving, contact a CITROËN dealer.
Current consumption (l/100 km or km/l or mpg)
This is the average
quantity of fuel con-
sumed during the last
few seconds of driving.
Data displays
With the ignition on, press the INFO
button on the fascia, to the right of the
instrument panel, several times in succes-
sion to display the different information:
- the average consumption,
- the average speed,
- the current consumption. When the required information is dis-
played, press the
INFO button for more
than two seconds to reset all of the in-
formation to zero.
Automatic
If the ignition key remains in the OFF
position for more than 4 hours, the in-
formation is reset to zero automatically.

I
!
I N S T R U M E N T S a n d C O N T R O L S
34

When the vehicle is
stationary , it allows the
user to change the fol-
lowing parameters:
-
the choice of the reini-
tialisation of the average
consumption and average
speed,
- the fuel consumption unit,
- the temperature display unit,
- the display language,
- activation/deactivation of the INFO
button sound,
- the break (rest) reminder display in- terval,
-
restore the manufacturer’s parameters.
FUNCTION PARAMETERS
System which provides access to cer-
tain function parameters.
In order to change the settings, it
is essential that you stop the ve-
hicle and switch on the ignition.
Apply the handbrake and place the
gear lever in neutral.
When the vehicle is moving , the
functions setting display is not dis-
played when you press the INFO
button.
The various menus may differ for the
type 1 instrument panel and the type 2
instrument panel.

With the ignition on , press the INFO
button on the fascia, to the right of the
instrument panel, several times in suc-
cession until the "SETTING MENU"
screen is displayed.
Operation

 press and hold the INFO button for
a few seconds to display the menus
screen.
Press and hold the INFO button for
a few seconds to return to the previ-
ous screen.
When the menus screen is dis-
played, if no operation is carried out
within 15 seconds, the function pa-
rameters screen is displayed.

 on the menus screen, press the

INFO button to select a function
from the list:

MENU
2/3:
- a/b (choice of displaying a different
language on the instrument panel
display and the navigation display),
- activation/deactivation of the INFO
button sound ,
- ALERT (changing of the "BREAK
REMINDER" display interval),
- choice of the direction indicators sound,
- activation/deactivation of the cur-
rent fuel consumption ,

MENU
1/3 :
- 1 - 2 (choice of the reinitialisation of
the average consumption and aver-
age speed),
- UNIT (choice of the fuel consump-
tion units),
- choice of the temperature display
unit ,
- LANGUAGE (choice of the display
language),
MENU 3/3:
- REINITIALISE (restore the manu-
facturer’s parameters).

I
I N S T R U M E N T S a n d C O N T R O L S
35
Choice of the fuel consumption units
You can choose between different units
for displaying the fuel consumption. On the menus screen:

 press the INFO button to select

"UNIT" .

 press and hold the INFO button for
a few seconds to display the "UNIT"
screen.

 press the INFO button to scroll the
units (km/L, L/100km, mpg(US),
mpg(UK) and PREVIOUS) in suc-
cession.

 press and hold the INFO button for
a few seconds to confi rm your se-
lection.
In this case, the distance, speed and
quantity of fuel units will also be changed
in accordance with your choice of fuel
consumption unit.
If the battery is disconnected, the
parameter memory is cleared and
the default unit (km/L) is restored
automatically.
Choice of the temperature display unit
You can choose between different units
for displaying the temperature.
On the menus screen:


press the INFO button to select
the temperature unit parameters
symbol (thermometer).

 press and hold the INFO button for
a few seconds to scroll the units (°C
and °F) in succession.
The mode selected is confi rmed.
If the battery is disconnected, the pa-
rameter memory is cleared and the
default unit (°C) is restored automati-
cally.
Choice of the reinitialisation of the average consumption and average speed
You can choose between two average
consumption and average speed reini-
tialisation modes:
- automatic reinitialisation ( choice 1) ,
- manual reinitialisation (choice 2) .
On the menus screen:

 press the INFO button to select:

 press and hold the INFO button for
a few seconds to switch in succes-
sion from reinitialisation mode 1

(automatic) to reinitialisation mode

2 (manual) .
The mode selected is confi rmed.