Citroen C CROSSER 2012 1.G Owner's Guide

I
29
Message
is on
Cause
Solution - action
Observations

Saturation of
the particle
emission fi lter
Fixed Start of saturation of the particle
emission fi lter. As soon as traffi c
conditions permit,
regenerate the fi lter
by driving at a speed
of at least 35 mph
(60 km/h) until the
message is cleared. If the message is still
displayed, contact a
CITROËN dealer or
a qualifi ed workshop.

Diesel
additive level
Fixed Low Diesel additive level. Have the level
topped up by a
CITROËN dealer or
a qualifi ed workshop
without delay.

Water in the
Diesel fi lter
(according to
country)
Fixed The presence of water in the
Diesel fi lter is indicated.
Risk of damage to the injection
system on Diesel engines. Contact a CITROËN
dealer or a qualifi ed
workshop without
delay.

I
MONITORING
30

Prevention messages




Information messa
ges (ignition at "ON")



Message



is on



Status of the system



2WD two wheel
drive system
Flashing When the "2WD" (2 wheel drive) mode is selected using the
transmission mode selector.

4WD four wheel
drive system
Flashing When the "4WD" (4 wheel drive) mode is selected using the
transmission mode selector.
This mode is the default mode.

4WD LOCK four
wheel drive system
Flashing When the "LOCK" (4 wheel drive) mode is selected using the
transmission mode selector.

Ambient
temperature
Fixed This indicates the ambient temperature.
When the vehicle is stationary or if the speed is below 12 mph (20 km/h)
the temperature displayed may not be the true temperature.


Display



is on



Cause



Solution - action



Observations



Service
indicator
Fixed Informs the driver of
the time remaining
before the vehicle's
scheduled service. Contact a CITROËN
dealer or a qualifi ed
workshop. This is displayed for a few
seconds when the ignition is
switched on.

Break
advised
Fixed Informs the driver that
they should stop to
take a break. You are advised to
take a break. This is displayed when the
driving time that you set
previously is reached.
An audible signal is heard
3 times and is then heard every
5 minutes until the vehicle stops.

I
31 The total distance is
displayed in zone 1
of the screen and the
trip distance in zone 2

(refer to the "Distance
recorders" section).
Distance recorder (A and B)
INFORMATION ON THE
IN
STRUMENT PANEL SCREEN
Information displa
y
With the ignition on, press the INFO
button, located on the fascia to the
left of the instrument panel, to display
the various types of information in
succession:


- distance recorder A,

- distance recorder B,

- service indicator,

- coolant temperature,

- range,

- trip computer,

- setting menu. This displays the distance
and the number of
months remaining before
the next service, in line
with the manufacturer's
servicing schedule (refer
to the "Service indicator"
section).
Service indicator
When the engine is
running, this indicates
the temperature of the
coolant (refer to the
"Coolant temperature
indicator" section).
Coolant temperature When the engine is
running, this indicates
the number of miles
(kilometres) which can
still be travelled with the
fuel remaining in the tank,
based on the average
fuel consumption over
the last few miles (kilometres) travelled
(refer to the "Range" section).
Range
This indicates the average
fuel consumption, the
average speed and the
current fuel consumption
(refer to the "Trip
computer" section).
Trip computer

When the vehicle is
stationary
, this allows
the user to change the
following settings (refer
to the "Setting menu"
section):


- the display language,

- the temperature dis-
play units,

- the fuel consumption units,

-
the option to reinitialise the average fuel
consumption and the average speed,

- the break (rest) reminder display interval.




Setting menu

I
!
!
MONITORING
32 The total distance is
displayed in zone 1
of
the screen and the trip
distance in zone 2
.
DISTANCE RECORDERS (A/B)

System for measuring the total distance
travelled by the vehicle during its
service life and the distance travelled in
a day or other period until it is reset to
zero by the driver.
Zero reset
With the ignition on, press the INFO
button for more than 2 seconds until
zeros appear. When the engine is
running, this indicates
the temperature of the
coolant.
COOLANT TEMPERATURE
If the bar is close to the critical
position
located on the right, the temperature is
too high.
The symbol fl ashes when your engine
is overheating.

You must stop your vehicle as soon
as it is safe to do so.


Wait a few minutes before switching
off the engine.

Wait for the engine to cool before
topping up the level. The cooling
system is pressurised.
When the engine is
running
, this indicates
the distance which can
still be travelled with the
fuel remaining in the tank
based on the average
fuel consumption over
the last few miles/
kilometres travelled.
RANGE
When the range is less than 30 miles
(50 km)
, dashes are displayed.
Refuel as soon as possible. The display
of the range is updated.
To avoid any risk of scalding, unscrew
the cap by two turns to allow the
pressure to drop.
When the pressure has dropped,
remove the cap and top up the level, if
necessary.
Contact a CITROËN dealer or a
qualifi ed workshop. This fi gure may increase following a
change in the style of driving or the
relief, resulting in a reduction in the
current fuel consumption.
If you only add a few litres, the
value displayed will be incorrect.
Therefore, you must fi ll the tank
whenever possible.
When you disconnect the
battery, the previous fuel
consumption data is lost and the
value displayed will be different from
that displayed before the battery was
disconnected. The distance displayed
must be considered an approximate
indication.

I
MONITORING
33
SERVICE INDICATOR Resetting the service indicator to zero
Your CITROËN dealer or a qualifi ed
workshop carries out this operation
after each service.
If you have carried out your vehicle's
service yourself, the zero reset
procedure is the following:


)
switch off the ignition.

)
press the INFO
button several times
in succession until the service indi-
cator is displayed.

)
press and hold the INFO
button for
a few seconds until the spanner
fl ashes
.

)
press the INFO
button while the
spanner is fl ashing to change the dis-
play "---"
to "CLEAR"
then the time
remaining before the next service is
due is displayed.


Service overdue
O
peration
When the ignition is switched on, you
must press the INFO
button several
times in succession until the service
indicator is displayed. The distance
recorder display line indicates the
number of miles (kilometres) remaining
and the time elapsed line indicates the
number of months remaining before the
next service is due.
After a certain distance and a certain
time, the display of "---"
is reinitialised
and the display indicates the time
remaining before the next service is
due. System which informs the driver when
the next service is due in accordance
with the manufacturer's servicing
schedule.
The point at which the next service is
due is calculated from the last service
indicator zero reset.
It is determined by two parameters:


- the distance travelled (in miles (km)),

- the time elapsed since the last ser-
vice (in months).
The distance remaining to be travelled
may be weighted by the time factor,
depending on the user's driving habits.
Example:
the display indicates that
7 300 miles (kilometres) remain before
the next service is due.
The symbol "--"
remains displayed
until the fi rst service of a new vehicle
has been carried out.

Example:
the display indicates that the
service is overdue. This service must
be carried out by a CITROËN dealer or
a qualifi ed workshop. Each time the ignition is switched on,
the display "PERIODIC INSPECTION"

is displayed for a few seconds to
indicate that the service must be carried
out without delay.

I
MONITORING
34
TRIP COMPUTER Average fuel consumption (l/100 km or km/l or mpg)
This is the average fuel
consumption since the
last zero reset.
This fi gure may change following
a change in the style of driving or
the relief resulting in an increase
or decrease in the current fuel
consumption.


Average speed (km/h
or mph)
This is the average
speed calculated since
the last zero reset.
Resetting the information to zero

When the ignition is switched on, the
zero reset switches automatically from
manual mode to automatic mode.
If dashes "---" are displayed for long
periods in place of the digits while
driving, contact a CITROËN dealer or
a qualifi ed workshop.


Current fuel consumption(l/100 km or km/l or mpg)
This is the average fuel
consumption during the
last few seconds of driving.
Information display

With the ignition on, press the INFO

button on the dashboard, to the left
of the instrument panel, several times
in succession to display the different
information:


- average fuel consumption,

- average speed,

- current fuel consumption. When the required information is
displayed, press the INFO
button for
more than two seconds to reset all of
the information to zero.

Automatic
If the ignition key remains in the
OFF position for more than 4 hours,
the information is reset to zero
automatically.

I
!
MONITORING
35
When the vehicle is
stationary
, it allows
the user to change the
following settings:


- the choice of the reini-
tialisation of the aver-
age fuel consumption
and average speed,

- the fuel consumption units,

- the temperature display unit,

- the display language,

- activation/deactivation of the INFO
button sound,

- the break (rest) reminder display in-
terval,

- restore the factory settings.
SETTING MENU

System which provides access to the
settings for certain functions.
To change the settings, you
must stop the vehicle and switch
on the ignition.
Apply the parking brake and place
the gear lever in neutral.
When the vehicle is moving
, the
function settings are not displayed
when you press the INFO
button.
The various menus may change
between the type 1 instrument panel
and the type 2 instrument panel.

With the ignition on
, press the INFO

button on the dashboard, to the left of
the instrument panel, several times in
succession until the "SETTING MENU"
screen is displayed.

Operation



)
press and hold the INFO
button for
a few seconds to display the menu
screen.
Press and hold the INFO
button
for a few seconds to return to the
previous screen.
When the menu screen is displayed,
if no operation is carried out within
15 seconds, the Setting Menu
screen is displayed.
)
on the menu screen, press the INFO
button to select a function from the
list:


MENU

2/3:



- a/b
(option of displaying a different
language on the instrument panel
screen and the navigation screen),

- activation/deactivation of the INFO


button sound
,

- ALERT
(changing of the "BREAK
REMINDER" display interval),

- selection of the sound
of the direc-
tion indicators,

- activation/deactivation of the cur-
rent fuel consumption
,

MENU

1/3

:



- 1 - 2
(choice of the type of reinitiali-
sation of average fuel consumption
and average speed),

- UNIT
(choice of the fuel consump-
tion units),

- choice of the temperature display
unit
,

- LANGUAGE
(option of the display
language),
MENU 3/3:



- REINITIALISE
(restore factory set-
tings).

I
MONITORING
36
Choice of the fuel consumption units
You can choose between different units
for displaying fuel consumption. On the menus screen:


)
press the INFO
button to select
"UNIT"
.

)
press and hold the INFO
button for
a few seconds to display the "UNIT"

screen.

)
press the INFO
button to scroll the
units (km/L, L/100km, mpg (US),
mpg (UK) and PREVIOUS) in suc-
cession.

)
press and hold the INFO
button for a
few seconds to confi rm your selection. In this case, the distance, speed and
quantity of fuel units will also be changed
in accordance with your choice of fuel
consumption unit. If the battery is disconnected, the
settings memory is cleared and
the default unit (km/L) is restored
automatically.


Choice of the temperature
display unit
You can choose between different units
for displaying the temperature.
On the menu screen:


)
press the INFO
button to select
the temperature unit setting
symbol (thermometer).

)
press and hold the INFO
button for
a few seconds to scroll the units
(°C and °F) in succession.
The mode selected is confi rmed.
If the battery is disconnected, the
settings memory is cleared and
the default unit (°C) is restored
automatically.


Choice of the reinitialisation of
the average consumption and average speed
You can choose between two average
fuel consumption and average speed
reinitialisation modes:


- automatic reinitialisation (choice 1)
,

- manual reinitialisation (choice 2)
.
On the menu screen:


)
press the INFO
button to select:

)

press and hold the INFO
button for a
few seconds to switch in succession
from reinitialisation mode 1



(automatic)

to reinitialisation mode 2 (manual)
.

The mode selected is confi rmed.

I
MONITORING
37
Choice of the display language
You can choose between different
languages for the display.
On the menu screen:


)
press the INFO
button to select
"LANGUAGE"
.

)
press and hold the INFO
button
for a few seconds to display the
"LANGUAGE"
screen.

)
press the INFO
button to scroll
the languages (Japonais, English,
Deutsch, Français, Espanol, Italiano,
"---" and PREVIOUS) in succession.

)
press and hold the INFO
button for
a few seconds to confi rm your se-
lection.
If you select the "---" setting, no
message will be displayed in
message display situations. If the battery is disconnected, the
settings memory is cleared and
the default language (ENGLISH) is
restored automatically.


Activation/deactivation of the"INFO" button sound

You can activate or deactivate the INFO
button sound.
On the menu screen:


)
press the INFO
button to se-
lect the INFO
button sound
activation/deactivation sym-
bol (located on menu 2/3)
.

)
press and hold the INFO
button for
a few seconds to scroll the choices
(ON, OFF) in succession.
The mode selected is confi rmed.
If the battery is disconnected, the
settings memory is cleared and
the default choice (ON) is restored
automatically.


Changing the display interval
of the "BREAK REMINDER"
message
You can change the display interval of
the "BREAK REMINDER"
message.
On the menu screen:


)
press the INFO
button to select
"ALERT" (located on menu 2/3)
.

)
press and hold the INFO
button
for a few seconds to display the
"ALERT"
screen.

)
press the INFO
button to select
the display interval of the "BREAK
REMINDER"
message.

)
press and hold the INFO
button for
a few seconds to confi rm.
If the battery is disconnected, the
settings memory is cleared and
the default value (OFF) is restored
automatically.

I
MONITORING
38
Selection of the sound of thedirection indicators
You can select the sound of the direction
indicators, with the type 2 instrument
panel only.
On the menu screen:


)
press the INFO
button to select
sound 1 or 2 (located on menu 2/3)
.


Functions

Factory

setting



Reinitialisation
of average fuel
consumption and
average speed

1
(automatic)

Fuel consumption
units

L/100 km



Temperature
display unit

°C



Display language

ENGLISH



INFO button
sound

ON
(activated)

Display of
the "BREAK
REMINDER"
message


OFF
(deactivated)


Activation/deactivation of the current fuel consumption

You can activate or deactivate the
current fuel consumption, with the type 2
instrument panel only.
On the menu screen:


)
press the INFO
button to select the
current fuel consumption activation/
deactivation symbol (located on
menu 2/3)
.
)
press and hold the INFO
button for
a few seconds to scroll through the
choices in succession (ON, OFF).



Restoring factory settings(REINITIALISE)

You can restore all of the factory settings
for all functions.
On the menu screen:


)
press the INFO
button to select
"REINITIALISE"

(located on menu
2/2 or 3/3 depending on the in-
strument panel)
. The factory settings are:

)
press and hold the INFO
button for
at least 5 seconds
.
An audible signal is heard and all of
the factory settings are restored for all
functions.