set clock Citroen C CROSSER DAG 2008 1.G Owner's Manual

I
37
MONOCHROME DISPLAY
This provides the following information:
- the time,
- the audio equipment displays (refer to the “Audio and Telematics” sec-
tion). Setting the time
The digital clock can be set in
automatic
mode or in
manual mode . Selecting the Setting
Select the
automatic mode or the

manual mode as follows:

 Press button A “PWR” to switch on
the audio system.

 Access the setting mode by press-
ing button B “TUNE” for approxi-
mately 2 seconds.

 Press button B “TUNE” several
times to scroll through the various
menus and select the CT menu
(clock time).
The order of the menus is the
following: AF / CT / REG / TP-S / PTY
display language / SCV / PHONE /
Functions setting mode OFF.
Automatic mode
This mode permits automatic setting of
the local time using the signal from the
RDS stations.
The symbol
“CT” appears on the
display.
Manual mode
This mode permits manual setting of
the time using the audio equipment
buttons.
It can also be used when the “Automatic
mode” displays an inaccurate time, when
the local RDS stations are broadcasting
from a different time zone.

I N S T R U M E N T S a n d C O N T R O L S
I
38
Set the time using the buttons as
indicated below:

 with the ignition on or in the ACC
(Accessories) position, press and
hold the CLOCK button until the
time display fl ashes.
 Press the appropriate button to set
the time:

Button H: setting of the hour
The hours digits scroll when you press
this button.

Button M: setting of the minutes
The minutes digits scroll when you
press this button.

Button :00: resetting of the minutes to
zero.
- from 1 to 29 min
: rounded down to
the previous hour,
- from 30 to 59 min: rounded up to
the next hour.
Manual mode
Automatic mode
In this mode, setting is automatic using
the signal from the RDS radio stations.
 After setting the time, press the

DISP button; the time display stops
fl ashing.
The digital clock does not display
seconds.
When the “minutes” display is set or
reset to zero, the clock starts at the
zero second of the minute selected.
The time setting is lost if the battery
is disconnected.

 Turn button B “TUNE” to the left or
to the right to select “CT ON” (auto-
matic mode) or “CT OFF” (manual
mode).

 After selecting the mode, you can
exit the “Functions setting mode”
menu by pressing button B “TUNE”
for approximately 2 seconds.
If no action is carried out within
10 seconds, the system will exit
the “functions setting mode” menu
automatically.

I N S T R U M E N T S a n d C O N T R O L S
I
40
Setting the time
The digital clock is set automatically .
This mode enables the system to set
the local time automatically using the
signal from the RDS stations.

 On the control panel, press button

A (SET) to access the “Settings”
menu.

 On the touch screen, press button

B to access the “System” menu.
The system settings screen is
displayed.
“Information” menu
On the control panel, press button
D
(INFO) to access the “Info” screen and
consult:
- “Support info” to display the
software and data versions,
- “Vehicle position” to display the
GPS location of the vehicle,
- “Calendar” to make a note of events,
birthdays, etc.,
- “Journey” to display the average
speed, the consumption, the
distances and the duration of driving,
- “Environment” to display the
altitude, the atmospheric pressure,
the exterior temperature (the ice
symbol is displayed if there is a risk
of ice),
- “Air conditioning” to display
the information relating to the air
conditioning,
- “Mobile telephone” to enter a
number, delete a character, make or
receive a call. “Map” menu
On the control panel, press button
E
(NAVI) to access the “Routes Menu”
screen and select:
- “Detour” to make a detour through
a specifi ed region,
- “Route” to change the route,
- “Display a route” to display a route
in different ways,
- “Delete a route” to delete a route,
- “Local POI” to search for the POIs
in the surrounding area.