buttons CITROEN C-ELYSÉE 2016 Owners Manual

26
Setting the date and time
Instrument panel
Use the left-hand button on the instrument panel to carry out the operations in the
following
 or

der:
F
 
p
ress   the   button   for   more   than  
t

wo   seconds:   the   minutes   flash,
F
 
p
ress   the   button   to   increase   the   minutes,
F
 
p
ress   the   button   for   more   than  
t

wo seconds:   the   hours   flash,
F

p
ress the button to increase the hours,
F
 
p
ress   the   button   for   more   than  
t

wo   seconds:   24H   or   12H   is   displayed,
F
 
p
ress   the   button   to   select   24H   or   12H,
F
 
p
ress  
t
he  
b
utton  
f
or  
m
ore  
t
han  
t
wo  
s
econds  
t

o   complete   the   adjustments.
After
  approximately   30   seconds   without   any  
a

ction,   the   screen   returns   to   the   normal   display.
Audio system / Bluetooth
Use the audio system buttons to carry out the operations   in   the   following   order:
F

p
ress the "MENU" button,
F
 
u
sing   the   arrows,   select   the  
"

Personalisation - Configuration"
 
menu  
t

hen   confirm   by   pressing   the   control   knob,F
 
u
sing   the   arrows,   select   the   "Screen
configuration"
 
menu   then   confirm,
F  
u
sing   the   arrows,   select   the   "Set date and
time"
 
menu   then   confirm,
F  
s
elect   the   setting   then   confirm,
F
 
m
odify   the   setting   then   confirm   again   to  
r

egister   the   modification,
F
 
a
djust   the   settings   one   by   one,   confirming  
e

ach   time,
F

s
elect the "OK" tab in the screen then
confirm
  to   exit   the   "Set date and time"
menu.
Monitoring

29
C-elysee_en_Chap01_controle-de-marche_ed01-2016
C-elysee_en_Chap01_controle-de-marche_ed01-2016
Monochrome screen C (Audio system / Bluetooth)
This displays the following information:
-  t ime,
-
 d

ate,
-
 
a
mbient   temperature   (this   flashes   if   there   is  
a

  risk   of   ice),
-
 
s
tatus   of   doors   and   boot,
-
 
p
arking   sensors,
-
 
a
udio   sources   (radio,   CD,   USB   port,  
j

ack socket...),
-
 
t
rip   computer   (refer   to   the   "Instruments   and  
c

ontrols"
 s
ection).
Warning
  or   information   messages   may   appear  
t

emporarily.   These   can   be   cleared   by   pressing  
t

he " BACK "
  button. From
  your   Audio   system   /   Bluetooth   control  p
anel,   you   can   press:
F
the "MENU"
 

button   to   gain   access   to   the  
m

ain menu,
F
the "MODE"
 

button   to   select   the   display  
o

f   information   in   "Full   screen"   or   "New  
w

indow"   mode,
F

t
he "7" or " 8"
  buttons   to   navigate   in   a   list,
F
 
p
ress   the   central   button   to   confirm,


or
F

t
he "BACK "
  button   to   abandon   the  
o

peration   in   progress   or   go   back   up   one  
l

evel   in   the   menu.
Displays in the screenControls
F Press the "MENU" button   to   gain   access  t
o the main menu :
-
 
"
Multimedia",
-
 "

Telephone",
-
 
"
Trip   computer",
-
 
"
Bluetooth   connection",
-
 "

Personalisation-configuration",
F

P
ress the " 7" or " 8" buttons to select the
menu
  required,   then   confirm   by   pressing  
t

he   centre   button.
Main menu
1
Monitoring

36
C-elysee_en_Chap02_ouvertures_ed01-2016
Lost keys
Go to a CITROËN dealer with the vehicle's registration document, your personal identification   documents   and   if   possible   the   key   code   label.
The
  CITROËN   dealer   will   be   able   to   look   up   the   key   code   and   the   transponder   code  
r

equired   to   order   a   new   key.
Remote control
The high frequency remote control is a sensitive system; do not operate it while it is in your pocket   as   there   is   a   possibility   that   it   may   unlock   the   vehicle,   without   you   being   aware   of   it.
Do
  not   repeatedly   press   the   buttons   of   your   remote   control   out   of   range   and   out   of   sight   of  
y

our   vehicle.   You   run   the   risk   of   stopping   it   from   working   and   the   remote   control   would   have  
t

o   be   reinitialised.
No
  remote   control   can   operate   when   the   key   is   in   the   ignition   switch,   even   when   the   ignition  
i

s   switched   off,   except   for   reinitialisation.
Locking the vehicle
Driving with the doors locked may make access to the passenger compartment by the emergency   services   more   difficult   in   an   emergency.
As
  a   safety   precaution,   never   leave   children   alone   in   the   vehicle,   except   for   a   very   short  
p

eriod.
In
  all   cases,   it   is   essential   to   remove   the   key   from   the   ignition   switch   when   leaving   the   vehicle.
Anti-theft protection
Do not make any modifications to the electronic engine immobiliser system; this could cause m alfunctions.
When purchasing a second-hand vehicle
Have the pairing of all of the keys in your possession checked by a CITROËN dealer, to ensure   that   only   your   keys   can   be   used   to   open   and   start   the   vehicle.Do
  not   throw   the   remote   control  
b

atteries   away,   they   contain   metals  
w

hich   are   harmful   to   the   environment.
Take   them   to   an   approved   collection  
po

int.
Ac

53
C-elysee_en_Chap03_confort_ed01-2016
Electronic air conditioning (with display screen)
These systems only operate with the engine running.
1. Air intake / Air recirculation
The recirculation of interior air isolates the
passenger  compartment   from   exterior   odours  
a

nd   smoke.
2. Temperature level adjustment
F Press the " 5"   (red   for   hot)  a
nd "6"
  (blue   for   cold)   buttons,  
t

o   adjust   the   temperature   to   your  
r

equirements.
The
  temperature   bars   come   on  
o

r   go   off   progressively   in   the   air  
c

onditioning
 s
creen.
Return
 
to
 
exterior
 
air
 
intake
 
as
 
soon
 
as
 
possible
 
t

o
 
prevent
 
deterioration
 
of
 
the
 
the
 
air
 
quality
 
a

nd
 
the
 
formation
 
of
 
mist.
F

P

ress the button to recirculate the interior
air.
 
The
 
indicator
 
lamp
 
comes
 
on
 
to
 
confirm
 
t

his. F
 
P

ress
 
the
 
button
 
again
 
to
 
p

ermit
 
the
 
intake
 
of
 
exterior
 
air.
 
T

he indicator
 
lamp
 
goes
 
off
 
to
 
c

onfirm
 
this.
3. Front demist - defrost
See the corresponding section.
3
Comfort

86
C-elysee_en_Chap05_conduite_ed01-2016
F Turn  thumb   wheel   1 to the
"LIMIT"  position:
  the   speed   limiter  
m

ode   is   selected   but   is   not   switched   on  
(

PAUS E).
You
  do   not   have   to   switch   the   speed   limiter  
o

n   in   order   to   set   the   speed.
Programming Leaving limiter mode
F Turn  thumb   wheel   1 to the "0"  position:  t
he   speed   limiter   mode   is   deselected.   The  
d

isplay   returns   to   the   distance   recorder.
On
  a   steep   descent   or   in   the   event   of  
s

harp   acceleration,   the   speed   limiter  
w

ill not be able to prevent the vehicle
from
  exceeding   the   programmed   speed.
To
  avoid   any   risk   of   jamming   of   the  
ped

als:
-
 
e
nsure   that   the   mat   is   secured  
c

o r r e c t l y,
-
 
d
o   not   fit   one   mat   on   top   of   another.
In
  the   event   of   a   speed   limiter   fault,   the   speed  
i

s   cleared   and   the   dashes   then   flash.
Have
  it   checked   by   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.
Operating fault
F Set  the   speed   value   by   pressing   button   2 or 3   (e.g.:   55   mph  (
90 km/h)).
You
  can   then   change   the   programmed   speed   using   buttons   2   and   3:
-
 
b
y   +   or   -   1   mph   (km/h)   =   short   press,
-
 
b
y   +   or   -   5   mph   (km/h)   =   long   press,
-
 
i
n   steps   of   +   or   -   5   mph   (km/h)   =   maintained   press.
Exceeding the programmed speed
Pressing the accelerator pedal to exceed the programmed speed will not   have   any   effect   unless   you   press   the   pedal   firmly past the point of
resistance .
The
 

speed
 
limiter
 
is
 
deactivated
 
temporarily
 
and
 
the
 
programmed
 
speed,
 w

hich   is   still   displayed,   flashes,   accompanied   by   an   audible   signal.
Returning
  to   the   programmed   speed,   by   means   of   intentional   or  
u

nintentional   deceleration   of   the   vehicle,   automatically   cancels   the  
f

lashing   of   the   programmed   speed   and   the   audible   signal   stops.
F
 
S
witch   the   speed   limiter   back   on   by   pressing   button   4  
ag
ain.
F  
S
witch   the   speed   limiter   on   by   pressing   button   4
.
F  
S
witch   the   speed   limiter   off   by   pressing   button   4
:   the   display  
c

onfirms   that   it   has   been   switched   off   (PAUSE).
Driving

88
C-elysee_en_Chap05_conduite_ed01-2016
F Turn  thumb   wheel   1 to the
"CRUISE"  position:
  the   cruise   control  
m

ode   is   selected   but   is   not   switched   on  
(

PAUS E).
Programming
You can then change the programmed speed using buttons 2 and 3:
-  b y   +   or   -   1   mph   (km/h)   =   short   press,
-
 
b
y   +   or   -   5   mph   (km/h)   =   long   press,
-
 
i
n   steps   of   +   or   -   5   mph   (km/h)   =   maintained   press. When
  the   cruise   control   is   switched   on,  
b

e   careful   if   you   maintain   the   pressure  
o

n   one   of   the   programmed   speed  
c

hanging   buttons:   this   may   result   in   a  
v

ery   rapid   change   in   the   speed   of   your  
v

ehicle.
Do not use the cruise control on
slippery
  roads   or   in   heavy   traffic.
On
  a   steep   descent,   the   cruise   control  
w

ill not be able to prevent the vehicle
from
  exceeding   the   programmed   speed.
To
  avoid   any   risk   of   jamming   of   the  
ped

als:
-
 
e
nsure   that   the   mat   is   secured  
c

o r r e c t l y,
-
 
n
ever   fit   one   mat   on   top   of   another.
In
  the   event   of   a   cruise   control   malfunction,  
t

he   speed   is   cleared   resulting   in   flashing   of   the  d
ashes.   Have   it   checked   by   a   CITROËN   dealer  o
r   a   qualified   workshop.
Operating fault
Leaving cruise control mode
F Turn   thumb   wheel   1 to the "0"  position:   the   cruise   control   mode   is  d
eselected.   The   display   returns   to   the   distance   recorder.
Exceeding the programmed speed
Intentional or unintentional exceeding of the programmed speed results   in   flashing   of   this   speed   in   the   screen.
Return
  to   the   programmed   speed,   by   means   of   intentional   or  
u

nintentional   deceleration   of   the   vehicle,   automatically   cancels   the  
f

lashing   of   the   speed.F
 
S
et   the   programmed   speed   by  
a

ccelerating   to   the   required   speed,  
t

hen press button 2 or 3   (e.g.:   70   mph  
(

110   km/h)).
F  
S
witch   off   the   cruise   control   by   pressing   button   4
:   the   screen  
c

onfirms   that   it   has   been   switched   off   (PAUSE).
F  
S
witch   the   cruise   control   back   on   by   pressing   button   4  
ag
ain.
Driving

02
197
C-elysee_en_Chap12a_RD5(RD45)_ed01-2016
STEERING MOUNTED CONTROLS
Radio: automatic search for a higher frequency.
CD   /   MP3   /   USB:   selection   of   the   next   track.
CD
  /   USB:   continuous   press:   fast   forwards   play.
Move
  in   the   list. Change
  audio   source.
Confirm
  a   selection.
Call/end
  call   on   the   telephone.
Press
  for   more   than   2   seconds:  
telephone

  main   menu.
Radio:
  automatic   search   for   a   lower  
frequency

.
CD
  /   MP3   /   USB:   selection   of   the  
previous

  track.
CD
  /   USB:   continuous   press:   fast  
reverse.
Move

  in   the   list.
Radio:
 
select
 
the
 
previous/next
 
pre-set
 
station.
USB:

 
select
 
genre
 
/
 
artist
 
/
 
folder
 
from
 
the
 
classification

 
list.
Select
 
the
 
previous/next
 
item
 
in
 
a
 
menu. Volume
  increase.
Volume
  decrease.Mute:
  press   the   volume  
increase

  and   decrease  
buttons

  simultaneously.
The
  sound   is   restored  
by

  pressing   one   of   the  
two volume

  buttons.

04
202
C-elysee_en_Chap12a_RD5(RD45)_ed01-2016
AUDIO
Audio CD
Insert 12 cm diameter circular compact discs only.
Some   anti-pirating   systems,   on   original   discs   or   CDs   copied   using   a  
personal

  recorder,   may   cause   faults   which   are   no   reflection   on   the  
quality

  of   the   original   player.
Without
  pressing   the   EJECT button, insert a CD in the player, play
begins
  automatically.
To
  play   a   disc   which   has   already   been  
inserted,

  press   the   SRC/TEL button
several
  times   in   succession   and  
select

"CD".
Press one of the buttons to select a
track
  on   the   CD.
Playing a CD
Press LIST  to   display   the   list   of   tracks  
on

  the   CD.
Press
  and   hold   one   of   the   buttons   for  
fast

  forward   or   backward.

04
204
C-elysee_en_Chap12a_RD5(RD45)_ed01-2016
CD, USB
AUDIO
Playing a compilationInsert   an   MP3   compilation   in   the   CD   player  
or

  connect   a   memory   stick   to   the   USB   port,  
directly

  or   via   an   extension   lead.
The
  system   creates   playlists   (temporary   memory)   the   creation   time  
for

  which   can   take   from   a   few   seconds   to   several   minutes.
The
  playlists   are   updated   every   time   the   ignition   is   switched   off   or   a  
USB

  memory   stick   is   connected.
Play
  starts   automatically   after   a   period   which   depends   on   the  
capacity

  of   the   USB   memory   stick.
Use
  only   USB   memory   sticks   formatted   FAT32   (File  
Allocation
 
T
able).
At
  a   first   connection,   the   order   suggested   is   by   folder.  
When

  connecting   again,   the   order   previously   chosen   is  
retained.T

o   play   a   disc   or   memory   stick   which  
has

  already   been   inserted,   press  
SRC
/
TEL
  several   times   in   succession   and  
select "

CD" or "USB". Turn
  the   control   knob   to   select   the   next  
or

  previous   track.
Press one of the buttons to select the
next
  or   previous   folder   in   the   order  
chosen.
Press

  and   hold   one   of   the   buttons   for  
fast

  forwards   or   backwards.
Press LIST
 

to   display   the   menu   of  
folders

  in   the   compilation.

05


213
C-elysee_en_Chap12a_RD5(RD45)_ed01-2016
USING THE TELEPHONE
To display the "TELEPHONE "   menu:
-  
Make
  along   press   on  
SRC/TEL
.
-
 
Or
,   press   the   control   knob   to  
display

  the   contextual   menu.   Select  
"

Call"   and   confirm.
-
 
Or
,   press   MENU, select
"Telephone"
  and   confirm.   Select  
"

Call"   and   confirm.
Select "Dial"
  to   enter   a   number   and  
confirm. T

o   display   the   "TELEPHONE"
  menu:
-
 
Make
  a   long   press   on  
SRC/TEL
.
-
 
Or
,   press   the   dial   to   display   the  
contextual

  menu.   Select   "Call"
  and  
confirm.
-

 
Or
,   press   MENU, select
"Telephone"
  and   confirm.   Select  
"

Call"   and   confirm.
Press
  the   control   knob   to   confirm   to  
start

  the   call. Select "Calls list"
  and   confirm.
Making a call - Dialling
Select numbers one at a time using the 7   and   8   buttons   and   confirm.
Making a call - Recently called numbers*
Select the number and confirm to start the  call.
The
 
calls
 
list   includes   calls   sent   and   received   in   the   vehicle   using   the  
connected

 
telephone.
*
 
Depending
 
on
 
the
  compatibility   of   the   telephone.
Correction
 
allows
 
numbers
 
to
 
be
 
deleted
 
one
 
at
 
a
 
time.
It
 
is
 
possible   to   make   a   call   directly   from   the   telephone;   park   the  
vehicle

 
first
  as   a   safety   measure.