ECO mode CITROEN C-ELYSÉE 2017 User Guide

82
C-elysee_en_Chap05_conduite_ed01-2016
Stop & Start
Operation
Going into engine STOP mode
The "ECO" warning   lamp   comes  o
n   in   the   instrument   panel   and   the  
e

ngine   goes   into   standby:
-
 
w

ith a 5-speed electronic gearbox , with
the vehicle stationary, when you press
the
 
brake   pedal   or   put   the   gear   selector   in  
p

osition N .
A
 
time
 
counter   calculates   the   sum   of   the  
p

eriods
 
in
  STOP   mode   during   a   journey.   It   rests  
i

tself
 
to
 
zero   every   time   the   ignition   is   switched  
o

n
 
with
 
the   key.
The
 
Stop
 
&
 
Start system
 
puts
 
the
 
engine
 
t

emporarily
 
into
 
standby
 
-
 
STOP
 
mode
 
-
 
during
 
s

tops
 
in
 
the
 
traffic
 
(red
 
lights,
 
traffic
 
jams,
 
or
 o
ther...).
 
The
 
engine
 
restarts
 
automatically
 
-
 S
TART
 
mode
 
-
 
as
 
soon
 
as
 
you
 
want
 
to
 
move
 
o

ff.
 
The
 
restart
 
takes
 
place
 
instantly,
 
quickly
 
a

nd
 
silently.
Per fect
 
for
 
urban
 
use,
 
the
 
Stop
 
&
 
Start
 
system
 
r

educes
 
fuel
 
consumption
 
and
 
exhaust
 
e

missions
 
as
 
well
 
as
 
the
 
noise
 
level
 
when
 
s

tationary. Never
  refuel   with   the   engine   in  
S

TOP mode;   you   must   switch   off   the  
i

gnition   with   the   key.
For
  your   comfort,   during   parking  
m

anoeuvres,   STOP   mode   is   not  
a

vailable   for   a   few   seconds   after  
c

oming   out   of   reverse   gear.
STOP
  mode   does   not   affect   the  
f

unctionality of the vehicle, such as for
example,
  braking,   power   steering...
Driving

83
C-elysee_en_Chap05_conduite_ed01-2016
Going into engine START mode Special cases: START invoked automatically
The "ECO" warning   lamp   goes  o
ff   and   the   engine   starts   with   an  
e

lectronic gearbox :
-
 
g

ear
 
selector   in   position   A or M, when you
release
  the   brake   pedal,
-
 
o

r
 
gear   selector   in   position   N   and   the   brake  
p

edal
  released,   when   you   move   the   gear  
s

elector to position A or M ,
-
 
o

r
 
when   you   engage   reverse   gear.For
  reasons   of   safety   and   for   your   comfort,  S
TART   mode   is   invoked   automatically   when:
-
 
y
ou   open   the   driver's   door,
-
 
y
ou   unfasten   the   driver's   seat   belt,
-
 
t
he   speed   of   the   vehicle   exceeds   2   mph  
(

3 km/h)   with   an   electronic   gearbox,
-
 
s
ome   special   conditions   (battery   charge,  
e

ngine   temperature,   braking   assistance,  
a

mbient   temperature...)   where   the   engine   is  
n

eeded   for   control   of   a   system.
The "ECO"
 

warning   lamp   flashes   for  
a

  few   seconds,   then   goes   off.
This operation is per fectly normal.
Special cases: STOP mode not
available
STOP mode is not invoked when:
-  t he   driver's   door   is   open,
-
 
t
he   driver's   seat   belt   is   not   fastened,
-
 
t
he   engine   is   needed   to   maintain   a  
c

omfortable   temperature   in   the   passenger  
c

ompartment,
-
 
d
emisting   is   active,
-
 
s
ome   special   conditions   (battery   charge,  
e

ngine   temperature,   braking   assistance,  
a

mbient   temperature...)   where   the   engine   is  
n

eeded   to   assure   control   of   a   system.
The "ECO"
 

warning   lamp   flashes   for  
a

  few   seconds   then   goes   off.
This operation is per fectly normal.
5
Driving

84
C-elysee_en_Chap05_conduite_ed01-2016
In the event of a fault with the system, the indicator   lamp   in   the   "ECO OFF" button
flashes
  for   a   few   moments,   then   comes   on  
c

ontinuously.
Have
  it   checked   by   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.
In
  the   event   of   a   fault   in   STOP   mode,   the  
v

ehicle   may   stall.   All   of   the   warning   lamps  
i

n   the   instrument   panel   come   on.   It   is   then  
n

ecessary   to   switch   off   the   ignition   and   start  
t

he   engine   again   using   the   key.
Operating fault
The Stop & Start system requires 
a   12   V   battery   with   a   special  
s

pecification
 a
nd
 t
echnology.
All
  work   on   this   type   of   battery   must   be  
c

arried   out   only   by   a   CITROËN   dealer  
o

r   a   qualified   workshop.
For
  more   information   on   the   12   V  
b

attery,   refer   to   the   corresponding  
s

ection.
Press
 
this
 
button
 
to
 
deactivate
 
the
 
system.
Deactivation
 
is
 
confirmed
 
by
 
illumination
 
of
 
the
 i
ndicator
 
lamp
 
in
 
the
 
button
 
and
 
the
 
display
 
of
 
a

 
message.
Pressing
 
this
 
button
 
again
 
reactivates
 
the
 
s

ystem.
The
 
indicator
 
lamp
 
in
 
the
 
button
 
goes
 
off,
 
a

ccompanied
 
by
 
the
 
display
 
of
 
a
 
message.
Deactivation / Manual
reactivation
In certain cases, such as the need to maintain a   comfortable   temperature   in   the   passenger  
c

ompartment,   it   may   be   useful   to   deactivate   the  
S

top   &   Start   system.
The
  system   can   be   deactivated   at   any   time,  
o

nce   the   ignition   is   on.
If
  the   engine   is   in   STOP   mode,   it   then   restarts.
The
  Stop   &   Start   system   is   reactivated  
a

utomatically   every   time   the   ignition   is  
switched
  on.
Opening the bonnet
Before
  doing   anything   under   the  
b

onnet,   deactivate   the   Stop   &   Start  
s

ystem   to   avoid   the   risk   of   injury  
r

elated   to   an   automatic   change   to  
S

TART mode.
Driving on flooded roads
Before
  driving   through   a   flooded   road,  
i

t   is   strongly   recommended   that   you  
d

eactivate   the   Stop   &   Start   system.
For
  more   advice   on   driving,   particularly  
o

n   flooded   roads,   refer   to   the  
c

orresponding
 s
ection.
Driving

86
C-elysee_en_Chap05_conduite_ed01-2016
F Turn  thumb   wheel   1 to the
"LIMIT"  position:
  the   speed   limiter  
m

ode   is   selected   but   is   not   switched   on  
(

PAUS E).
You
  do   not   have   to   switch   the   speed   limiter  
o

n   in   order   to   set   the   speed.
Programming Leaving limiter mode
F Turn  thumb   wheel   1 to the "0"  position:  t
he   speed   limiter   mode   is   deselected.   The  
d

isplay   returns   to   the   distance   recorder.
On
  a   steep   descent   or   in   the   event   of  
s

harp   acceleration,   the   speed   limiter  
w

ill not be able to prevent the vehicle
from
  exceeding   the   programmed   speed.
To
  avoid   any   risk   of   jamming   of   the  
ped

als:
-
 
e
nsure   that   the   mat   is   secured  
c

o r r e c t l y,
-
 
d
o   not   fit   one   mat   on   top   of   another.
In
  the   event   of   a   speed   limiter   fault,   the   speed  
i

s   cleared   and   the   dashes   then   flash.
Have
  it   checked   by   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.
Operating fault
F Set  the   speed   value   by   pressing   button   2 or 3   (e.g.:   55   mph  (
90 km/h)).
You
  can   then   change   the   programmed   speed   using   buttons   2   and   3:
-
 
b
y   +   or   -   1   mph   (km/h)   =   short   press,
-
 
b
y   +   or   -   5   mph   (km/h)   =   long   press,
-
 
i
n   steps   of   +   or   -   5   mph   (km/h)   =   maintained   press.
Exceeding the programmed speed
Pressing the accelerator pedal to exceed the programmed speed will not   have   any   effect   unless   you   press   the   pedal   firmly past the point of
resistance .
The
 

speed
 
limiter
 
is
 
deactivated
 
temporarily
 
and
 
the
 
programmed
 
speed,
 w

hich   is   still   displayed,   flashes,   accompanied   by   an   audible   signal.
Returning
  to   the   programmed   speed,   by   means   of   intentional   or  
u

nintentional   deceleration   of   the   vehicle,   automatically   cancels   the  
f

lashing   of   the   programmed   speed   and   the   audible   signal   stops.
F
 
S
witch   the   speed   limiter   back   on   by   pressing   button   4  
ag
ain.
F  
S
witch   the   speed   limiter   on   by   pressing   button   4
.
F  
S
witch   the   speed   limiter   off   by   pressing   button   4
:   the   display  
c

onfirms   that   it   has   been   switched   off   (PAUSE).
Driving

87
C-elysee_en_Chap05_conduite_ed01-2016
Cruise control
System which automatically maintains the speed   of   the   vehicle   at   the   value   programmed  
b

y   the   driver,   without   any   action   on   the  
a

ccelerator
 ped
al.
The cruise control is switched on
 
m
anually:
 it r

equires   a   minimum   vehicle   speed   of   25   mph  
(

40   km/h),   as   well   as   the   engagement   of:
-
 
f
ourth   gear   on   a   manual   gearbox,
-
 
s
econd   gear   on   a   or   automatic   or   electronic  
g

earbox,   in   sequential   mode,
-
 
p
osition   A   on   an   electronic   gearbox   or  
p

osition D   on   an   automatic   gearbox.
The cruise control is switched off
 
m
anually
 o

r   by   pressing   the   brake   or   clutch   pedal   or   on  
t

riggering   of   the   trajectory   control   systems   for  
s

afety   reasons.
It
  is   possible   to   exceed   the   programmed   speed  
t

emporarily   by   pressing   the   accelerator   pedal.
To
  return   to   the   programmed   speed,   simply  
r

elease   the   accelerator   pedal.
Switching
  off   the   ignition   cancels   any  
p

rogrammed   speed   value. The
  controls   of   this   system   are   grouped  
t

ogether   on   stalk   A.
1.
 C

ruise   control   mode   selection   thumb  
w

heel.
2.
 V

alue   decrease   button.
3.
 V

alue   increase   button.
4.
 C

ruise   control   off/resume   button.Steering mounted controls
The cruise control cannot, in any
circumstances,  replace   the   need   to r

espect   speed   limits,   nor   can   it   replace   the
 n

eed   for   vigilance   on   the   part   of   the   driver.The
  programmed   information   is   grouped  
t

ogether   in   the   instrument   panel   screen.
5.
  C
ruise   control   off/resume   indication.
6.
  C
ruise   control   mode   selection   indication.
7.
  P
rogrammed   speed   value.
Displays in the instrument
panel
5
Driving

88
C-elysee_en_Chap05_conduite_ed01-2016
F Turn  thumb   wheel   1 to the
"CRUISE"  position:
  the   cruise   control  
m

ode   is   selected   but   is   not   switched   on  
(

PAUS E).
Programming
You can then change the programmed speed using buttons 2 and 3:
-  b y   +   or   -   1   mph   (km/h)   =   short   press,
-
 
b
y   +   or   -   5   mph   (km/h)   =   long   press,
-
 
i
n   steps   of   +   or   -   5   mph   (km/h)   =   maintained   press. When
  the   cruise   control   is   switched   on,  
b

e   careful   if   you   maintain   the   pressure  
o

n   one   of   the   programmed   speed  
c

hanging   buttons:   this   may   result   in   a  
v

ery   rapid   change   in   the   speed   of   your  
v

ehicle.
Do not use the cruise control on
slippery
  roads   or   in   heavy   traffic.
On
  a   steep   descent,   the   cruise   control  
w

ill not be able to prevent the vehicle
from
  exceeding   the   programmed   speed.
To
  avoid   any   risk   of   jamming   of   the  
ped

als:
-
 
e
nsure   that   the   mat   is   secured  
c

o r r e c t l y,
-
 
n
ever   fit   one   mat   on   top   of   another.
In
  the   event   of   a   cruise   control   malfunction,  
t

he   speed   is   cleared   resulting   in   flashing   of   the  d
ashes.   Have   it   checked   by   a   CITROËN   dealer  o
r   a   qualified   workshop.
Operating fault
Leaving cruise control mode
F Turn   thumb   wheel   1 to the "0"  position:   the   cruise   control   mode   is  d
eselected.   The   display   returns   to   the   distance   recorder.
Exceeding the programmed speed
Intentional or unintentional exceeding of the programmed speed results   in   flashing   of   this   speed   in   the   screen.
Return
  to   the   programmed   speed,   by   means   of   intentional   or  
u

nintentional   deceleration   of   the   vehicle,   automatically   cancels   the  
f

lashing   of   the   speed.F
 
S
et   the   programmed   speed   by  
a

ccelerating   to   the   required   speed,  
t

hen press button 2 or 3   (e.g.:   70   mph  
(

110   km/h)).
F  
S
witch   off   the   cruise   control   by   pressing   button   4
:   the   screen  
c

onfirms   that   it   has   been   switched   off   (PAUSE).
F  
S
witch   the   cruise   control   back   on   by   pressing   button   4  
ag
ain.
Driving

99
C-elysee_en_Chap06_visibilite_ed01-2016
Courtesy lamps
In this position, the courtesy lamp c
omes   on   gradually:
-
 
w

hen
  the   vehicle   is   unlocked,
-
 
w

hen
  the   key   is   removed   from   the   ignition,
-
 
w

hen
  a   door   is   opened,
-
 
w

hen
  the   remote   control   locking   button   is  
a

ctivated,   in   order   to   locate   your   vehicle.
It
 
switches   off   gradually:
-
 
w

hen
  the   vehicle   is   locked,
-
 
w

hen
  the   ignition   is   switched   on,
-
 
3

0
 
seconds   after   the   last   door   is   closed.
Permanently
  off.
Permanent
 l

ighting. F
 W ith   the   ignition   on,   press   the  
c

orresponding
 s
witch.
A.

C

our tesy lamps
B.

M

ap reading lamps With
  the   "permanent   lighting"   mode,   the  
d

uration   of   lighting   varies,   depending   on  
t

he
 c
ircumstances:
-
 
w
ith   the   ignition   off,   approximately  
t

en
 m
inutes,
-
 
i
n   energy   economy   mode,  
a

pproximately   thirty seconds,
-
 
w
ith   the   engine   running,   unlimited.
Front map reading lampsFront and rear courtesy lamps
6
V

168
C-elysee_en_Chap09_info-pratiques_ed01-2016
System which manages the duration of use of certain functions to retain a sufficient level of
charge
  in   the   battery.
After
  the   engine   has   stopped,   you   can  
s

till   use   functions   such   as   the   audio   and  
t

elematics   system,   windscreen   wipers,   dipped  
b

eam   headlamps,   courtesy   lamps,   etc.   for  
a

  maximum   combined   duration   of   about  
t

hirty
 m
inutes.
Electrical energy economy mode
Switching to economy mode
Once this time has elapsed, a message appears   in   the   screen   indicating   that   the  
v

ehicle   has   switched   to   economy   mode   and   the  
a

ctive   functions   are   put   on   standby.
If
  a   telephone   call   is   being   made   at   this   time,  
it
  will   be   maintained   for   around   10   minutes   with  
t

he   Bluetooth   hands-free   system   of   your   audio  
s

ystem.
Exiting economy mode
These functions are reactivated automatically n ext   time   the   vehicle   is   driven.
F
 
T
o   restore   these   functions   immediately,  
s

tart   the   engine   and   let   it   run   for   at   least  
f

ive
 m
inutes.
A
  flat   battery   prevents   the   engine   from  
s

tarting   (refer   to   the   corresponding  
s

ection).
Load reduction mode
System which manages the use of certain functions   according   to   the   level   of   charge  
r

emaining   in   the   battery.
When
  the   vehicle   is   being   driven,   the   load  
r

eduction   function   temporarily   deactivates  
c

ertain   functions,   such   as   the   air   conditioning,  
t

he   heated   rear   screen...
The
  deactivated   functions   are   reactivated  
a

utomatically   as   soon   as   conditions   permit.
Practical information

189
C-elysee_en_Chap11_caracteristiques-techniques_ed01-2016
EnginePureTech 72PureTech
82 PureTech
82 S&S VTi 115
Gearbox Manual
(5-speed) ETG
 e

lectronic
(5-speed) Manual
(5-speed) ETG
 e

lectronic
(5-speed) Manual
(5-speed) Automatic
 (

4-speed)E AT 6
 au

tomatic
 (

6-speed)
Model code: DD... HMY0 HMY0/PHMZ6HMZ6/PS NFP0
NFP6NFP9
NFPT
Unladen
  weight 980980 980 1
  0901
  115
Kerb
  weight* 1
  0551
  055 1   0551
  1651
  190
Gross
  vehicle   weight   (GV W) 1
  459 1   467 1   470149 0 1
  524 1   559 1   585
Gross
  train   weight   (GTW)
on
  a   12%   gradient 1
  909 1   917 1   920 1   990 2   274 2   309 2   335
Braked
  trailer   (within   the   GTW   limit)  
o

n   a   10%   or   12%   gradient 450
450500 750
Braked
  trailer**   (with   load   transfer   within   the  
G

TW   limit) 720
720 720 1
  010
Unbraked
 t

railer 450450 450 580
Recommended
  nose   weight 555555 55
*
  The   kerb   weight   is   equal   to   the   unladen   weight   +   driver   (75   kg).
**
  
T
he   weight   of   the   braked   trailer   can   be   increased,   within   the   GTW   limit,   if   the   GV W   of   the   towing   vehicle   is   reduced   by   an   equal   amount;   warning,  
t

owing   using   a   lightly   loaded   towing   vehicle   may   have   an   adverse   effect   on   its   road   holding.
The
  GTW   and   towed   load   values   indicated   are   valid   up   to   a   maximum   altitude   of   1   000   metres;   the   towed   load   mentioned   must   be   reduced   by   10   %   for  
e

ach   additional   1   000   metres   of   altitude.
The
  speed   of   a   towing   vehicle   must   not   exceed   60   mph   (100   km/h)   (comply   with   the   legislation   in   force   in   your   country).
High
  ambient   temperatures   may   result   in   a   reduction   in   the   per formance   of   the   vehicle   to   protect   the   engine;   if   the   ambient   temperature   is   above   37   °C,  
l

imit   the   towed   load.
Petrol weights (in kg)
11
Technical data

191
C-elysee_en_Chap11_caracteristiques-techniques_ed01-2016
The GTW and towed load values indicated are valid up to a maximum altitude of 1 000 metres; the towed load mentioned must be reduced by 10 % for each   additional   1   000   metres   of   altitude.
The
  speed   of   a   towing   vehicle   must   not   exceed   60   mph   (100   km/h)   (comply   with   the   legislation   in   force   in   your   country).
High
  ambient   temperatures   may   result   in   a   reduction   in   the   per formance   of   the   vehicle   to   protect   the   engine;   if   the   ambient   temperature   is   above   37   °C,  
l

imit   the   towed   load.
*
  The   kerb   weight   is   equal   to   the   unladen   weight   +   driver   (75   kg).
**   
T
he   weight   of   the   braked   trailer   can   be   increased,   within   the   GTW   limit,   if   the   GV W   of   the   towing   vehicle   is   reduced   by   an   equal   amount;   warning,  
t

owing   using   a   lightly   loaded   towing   vehicle   may   have   an   adverse   effect   on   its   road   holding.
Engine
HDi 92BlueHDi 100
Gearbox Manual
 (
5-speed)
Manual
 (
5-speed)
Model code: DD... 9HJC9HP0BHY6
Unladen   weight
1   090
1   090
Kerb   weight*
1   165
1   165
Gross   vehicle   weight   (GV W)
1   549
1   548
1   585
Gross   train   weight   (GTW)
on   a   12%   gradient
2   299
2   298
2   335
Braked   trailer   (within   the   GTW   limit)
on   a   10%   or   12%   gradient
750
750
Brakled   trailer**   (with   load   transfer   within  
the   GTW   limit)
1   010
1   010
Unbraked
 t
railer
580580
Recommended   nose   weight
5555
Diesel weights (in kg)
11
Technical data