level Citroen C2 2004 1.G User Guide

Downloaded from www.Manualslib.com manuals search engine ENGINE
177
CHECKING AND SETTING THE VALVE TIMING
Engines: 6FZ RFN 2003 #
Tensioning the timing belt.
Turn the tensioner roller (8)in the direction of the arrow «c», by means of a hexagonal spanner at «d».
Positionner l’index «a»en position «f».
IMPERATVE: The index «a» should go past the slot «g» by an angular value of 10°.
If it does not, replace the tensioner roller or the timing belt and tensioner roller assembly.
Next bring the index «a»to its adjusting position «g», by turning the tensioner roller in the direction of the arrow «e».
WARNING:the index «a»should not pass the slot «g».
Otherwise, repeat the operation to tension the timing belt.
IMPERATIVE: The tensioner roller should not turn during the tightening of its fixing.
If it does, repeat the operation to tension the timing belt.
Tighten the screw (9)of the tensioner roller (8)to 2,1 ± 0,2 m.daN.
IMPERATIVE: The hexagonal tensioner roller drive should be approx. 15° below the level of the cylinder head
gasket «h».
If it is not, replace the tensioner roller or the timing belt and tensioner roller assembly.
B1EP1BEC
B1EP1BFC
XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine ENGINE
227
CHECKING THE OIL PRESSURE
To be read with the Petrol and Diesel correspondence tables
Plaque engine XFX KFV NFU 8HX
Temperature (°C) 90°C
Pressure (Bars) 3 4 1,3 3,5
Rpm 2000 4000 1000 4000
Tools (Kit 4103T)
2279T.Bis X X X X
4103T.B X X X X
7001T X X X1503.JX
C3 C3 Pluriel
Plaque engineHFXKFVKFUNFU8HX8HW8HV 8HY
Temperature (°C) 90°C
Pressure (Bars) 3 4 1,3 3,5
Rpm 2000 4000 1000 4000
Tools (Kit 4103T)
2279T.Bis X X X X X X X X
4103T.B X X X X X X X X
7001T X X X X
1503.JXX XX
NOTE:The oil pressure
should be checked with the
engine hot, after the oil level
has been checked.
C2 C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 228
ENGINECHECKING THE OIL PRESSURE
To be read with the Petrol and Diesel correspondence tables
XSARA
Plaque engine KFW NFU RFN RFS 8HZ WJY RHY RHZ
Temperature (°C) 90°C 80°C 90°C
Pressure (Bars) 3 4 1,5 5,1 2 5,5 1,3 3,5 1,8 4,5 2 4
Rpm 2000 4000 1000 4000 1000 4000 1000 4000 1000 4000 1000 4000
Tools (Kit 4103T)
2279T.BisXXXXXX XX
4103T.B X X X X X X X X
7001T X
4202T X X X
5709T.B2 X
1503JX
4156TX
7017T.X23X
NOTE:
The oil pressure should be checked with the engine hot, after the oil level has been checked.
XSARA

Downloaded from www.Manualslib.com manuals search engine 229
ENGINE
CHECKING THE OIL PRESSURE
To be read with the Petrol and Diesel correspondence tables
XSARA PICASSO
Plaque engine NFV 6FZ RFN 9HZ 9HY RHY
Temperature (°C) 90°C 80°C 90°C
Pressure (Bars) 3 4 3,3 6,3 1,5 5 1,3 3,5 2 4
Rpm 2000 4000 1000 4000 1000 3000 1000 4000 1000 4000
Tools (Kit 4103T)
2279T.Bis X X X X X X
4103T.B X X X X X X
7001T X
4202T X X X
1503JXX
NOTE:
The oil pressure should be checked with the engine hot, after the oil level has been checked.
XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 231
ENGINE
ALL TYPES FILLING AND BLEEDING THE COOLING CIRCUIT
Tools.
[1]
Filling cylinder: 4520T
[2]Adaptor for filling cylinder: 4222T
IMPERATIVE: Respect the safety and cleanliness requirements.
The draining and refilling operations can be carried out using WINN’S or similar coolant fluid replacement
equipment;it is essential to follow the instructions as stated for that equipment.
Filling and bleeding.
Fit the cylinder adaptor [2] 4222T (Picasso,C2,C3)and the filling cylinder [1] 4520T (all types).
Use the coolant to ensure protection between 15°C and 37°C.
Slowly fill the system.
NOTE:Keep the cylinder filled up (visible level).
Close each bleed screw as soon as the coolant flows without air bubbles.
Start the engine :Engine speed
1500 rpm.
Maintain this speed until the first cooling cycle (cooling fans cut in and cut out).
Stop the engine and allow it to cool down.
Remove the filling cylinder
[1] 4520T (all types)and the cylinder adaptor [2] 4222T.
Top up the system to the max. mark, with the engine cold.
Refit the filler cap.
E5AP1GNCB1GP00AC

Downloaded from www.Manualslib.com manuals search engine 275
INJECTION
SPECIAL FEATURES: FORCED REGENERATION OF THE PARTICLE FILTER
Tools.
Diagnostic stations: LEXIA or PROXIA
Imperative: Respect the safety and cleanliness requirements.
Forced regeneration of the particle filter.
IMPERATIVE: Respect the safety and cleanliness requirements specific to HDi engines.
ESSENTIAL: Connect the vehicle to a gas extractor approved for this type of operation.In the absence of the required installations,carry out the forced regeneration of the particle filter outside the workshop, in a concreted
area well away from any inflammable materials. Place the vehicle in the high position.
WARNING:
Check that the fuel level is sufficient (at least 20 litres).
Start the engine and allow it to warm up (60°C minimum).
Connect the diagnostic tool to the vehicle’s central socket.
Trigger the regeneration cycle, with the diagnostic tool.
Automatic running of the regeneration cycle of the particle filter:
Autocheck by the engine ECU. Stabilisation of engine speed at
4000 rpm, operating with post injection.
Change to idling speed (for 30 seconds).
Stabilisation of engine speed at 3000 rpm, checking of the efficiency of the regeneration of the particle filter.
Change to idling speed.
NOTE:Let the engine run at idling speed for the benefit of cooling.
Stop the engine.
IMPERATIVE: Wait for at least an hour before any operation on the exhaust line.
ALL TYPES

Downloaded from www.Manualslib.com manuals search engine 278
INJECTION
SPECIAL FEATURES: PARTICLE FILTER / CHECKING THE ADDITIVE PUMP
Sealing of the additive injector.
Couple tool [1] to the tube (1).
Action the manual pump [1].
WARNING:The additive injector should open at a pressure of 100 ± 20 Bars.
Action the manual pump in vacuum
[1]at 800 m.bars.
WARNING:The downstream pressure should not fall rapidly.
NOTE:Replace the fuel tank if the injector is defective.
Couple the tube
(1).
Operate the actuator test «Filling the tube: additive pump – additive injector», with the aid ofLEXIAor PROXIA.
Check the additive level.
The checking of the additive level is done with reference to the gradations «a»marked on the additive
reservoir.
The top graduation indicates maximum filling
(3 Litres).
The difference between the two gradations equates to 0,25 Litres.
XSARA PICASSO
B1HP1UUC
B1KP019C

Downloaded from www.Manualslib.com manuals search engine 291
CLUTCH
GEARBOX
TRANSMISSION
CLUTCH CONTROLS: FEATURES / CHECKS AND ADJUSTMENTS HYDRAULIQUE
B2BP04XC
Bleeding the hydraulic clutch control
IMPERATIVE: Use only new brake brake fluid that is not emulsified, avoid any
ingress of impurities into the hydraulic circuit.
IMPERATIVE: Do not use automatic bleeding equipment
(risk of the brake fluid
emulsifying in the hydraulic circuit).
Couple a transparent tube (5) on the bleed screw, at «c».
Submerge the end of the tube
(5)in the recipient containing the brake fluid, located
below the level of the clutch slave cylinder.
Use the transparent tube
(5)to act as a siphon, at «b».
WARNING:the end of the tube (5)must be submerged in the brake fluid.
Open the bleed screw, at
«c».
C3 PLURIEL XSARA
C2C3XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 292
CLUTCH
GEARBOX
TRANSMISSION
CLUTCH CONTROLS: FEATURES / CHECKS AND ADJUSTMENTS HYDRAULIQUE
Bleeding the hydraulic clutch control
Action the clutch pedal manually through its full travel:7 times rapidlydown and up.
Allow the clutch pedal to come back up to its high position.
Fill the brake fluid reservoir to the maximum of its capacity.
Open the bleed screw, at
«c».
Action the clutch pedal manually through its entire travel:7 timesrapidly down and up.
The last time, keep the clutch pedal fully down.
Reclose the bleed screw, at
«c».
If necessary, repeat the operation.
Top up the brake fluid to the MAX. level of the brake fluid reservoir.
Work the clutch vigorously
40 times.
Start the engine.
Apply the handbrake.
Engage a gear.
Check that the clutch starts to engage at a dimension
(X)greater than or equal to 45 mm(the dimension (X)is
given as a guide).
Repeat the bleed operations if necessary.
C5FP0FQCB2BP04YC
C2 C3 C3 PLURIEL
XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 295
CLUTCH
GEARBOX
TRANSMISSION
Engine type Trim level
Tyresrolling Circumference
Speedometer ratio Gearbox type
Gearbox ident.plate
Reduction box torque
Engine type Trim level
Tyresrolling Circumference
Speedometer ratio
(1) Export et DAIC
= 20 CP 16 (14X60) (21X18) (2) EXPORT et DAIC= 20 CP 55 20 CP 72 (16X65) (21X18).
Gearbox type
Gearbox ident. plate
Reduction box torque
GEARBOX AND TYRE SPECIFICATIONS
1.6i 16V
AUTOMATIC 1.4i 1.1iPetrol
HFXX SX Exclusive
Exclusive Exclusive X SX Exclusive
X SX X SX
NFU
KFV
Diesel
165/70 R 14 1,804 m185/60 R15 1,828 m 165/70 R 14 1,804 m185/60 R15 1,828 m
MA/5 AL4 MA/5
20 CP 14 20 CP 15 ou
(*)20 TP 75 20 CP 58
14x6016x63 21x7317x64
21x18
u
1.4 HDi
X SX Exclusive
8HX 8HW 8HV 8HY
165/70 R14 1,804 185/60 R15 1,828 m
MA/5BE4/5
20 CP 54
(2)20 DM 25 20 DM 26
17x61 19x72 19x7721x1822x19
1.4 HDi 16V
C3
Manual gearbox