can Citroen C2 2004 1.G Owner's Manual

Page 61 of 523

Downloaded from www.Manualslib.com manuals search engine 57
GENERAL
MIDDLE EAST
7000 15W50
7000 10W40
7000 15W50
7000 15W50
Saudi Arabia Bahrain
Dubai
United Arab Emirates
IranIsrael Jordan Kuwait
Lebanon Oman Qatar Syria Yemen
LUBRICANTS TOTAL recommended oils
ENGINE OILS
TOTAL ACTIVA
Blended oils for all enginesOils specifically for petrol and
dualfuel petrol / LPG enginesOils specifically for diesel
engines TOTAL ACTIVA DIESEL
ALL TYPES
9000 5W40
7000 10W40

Page 62 of 523

Downloaded from www.Manualslib.com manuals search engine 58
GENERAL
LUBRICANTS TOTAL recommended oils
GEARBOX OILS
ALL TYPES
TOTAL TRANSMISSION BV
norms S.A.E.: 75W80
Part No.: 9730 A2.
TOTAL FLUIDE ATX
TOTAL FLUIDE AT 42
Special oil distributed by
CITROËN
Part No.: 9730 A3
Special oil distributed by
CITROËN
Part No.: 9736 22
TOTAL TRANSMISSION X4Part No.:9730 A4
Manual gearbox and SensoDrive
MB3 automatic gearbox
4HP20 and AL4 autoactive
automatic gearboxes
Transfer box and rear axle
All countries

Page 63 of 523

Downloaded from www.Manualslib.com manuals search engine 59
GENERAL
LUBRICANTS TOTAL recommended oils
POWER STEERING OILS
ENGINE COOLANT FLUID
ALL TYPES
TOTAL FLUIDE ATX
TOTAL FLUIDE DAS
Special oil distributed by
CITROËN
Part No.: 9730 A1
Power steering
All countries
Very cold countries
All countriesCITROËN fluid
Protection: 35C°
2Litres
5Litres
20 Litres
210Litres
9979 70
9979 71
9979 769979 779979 72
9979 73
9979 749979 75 PackCITROËN Part No.
REVKOGEL 2000
GL YSANTIN G33

Page 64 of 523

Downloaded from www.Manualslib.com manuals search engine 60
GENERAL
LUBRICANTS TOTAL recommended oils
BRAKE FLUIDS
Synthetic brake fluid
HYDRAULIC CIRCUIT
WARNING: TOTAL FLUIDE LDS fluid cannot be blended with TOTAL LHM.
WARNING: CITROËN C5: Use exclusively TOTAL FLUIDE LDS suspension fluid.
All countriesTOTAL HYDRAURINCAGE
All countriesCITROËN fluid
0,5Litre
1 Litre
5 Litres
9979 05
9979 069979 07 Pack
CITROËN Part No.
ALL TYPES
Pack
CITROËN Part No.
Norm
Colour
All countries
TOTAL FLUIDE LDS
TOTAL LHM PLUS
TOTAL LHM PLUS
Very cold countries Orange 9979 69
ZCP 830095
9979 20 Green1
Litre

Page 65 of 523

Downloaded from www.Manualslib.com manuals search engine 61
GENERAL
SCREEN WASH FLUID
GREASE
General use
All countriesConcentrated:
250ml
Fluid ready
for use9980 33
9980 06
9980 05ZC 9875 953U
ZC 9875 784U
ZC 9885 077U9980 56
ZC 9875 279U Pack
CITROËN Part No.
LUBRICANTS TOTAL recommended oilsALL TYPES
1Litre
5Litres
Norms NLGI
2
TOTAL MULTIS 2
TOTAL SMALL MECHANISMS
All countries
Note:NLGI = National Lubricating Grease Institute.

Page 66 of 523

Downloaded from www.Manualslib.com manuals search engine 62
GENERAL
ENGINE OIL CONSUMPTION
I Oil consumption depends on:
the engine type.
how runin or worn it is. the type of oil used.
the driving conditions.
II An engine can be considered
RUNINafter:

3,000 miles (5,000 km)for a PETROLengine.
6,000 miles (10,000 km)for a DIESELengine.
III
MAXIMUM PERMISSIBLEoil consumption for a RUNINengine:
0.5 litresper 600 miles (1,000 km)for a PETROLengine. 1 litreper 600 miles (1,000 km)for a DIESELengine.DO NOT INTERVENE BELOW THESE VALUES.
IV OIL LEVEL:The level should NEVER be above the MAX. markon the dipstick after changing or topping up the oil.
This excess oil will be used up rapidly.
It will reduce the engine output and adversely affect the operation of the air circuits and gas recycling
ALL TYPES

Page 137 of 523

Downloaded from www.Manualslib.com manuals search engine 133
ENGINE
XSARA
AUXILIARY EQUIPMENT DRIVE BELT 2002
Powerassisted steering with air conditioning.
Tools.
[1]
Dynamic tensioner peg: () 0188 H
[2]Belt tension measuring instrument: 4122T
Removal.
Peg the dynamic tensioner (1)at "a", using tool [1].
Loosen the screw (2)of the roller (3).
Turn the roller (3)backwards.
Remove the belt.
NOTE:If it can not be pegged at "a":
Loosen the screw (2)of the roller (3).
Using a 7 mmsquare drive, turn the roller (3)at "b".
Peg the tensioner (1)at "a", using tool [1].
NOTE:If the belt is broken:
Support the engine using a jack (insert a wooden block between the housing and the jack).
Remove the right engine support. Using a square drive at
(b)turn the tool (3)in the direction of the arrow "a", so that it can be
pegged at "a"using the tool [1].
B1BP1SKC
Engine: WJY

Page 141 of 523

Downloaded from www.Manualslib.com manuals search engine 137
ENGINE
XSARA
AUXILIARY EQUIPMENT DRIVE BELT 2002
Tools.
[1]
Dynamic tensioner compression lever: ().0188.Z
[2]Peg for dynamic tensioner roller: ().0194.F
Removing.
IMPERATIVE: Respect the safety and cleanliness requirements specific to high pressure
diesel injection engines (HDi).
Remove:
The front RH wheel.
The underengine sounddeadening.
The splashshield.
WARNING: Mark the direction of fitting of the accessories drive belt, if it is to be reused.
Compress the tensioner roller (1)by acting at «a»(clockwise), using tool [1].
Peg at «b», using tool [2].
Keeping the tensioner roller (1)compressed, remove the accessories drive belt.
IMPERATIVE: Check that the rollers (1) and (2) can turn freely (without play and without
tight spots).B1BP2VZD
Engine: 8HZ

Page 144 of 523

Downloaded from www.Manualslib.com manuals search engine 140
ENGINE
140
B1BP2Z6DB1BP2ZCD
AUXILIARY EQUIPMENT DRIVE BELT
Engines: 9HZ 9HY
Tools.
[1]
Dynamic tensioner compression lever: ().0188.Z
[2]Peg for dynamic tensioner roller: ().0194.F
Removing.
Remove the front RH wheel, the underengine sounddeadening and the splashshield.
Vehicle with air conditioning.WARNING:Mark the direction of fitting of the accessories drive belt, if it is to be reused.
Compress the tensioner roller (1)by acting at «a»(clockwise), using tool [1].
Peg at «b», using tool [2].
Remove the accessories drive belt.
IMPERATIVE:Check that the rollers (1) and (2) can turn freely (without play and without tight spots).
Refitting.
WARNING:
Belt to be reused, mark the direction of fitting of the belt.
Refit the accessories drive belt.
Compress the tensioner roller
(1)by acting at «a»(clockwise), using tool [1].
Remove tool [2].
IMPERATIVE: Make sure the belt is correctly positioned in the grooves of the various pulleys.
Complete the refitting in the opposite order to removal.
XSARA PICASSO

Page 218 of 523

Downloaded from www.Manualslib.com manuals search engine 214
ENGINECHECKING AND SETTING THE VALVE TIMING
Engine: WJY
B1EP1EDC
Setting the timing (continued).
NOTE:
If necessary, you can slightly rotate the pinions (10)and (7)anticlockwise in order to engage the belt.
The angular displacement value of the belt in relation to the pinions should not be more than half a tooth.
Remove tool
[5].
Act on the tensioner roller
(8)by its square «a», using tool [6]to check that the camshaft and injection
pump pinions can turn freely.
Position the belt tension instrument
[7]on the belt at «b».
Using tool
[6], act at «a»in the direction opposite to that of engine rotation, to obtain a tension value of
106 ± 2 SEEM units.
Tighten screws
(9), (5)and (6).
Remove tools
[7], [2], [3]and[4].
Rotate the crankshaft
8 timesin the normal direction of rotation.
Peg the flywheel, using tool
[2].
Peg the camshaft hub, using tool
[4].
Peg the injection pump hub, using tool
[3].
Slacken screws
(9), (5)and (6).
Position the belt tension instrument
[7]on the belt at «b».
Using tool
[6], act at «a»in the direction opposite to that of engine rotation, to obtain a tension value of
42 ± 2 SEEM units.
B1EP1EFC
XSARA

Page:   < prev 1-10 11-20 21-30 31-40 41-50 51-60 60 next >