boot Citroen C3 2010 2.G Owner's Manual

Page 8 of 205

1
MONITORING

Warning lamp is on Cause Action/Observations

Maximum
coolant
temperature fi xed red.
The temperature of the
cooling system is too high. Stop as soon as it is safe to do so.
Wait until the engine has cooled down before
topping up the level, if necessary.
If the problem persists, contact a CITROËN
dealer.

Engine oil
pressure fi xed. There is a fault with the
engine lubrication system. Stop as soon it is safe to do so.
Park, switch off the ignition and contact a
CITROËN dealer.

Battery
charge fi xed. The battery charging circuit
has a fault (dirty or loose
terminals, slack or cut
alternator belt, ...). This lamp should switch off when the engine is
started.
If it does not switch off, contact a CITROËN
dealer.

Door(s) open fi xed if the
speed is
below 6 mph (10 km/h).
A door or the boot is still
open. Close the door or boot.
fi xed and
accompanied by an audible signal if the speed is
above 6 mph (10 km/h).

Page 20 of 205


2
MULTIFUNCTION SCREENS
MONOCHROME SCREEN A
Displays on the screen
This displays the following information:
- time,
- date,
- ambient temperature (this fl ashes if there is a risk of ice),
- status of the doors and boot,
- audio sources (radio, CD...),
- trip computer (refer to the "Instruments and Controls" section).
Warning messages (e.g.: "Emission
control system faulty") or information
messages (e.g.: "Boot open") may ap-
pear temporarily. These can be cleared
by pressing the "ESC" button. Controls
From the control panel of your Audio
system, you can:

 press the "MENU" button to gain
access to the main menu ,

 press the "  " or "  " buttons to scroll
through the items on the screen,

 press the "MODE" button to change
the permanent application (date,
audio source...),

 press the "  " or "  " buttons to
change a setting value,

 press the "OK" button to confi rm,
or

 press the "ESC" button to abandon
the operation in progress. Main menu

 Press the "MENU" button to gain
access to the main menu , then
press the "  " or "  " buttons to
scroll through the various menus:
- radio-CD,
- vehicle confi guration,
- options,
- display settings,
- languages,
- units.

 Press the "OK" button to select the
menu required.
Radio-CD
With the Audio system switched on,
once the "Radio-CD" menu has been
selected you can activate or deactivate
the functions linked with use of the ra-
dio (RDS, REG), or the CD (introscan,
shuffl e, CD repeat).
For more information on the "Radio-
CD" application, refer to the Audio sys-
tem part of the "Audio and Telematics"
section.

Page 22 of 205


2
MULTIFUNCTION SCREENS
MONOCHROME SCREEN C
Displays on the screen
This displays the following information:
- time,
- date,
- ambient temperature (this fl ashes if there is a risk of ice),
- status of doors and boot,
- audio sources (radio, CD, USB port, jack socket etc.),
- trip computer (refer to the "Instru- ments and controls" section).
Warning messages (E.g. "Emisions
control system faulty") or information
messages (E.g.: Automatic headlamps
active") may appear temporarily. These
can be cleared by pressing the "ESC"
button. Controls
From your Audio system control panel,
you can:

 press the "MENU" button to gain
access to the main menu ,

 press the "  " or "  " buttons to scroll
through the items on the screen,

 press the "MODE" button to change
the permanent application (trip com-
puter, audio source...),

 press the "  " or "  " buttons to
change a setting value,

 press the "OK" button to confi rm,
or

 press the "ESC" button to abandon
the operation in progress. Main menu

 Press the "MENU" button to gain
access to the main menu :
- audio functions,
- the trip computer,
- personalisation-confi guration,
- telephone (hands-free kit).

 Press the "  " or "  " buttons to se-
lect the menu required, then confi rm
by pressing the "OK" button.
"Audio functions" menu
With the Audio system switched on,
once this menu has been selected you
can activate or deactivate the functions
linked with use of the radio (RDS, REG,
RadioText), the CD (introscan, shuffl e,
CD repeat) or the MP3 player (USB port/
jack socket).
For more information on the "Audio
functions" application, refer to the
Audio system part of the "Audio and
Telematics" section.

Page 42 of 205

4
ACCESS
REMOTE CONTROL KEY
System which permits central unlock-
ing or locking of the vehicle using the
lock or from a distance. It is also used to
locate and start the vehicle, as well as
providing protection against theft.
Unlocking the vehicle
Unfolding the key

 First press this button to unfold the
key.
Unlocking using the remote control
 Press the open padlock to
unlock the vehicle. Unlocking using the key

 Turn the key to the right in the driv-
er’s door lock to unlock the vehicle.
Locking the vehicle
Locking using the remote control
 Press the closed padlock to
lock the vehicle.
Locking using the key

 Turn the key to the left in the driver’s
door lock to lock the vehicle com-
pletely. If one of the doors or the boot
is still open, the central locking
does not take place.
When the vehicle is locked, if it
is unlocked inadvertently, it will
relock automatically after thirty
seconds unless a door or the
boot is open.
The folding and unfolding of the
door mirrors using the remote
control can be deactivated by a
CITROËN dealer.
Locking is confi rmed by fi xed lighting of
the direction indicators for approximate-
ly two seconds.
According to version, the door mirrors
fold at the same time.
Unlocking is confi rmed by rapid fl ashing
of the direction indicators for approxi-
mately two seconds.
According to version, the door mirrors
unfold at the same time.

Page 49 of 205

4
ACCESS
ALARM
System which protects and provides a
deterrent against the theft of your vehi-
cle. It provides two types of protection,
exterior and interior, as well as a self-
protection function.
Exterior perimeter protection
The system detects opening of the ve-
hicle.
The alarm is triggered if anyone tries to
enter the vehicle by forcing a door, the
boot or the bonnet.
Interior volumetric protection
The system detects any variation in the
volume in the passenger compartment.
The alarm is triggered if anyone breaks
a window or moves inside the vehicle.
If you wish to leave a pet in the vehicle
or a window partially open, deactivate
the interior volumetric protection.
Self-protection function
The system detects the putting out of
service of its components.
The alarm is triggered if anyone tries
to put the wires of the siren, the central
control or the battery out of service. Locking the vehicle with full
alarm
Activation

 Switch off the ignition and get out of
the vehicle.

 Lock or deadlock the vehicle using
the locking button on the remote
control.
The alarm is activated; the indicator
lamp on button A fl ashes once per sec-
ond.
The exterior perimeter protection is ac-
tivated, 5 seconds after the locking but-
ton on the remote control is pressed.
The interior volumetric protection is acti-
vated, 45 seconds after the locking but-
ton on the remote control is pressed. Deactivation

 Unlock the vehicle using the unlock-
ing button on the remote control.
The alarm is deactivated; the indicator
lamp on button A switches off.
Do not make any modifi cations
to the alarm system, this could
cause malfunctions. If an opening - door or boot - is
not closed fully, the vehicle is not
locked, but the exterior perim-
eter protection will be activated
after 45 seconds at the same
time as the interior volumetric
protection.

Page 50 of 205

4
ACCESS
Locking the vehicle with exterior
perimeter protection only
Deactivation of the interior
volumetric protection

 Switch off the ignition.

 Within ten seconds, press button A
until the indicator lamp is lit continu-
ously.

 Get out of the vehicle.

 Lock or deadlock the vehicle without
delay using the locking button on
the remote control.
The exterior perimeter protection alone
remains activated; the indicator lamp on
button A fl ashes once per second.
To be effective, this deactivation
must be carried out each time
the ignition is switched off.
Reactivation of the interior
volumetric protection

 Unlock the vehicle using the unlock-
ing button on the remote control.

 Relock the vehicle using the remote
control.
The alarm is activated again with both
types of protection; the indicator lamp
on button A fl ashes once per second. Triggering of the alarm
This is indicated by sounding of the si-
ren and fl ashing of the direction indica-
tors for approximately thirty seconds.
After it has been triggered, both types of
protection are again operational.
If the alarm is triggered ten times
in succession, the eleventh time
will result in it becoming inac-
tive.
If the indicator lamp on button A
fl ashes rapidly, this indicates that
the alarm was triggered during
your absence. When the ignition
is switched on, this fl ashing stops
immediately.
To avoid triggering the alarm
when washing your vehicle, lock
it using the key in the driver’s
door lock. Failure of the remote control

 Unlock the vehicle using the key in
the driver’s door lock.

 Open the door; the alarm is trig-
gered.

 Switch on the ignition; the alarm
stops.
Locking the vehicle without
activating the alarm

 Lock or deadlock the vehicle using
the key in the driver’s door lock.
Malfunction
When the ignition is switched on, light-
ing of the indicator lamp on button A for
ten seconds indicates a siren fault.
Have it checked by a CITROËN dealer.
* According to country.
Automatic activation *
2 minutes after the last door or the boot
is closed, the alarm is activated auto-
matically.

 To avoid triggering the alarm on en-
tering the vehicle, fi rst press the un-
locking button on the remote control.

Page 54 of 205

4
ACCESS
Manual centralised control
System which provides full manual
locking or unlocking of the doors from
the inside.
Locking

 Press button A to lock the vehicle.
The red indicator lamp on the button
comes on.
If one of the doors is open, cen-
tral locking from the inside does
not take place.
Unlocking

 Press button A again to unlock the
vehicle.
The red indicator lamp on the button
switches off. If the vehicle is locked from the
outside, the red indicator lamp
fl ashes and button
A is inactive.

 In this case, use the remote
control or the key to unlock
the vehicle.
Automatic centralised control
System which provides full automatic
locking or unlocking of the doors and
the boot while driving.
You can activate or deactivate this function.
Locking
When the speed exceeds 6 mph
(10 km/h), the doors and the boot lock
automatically. If one of the doors is open, the
automatic central locking does
not take place.
If the boot is open, the automatic
central locking of the doors is
active.
Unlocking

 Above 6 mph (10 km/h), press but-
ton A to unlock the doors and the
boot temporarily. Activation

 Press button A for more than
two seconds.
A confi rmation message appears on the
multifunction screen, accompanied by
an audible signal.
Deactivation

 Press button A again for more than
two seconds.
A confi rmation message appears on the
multifunction screen, accompanied by
an audible signal.

Page 55 of 205

4
ACCESS
BOOT
Opening

 After unlocking the vehicle using the
remote control or the key, pull the
handle and raise the tailgate.
Closing

 Lower the tailgate using the interior
grab handle. -
when the engine is running
,
this warning lamp comes on,
accompanied by a message
on the multifunction screen
for a few seconds,
- when the vehicle is moving (speed
above 6 mph (10 km/h)), this warn-
ing lamp comes on, accompanied
by an audible signal and a message
on the multifunction screen for a few
seconds.
Tailgate release
System for mechanical unlocking of the
boot in the event of a battery or central
locking malfunction.
Unlocking

 Fold back the rear benchseat to
gain access to the lock from inside
the boot.

 Insert a small screwdriver into hole A
of the lock to unlock the tailgate.
If the tailgate is not closed correctly:
Emergency control
To lock or unlock the doors manually in
the event of a malfunction of the central
locking system or failure of the battery.
Locking the driver’s door

 Insert the key in the lock, then turn it
to the left.
Unlocking the driver’s door

 Insert the key in the lock, then turn it
to the right.

 Remove the black cap, located on
the edge of the door, using the key.

 Insert the key in the recess, then
turn it as far as it will go. Unlocking the front and rear
passenger doors

 Pull the interior door opening con-
trol.
Locking the front and rear
passenger doors
 Remove the key and refi t the cap.

 On the rear doors, check that the
child lock is not activated.

Page 56 of 205

4
ACCESS
BOOT
Opening

 After unlocking the vehicle using the
remote control or the key, pull the
handle and raise the tailgate.
Closing

 Lower the tailgate using the interior
grab handle. -
when the engine is running
,
this warning lamp comes on,
accompanied by a message
on the multifunction screen
for a few seconds,
- when the vehicle is moving (speed
above 6 mph (10 km/h)), this warn-
ing lamp comes on, accompanied
by an audible signal and a message
on the multifunction screen for a few
seconds.
Tailgate release
System for mechanical unlocking of the
boot in the event of a battery or central
locking malfunction.
Unlocking

 Fold back the rear benchseat to
gain access to the lock from inside
the boot.

 Insert a small screwdriver into hole A
of the lock to unlock the tailgate.
If the tailgate is not closed correctly:
Emergency control
To lock or unlock the doors manually in
the event of a malfunction of the central
locking system or failure of the battery.
Locking the driver’s door

 Insert the key in the lock, then turn it
to the left.
Unlocking the driver’s door

 Insert the key in the lock, then turn it
to the right.

 Remove the black cap, located on
the edge of the door, using the key.

 Insert the key in the recess, then
turn it as far as it will go. Unlocking the front and rear
passenger doors

 Pull the interior door opening con-
trol.
Locking the front and rear
passenger doors
 Remove the key and refi t the cap.

 On the rear doors, check that the
child lock is not activated.

Page 64 of 205

5
VISIBILITY To avoid causing a nuisance to other
road users, the height of the headlam-
ps should be adjusted in relation to the
load in the vehicle.

0
.
Driver only or driver + front passenger.

- . Intermediate setting

1. 5 people.

- . 5 people + load in the boot.

2. Driver only + maximum authorised
load in the boot.
This position is suffi cient to avoid caus-
ing dazzle.
Higher settings may limit the spread of
light from the headlamps.
The initial setting is position "0" .
HEADLAMP ADJUSTMENT Coupling with the automatic
"Guide-me-home" lighting
Association with the automatic illumi-
nation of headlamps provides "guide-
me-home" lighting with the following
additional options:
- selection of the lighting duration to
15, 30 or 60 seconds in the vehicle
parameters on the multifunction
screen confi guration menu (except
in the case of the monochrome
screen A, for which the duration is
set: 60 seconds),
- automatic activation of "guide- me-home" lighting when automatic
illumination of headlamps is in
operation.
Operating fault In fog or snow, the sunshine sen-
sor may detect suffi cient light.
Therefore, the lighting will not
come on automatically.
Do not cover the sunshine sen-
sor, coupled with the rain sensor
and located in the centre of the
windscreen behind the rear view
mirror; the associated functions
would no longer be controlled.
In the event of a fault
with the sunshine sen-
sor, the lighting comes
on, this warning lamp is
displayed on the instrument panel and/
or a message appears on the multifunc-
tion screen, accompanied by an audible
signal.
Consult a CITROËN dealer.

Page:   1-10 11-20 next >